Acquiring and plotting data from USB raw

Hi,
I am new to Labview. I have a 3rd party RFID
device which i intend to acquire the frequency waveform from the device
through using Labview. Since as a beginner, i use the spectrum analyser
in the "example" section to start off with and now has error in getting
the correct Visa USB raw to connect my device. The program intiallly
used Visa instrument as the visa resource name but when i changed the
input to the USB raw input there is a class conflict error that says
"You have connected a refnum of one type to a refnum of another type and
both types are members of some class hierarchy, but there is neither a
simple up cast nor type cast between the two classes."
For the
USB raw setting, i have already configured the device using the
NI-driver wizard to install the USB raw and tested it through the MAX.
So now i believe the problem should be wiring of USB raw to the entire
spectrum analyser example. Attached is the spectrum analyzer example.
Really hope to get help on this matter. Thank you.
Attachments:
Template - Spectrum Analyzer Acquire Trace.vi ‏25 KB

The example you posted is based on serial port communication. From your software point view, everything is based on RS232. This is quite common in instrumentation. As RS232 is simple compared to USB. The software driver on your host PC emulate a virtual RS232 port.
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far)

Similar Messages

Acquiring High resolution data from usb mouse movement

Is there a way of acquiring high resolution data from the movement of a usb mouse? I have a NI PCI 6221 daq card to use. I have a Pentium 4 PC with 1 Gb of RAM. I need to get the position, velocity and acceleration of the mouse.
Is there a way to do it with the above hardware.
Thanks in advance

I don't see how you could use a PCI-6221 to get high resolution mouse movement measurements. The PCI-6221 can acquire voltages at up to 250kS/s, but what voltage would you measure? It could also read in digital data at 1MHz, but you would have to be able to understand the USB communication protocol your mouse uses, and I doubt that your mouse vendor will give out that information. You might be able to take your mouse apart and hook up leads to the sensors around the trackball and do a sort of quadrature encoder application, but there's no guarantee we're dealing with TTL digital signals here (you might even be using an optical mouse!).
Your best option - and I have no idea how good this option is - is to use the driver already installed for your usb mouse. What software application are you going to use to program your application that will measure the mouse movements?
If you would consider using LabVIEW, you could set up an event structure to capture mouse movements across the front panel. Each event registered includes a timestamp from the CPU's millisecond clock as well as the coordinates of the mouse. If you stored up a buffer of previous mouse positions and times, you could infer a velocity, perhaps with the help of interpolation functions.
All of this would have somewhere on the level of millisecond timing accuracy. Were you envisioning something else?
Jarrod S.
National Instruments

"I want to acquire and display data from 89C51 micro controller using RS 232 port"

I am using 89c52 for data acquisition and control for photo diode array. I would like to do the same using RS-232 and micro-controller 89c52. I would like to generate two different control pulses (clock and trigger) and I am digitizing my analog data using on-board ADC, the data for which I would like to read using Labview and store it in a file also display the waveform of acquired data. Please reply.

Nice project, we do that all day long here. What is your problem exactly?
The 89C52 has a UART you can use to write commands and read data. It is fairly straightforward to write a command processor for the uC and implement a command set. Is it the computer or the uC that generates the control pulses?
LabVIEW, C'est LabVIEW

How to acquire and display data from labview to excel simultaneously

hello,
I am using the NI-DAQ to measure the falling edges of a clock and display them into a table. What I need is to display these data in a table in excel while the program is running. In addition, when I receive a pulse from an external clock, for which I have created a digital channell, the data must be logged in a different column. In other words, every time I receive a pulse the data must be stored in the adjacent column in excel.

Hello Evangelos,
As far as I know and have experienced, it is not possible to access a spreadsheet file (or any file, for that matter) by two programs at the same time, you will get an error.
Also, a couple of observations on your code:
A constant wired to a case selector of a case structure makes no sense as the false case will never be executed.
Move the DAQmx Read from your Digital Input task into the while loop, as the DAQmx Read will only read once and the wire won’t get information in or out of a while loop as long as the while loop is iterating.
Regards,
Daniel REDS
RF Systems Engineer
Help us grow.
If a post solves your question, mark it as The Solution.
If a post helps, give Kudos to it.

How to send TTL output AND acquire AI voltage data using USB-6211

Hello,
I am relatively new to Labview, so please bear with me. I have a research application involving 2 pressure transducers and a high-speed camera. I wish to acquire analog voltage data from the 2 pressure transducers. However, at the start of the acquisition, I will need to send a single TTL output to trigger the camera. This TTL pulse must be sent out at exactly the same time that the AI acquisition begins, in order to ensure that my 2 pressure measurements and camera images are 'synchronized' in time.
Is this possible on the USB-6211 running with LabView 8.20? I currently have a fairly simple LabVIEW vi that uses a software trigger to start an AI acquisition - I have attached it with hopes that it may help anyone willing to assist me. I would prefer to be able to simply add something to it so that it will output a TTL pulse at the start of the acquisition.
Thank you in advance.
Regards, Larry
Message Edited by Larry_6211 on 12-19-2008 11:24 AM
Attachments:
USB6211_v1.vi ‏212 KB

Hi All,
I'd like to clear a few things up. First, you'll find that if you try to set the delay from ai start trigger and delay from ai sample clock to 0, you'll get an error. Due to hardware synchronization and delays, the min you can set is two. Note that when I say two, I am referring to two tick of the AI Sample clock timebase, which for most acquisitions is the 20MHz timebase. I modified a shipping example so you can play around with those delays if you want to - I find that exporting the signals and looking at them with a scope helps me visualize what is going on. The Manual has some good timing diagrams as well but it looks like you've already hit that. The defaults would give you a delay of 250ns from the start trigger - is this too high for your situation? What is an acceptable delay? I tend to think that "exactly the same time" is a measure of how precise rather than an absolute (think delays in cable length making a difference.)
With all that in mind, I see a few options:
Start your camera off of the AI start trigger (an internal signal) and just know it is 250 ns before your first convert.
Export the convert clock to use as a trigger. This assumes your camera can ignore the next set of convert clocks.
More complicated option: Internally you have an ai start trigger, sample clock and convert clock. From your start trigger to the first convert is 250ns but if you export your convert clock you're going to get future convert clocks as well. One option would be to generate a single triggered pulse using a counter (start with the Gen Dig Pulse-Dig Start.vi example) with the AI start trigger as the trigger for the counter, an initial delay of 250 ns, and a high time of whatever you want it to be. This should give you a singe pulse at very close to same time (on the order of path delays) as your first convert clock.
Hope this helps,
Andrew S
MIO DAQ Product Support Engineer
Getting Started with NI-DAQmx
Measurement Fundamentals
Attachments:
Acq&Graph Voltage-Int Clk.vi ‏37 KB

Logging Data from USB 6000 without Labview

Greetings all.
I am sure this questions is buried somewhere, so I apologize if I am repeating a question that has already been posed and addressed. If this is a redundant question, simply pointing me to the relavent post will help.
I've got a USB 6000. I've got it set up and working just fine in a MAX test panel. Is there any way to log acquired data to any sort of file without Labview, measurment studio, signal express, or lab windows/cvi? In a similar note, being able to acquire and log data without a different programming routine like .Net or C++. Maybe there is a way to create a task and call it from an excel macro?
I know I've dug my own grave by getting the bottom of the like USB DAQ. However, even with the USB-6000, there must be a way to log the data being acquired without needing to make additional investments in development software. Not trying to do anything fancy like triggering or data manipulation, I'm just looking to log measured voltages to file and do post processing in Excel.
Again, I am sure this (or at least a similar) question has been posed before. Any help would be appreciated.
Thanks,
Ben

I think Signal Express is what you really want to use here. It was designed for the very high level, simple measurement acquisition.
In MAX, you can set up the task to log to a TDMS file. With that enabled, you should be able to just let Signal Express run your task and then tell it to stop whenever you want it to and the data will be logged.

End point data from usb 2.0

plz does anybody tell me how to read the data from end point 2,4,6 or 8 from usb raw 2.0 (min 4 byte to max 1024) or how to confirue the usb visa properties? plz it's very urgent.
thanking you.
robin

Hello Robin,
I guess you are using LabVIEW. Have you tested the example USB Raw –Bulk.vi from LV NI Example Library? This example should work properly for you.LAbVIEW>>Help>>Find Examples>>search for USB >>choose USB Raq-Bulk.vi
Before you run this VI, install a USB RAW device and configure NI Measurement & Automation Explorer (MAX) to recognize the USB device. You can read to and write from the USB RAW device only after you install and configure the USB RAW device and open a session to the device.
Plus.
In my opinion, the attached KnowledgeBase could be helpful. This document includes a lot of details about your issue.
How Can I Communicate With a Device Using NI-VISA USB RAW Mode?
http://digital.ni.com/public.nsf/allkb/E3A2C4FE42D7ED0D86256DB7005C65C9?OpenDocument
Best regards,
AmirG

How to read a data from USB port using JAVA

hi all,
i need to know how to read a data from USB port using java. any API are available for java ?.........please give your valuable ideas !!!!!!!!!
Advance Thanks!!

You can do this. Please use this link
[http://www.google.co.in/search?hl=en&client=firefox-a&rls=org.mozilla%3Aen-US%3Aofficial&hs=uHu&q=java+read+data+from+usb+port&btnG=Search&meta=&aq=f&oq=]
What research did you do of your own? Have you done some testing application and tried yourself??

Just reinstalled software and migrated data from Time Machine, now iMac does not recognize printer or camera

Under the direction of Apple Support, I recently erased my iMac (Intel) hard drive, reinstalled and updated software and migrated data from an external hard drive via Time Machine.
Now, after clicking on "PRINT", the print dialog box says "printing" then says "no pages found", and finally says "stopped"; and when I plug in my camera to download photos, the camera is not recognized. Both printer and camera are connected via USB.
I checked connections, verified printing and iPhoto preferences, turned printer off then on again, unplugged and replugged USB connections, and checked and followed directions in the Help menu.

Thanks very much, I'd just tried rkaufmann87's suggestion and entered "This solved my question" when your suggestion popped up—you deserve a "This solved my question" too, though I saw only an option for "This helped me".
Before I got rkaufmann87's suggestion, I repaired disk permissions and that resolved the camera problem. Both of you nailed the solution.
Thanks again!

Problem while reading data from USB with JSR80

Hi
Iam using Fedora 9 with 32 bit.
Iam using JSR80 api to read the data from USB devices.
I successfully set-up the code as per given on JSR80 site on my eclipsce ide.
below is my code which iam using to read data from usb
import com.ibm.jusb.*;
import java.util.List;
import javax.usb.*;
import java.util.List;
public class USBReader {
public static UsbInterface interf = null;
     public static void main(String[] args) {
          try
        {// Access the system USB services, and access to the root
         // hub. Then traverse through the root hub.
           System.out.println("Application started");
         UsbServices services = UsbHostManager.getUsbServices();
         UsbHub rootHub = services.getRootUsbHub();
         traverse(rootHub);
         testIO(rootHub);
        } catch (Exception e) {
             System.out.println("The Exception occured"+e.getMessage());
      public static void traverse(UsbDevice device){
           System.out.println("Iam in traverse ");
           if (device.isUsbHub()){
                // This is a USB Hub, traverse through the hub.
                System.out.println("The device is hub");
                List attachedDevices = ((UsbHub) device).getAttachedUsbDevices();
                System.out.println("The attached devices size:"+attachedDevices.size());
                for (int i=0; i<attachedDevices.size(); i++){
                     traverse((UsbDevice) attachedDevices.get(i));
                if(attachedDevices !=null){
                     for(int j=0;j<attachedDevices.size();j++){
                          System.out.println("The device is"+attachedDevices.get(j));
       else{
          // This is a USB function, not a hub.
          // Do something.
            System.out.println("The device is not hub");
      public static void testIO(UsbDevice device) throws UsbClaimException, UsbNotActiveException, UsbDisconnectedException, UsbException{
           System.out.println("Iam in testIO");
          try{
             // Access to the active configuration of the USB device, obtain
             // all the interfaces available in that configuration.
             UsbConfiguration config = device.getActiveUsbConfiguration();
             List totalInterfaces = config.getUsbInterfaces();
             System.out.println("The Total interfaces: "+totalInterfaces.size());
             // Traverse through all the interfaces, and access the endpoints
             // available to that interface for I/O.
             for (int i=0; i<totalInterfaces.size(); i++){
                interf = (UsbInterface) totalInterfaces.get(i);
                System.out.println("The interfaces are "+totalInterfaces.get(i));
                String strinf=interf.getInterfaceString();
                System.out.println("Claimed Status: "+interf.isClaimed());
                System.out.println("Active status : "+interf.isActive());
                System.out.println("Settings :"+interf.getNumSettings());
                //interf.release();
                interf.claim();
                List totalEndpoints = interf.getUsbEndpoints();
                for (int j=0; j<totalEndpoints.size(); j++){
                   // Access the particular endpoint, determine the direction
                   // of its data flow, and type of data transfer, and open the
                   // data pipe for I/O.
                   UsbEndpoint ep = (UsbEndpoint) totalEndpoints.get(i);
                   int direction = ep.getDirection();
                   int type = ep.getType();
                   UsbPipe pipe = ep.getUsbPipe();
                   pipe.open();
                   // Perform I/O through the USB pipe here.
                   pipe.close();
                interf.release();
          } catch (Exception e) {
               System.out.println("Exception in TestIO"+e.getMessage());
               e.printStackTrace();
}When i execute the above code i get the following exception
Exception in TestIOCannot claim an interface on a virtual root hub.
javax.usb.UsbException: Cannot claim an interface on a virtual root hub.
     at com.ibm.jusb.VirtualRootUsbHubImp$VirtualRootUsbInterfaceOsImp.claim(VirtualRootUsbHubImp.java:143)
     at com.ibm.jusb.os.DefaultUsbInterfaceOsImp.claim(DefaultUsbInterfaceOsImp.java:54)
     at com.ibm.jusb.UsbInterfaceImp.claim(UsbInterfaceImp.java:109)
     at com.ibm.jusb.UsbInterfaceImp.claim(UsbInterfaceImp.java:83)
     at USBReader.testIO(USBReader.java:60)
     at USBReader.main(USBReader.java:15)iam not getting the clue for it .

Cannot claim an interface on a virtual root hubSo don't do that? I have no idea how to tell, but clearly you need to test a few more attributes before you claim. Or else just log the claim error and continue with the next interface.

Help me, How to read data from USB ???

Help me, How to read data from USB ???

If its a disk on key or some portable hard drive than once its connected to the usb and recognized by the system you can access it through java like you would access your hard drive.

Best way to control and read data from multiple instruments?

Hello,
I'm building an application to test power supplies involving multiple pieces of equipment over a couple of different comm busses. The application will also send control instructions to some of the instruments, and read data from some of the instruments. The reading and control profiles will not run on the same schedule (variable length control steps, configurable read interval).
I was thinking of using a queued statemachine (producer/consumer) for the control profile and another to read the data, but I got concerned that there would be collisions between sending control commands and read commands to the same machine. Is there a suggested design pattern for implementing something like this?
Timing of the commands isn't critical down to the milisecond, but I need to collect reasonably accurate timestamps when the data is read. The same is true for the control commands.
Here are the instruments I'm going to use, if the are control, read, or both, and the communication method
Instrument Funtions Comm Method
Power Supply Read data Communicates to PMBus Adapter
PMBus to USB Adapter Read data USB (Non-Visa)
Switch control relays USB (VISA)
Power Dist. Unit read data/control outlets SNMP (Ethernet)
Electronic Load read data/control load GPIB (VISA)
Thermal Chamber read data/control temp Ethernet (VISA)
Thanks,
Simon

Hello, there is a template in LV called "Continuous measurement and Logging".
It can give you some idea how to properly decouple the "GUI Event handler" top loop (where your Event structure is) from the DAQ and other loops.
You do not need to totally replicate the above example, but you can find there nice tricks which can help you at certain points.
The second loop from the top is the "UI message loop". It handles the commands coming from the top loop, and regarding to the local state machine and other possible conditions and states, it can command the other loops below.
During normal run, the different instrument loops just do the data reading, but if you send a control command from the top loop to a certain instrument loop (use a separate Queue for every instrument loops), that loop will Dequeue the control command, execute it, and goes back to data reading mode (in data reading mode the loop Dequeu itself with a "data read" command automatically). In this way the control and data read modes happen in serial not in parallel which you want to avoid (but I think some instrument drivers can even handle parallel access, it will not happen in really parallel...).
In every instrument loop when you read a value, attach a TimeStamp to it, and send this timestamp/value couple to the DataLogging loop via a Queue. You can use a cluster including 3 items: Source(instrument)/timestamp/value. All the instrument loops can use the same "Data logging" Queue. In the Datalogging while loop, after Dequeue-ing, you can Unbundle the cluster and save the timestamp and data-value into the required channel (different channel for every instrument) of a TDMS file.
(Important: NEVER use 2 Event structures in the same top level "main" VI!)

Acquire/manipulate audio data from internet stream

I want to acquire the audio data from an audio stream (i.e. pandora, youtube, etc.) from the internet. If I can get this data and be able to play it/graph it/etc in Labview, I will be pleased. However, I'm not sure if this is even possible not knowing the details behind how packets are built and transmitted over the internet.
The closest I've come is using the acquire_sound.vi and taking the data from the sound card; albeit, it's very noisy.
For fun though, I'd like to do something directly from the audio stream itself (perhaps building a dll?) to gain a better understanding and experience.
Any advice is greatly appreciated!

Dnor -
As far as I am aware there is a specific data time for audio streaming online, and it's something specific you would likely need to know on a low level to communicate/copy to. Although it wouldn't be real-time, you can run a Windows audio recording program like TotalRecorder which should save and convert the audio output to .wav. Then run a LabVIEW vi to read the wave file, which you could graph. There is a KnowledgeBase on setting up the read from .wav file here if you'd like to go that route: http://digital.ni.com/public.nsf/allkb/1BE60DBBFA22ACC186256DFB000B8464.
Regards,
Ben N.
Applications Engineering
ni.com/support

Task Sequence failed to restore captured data from USB drive onto a new machine using UDI task requence

Hi,
Environment ConfigMgr 2012 R2
Replace Scenario: Capture data to a USB external drive and Restore it from USB external drive.
Steps taken:
1) Created Computer Association with New computer and Source computer
2) Deployed UDI replace Task Sequence to Source computer and captured data to a USB external drive
3) Run UDI Task Sequence from Boot Media to Restore data from USB External drive which had the captured data.
Issue:
My task sequence failed to restore data from USB external drive.
Is there a fix
Any help is greatly appreciated it.

I created a query to see the deployment logs in real time. I see the TS fails when running "Request State Store" task. Here are the logs.
Severity Type Site code Date / Time System Component Message ID Description
Error Milestone POK 7/22/2014 4:13:15 PM MININT-P6E4T6G Task Sequence Engine 11141 The task sequence execution engine failed execution of a task sequence. The operating system reported error 1: Incorrect function.
Error Milestone POK 7/22/2014 4:13:15 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Error in the task sequence) in the group (Gather Logs and StateStore on Failure)
with the error code 1 Action output: [ smsswd.exe ] PackageID = '' BaseVar = '', ContinueOnError='' ProgramName = 'cscript "C:\_SMSTaskSequence\WDPackage\scripts\ztierrormsg.wsf"' SwdAction = '0001' Set command line: Run command line Working dir 'not
set' Executing command line: Run command line Process completed with exit code 1 Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Microsoft Deployment Toolkit version: 6.2.5019.0 The task sequencer
log is located at C:\WINDOWS\CCM\Logs\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log. ZTI deployment failed, Return Code = 1 Command line returned 1. The operating system reported error 1: Incorrect function.
Information Milestone POK 7/22/2014 4:13:14 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Copy Logs) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: ... 扴捡杫潲湵⹤潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就瑺獩瑥慢正牧畯摮氮杯潃祰湩⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯穜楴慴潴⹯潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散�潌獧䍜剏ⵐ䠳䑗塐就潃祰湩⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯作䑓敓畴坰穩牡⹤潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就协卄瑥灵楗慺摲氮杯潃祰湩⁧㩃坜义佄南停湡桴�潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就慐瑮敨屲湕瑡整摮䍇潃祰湩⁧潬⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯䉜䑄氮杯挠湯整瑮⁳潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌�Console
> Successfully resized the shadow copy storage association Return code from command = 0 Cleaning up default wallpaper registry keys Process completed with exit code 0 zticopylogs processing completed successfully. Command line returned 0.
Information Milestone POK 7/22/2014 4:13:07 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Move State Store) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: [ smsswd.exe ] PackageID = '' BaseVar = '', ContinueOnError='' ProgramName = 'cscript.exe "C:\_SMSTaskSequence\WDPackage\scripts\ztimovestatestore.wsf"' SwdAction = '0001' Command line for extension .exe is "%1" %* Set
command line: Run command lineWorking dir 'not set' Executing command line: Run command line Process completed with exit code 0 Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Microsoft Deployment
Toolkit version: 6.2.5019.0 The task sequencer log is located at C:\WINDOWS\CCM\Logs\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log. ztimovestatestore processing completed successfully. Command line returned 0.
Information Milestone POK 7/22/2014 4:13:07 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Gather) in the group (Gather Logs and StateStore on Failure) with
exit code 0 Action output: ... (BIOS is 'DELL - 1072009'). Property IsVM is now = False Finished getting virtualization info Connection succeeded to MicrosoftVolumeEncryption There are no encrypted drives Property IsBDE is now = False Processing
the phase. Determining theINI file to use. Using COMMAND LINE ARG: Ini file = CustomSettings.ini Finished determining the INI file to use. Added new custom property MYCUSTOMPROPERTY Using from [Settings]: Rule Priority = DEFAULT ------ Processing the
[DEFAULT] section ------Process completed with exit code 0 ------ Done processing CustomSettings.ini ------ Remapping variables. Property TaskSequenceID is now = Property DeploymentType is now = NEWCOMPUTER Finished remapping variables. ZTIGather processing
completed successfully. Command line returned 0 ReleaseSource() for C:\_SMSTaskSequence\Packages\POK0000F. reference count 1 for the source C:\_SMSTaskSequence\Packages\POK0000F before releasing Released the resolved source C:\_SMSTaskSequence\Packages\POK0000F.
Information Milestone POK 7/22/2014 4:13:03 PM MININT-P6E4T6G Task Sequence Engine 11130 The task sequence execution engine skipped the action (Use Toolkit Package) in the group (Gather Logs and StateStore on Failure) because
the condition was evaluated to be false.
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Set Error Code) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: Finished with error code 0.
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11124 The task sequence execution engine started the group (Gather Logs and StateStore on Failure).
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11122 The task sequence execution engine skipped the group (Cancelled Wizard Group) because the condition was evaluated to be false.
Error Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Connect to State Store) in the group (State Restore) with the error code 1
Action output: ... ( 0x80070035 ) , trying to connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 15 seconds. Unable to connect to share: The network path was notfound. ( 0x80070035 ) , trying to
connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 20 seconds. Unable to connect to share: The network path wasnot found. ( 0x80070035 ) , trying to
connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 25 seconds. Process completed with exit code 1 ERROR - Unable to map a network drive to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Unable to connect to 563807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f ZTI ERROR - Non-zero return code by ZTIConnect,
rc = 1 Command line returned 1. The operating system reported error 1: Incorrect function.
Warning Milestone POK 7/22/2014 4:11:46 PM MININT-P6E4T6G Task Sequence Engine 11138 The task sequence execution engine ignored execution failure of the action (Request State Store) in the group (State Restore).
Error Milestone POK 7/22/2014 4:11:46 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Request State Store) in the group (State Restore) with the error code 16389
Action output: ... etting Media Certificate. Sending request to MP
http://abcdefg.xyx.xyz.local. Setting message signatures. Setting the authenticator. CLibSMSMessageWinHttpTransport::Send: URL: abcdefg.xyx.xyz.local:80 CCM_POST /ccm_system/requestRequest was successful. migInfoRequestMessage.DoRequest (m_sResponse,true),
HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,1098) pClientRequestToMP->DoRequest(), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2778) ExecuteRestoreRequestToMP(migInfoFromMP),
HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2903) ExecuteRestoreRequest(), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\main.cpp,84) OSDSMPClient finished: 0x00004005 reply from server
is 'NoReply' ClientRequestToMP::DoRequest failed (0x80004005). ExecuteRestoreRequestToMP failed (0x80004005). ExecuteRestoreRequest failed (0x80004005).. The operating system reported error 1: Incorrect function.

ADF 11g can not select and copy data from cell of readonly table in IE

hi,
In ADF 11g, when render view object as readonly table with Single RowsSelection, using IE browser can not select and copy data from the cell, but it work in firefox.
is it a bug?
Edited by: kent2066 on 2009-5-18 上午8:46

Hi Timo,
Sorry forgot to mention versions.
We are using 11.1.1.7 and IE 9.
I tried in Google but could not get the solution.
Kindly let me know solution for this.
PavanKumar

Acquiring and plotting data from USB raw

Similar Messages

Maybe you are looking for