ACE Issue - while processing merged list

Hi guys,
After aplly the configuration, errors appeared in ACE
“jul 10 2012 19:44:21 : %ace-1-106028: warning: unknown error X while processing merged list. incomplete rule is currently applied on interface vlan120. configuration on this interface needs to be manually reverted”
“config application in progress. this command is queued to the system”
The configuration caused service break of several network components for no apparent reason. During about 10 minutes, which was not possible to perform configuration or rollback.
Can you help me?
Thanks

Hello Luis,
Here you have the explanation of the logging message:
106028
Error Message    %ACE-1-106028: String Incomplete rule is currently applied on
interface interface-name. Manual rollback to a previous access rule configuration
on this interface is needed.
Explanation    Possible String values are:
•WARNING: Access rules memory exhausted while processing component
•WARNING: Unknown error while processing component
Possible values for component are
•Access-list
•Service-policy
•Merged list
For example:
WARNING: Unknown error while processing service-policy. Incomplete rule is currently applied on interface VLAN100. Manual roll back to a previous access rule configuration on this interface is needed.
The access control list (ACL) compilation process has run out of memory, which does not allow new ACL entries to be applied to the specified interface. The ACL configuration downloaded in hardware for that interface may not be in a known state because of this failure.
Recommended Action    The ACL configuration downloaded to the network processors is incomplete. Remove and recreate the affected interface to recover to a known state. If the message is "Access rules memory exhausted," either allocate more memory to that context or remove some of the access group or service policy configuration to reduce the memory usage. If the message is "Unknown error," then there may be an issue with the configuration manager or the ACL merge process.
In order to make sure about what might have happened, then it might be required to replicate the issue and then run some debugs to get more useful data and a #show tech-support
Also, there are some bugs which are also related to the syslog message which you are reporting.
Hope this helps.
Jorge

Similar Messages

Issue while Processing the Huge File in BPEL

Hi,
We are facing an Issue while Processing a Hige file in BPEL Process (More than 1MB File). When i test the files with more than 1500 transactions (More than 1MB file) then the BPEL Process is automatically goes to OFF Mode or it goes to Perform Manually Recovery Queue.
Even we are facing this issue in Production also so we are using UNIX Script to Split the file before place the file in BPEL Input directory.Any Pointers to resolve this issue will be helpful.
Thanks,
Saravana

Hi,
Please find the answers.
1. Currently we are using SOA 10.1.2 Version and JDev10g
2. we are using File Adapeter
3. yes. We used debatching.
4. Yes. I am able to recover from Manual Recovery Queue
5. Please find the error message
<2009-05-21 04:32:38,461> <DEBUG> <ESIBT.collaxa.cube.engine.dispatch> <Dispatcher::adjustThreadPool> Allocating 1 thread(s); pending threads: 1, active threads: 0, total: 83
<2009-05-21 04:32:44,077> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> File : /harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B is ready to be processed.
<2009-05-21 04:32:44,077> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Processing file : /harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B
<2009-05-21 04:32:44,077> <DEBUG> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> onBatchBegin: Batch 'bpel://localhost/ESIBT/BPELProcess_810~1.0//Input5162009.B2B_1242894594000' (/harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B) starting...
<2009-05-21 04:32:44,077> <DEBUG> <ESIBT.collaxa.cube.translation> <TranslatorFactory::log> Inside TranslatorFactory
<2009-05-21 04:32:44,078> <DEBUG> <ESIBT.collaxa.cube.translation> <TranslatorFactory::log> using version attribute = NXSD
<2009-05-21 04:32:44,078> <DEBUG> <ESIBT.collaxa.cube.translation> <TranslatorFactory::log> loading xlator class...oracle.tip.pc.services.translation.xlators.nxsd.NXSDTranslatorImpl
<2009-05-21 04:32:44,081> <DEBUG> <ESIBT.collaxa.cube.translation> <TranslatorFactory::log> class loaded
<2009-05-21 04:32:44,081> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Created translator : oracle.tip.pc.services.translation.xlators.nxsd.NXSDTranslatorImpl@46908ae8
<2009-05-21 04:32:44,098> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Setting up Control dir for debatching error recovery
<2009-05-21 04:32:44,121> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Control dir for debatching error recovery : /opt01/app/ESIBT/oracle/esibt10gR2iAS/BPEL10gR2/iAS/j2ee/home/fileftp/controlFiles/localhost_ESIBT_BPELProcess_810~1.0_/inbound
<2009-05-21 04:32:44,121> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Invoking inbound translation for : Input5162009.B2B
<2009-05-21 04:32:44,121> <DEBUG> <ESIBT.collaxa.cube.translation> <NXSDTranslatorImpl::log> Starting translateFromNative
<2009-05-21 04:32:44,139> <DEBUG> <ESIBT.collaxa.cube.translation> <NXSDTranslatorImpl::log> Done with translateFromNative
<2009-05-21 04:32:44,139> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Completed inbound translation for : Input5162009.B2B
<2009-05-21 04:32:44,139> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> isTextFile : true
<2009-05-21 04:32:44,139> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Translated inbound batch index 1 of file {Input5162009.B2B} with corrupted message count = 1
<2009-05-21 04:32:44,139> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Error Reader created using charset :ASCII
<2009-05-21 04:32:44,139> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Sending message to Adapter Framework for rejection to user-configured rejection handlers : {
fileName=/harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B, startLine=1, startColumn=1, endLine=-1, endCol=-1, Exception=ORABPEL-11167
Error while reading native data.
[Line=1, Col=70] Expected "\t" at the specified position in the native data, while trying to read the data for "element with name HDR_STORE_NUM", using "style" as "terminated" and "terminatedBy" as "\t", but not found.
Ensure that "\t", exists at the specified position in the native data.
<2009-05-21 04:32:44,139> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Setting batchId in NativeRecord to bpel://localhost/ESIBT/BPELProcess_810~1.0//Input5162009.B2B_1242894594000
<2009-05-21 04:32:44,139> <WARN> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> [Read_ptt::Read(Object)] - onReject: The resource adapter 'File Adapter' requested handling of a malformed inbound message. However, the following bpel.xml activation property has not been defined: 'rejectedMessageHandlers'. Please define it and redeploy the business process. Will use the default Rejection Directory file:///opt01/app/ESIBT/oracle/esibt10gR2iAS/BPEL10gR2/iAS/integration/orabpel/domains/ESIBT/archive/jca/BPELProcess_810/rejectedMessages for now.
<2009-05-21 04:32:44,140> <WARN> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> [Read_ptt::Read(Object)] - onReject: Sending invalid inbound message to Exception Handler:
<2009-05-21 04:32:44,140> <INFO> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> Handing rejected message to DEFAULT rejection handler: file:///opt01/app/ESIBT/oracle/esibt10gR2iAS/BPEL10gR2/iAS/integration/orabpel/domains/ESIBT/archive/jca/BPELProcess_810/rejectedMessages since none of the configured rejection handlers [] succeeded.
<2009-05-21 04:32:44,140> <DEBUG> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> Finished persisting rejected message to file system under the name: /opt01/app/ESIBT/oracle/esibt10gR2iAS/BPEL10gR2/iAS/integration/orabpel/domains/ESIBT/archive/jca/BPELProcess_810/rejectedMessages/INVALID_MSG_BPELProcess_810_Read_20090521_043244_0140.dat
<2009-05-21 04:32:44,141> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Setting last error record to : -1
<2009-05-21 04:32:44,141> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Translator has failed to translate any message from batch number: 1
<2009-05-21 04:32:44,141> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Message not published as translation failed: {
File=/harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B, batchIndex=1, PublishSize=1
<2009-05-21 04:32:44,141> <ERROR> <ESIBT.collaxa.cube.activation> <AdapterFramework::Inbound> onBatchFailure: Batch 'bpel://localhost/ESIBT/BPELProcess_810~1.0//Input5162009.B2B_1242894594000' (/harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B) has failed due to: ORABPEL-11167
Error while reading native data.
[Line=1, Col=70] Expected "\t" at the specified position in the native data, while trying to read the data for "element with name HDR_STORE_NUM", using "style" as "terminated" and "terminatedBy" as "\t", but not found.
Ensure that "\t", exists at the specified position in the native data.
<2009-05-21 04:32:44,141> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Deleting file : /harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B after processing.
<2009-05-21 04:32:44,141> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Deleting file : Input5162009.B2B
<2009-05-21 04:32:44,141> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Deleted file : true
<2009-05-21 04:32:44,141> <DEBUG> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Removing file /harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B from files to be processed Map.
<2009-05-21 04:32:44,141> <INFO> <ESIBT.collaxa.cube.activation> <File Adapter::Inbound> Done processing File : /harbinger/prod/xlate/Outbound_Input_LDS_810/Input5162009.B2B
<2009-05-21 04:33:09,698> <DEBUG> <ESIBT.collaxa.cube.engine.data> <ConnectionFactory::getConnection> GOT CONNECTION 4 Autocommit = false
For this error message this shows due to some /t its not picking up the file. but even i am facing the same issue for all the files where load is huge.
Thanks,
Saravana

Issues while processing the BOMs using fm ''CSAP_MAT_BOM_MAINTAIN'

Hi Group,
we are facing issues while processing the BOMs using the basic type(Z-idoc type) for standard type BOMMAT04.
thing is that the segment 'E1STPOM' is defined to contain 1 to 99999 records in it.
when an Idoc is run(say with 150/200 segments of 'E1STPOM'), there was a standard error with error message id PIC01(number : 004) when the Idoc is processed with the Standard function module 'CSAP_MAT_BOM_MAINTAIN'.
the error says 'Error reading material FING_005 . Exception: 0' and Check whether the material number is blocked. but when checked, the Material seems not blocked.
kindly advise how to overcome this error and proceed further.
Regards,
Vishnu

Checj the material status, while its transfer from one server to another server the status should be different

SSAS communication link failure issue while processing cube.

Hi All,
While processing the cube using full process option I am getting the issue communication link failure. If I process each dimension and measure group manually, I am able to succeed. If any one has faced this issue, please let me know.
Thanks,
Moorthy

Please see:
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/e32efab7-f06d-405e-98ea-c6565c98e9bc/cube-is-getting-offline-multiple-times-in-a-day?forum=sqlanalysisservices

Issue while processing xml file

Hi guys -
I am getting error 7000 : null : com.sunopsis.sql.l: Oracle Data Integrator Timeout : connection with URL jdbc:snps:xml ...... while processing data from an xml file which is located in linux directory. I have changed the timout parameter from 30 to 500 in my client. Also modified the userpref.xml as suggested by many in forums but no use. When I checked the failed stage it shows that it gets timed out in 30 seconds. The same when i processed from my local window machine worked fine.
Could you please help me overcome this trouble.? Please help.
Thanks

Hi
You can edit userpref.xml file reside inside bin directory of ODI_HOME (oracledi folder). You need to edit the field name "value" (eg: [30] to [60]). Then restart the application and ODI Agent.
<Object class="com.sunopsis.dwg.dbobj.SnpUserParam">
<Field name="Key" type="java.lang.String"><![CDATA[DEFAULT_REPOSITORY_CONNECTION_TIMEOUT]]></Field>
*<Field name="Value" type="java.lang.String"><![CDATA[30]]></Field>*
<Field name="Label" type="java.lang.String"><![CDATA[Oracle Data Integrator Timeout]]></Field>
<Field name="Type" type="java.lang.String"><![CDATA[com.sunopsis.graphical.userparam.SnpsTextFieldEditor]]></Field>
<Field name="Help" type="java.lang.String"><![CDATA[Timeout used by Oracle Data Integrator for the database connections.]]></Field>
<Field name="Visible" type="boolean"><![CDATA[true]]></Field>
<Field name="Updatable" type="boolean"><![CDATA[true]]></Field>
<Field name="Position" type="int"><![CDATA[4]]></Field>
</Object>
or increase your machine virtual memory
Regards,
Phanikanth

Issue while processing large message using schema exposed as WCFservice

I am using biztalk 2010 and am facing one issue.
I have a schema exposed as WCF service. Used the ecf pubulishing wizard for the same.
When we post a large message using this WCF service it throws http 400 error.
We have isolated the problem to webserver.
Is there a way to update the MEXbindings to set the request message size.
If anyone has faced similar problem before request your help

Hi,
Following settings in the web.config file of the WCF service may help.
<bindings>
    <basicHttpBinding>
        <binding
name="basicHttp" allowCookies="true"
maxReceivedMessageSize="10000000"
maxBufferSize="10000000"
maxBufferPoolSize="10000000">
            <readerQuotas
maxDepth="32"
maxArrayLength="100000000"
maxStringContentLength="100000000"/>
        </binding>
    </basicHttpBinding>
</bindings>
HTH
Sumit
Sumit Verma - MCTS BizTalk 2006/2010 - Please indicate "Mark as Answer" or "Mark as Helpful" if this post has answered the question

Error Ocurred while processing a data cube

While processing a cube i am getting following errors:- please help me out to fix it
1) Errors in the high-level relational engine. The following exception occurred while an operation was being performed on a data source view: Method not found: 'System.Threading.Tasks.Task`1<!!0> System.Threading.Tasks.Task.FromResult(!!0)'..
2)Errors in the high-level relational engine. The following exception occurred while an operation was being performed on a data source view: .
3)Errors in the OLAP storage engine: An error occurred while the dimension, with the ID of 'Dimension Metier', Name of 'Dimension Metier' was being processed.
4)Errors in the OLAP storage engine: An error occurred while the 'Metier ID' attribute of the 'Dimension Metier' dimension from the 'MultidimensionalProject1' database was being processed.
5)Internal error: The operation terminated unsuccessfully.
6)Server: The current operation was cancelled because another operation in the transaction failed.
thank you

Hi Immortal12,
What's the version of your SQL Server Analysis Services? Are you encountered this issue while process the cube in SQL Server Management Studio? Please elaborate your scenrio with more deail.
Currently, we can't figure out the root casue of this issue. So, please help to collect more log information which are benefit for us to do further investigation. Here are some good articles to collect SSAS log informtion:
Error Configuration for Cube, Partition, and Dimension Processing (SSAS - Multidimensional):
http://msdn.microsoft.com/en-us/library/ms180058.aspx
Data collection for troubleshooting Analysis Services issues:
http://blogs.msdn.com/b/as_emea/archive/2012/01/02/initial-data-collection-for-troubleshooting-analysis-services-issues.aspx
Regards,
Elvis Long
TechNet Community Support

Application Builder hangs on Processing Merge Errors.vi

I am having a problem building my applciation as an executeable in 8.2.1. During the build process, LabVIEW hangs indeffinately while Processing Merge Errors.vi. I have mass compiled my source directory, and my LabVIEW directory. I have even repaired all of the NI software that I have installed. I have also created a new project and build specification from scratch in case that was corrupted. I created a test project where the only VI was a call to Merge Errors.vi and this build just fine into an .exe. I am at a loss to what the problem is or how I can fix it. Any help would be greatly appreciated.
thanks,

Hi Faraclas,
What operating system are you using? Does it only hang when you have this vi? Can
you create an executable without this vi?
Juan Galindo
Applications Engineer
National Instruments

SharePoint List Error :[DataSource.Error] SharePoint: Request failed: The remote server returned an error: (500) Internal Server Error. (An error occurred while processing this request.)

When I connect to the SharePoint site that contains the lists I need to build my query from , Power Query enumerates the list and displays them in the tool. I can click on the system tables and view the records but any table
in the list I created returns this error.
I can connect fine with InfoPath
[DataSource.Error] SharePoint: Request failed: The remote server returned an error: (500) Internal Server Error. (An error occurred while processing this request.)
thank you for your help
Andrew

Hi Andrew. In order for us diagnose this issue, you'll need to capture some network traces using a tool such as Fiddler and share them by sending a Frown.
To capture a trace using Fiddler, start Fiddler, enable the Tools > Fiddler Options > HTTPS > Decrypt HTTPS traffic option, start the capture, reproduce your issue, then stop and save the capture. You can find more information here.
Once you've done that, please send a Frown through the Power Query ribbon and attach the traces.
Thanks,
Ehren

Issue while archiving the processed file in sender communication channel using SFTP adapter

Hi All,
In one of my scenario (File to IDOC), we are using SFTP sender communicationchannel.
we are facing an issue while archiving the processed file. Some times PI processed the file successfully but unable to archive it and in the next poll PI process & archives the same file successfully which will creates duplicate orders in ECC.
Please let us know how to resolve this issue.

Hi Anil,
Refer Archiving concepts in below links.
http://help.sap.com/saphelp_nw73/helpdata/en/44/682bcd7f2a6d12e10000000a1553f6/content.htm?frameset=/en/44/6830e67f2a6d12e10000000a1553f6/frameset.htm
http://scn.sap.com/docs/DOC-35572
Warm Regards,
DNK Siddhardha.

Issue In Lock Box while processing mutiple files at a time:Tcode FLBP

Hi Experts,
I have an issue while executing Program RFEBLB30 (or tcode FLBP) for Variant which contains more than one file,means.Variant contains two files ,One file contains Single cheque details and other file contains multiple cheques.
the final output showing wrong values in Total advice & cheque amount.
when we process single file at a time(whether file has single or multiple cheque details) we are not facing any issue.
Thanks & Regards,
Veera.

It seems that there is no standard solution there.
Why do you have 2 files, is this 2 different batches ? Are they from the same day ? Can you ask the bank to bundle them ? Can you run FLBP twice a day to pick uop 1 file only ?
In FLBP standard selection fields available are
- Destination / Origin
- Lockbox
- Date
You can maybe also configure a dummy lockbox, use an exit to change it when you process the file.

Error Event ID 11 The KDC encountered duplicate names while processing a Kerberos authentication request.

I've been noticing The Error with event ID 11 popping up a lot on our domain controllers:
The KDC encountered duplicate names while processing a Kerberos authentication request.
When running setspn -X it says that it found 111 groups of duplicate SPNs. However, when going through the list, it references domain service accounts that are used to run our SQL Server services. We have about 50 remote locations and each of them has 3
machines participating in a SQL mirror (principal, mirror, witness) and they all run the SQL Server service on the same account (1 account per location).
We haven't experienced any issues at all but I was wondering if this could cause problems or if we are straying from best practice. Any advice is welcome. Thanks!

I believe what you should do to follow best practice is to provide unique SPNs for each SQL server, which will also provide increased security, and to do that you must create individual service account for each SQL server so it can associate that
account with that server's SPN.
Here's more on it to help guide you. Read Paul's comments, as well as other suggestions in the following thread:
event ID 11 There are multiple accounts with name MSSQLSvc/xxxxxx
http://social.technet.microsoft.com/Forums/windowsserver/en-US/8df35316-23ba-48ba-aa3e-2249fcbfecbc/event-id-11-there-are-multiple-accounts-with-name-mssqlsvcxxxxxx?forum=winserverDS
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights.

Error while processing your request while opening PDF in ESS

Hi,
   I had one more issue in Travel and expenses -->Movement Order
   we are not able to open the PDF ,when we are trying to open that getting the below error
    In R/3 also we are not able to open the PDF ,but in portal side I am getting below error.
          Guys please share your inputs.....
               what are the steps need to do for resolve the issue.
    Eror while processing your request!
What has happened?
The call of URL http://rcihwrepa1v.hastinapur.res:8003/sap/bc/webdynpro/sap/FITV_TRIP_FORM/ has been terminated due to an error.
uF0A7     The following error occurred in system REP : Syntax error in program /1BCDWB/SAPLSM00000007 .
uF0A7     The error occurred on application server rcihwrepa1v_REP_03 and in work process 0 .
uF0A7     The termination type was: RABAX_STATE
uF0A7     The ABAP call hierarchy was:
Form: GET_REQUEST_FORM of program SAPLPTRM_WEB_FORMS
Form: GET_REQUEST_FORM of program SAPLPTRM_WEB_FORMS
Function: PTRM_WEB_FORM_PDF_GET of program SAPLPTRM_WEB_FORMS
Function: PTRM_WEB_FORM_GET of program SAPLPTRM_WEB_FORMS
Method: DISPLAY_FORM of program CL_FITV_POWL_UTIL=============CP
Method: DISPLAY_FORM of program /1BCWDY/9BDOSL87UR8KAUWCEZMQ==CP
Method: IWCI_FITV_UI_DISPLAY_FORMS~DISPLAY_FORM of program /1BCWDY/9BDOSL87UR8KAUWCEZMQ==CP
Method: ONACTIONSHOWDATA of program /1BCWDY/9BDOSL87UR8KAUWCEZMQ==CP
Method: IF_WDR_VIEW_DELEGATE~WD_INVOKE_EVENT_HANDLER of program /1BCWDY/9BDOSL87UR8KAUWCEZMQ==CP
Method: INVOKE_EVENTHANDLER of program CL_WDR_DELEGATING_VIEW========CP
What can you do?
uF0A7     In the case of termination type RABAX_STATE, you will find more information on the cause of termination in system REP in transaction ST22.
uF0A7     In the case of termination type ABORT_MESSAGE_STATE, you will find more information on the cause of termination on application server rcihwrepa1v_REP_03 in transaction SM21.
uF0A7     In the case of termination type ERROR_MESSAGE_STATE, you can search for more information in the trace file for the work process 0 in transaction ST11 on application server rcihwrepa1v_REP_03 . An analysis of the trace files for other work processes may be necessary.
uF0A7     If you do not yet have any user ID, contact your system administrator.
Error Code: ICF-IE-http -c: 500 -u: 1502 -l: E -s: REP -i: rcihwrepa1v_REP_03 -w: 0 -d: 20120215 -t: 121310 -v: RABAX_STATE -e: SYNTAX_ERROR -X: -x:
HTTP 500 - Internal Server Error
Your SAP Internet Communication Framework Team
Regards,
Sony.
<< moved by moderator - check out the list of other forums on top of portal forum >>
http://forums.sdn.sap.com/thread.jspa?threadID=1239838&tstart=0
Second move of threads opened by your user ID today. Please check the list of forums and open a thread in the most relevant one.
Edited by: Anja Engelhardt on Feb 15, 2012 1:33 PM
Thank you Anja
Edited by: sonyepmdm on Feb 15, 2012 1:47 PM

this is to do with ADS config
Can you please enable the ADS Trace as described in SAP note:
#846610 and reproduce the problem?
and
the destination possibly service is not working.
Please follow note:
#915399

InfoPath form, rich text fields, "There was a form postback error" InvalidOperationException, There has been an error while processing the form

Using InfoPath 2013 browser enabled form.
I am getting the above error on ALL Infopath Designed Rich Text fields, where the "Cannot be blank" attribute is set.
To reproduce it, I create a custom list and custom list form with InfoPath 2013. I add 2 Rich Text fields and enable "cannot be blank". To raise the error, I put some data in the RT field. Skip to another field (so focus is changed and a postback
occurs), then back to original field to delete the contents (to raise the validation).
I originally thought it was associated with the HTMLCHKR.DLL not being registered (and I have re-registered it just in case), but the exception I get from the ULS logs reads (it is from a list AFTER I have re-registered the DLL):
There was a form postback error. (User: 0#.w|myDomain\jc, Form Name: Template, IP: , Request: h t t p ://MyWebApp/MySite/Lists/rtAfterHtmlCHkrReg/Item/newifs.aspx?List=2212ff41-77b4-445b-931b-d7e538c9da91&Source=h t t p://MyWebApp/MySite/Lists/rtAfterHtmlCHkrReg/AllItems.aspx&RootFolder=&Web=3db49106-bdca-47bb-b4cd-a549d2d86aa7,
Form ID: urn:schemas-microsoft-com:office:infopath:list:-AutoGen-2015-01-16T21:51:48:853Z, Type: InvalidOperationException, Exception Message: No content generated as the result of the operation.) 8cc5e09c-3665-903b-575a-faaac506c40a
I noticed that errors associated with the HTMLCHKR.DLL not being registered would have some sort of COM exception (example: TYPE_E_LIBNOTREGISTERED or REGDB_E_CLASSNOTREG)
I also should mention that this problem started happening about 3 weeks ago. We have extended the web application to handle HTTPS on the intranet zone (we had a reverse proxy project that did not eventuate) - would that cause something? How can I do further
checking?

Hi,
I have done a test in my SharePoint, and I met the same issue with you.
I created a custom list and custom list form with InfoPath 2013. I added 2 Rich Text fields and enabled "cannot be blank". I put some content in the RT field, then delete the contents, I got the error message:"there has been an
error while processing the form."
Here is a similar post said that executing the command: regsvr32 "C:\Program Files\Common Files\Microsoft Shared\
OFFICE14\htmlchkr.dll" will solve the issue.
https://social.msdn.microsoft.com/Forums/en-US/eb2e0f6e-c8e4-4e92-ac5e-a09d72759eda/rich-text-field-error-in-webform?forum=sharepointcustomizationprevious
But I just disabled "cannot be blank", and it solved the issue.
Best Regards,
Lisa Chen
Lisa Chen
TechNet Community Support

Issue while integrating OID and BPEL.

Issue while integrating OID and BPEL.
We followed steps mentioned in for integration. WE have two SoA instances, home, oc4j_soa.
http://download-uk.oracle.com/docs/cd/B31017_01/integrate.1013/b28982/service_config.htm#BABIBGFF
Before running configure_oid.bat script, we changed jazn.xml to include the contents that are available in home\jazn.xml.
The contents we replaced contain
<jazn xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://xmlns.oracle.com/oracleas/schema/jazn-10_0.xsd" schema-major-version="10" schema-minor-version="0" provider="LDAP" location="ldap://myhost:389" default-realm="my-realm" >
     <property name="custom.sso.url.login" value="/jsso/SSOLogin" />
     <property name="ldap.user" value="orclApplicationCommonName=jaznadmin2,cn=JAZNContext,cn=products,cn=OracleContext" />
     <property name="ldap.password" value="{903}dA0r1HydR5qIhjAn2OCLMSWlFXeLdV//sCLFNwSfWhE=" />
     <property name="custom.sso.key.alias" value="ssoSymmetricKey" />
     <property name="idm.token.asserter.class" value="oracle.security.jazn.sso.SSOCookieTokenAsserter" />
     <property name="idm.token.collector.class" value="oracle.security.jazn.sso.SSOCookieTokenCollector" />
     <property name="idm.token.type" value="HTTP_COOKIE" />
     <property name="idm.token.collector.cookie.1" value="ORA_OC4J_SSO" />
     <property name="custom.sso.url.logout" value="/jsso/SSOLogout" />
     <property name="ldap.protocol" value="no-ssl" />
     <property name="idm.authentication.name" value="JavaSSO" />
</jazn>
configure_oid.bat ran successfully.
But when we try restarting SoA, it gives error. If we replace the above to point to XML-based jazn then SoA starts succcessfully.
Please let us know if we are missing anything.
Regards
Yatan

*1.) No I am not able to complete 2.1.3.3 step 3 the*
work list application is showing "authentication fail"
user look up is showing "unable to find the realm with name my-realm "
*2.) After 2.1.3.3 step 2, if I try restarting the SOA suite, it throws following error.*------------------------------------------------------------------------------------------------------------------------------------------------------------
Configuration information
Running in C:\product\10.1.3.1\OracleAS_1
Operation mode:Startup, App Server, No Enterprise Manager, Single Instance
Oracle home:C:\product\10.1.3.1\OracleAS_1
Oracle home name:Unnamed
Instance name:ias_soa.myhost
Instance type:allProducts
Version:10.1.3.1.0
Uses infrastructure:false
Not an infrastructure instance, no infrastructure information available
Components:[j2ee, apache, orabpel, oraesb, owsm, Wsil]
2009-06-29 04:10:49.962--Begin log output for Mid-tier services (ias_soa.myhost)
2009-06-29 04:10:49.962--Processing Step: starting OPMN
2009-06-29 04:10:57.493--Processing Step: starting OPMN managed processes
2009-06-29 04:11:22.806--End log output for Mid-tier services (ias_soa.myhost)
An unknown OPMN error has occured
oracle.appserver.startupconsole.model.ConsoleException: An unknown OPMN error has occured
     at oracle.appserver.startupconsole.control.OPMNController.doStart(OPMNController.java:140)
     at oracle.appserver.startupconsole.control.Controller.start(Controller.java:69)
     at oracle.appserver.startupconsole.control.GroupController.doStart(GroupController.java:47)
     at oracle.appserver.startupconsole.control.Controller.start(Controller.java:69)
     at oracle.appserver.startupconsole.view.controller.ControllerAdapter.start(ControllerAdapter.java:30)
     at oracle.appserver.startupconsole.view.controller.MasterControlAdapter.run(MasterControlAdapter.java:94)
     at oracle.appserver.startupconsole.view.Runner.main(Runner.java:39)
Caused by: oracle.appserver.startupconsole.model.ConsoleException: There are some errors while stopping the following components. Refer to the generated error report for more details.
==================================================
ias-component: default_group
process-type: oc4j_soa
process-set: default_group
Error Message:failed to start a managed process after the maximum retry limit
==================================================
     at oracle.appserver.startupconsole.control.OPMNController.doStart(OPMNController.java:139)
     ... 6 more
Caused by: oracle.ias.opmn.optic.OpticControlException: Error from opmn during process control operation
     at oracle.ias.opmn.optic.AbstractOpmnEntity.runCommand(AbstractOpmnEntity.java:174)
     at oracle.ias.opmn.optic.AbstractOpmnEntity.start(AbstractOpmnEntity.java:110)
     at oracle.appserver.startupconsole.control.OPMNController.doStart(OPMNController.java:97)
     ... 6 more
Exception caused by
There are some errors while stopping the following components. Refer to the generated error report for more details.
==================================================
ias-component: default_group
process-type: oc4j_soa
process-set: default_group
Error Message:failed to start a managed process after the maximum retry limit
==================================================
oracle.appserver.startupconsole.model.ConsoleException: There are some errors while stopping the following components. Refer to the generated error report for more details.
==================================================
ias-component: default_group
process-type: oc4j_soa
process-set: default_group
Error Message:failed to start a managed process after the maximum retry limit
==================================================
     at oracle.appserver.startupconsole.control.OPMNController.doStart(OPMNController.java:139)
     at oracle.appserver.startupconsole.control.Controller.start(Controller.java:69)
     at oracle.appserver.startupconsole.control.GroupController.doStart(GroupController.java:47)
     at oracle.appserver.startupconsole.control.Controller.start(Controller.java:69)
     at oracle.appserver.startupconsole.view.controller.ControllerAdapter.start(ControllerAdapter.java:30)
     at oracle.appserver.startupconsole.view.controller.MasterControlAdapter.run(MasterControlAdapter.java:94)
     at oracle.appserver.startupconsole.view.Runner.main(Runner.java:39)
Caused by: oracle.ias.opmn.optic.OpticControlException: Error from opmn during process control operation
     at oracle.ias.opmn.optic.AbstractOpmnEntity.runCommand(AbstractOpmnEntity.java:174)
     at oracle.ias.opmn.optic.AbstractOpmnEntity.start(AbstractOpmnEntity.java:110)
     at oracle.appserver.startupconsole.control.OPMNController.doStart(OPMNController.java:97)
     ... 6 more
<?xml version='1.0' encoding='WINDOWS-1252'?>
<response>
<msg code="-82" text="Remote request with weak authentication.">
</msg>
<opmn id="bg1ws0008:6201" http-status="206" http-response="2 of 3 processes started.">
<ias-instance id="ias_soa.myhost">
<ias-component id="default_group">
<process-type id="home">
<process-set id="default_group">
<process id="91427687" pid="4148" status="Alive" index="1" log="C:\product\10.1.3.1\OracleAS_1\opmn\logs\\default_group~home~default_group~1.log" operation="request" result="success">
<msg code="0" text="">
</msg>
</process>
</process-set>
</process-type>
<process-type id="oc4j_soa">
<process-set id="default_group">
<process id="91427688" pid="5856" status="Init" index="1" log="C:\product\10.1.3.1\OracleAS_1\opmn\logs\\default_group~oc4j_soa~default_group~1.log" operation="request" result="failure">
<msg code="-21" text="failed to start a managed process after the maximum retry limit">
</msg>
</process>
</process-set>
</process-type>
</ias-component>
<ias-component id="HTTP_Server">
<process-type id="HTTP_Server">
<process-set id="HTTP_Server">
<process id="91427686" pid="5140" status="Alive" index="1" log="C:\product\10.1.3.1\OracleAS_1\opmn\logs\\HTTP_Server~1.log" operation="request" result="success">
<msg code="0" text="">
</msg>
</process>
</process-set>
</process-type>
</ias-component>
</ias-instance>
</opmn>
</response>
*3.) opmnctl status -all ?*
C:\product\10.1.3.1\OracleAS_1\opmn\bin>opmnctl status -all
Usage:
opmnctl [<scope>] status [<options>] [host port]
Notes:
- if host,port is specified, contact opmn on host,port;
otherwise, contact opmn in local ias instance.
scope:
@instance(:name)*|@cluster
scope specifies how far to apply the query. To apply the query to
all known iAS Instances, specify "cluster". To apply the query
to a specific set of 1 or more iAS Instances, specify
"instance(:instname(:instname...))". If no names are supplied
in an instance scope string then the request is applied to the
"local" instance. In this context, "local" means the instance
containing the opmn server handling the request.
Default: local iAS Instance.
Options:
[ias-component|oc4j-group]=id
- filter output by ias-component name
- i.e. filter output by oc4j-group name
-l - pre-selected long output format:
%cmp32%prt18%pid7R%sta8%uid10R%mem8R%utm9R%por
-fmt <fmtlist> - output format (see details below)
Option "-fmt <fmtlist>" and "-l" are mutually exclusive
-fsep <string> - field separator (default:" | ")
-rsep <string> - record separator (default:"\n")
-noheaders - don't print a header
-c <count> - number of times to print status (default:1)
-i <nsecs> - seconds between each print (default:5)
-app [-l] - application status (optional long format)
-port - opmn "request" host and port (scope
argument invalid)
Format String Syntax:
<fmtlist> - A single string containing one or more statistic
identifiers concatenated together where each identifier has
the following format: %<statname>[<width>[<justification>]]
default: %cmp32%prt18%pid7R%sta8
<statname> - Must be one of the following:
ins - iAS Instance Name
cmp - iAS Component Id
prt - Process Type Id
prs - Process Set Id
idx - Index of process in Process Set
pid - OS Process Identifier
uid - Opmn Unique Id
typ - Name for this kind of process
sta - Process status
stm - start time (ms)
utm - up time (ms)
cpu - cpu time (ms)
mem - memory used (Kb)
pme - private memory (Kb)
sme - shared memory (Kb)
hpz - heap size (Kb)
por - Port List
<width> - The number of columns to use for this field. Output
less than this value will receive padding according to the
specified justification. Output more than this value will
be truncated and terminated with '~'.
default: the width of each datum
<justification> - How to justify output when less than the width.
Must be L, R, or C (left, right, or center justification).
default: L
4.) SOA Suite version ? *10.1.3.1.0*
5.) Did you manually tweak some configuration file or followed the documentation as it is ? I have followed the document as it is.
I have changed only jazn.xml available in ..j2ee/oc4j_soa suite to have the below section: This section was copied from jazn.xml of ..j2ee/home directory that has been automatically updated after running configure_oid.bat file
<jazn xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://xmlns.oracle.com/oracleas/schema/jazn-10_0.xsd" schema-major-version="10" schema-minor-version="0" provider="LDAP" location="ldap://myhost:389" default-realm="myrealm" >
     <property name="custom.sso.url.login" value="/jsso/SSOLogin" />
     <property name="ldap.user" value="orclApplicationCommonName=jaznadmin2,cn=JAZNContext,cn=products,cn=OracleContext" />
     <property name="ldap.password" value="{903}dA0r1HydR5qIhjAn2OCLMSWlFXeLdV//sCLFNwSfWhE=" />
     <property name="custom.sso.key.alias" value="ssoSymmetricKey" />
     <property name="idm.token.asserter.class" value="oracle.security.jazn.sso.SSOCookieTokenAsserter" />
     <property name="idm.token.collector.class" value="oracle.security.jazn.sso.SSOCookieTokenCollector" />
     <property name="idm.token.type" value="HTTP_COOKIE" />
     <property name="idm.token.collector.cookie.1" value="ORA_OC4J_SSO" />
     <property name="custom.sso.url.logout" value="/jsso/SSOLogout" />
     <property name="ldap.protocol" value="no-ssl" />
     <property name="idm.authentication.name" value="JavaSSO" />
</jazn>
instead of
<jazn xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="http://xmlns.oracle.com/oracleas/schema/jazn-10_0.xsd" schema-major-version="10" schema-minor-version="0" provider="XML" location="./system-jazn-data.xml" default-realm="jazn.com">

     <property name="idm.authentication.name" value="JavaSSO"/>
     <property name="idm.token.asserter.class" value="oracle.security.jazn.sso.SSOCookieTokenAsserter"/>
     <property name="idm.token.collector.class" value="oracle.security.jazn.sso.SSOCookieTokenCollector"/>
     <property name="idm.token.type" value="HTTP_COOKIE"/>
     <property name="idm.token.collector.cookie.1" value="ORA_OC4J_SSO"/>

     <property name="custom.sso.url.login" value="/jsso/SSOLogin"/>
     <property name="custom.sso.url.logout" value="/jsso/SSOLogout"/>
     <property name="custom.sso.key.alias" value="ssoSymmetricKey"/>
</jazn>

ACE Issue - while processing merged list

Similar Messages

Maybe you are looking for