Acs 5.4.46 filter using client IP address

Hello,
Is there a way to filter RADIUS network access using client station IP?
Thanks,

Hi Jatin,
Thank you for your replay.
The calling station-id didn't worked, only the framed-ip-address.
But in framed-ip-address i can't use a subnet.
Is there anyway to use framed-ip-address wth a subnet?

Similar Messages

Deny Mac address cannot use client ip address

Dear Team
How I can restrict Mac address in the denied list ,cannot use ip address.
Regards
Njsingh

Hi,
If you want to filter DHCP client by MAC address in order to prevent some device from obtaining IP address. You may enable Deny Filters on DHCP console first, and then New Filter by MAC address. Detailed steps you may reference the link below:
http://technet.microsoft.com/en-us/library/dd759190.aspx
Windows Server 2008 R2 or above system version has this function. Reference:
http://blogs.technet.com/b/teamdhcp/archive/2009/02/26/new-features-in-dhcp-for-windows-server-2008-r2-windows-7.aspx
If there is any misunderstanding about your question, please correct.
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

I am automating the process of sending appointment reminders to my clients. I started with an alert with an email in calendar using the clients email address as a custom entry in my me card in my contacts. this was resulting in three emails being sent wit

I am automating the process of sending appointment reminders to my clients. I started with an alert with an email in calendar using the clients email address as a custom entry in my me card in my contacts. this was resulting in three emails being sent with slightly different versions of the same address (see my previous post). Heating someone else's suggestion I created a workflow file to send an email and calling that file from an alert on my calendar. This is working and sends only one email to the client.
My calendar is on I cloud and I access it from three different computers so I can keep my appointment calendar current. The files that send the email only exist on one computer. My other computers show error messages when those emails get sent. It seems that each computer wants to send the email. It's a small problem but is there a way that I could not get those alerts.
But appreciate any thoughts about this. It seems like both problems might be related to the iCloud system.
Thank you in advance,
Michael

Good work, catch so far Michael, does seem to be a "feature" of iCloud syncing, not sure what you could do to disable it.

How to copy a page( webpart page) with its content using client side.

How to copy a page(in my case webpart page) with its content(it may contain webparts) using client code (i mean using SPservices or ECMA script).
What i am planning is ,to give end user a page where it will contain text box to specify name of page and a button with the help of content editor webpart.
where on click of button we need to write client side code such that it should create a new page from a existing page in a library with given name by user.
Any suggestion would be helpful. For your information we can do it through UI with the help Site Actions / Manage Content and Structure.But i want to automate it using client side code.Server side code is restricted.
or can we create a template of an existing page with content without the help of sharepoint designer.
Thanks in advance
with regards Ravichandra

This is good example
http://balajiindia.wordpress.com/2011/05/27/using-jquery-with-custom-web-services-in-sharepoint/
Create web service
http://balajiindia.wordpress.com/2011/05/27/using-jquery-with-custom-web-services-in-sharepoint/. Create method "Create Page" http://www.learningsharepoint.com/2010/09/17/create-publishing-pages-sharepoint-2010-programmatically/
Build your Java Script. You can use Content Editor Web Part if you want to avoid custom web part development http://www.codeproject.com/Articles/544538/JQuery-with-SharePoint
Oleg

Unable to get the SharePoint 2013 List names using Client object model for the input URL

Please can you help with this issue.
We are not able to get the SharePoint 2013 List names using Client object model for the input URL.
What we need is to use default credentials to authenticate user to get only those list which he has access to.
clientContext.Credentials = Net.CredentialCache.DefaultCredentials
But in this case we are getting error saying ‘The remote server returned an error: (401) Unauthorized.’
Instead of passing Default Credentials, if we pass the User credentials using:
clientContext.Credentials = New Net.NetworkCredential("Administrator", "password", "contoso")
It authenticates the user and works fine. Since we are developing a web part, it would not be possible to pass the user credentials. Also, the sample source code works perfectly fine on the SharePoint 2010 environment. We need to get the same functionality
working for SharePoint 2013.
We are also facing the same issue while authenticating PSI(Project Server Interface) Web services for Project Server 2013.
Can you please let us know how we can overcome the above issue? Please let us know if you need any further information from our end on the same.
Sample code is here: http://www.projectsolution.com/Data/Support/MS/SharePointTestApplication.zip
Regards, PJ Mistry (Email: [email protected] | Web: http://www.projectsolution.co.uk | Blog: EPMGuy.com)

Hi Mistry,
I sure that CSOM will authenticate without passing the
"clientContext.Credentials = Net.CredentialCache.DefaultCredentials" by default. It will take the current login user credentials by default. For more details about the CSOM operations refer the below link.
http://msdn.microsoft.com/en-us/library/office/fp179912.aspx
-- Vadivelu B Life with SharePoint

How to get list of users who all are having full access in sharepoint site using client object model c#

Hi,
I want to fetch the list of users who all are having full access to the sharepoint list using client object model with .Net
Please let me know if any property for the user object or any other way to get it.
Thanks in advance.

Here you are complete code i created from some years it lists all groups and users, you can just add a check in the permissions loop to see if it is equal to Full Control.
Private void GetData(object obj)
MyArgs args = obj as MyArgs;
try
if (args == null)
return; // called without parameters or invalid type
using (ClientContext clientContext = new ClientContext(args.URL))
// clientContext.AuthenticationMode = ClientAuthenticationMode.;
NetworkCredential credentials = new NetworkCredential(args.UserName, args.Password, args.Domain);
clientContext.Credentials = credentials;
RoleAssignmentCollection roles = clientContext.Web.RoleAssignments;
ListViewItem lvi;
ListViewItem.ListViewSubItem lvsi;
ListViewItem lvigroup;
ListViewItem.ListViewSubItem lvsigroup;
clientContext.Load(roles);
clientContext.ExecuteQuery();
foreach (RoleAssignment orole in roles)
clientContext.Load(orole.Member);
clientContext.ExecuteQuery();
//name
//MessageBox.Show(orole.Member.LoginName);
lvi = new ListViewItem();
lvi.Text = orole.Member.LoginName;
lvsi = new ListViewItem.ListViewSubItem();
lvsi.Text = orole.Member.PrincipalType.ToString();
lvi.SubItems.Add(lvsi);
//get the type group or user
// MessageBox.Show(orole.Member.PrincipalType.ToString());
if (orole.Member.PrincipalType.ToString() == "SharePointGroup")
lvigroup = new ListViewItem();
lvigroup.Text = orole.Member.LoginName;
// args.GroupsList.Items.Add(lvigroup);
DoUpdate1(lvigroup);
Group group = clientContext.Web.SiteGroups.GetById(orole.Member.Id);
UserCollection collUser = group.Users;
clientContext.Load(collUser);
clientContext.ExecuteQuery();
foreach (User oUser in collUser)
lvigroup = new ListViewItem();
lvigroup.Text = "";
lvsigroup = new ListViewItem.ListViewSubItem();
lvsigroup.Text = oUser.LoginName;
lvigroup.SubItems.Add(lvsigroup);
//args.GroupsList.Items.Add(lvigroup);
DoUpdate1(lvigroup);
// MessageBox.Show(oUser.LoginName);
RoleDefinitionBindingCollection roleDefsbindings = null;
roleDefsbindings = orole.RoleDefinitionBindings;
clientContext.Load(roleDefsbindings);
clientContext.ExecuteQuery();
//permission level
lvsi = new ListViewItem.ListViewSubItem();
string permissionsstr = string.Empty;
for (int i = 0; i < roleDefsbindings.Count; i++)
if (i == roleDefsbindings.Count - 1)
permissionsstr = permissionsstr += roleDefsbindings[i].Name;
else
permissionsstr = permissionsstr += roleDefsbindings[i].Name + ", ";
lvsi.Text = permissionsstr;
lvi.SubItems.Add(lvsi);
// args.PermissionsList.Items.Add(lvi);
DoUpdate2(lvi);
catch (Exception ex)
MessageBox.Show(ex.Message);
finally
DoUpdate3();
Kind Regards, John Naguib Technical Consultant/Architect MCITP, MCPD, MCTS, MCT, TOGAF 9 Foundation

How do I get list of client IP Addresses using new Airport Utility v6.3?

I have purchased and Airport Time Capsule 3TB (newest model). Previous models were still compatible with Airport Utility 5.6 and I could use "manual" mode to get a list of client IP addresses attached to the device. The new Airport Time Capsule is only compatible with Airport Utility 6.3 and I cannot figure out how to get a list of client IP addresses with this new model. Does anyone know how to do this?

Try a ping broadcast - for example if your network were 192.168.1.xxx (netmask of 255.255.255.0) try this from a Termnal.app window (located in /Applications/Utilities):
ping 192.168.1.255
If you have a different type netmask, you need to put 255's where the 0's are in your netmask.
Everyone on the local network (the 192.168.1.xxx network) should reply that is up and running unless you have them setup to not respond to pings (the WAN port on your TC should not reply cause it's in a different network) and you have your list of clients on the network. If you setup the TC to dedicate a range of addresses for WiFi clients you can even identify which of them are wired and which are wireless.
good luck.

To extract the users permission on files and folders in sharepoint 2010 using client object model

To extract the users permission on files and folders in sharepoint 2010 using client object model

Hello,
This is sample code to get item level permisison: (Just written in notepad so it is not tested)
public void ItemLevelPermission()
SecurableObject curObj = null;
ListItem curItem = ctx.Web.Lists.GetByTitle("LibraryName").GetItemById(ItemId); -> Use Id of file or folder.
IEnumerable roles = null;
roles = ctx.LoadQuery(
curObj.RoleAssignments.Include(
roleAsg => roleAsg.Member,
roleAsg => roleAsg.RoleDefinitionBindings.Include(
roleDef => roleDef.Name, // for each role definition, include roleDef’s Name
roleDef => roleDef.Description)));
ctx.ExecuteQuery();
Hope it could help
Hemendra:Yesterday is just a memory,Tomorrow we may never see
Please remember to mark the replies as answers if they help and unmark them if they provide no help

Setting the default value to taxonomy column in sharepoint 2010 using client object model

I am creating a metadata column and I want to set its default value in sharepoint 2010 using client object model. Can anyone help me?
My code for creating metadata column is as below:
            ClientContext clientContext = new ClientContext(siteUrl);
            Web site = clientContext.Web;
            List list = site.Lists.GetByTitle("LibraryName");
            FieldCollection collField = list.Fields;
            string fieldSchema = "<Field Type='TaxonomyFieldType' DisplayName='SoftwareColumn' Name='SoftwareColumn' />";
            collField.AddFieldAsXml(fieldSchema, true, AddFieldOptions.DefaultValue);
            //oneField.DefaultValue = "ASP.NET|4c984b91-b308-4884-b1f1-aee5d7ed58b2"; // wssId[0].ToString() + ";#" + term.Name + "|" + term.Id.ToString().ToLower();
            clientContext.Load(collField);
            clientContext.ExecuteQuery();

Hi,
Please try the code like this:
ClientContext clientContext = new ClientContext("http://yoursite/");
List list = clientContext.Web.Lists.GetByTitle("List1_mmsfield");
clientContext.Load(list);
clientContext.ExecuteQuery();
FieldCollection fields = list.Fields;
clientContext.Load(fields);
clientContext.ExecuteQuery();
Field f = fields.GetByTitle("mms");
clientContext.Load(f);
clientContext.ExecuteQuery();
Console.WriteLine(f.Title + "---" + f.DefaultValue);
//2;#A2|a0a95267-b758-4e4d-8c39-067069fd2eef
//1;#A1|641f5726-992c-41c8-9ddc-204a60b88584
f.DefaultValue = "1;#A1|641f5726-992c-41c8-9ddc-204a60b88584";
f.Update();
clientContext.Load(f);
clientContext.ExecuteQuery();
Console.WriteLine(f.Title + "---" + f.DefaultValue);
Best regards
Patrick Liang
TechNet Community Support

How to activate Custom Feature in SharePoint 2010 using Client Object model

I am trying to Activate a custom feature using Client Object Model in SharePoint 2010. Here is the code I used. When I execute the code, I got the error "Feature with Id 'xx' is not installed in this farm, and cannot be added to this scope while
creating site collection". Can anyone help?
ClientContext clientContext = new ClientContext(spURL);
//GUID of the custom feature
Guid districtFeatureId = new Guid("5b3529de-5045-46da-af87-8d2e32c121a7");
Site clientSite = clientContext.Site;
FeatureCollection clientSiteFeatures = clientSite.Features;
clientContext.Load(clientSiteFeatures);
clientContext.ExecuteQuery();
//Activate the feature
clientSiteFeatures.Add(districtFeatureId, false, FeatureDefinitionScope.Site);
clientContext.ExecuteQuery();

Hi shil chan,
When you activate a feature on the site collection, the feature should be scoped to site or farm, the error message shows it cannot find the specific feature, this will happen when you have a feature in web
scope or the feature isn’t installed.
So, to troubleshooting this issue:
Verify whether the feature is scoped to web. Please go to
Site Setting->Site Features . If the feature is a web scope feature, then add the feature to webfeatures.
Make sure the feature is installed correctly.
Please inform me freely if you have any questions.
Thanks

How to use CLIENT-CERT authentication?

Hi,
I would like to know how to use client authentication.
I used a web application with CLIENT-CERT authentication.
And I accessed to the application from browser, then I had the following error
message:
Incorrect or missing client certificate.
I used OpenSSL to generate keys.
Could you tell me the information of the setting?
Especially, I don't know theentry of CertAuthenticator.
Could you tell me?
Regards,
Kuniaki Hagiwara - HP Japan

Thank you for your response.
Yes we have added the client certificate file (.pfx) in the Firefox browser Certificate manager / Store. It's also showing the certificate in the View Certificate window. We could not resolve it yet.

How to Enable Ratings on SharePoint List using Client Object Model for Office 365 SharePoint Site.

How to Enable Ratings on SharePoint List using Client Object Model code for Office 365 SharePoint Site.
Thanks in Advance
Rajendra K

Hi Rajendra,
here you are the code and the blog, let me know if this helps
using (ClientContext ctx = new ClientContext(https://yourSiteUrl))
Web w = ctx.Web;
List l = w.Lists.GetByTitle("yourListName");
ctx.Load(l, info => info.Id);
ctx.ExecuteQuery();
string ListID = l.Id.ToString();
Microsoft.Office.Server.ReputationModel.Reputation.SetRating(ctx, ListID, 1, 5);
ctx.ExecuteQuery();
http://blogs.technet.com/b/speschka/archive/2013/07/08/how-to-use-csom-with-ratings-in-sharepoint-2013.aspx
Kind Regards, John Naguib Technical Consultant/Architect MCITP, MCPD, MCTS, MCT, TOGAF 9 Foundation

How to use FILTER -- USING in rpd???

Can we use FILTER USING in rpd ?

Yes in the 'use existing logical columns as the source' window of a measure.
Its under Functions - Display Functions in the expression builder.

Not able to use Client Object Model in Visual Webpart SandBox Solution?

Hi,
I am trying to use client object model in visual webpart in sandbox solution but i am getting unexpected error but if i remove client object model code webpart works fine?
any help is appreciated.
Regards,
Gaurav Verma

Check this article for your answer
How to leverage the Client Object Model in a Sandbox Visual Web Part
Mark ANSWER if this reply resolves your query, If helpful then VOTE HELPFUL
INSQLSERVER.COM
Mohammad Nizamuddin

Interactive Report filter using "in"

I am using an interactive report, and I want to filter using the "in" criteria. The data I want to filter is a person's name, and it is a concatenation of the entire name, last name first. I have no problem doing this filter on just the first or last name, but the concatenated field has a comma in it, and that seems to be throwing the filter off.
What automatically populates when I click a name from the list is something like:
Abraham, Adam
I can see that it would probably be interpreting that as two different values. But even if I put single or double quotes around the name, it still does not work correctly.
An example available at:
http://apex.oracle.com/pls/otn/f?p=41923:1
Try doing an "in" filter on the "name" column.
Thanks,
David

David,
The comma is the operational separator for the 'IN' clause, so you are right, the filter sees each part of the name as a parameter. Just use something else as the separator (like a space) and you will be good to go.
Keep Smiling,
Bob R

Acs 5.4.46 filter using client IP address

Similar Messages

Maybe you are looking for