Adding a Custom VSA to a Group - ACS Appliance

Hi,
Using a secure ACS Appliance 4.0
I want to add a new RADIUS Vendor and its associated VSA to the ACS configuration. This will then be returned during Authorization.
I have already added the new Vendor and the required VSA through RDBMS. I can now see the new vendor as RADIUS (vendor) in NAP Profile etc
However I cannot seem to find a way that how would i set the Value of the Added VSA ? And assign it to a particular group ? I cannot seem to find that VSA anywhere.

Add a AAA client with "Authenticate using" Radius(vendor)
then go to Interface Configuration and enable VSA for Group/User
~Rohit

Similar Messages

No attribute appear in new custom VSA RADIUS

Hi,
I use Cisco Secure version 3.2 on windows 2000
I just had a new custom VSA Radius with the utility CSUtil.exe
Fist i create the file myvsa.ini, this is for a SONET optical Nortel equipement, here it is:
[User Defined Vendor]
Name=OM3000
IETF Code=562
VSA 1=OM3000_UPC
[OM3000_UPC]
Type=INTEGER
Profile=OUT
Enums=Levels_Privileges
[Levels_Privileges]
0=UPC0
1=UPC1
2=UPC2
3=UPC3
4=UPC4
5=UPC5
After i check if i have a UDV unassigned
C:\Program Files\CiscoSecure ACS v3.2\Utils>csutil -listudv
Here the response:
UDV 0 - Unassigned
UDV 1 - Unassigned
UDV 2 - Unassigned
UDV 3 - Unassigned
UDV 4 - Unassigned
UDV 5 - Unassigned
UDV 6 - Unassigned
UDV 7 - Unassigned
UDV 8 - Unassigned
UDV 9 - Unassigned
Then i run the command: C:\Program Files\CiscoSecure ACS v3.2\Utils>csutil -addudv 0 c:\temp\myvsa.ini
I get the following messages
Adding or removing vendors requires ACS services to be re-started.
Please make sure regedit is not running as it can prevent registry
backup/restore operations
Are you sure you want to proceed? (y/n)y
Parsing [c:\temp\myvsa.ini] for addition at UDV slot [0]
Stopping any running services
Creating backup of current config
Adding Vendor [OM3000] added as [RADIUS (OM3000)]
Adding VSA [OM3000_UPC]
Done
Checking new configuration...
New configuration OK
Re-starting stopped services
Verify that OM3000 was added.
C:\Program Files\CiscoSecure ACS v3.2\Utils>csutil -listudv
UDV 0 - RADIUS (OM3000)
UDV 1 - Unassigned
UDV 2 - Unassigned
UDV 3 - Unassigned
UDV 4 - Unassigned
UDV 5 - Unassigned
UDV 6 - Unassigned
UDV 7 - Unassigned
UDV 8 - Unassigned
UDV 9 - Unassigned
Return to ACS Admin and select Interface configuration and enable RADIUS(OM3000) for group.
The problem is, i do not see any attribute under the Title RADIUS(OM3000)
I expect to see the attribute OM3000 and a drop down list option with the integer 0 to 5 to select but nothing
Do i miss something or it is a ACS known bug ?????
It is the same under a group in the section GROUP SETUP , i see the section RADIUS(IETF) with attributes in this section that can be seclect and configure..
But under the section RADIUS(OM3000) there is no attribute, this section is empty ????
Thanks in advance for your help
Dan

I've imported the UDV file that you listed in your original post into a test ACS server that I have. The version that I am running is ACS v3.3(1) and when I go in and edit a user/group, I all see the "RADIUS (OM3000) Attributes" section at the bottom of the setup page. Within that box, I have an option for "[562\001] OM3000_UPC" with a dropdown box to the right of it with values of "UPC0" through "UPC5".
Seeing this work in 3.3(1) makes me wonder if there might be a bug within the version of ACS that you are using. I may have version 3.2 installed on a test system yet. I will take a look and try importing this into that one and see what results I get.
Steve

Adding new custom field in already existing custom tab for MM01

Hello Guru,
I have a requirement that add a custom field in already existing custom view of MM01. I did the following steps :
1. I have cerated a new field in MARA using APPEND structure.
2. I have found the function group(Y_FE_MARA) that already there other subscreens, so that I have added another subscreen in that function group and created a field from MARA in the screen.
3. in SPRO went for the path Logistics General->Material Master->Configuring the Material->Define Structure of Data screens for Each Screen sequence
In the 3rd step, I have choosen already existing screen sequence(Y1) and went for Data Screens and choosen for Custom tab and double click on subscreens and then I have added the program as SAPLY_FE_MARA and subscreen number(011) and saved it.
After all the above steps, I have run MM02/MM03 then the field is not getting displayed in the screen of custom view.
Did I miss any steps here? Please suggest me if I did something wrong.
Thanks and Regards,
Muralikrishna Peravali

Hi Raymond,
Thank you for the reply. As per the note some one already implemented the Screen Enhancement with 2 custom views. I need to add the field in any one of existing custom view. So for this I have created a Subscreen in copied function group of MGD1(Y_FE_MARA). But in the function group already 10 Subscreens were created. Is this is the problem? or else copy the FG MGD1 into another FG and create the subscreen will be feasible to my scenario?
Please suggest me.
Thanks and Regards,
Muralikrishna Peravali

Error while adding a custom field with Input help via AET

Hi All,
I need to add two custom field under Service orders at Item level in component BT140I_SRVP.
One field is required to have the input search help f4 and autopopulates the second field
I am able to add one field(not requiring help) successfully through AET .
I have created one Zsearch_help in se11 and its successfully running and Autopopulating seocnd field while I am testing it
While adding second field through AET,I need to enter following details as -
field label,search relevant ,serach help etc.
When I type the name of my 'Zsearch_help' against field search help it gives me following error
'Search help is not compatible'.
Secondly,not getting getter and setter methods for the attrributes in BTAdminI.
Last,please tell me if i create zhelp and activate it,would it automatically appear in the list on AETwhile assiging it to input field?
Please help me out.Kindly be detailed as I am new to SAP CRM.
Thanks,
Shivani

The question is answered in CRM 7.0 forum:
Getting error while adding a custom field (with input help) through AET

Grouping customers and view customer open items list - Group wise

Hi.
I have some requirement from my client.
He says that he want to view customer open items list group wise.
In FBL5N we can give the selection of multiple customers. But he wants to group the specific customers and then view the open items for this group.
For example: Client has 10 customers and out of these customers he wants to select and group 5 customers. And then he want to view open items list for this group.
Can anyone help me how to group these specific customers in the total customers list. Also request you to provide me the option to view open items for this group of customers.
Regards,
Padmavathi

Hi Padmavathi,
It is possible. use Worklist for Customers.
Go to OB55 and define a Worklist for Customers, and mention the list of Customers that you want to see under that Worklist.
After this, when you to to FBL5N, you will get an option to select Worklist to run the list of open items.. and it would show open items of all customers that you have defined in your worklist.
Also note that you will have to go to FB00, tab Line Items, and tick Worklists available. This is at User Level, so only that user will be able to see the worklist in his FBL5N transaction code.
Regards,
SAPFICO
Edited by: SAPFICO on Feb 10, 2011 11:43 AM

Adding a custom webpart to webpart page not a safe control issue

When I am adding a custom web part to web part page I am getting below error as a popup. Plz help if any body resolved the same issue.
Unable to add selected web part(s). (Web Part Name): A Web Part or Web Form Control on this Page cannot be displayed or imported.
The type could not be found or it is not registered as safe
Regards.
Avinash.
Avinash

Hi,
Here you go. This should help you.
ow many times have you guys faced an issue like this ?"The type could not be found or it is not registered as safe." .To resolve this, make sure that you add safe controls around your web part assembly in web.config.
<SafeControls>
< SafeControl Assembly=”WebPart, Version=1.0.0.0, Culture=neutral, PublicKeyToken=abcdeddf23232″ Namespace=”Mywebpart.WebPart” TypeName=”*” Safe=”True” />
< /SafeControls>
The above ensure that your web part code is secured and wont let any anonymous users to access the web part.
Happy SharePointing ;-)
http://www.c-sharpcorner.com/Blogs/15024/
Please remember to click 'Mark as Answer' on the answer if it helps you

I added a custom ringtone . Then later I tried to add another three set but now after sync . Am not able to get rid of the first one... It's still there as my custom ringtone. But my iPhone in iTunes shows all four... But the phone shows only one...?

I added a custom ringtone . Then later I tried to add another three set but now after sync . Am not able to get rid of the first one... It's still there as my custom ringtone. But my iPhone in iTunes shows all four... But the phone shows only one...?

Paul--you are a life-saver!! Worked great. I did have to look around to make sure I was getting 4.9 instead of 4.7 (even when the file was named 4.9 at techspot.com), but I finally got the right file, did the install as you suggested, and everything is now fine. One note, though, that I haven't seen mentioned in any of this thread: when I first tried to open up iTunes after getting back to 4.9, the following message appeared: "The file iTunes Library.itl cannot be read because it was created by a newer version of iTunes." I merely went to the old .itl file that was created when I did the update to iTunes 5, renamed it, moved it over to my now new 4.9, and iTunes opened fine. My library was a few days out of date, because of the few days' lag from the time I did the iTunes update, but that was easily taken care of, and everything's now working fine. Thanks again!!!

Multiple GL accounts for customer A/c assgmt group

Dear All,
I have assigned GL account(100) in VKOA to customer a/c assgmt group(DM).
Now i would like to add 2 more accounts(101, 102) to the same customer a/c assgmt group(DM).
Is it possible to do this? How?
Please help me in doing this.
Thanks in advance
Regards,
Pritam

Hi,
Thanks for reply!
Actually we have defined revenue accounts as per region for customers.
Say 100 for north region, 102 for south...like this.
My account key, material a/c group, sales org and chart of accounts will be same in this case.
How i do this?
Regards,
Pritam

Adding a custom field in standard search criteria in SAP SRM SLM

Hi Friends,
Currently we are using SAP SRM with SLM system .
In SLM system we have a functionality to replicate the supplier to other system ( like ECC SUS etc).
As per the requirement we have done some enhancement and now we need to enhance the standard search functionality by
adding our custom filed to one of the search parameter field
Kindly refer the screen shot
Click on Supplier Lifecycle Management -> Distribute Supplier
Kindly suggest the steps to implement this change.

Hi,
See this thread:
Vendor Master Extension in SRM
For custom fields for vendor master,you can use the BADI's BBP_GET_VMDATA_CF(In SRM) and BAdI BBP_MAP_VMDATA_CF (In R/3).
Other related links:
http://www.sapdevelopment.co.uk/enhance/bdt/bdthome.htm
http://help.sap.com/saphelp_erp2004/helpdata/en/2f/696d360856e808e10000009b38f839/content.htm
F4 for customer table fields
Look for the OSS Note for more details.
Note 675800 - Business partner enhancement SRM on maintenance screen
BR,
Deepti.

Regarding adding a Custom field to Standard Table

Hi ABAPers,
Can any one explain the below spec-description.
"The purpose of this design is to provide the foundation for a more automated solution to the invoice reconciliation process. This design calls for adding a custom field to the standard SAP table EINE as well as a data maintenance tool for the same. There will also be a new custom table for storing values associated with the new EINE field. These new tables will also provide users with the ability to determine which PIR are soon to expire."
We have to add one custom field to standard table EINE, how we can add this custom field to STND table.
According to me we can add it through append structure. is it correct or not.
and what is data maintenance tool.
Pls.............Explain in details.
Thanks in advance.
Regards,
Ramana Prasad. T

Hi,
Goto SE11 ,give ur table name.Then press display button.Then in the application tool bar press on append structure ...Now create a zstructure and add ur custom field and then activate the table.
Regards,
nagaraj

HR Custom InfoTypes problem when added to custom Infoset Report for PA

Hi, I am having an issue with the adhoc query /SAPQUERY/HR_ADM. I added the custom infotypes 9* I created to this standard infoset by using SQ02 and adding these by going into the menu path Edit--> Change InfoType selection. I regenerated this object and attached to a transport. The query runs fine in the DEV system where I made the change...I can choose fields for output or selection from the standard infotypes and custom infotypes as expected. I migrated this transport to the test system and now when I try to do the same thing I get an error when I try to click on any object in my custom infotype and some of the standard infotype. I tried regenerating and resending to the test system and still have the same issue. This is the error in the dump:
    79 * create work area
    80   create data data_wa like line of data_table.
    81   assign data_wa->* to <data_wa>.
    82   assign component fcat_wa-fieldname OF STRUCTURE <data_wa>
    83     to <field>.
    84
    85   loop at t_fcat into fcat_wa.
    86     field_filled = 'X'.
    87     assign component fcat_wa-fieldname OF STRUCTURE <data_wa>
    88     to <field>.
    89     if sy-subrc <> 0.
>>>>>       raise internal_error.
It appears the TEXT488 is the value in the fcat_wa-fieldname and I do not see this in the data_wa.
Does anyone know how to fix this problem or what I might try or look at to see what the difference is between the DEV system (where it works ok) the the Test system where it is giving me an error?
Thanks in advance for any help you can provide.
Laurie

After further investigation I found the problem to this was in the generation of the objects. Even though I generated before attaching to a transport and all looked ok, there is some sort of bug causing it to not generate properly so I had to sign on to each environment and generate the object in SQ02 including in Production. After I did this the custom infotypes were accessible in the Infoset.

Adding New Customer Address to an Existing one

Adding New Customer Address to an Existing one
Hi
We have a lot customers set up in Oracle and they only have a
ship to address and now we would like to add the bill to address
to these customers. Since there are a lot of customers I was
wondering is there is an open interface we can use to that.
Thank you
alpha

Hi Chandu,
1.In Infospoke -> General tab -> DataSouce(here infobject - 0BPARTNER).
2. Destination tab -> choose radio button(DB Table or Flat file).
3. Goto tab infoobjects -> select required fields you want to send from left to right.
4. Give the selection accordingly(here i think PATRNER). But it should be available in your datasouce(Infoobject-0BPARTNER), if you want to give selection on this. I didnt understad what you mean of <b>"hide"</b> in your previous reply. If this is not available in your infoobject(OBPARTNER), How CAN YOU GIVE SELECTION ON THIS attribute...?
5. Try to add this field in Infoobject(0BPARTNER) and populate.
6. Trnasformation tab.
Here you can see Source Structure, Target Structure and Addin implementation.
Source Structure - system will generate according to the field you selected in InfoObjects tab(You cant change it).
Target Structure - You can define your own structure if you want or you can modify the generated structure. By default system generates Target Structure same as Source structure(if you want to add any more fields you can add here, but you have to populate those fields with your own coding in BAdi), Which is Addin implementation.
Srini
Message was edited by: Srini

Custom Attributes in Target Group

Hi,
we are experiencing an issue during Target group creation: we are unable to see our custom attributes in the Target Group.
We have an Attribute List created by a Custom infoset; the Infoset is based on a custom Table.
When we create a profile Set from this Attribute list, the Target Group is created with the correct records number, but when we look at the Target Group we find there only standard attributes, that are not defined in our Attribute List (they seems all BUT000 fields).
How can we add our custom Field to Target Group Structure?
I've read someone suggests to enahnce CRM_IM_ADD_DATA_BADI BADI: this is the only possible option? there is a way to do it using SPRO transaction?
Thanks and regards,
Francesca

Hi Francesca ,
Thanks for reporting your concern.
When the target group is displayed on the WebUI, the system uses a standard structure crmt_mkttg_genil_tg_i_enhance. The fields available for selection comes from this structure. In this structure there are some 30 user fields provided which can be filled through the badi 'CRM_MKTTG_SEG_MEM_EX'. Using this badi you can display the required Custom details.
Hope this helps.

Adding new custom fields in FB01

Hello all.
I am having a requirment as i need to add the custome fields in Fb01 transaction at item level.
I have added the custome fields in Bseg table, now i wan to display this fields in the Fb01 screen.
Is thios possible to do so.

First, I hope you are using the ECC 6.0 since this is a new functionality (or ECC 5.0????). Second, tell us the steps you have followed.
Fernando.

I added a custom field into my form in BC but it wont render.

I added a custom field into my form on BC but I cannot get it to show up whhen I preview it. Does anyone know why this is happening?

Check out this http://ellenmemorialhcc.businesscatalyst.com/contact-us.html In this site I am just trying to add a 4 checkboxes. I have tried previewing it and everything and it will not make the changes. How do i get these checkboxes to show up on my site. I found where in business catalyst to access them and I enabled those features in BC but i cannot figure out how to get this to show up live on my business catalyst site.

Adding a Custom VSA to a Group - ACS Appliance

Similar Messages

Maybe you are looking for