Adding a second controller

I have one 50 license wlan controller and have maxed out it licenses. I want to add a second controller and convert the remaining APs I have to lightweight. How do I setup the second controller will all the same SSIDS, WLANs, etc? Is there an automated way? I want clients to be able to roam across access points on the 2 different controllers without issues.

The 2nd controller will need to be setup with the same SSID's VLANS and so on. After your interfaces and ssid's are created you will need to setup a mobility group with both controllers for fast roaming.

Similar Messages

  • Adding a second controller - 3750G integrated WLC

    Hello all -
    I'm new at this, so please bear with me.
    I've been tasked to add a second WLC to a customer's network. They currently have a 4402-50 supporting 47 access points. The customer purchased a 3750G w/ integrated WLC (50AP) anticipating the addition of several more APs, but the addition is on hold. In the meantime, the customer would like the new WLC to help balance the AP load. The existing WLC is running 6.0.182.0. The customer has a mix of 1130, 1240, 1140 and 1250 APs. They are starting to use N features.
    Both controllers are now on the same subnet 10.1.113.x. I've upgraded the code on the 3750G_WLC to match the other controller. Here are some questions I have now:
    1. Am I right to think I need to set these two controllers in the same mobility group?
    2. Am I right in thinking I will need to manually configure each AP to point to the controller I want it to be associated with? In other words, is there an AUTOMATIC load balancing feature? (NOTE: The customer just purchased and will have installed WCS)
    3. Once we exceed 50 APs, will any other configuration changes need to happen?
    This is all a little sketchy for me because we are right at the limit. So.. right now we are N+1 asking to load balance between the two. Once we exceed 50 APs, we're no longer N+1 and will need to designate which APs are high priority in case of failover.
    Any tips on installing this second WLC into the network and any recommendations you may have for managing these 47 existing APs is appreciated.
    Cheers -

    So, when you define primary and secondary Controller, you specify the name of the controller. In 5.2 and above you also can specifiy the Management IP address of that controller. The AP will learn about these controller through the mobility group defined on the controllers.
    About losing the controller, I didn't mean to configure priority after the fact. I meant that if you are trying to define priority (for the event that a controller was lost), then you would set the priority on the High Avail tab on the AP configuration. You would want to this when you install everything to begin with.
    If you do not define primary/secondary, the AP should learn about the controllers from each controller, and when the controller sends its discovery replies, it should specify which one to load-balance to. Or something like that.
    The bottom line is that if you don't have a primary/secondary defined, then the AP discovery process should get your AP on the least occupied controller. It is primary/secondary definitions that kind of overwrite this, which is what I was calling a "manual" load-balancing...
    Does that help any more?

  • Issues adding a second 4402 wireless controller

    I currently have 1 4402 wirless controller that is controlling the 17 APs I have in our corporate office and 18 APs we have in a warehouse 10 miles away. The warehouse has all of the APs set to H-REAP so that they can connect across the WAN to reach the controller.I have purchased a second 4402 and have placed the controller at the warehouse to handle all traffic out at that site and to relieve issues we have when the WAN gets saturated.
    I have configured the 4402 at the Warehouse with the same basic setup as the first controller (well, different IP and different VLAN and different SSIDs so I can tell I am on the new one easily). The problem I am having is that I cannot get any of the access points to log onto the second controller. All access points still show up on the first controller.
    To reach the first controller I had placed the information in the WIndows DHCP scope (Option 241 I believe) to talk to the first controller. I have change dthat to point to the second controller but that does not help. I saw that the first controller was set to be the MAster, so I turned that off to no avail. I even created a new vlan, created the DHCP information, and then added the Access Points to the new VLAN. Still, they connect to the first controller.
    Lastly, I logged into the APs and reset them to factory defaults. The APs still find the first controller.
    Any ideas what I may be missing to have them hit the new controller?
    Thanks much!
    Dave

    These are from the AP I am trying to join to the Controller and the logs on the Controller. Looks like I have a setting wrong somewhere on the Controller that I am just missing.
    *Mar  1 00:00:05.066: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:06.275: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:06.370: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 144 messages)
    *Mar  1 00:00:06.403:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:07.429:  STUB Called : crypto_ssl_init
    *Mar  1 00:00:08.472: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:08.533: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(23c)JA, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2010 by Cisco Systems, Inc.
    Compiled Tue 01-Jun-10 11:44 by prod_rel_team
    *Mar  1 00:00:08.621: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:08.622: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:08.873: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:08.873: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:09.472: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:09.876: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:09.914: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:09.927: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.331: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:16.997: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.16.12.60, mask 255.255.255.0, hostname ap
    *Mar  1 00:00:27.497:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:27.565: Logging LWAPP message to 255.255.255.255.
    Translating "CISCO-CAPWAP-CONTROLLER.madden.com"...domain server (172.16.12.11)
    *Mar  1 00:00:38.623: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.12.12 obtained through DHCP
    Translating "CISCO-LWAPP-CONTROLLER.madden.com"...domain server (172.16.12.11)
    *Mar  1 00:00:38.623: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:00:39.624: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Mar  1 00:00:39.626: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.madden.com
    *Mar  1 00:00:39.629: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.madden.com
    *Mar  1 00:00:50.632: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *May 17 21:33:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.12.13 peer_port: 5246
    *May 17 21:33:15.002: %CAPWAP-5-CHANGED: CAPWAP changed state to 
    *May 17 21:33:16.822: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.12.13 peer_port: 5246
    *May 17 21:33:16.824: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.12.13
    *May 17 21:33:16.824: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 17 21:33:21.823: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.12.13
    *May 17 21:33:21.825: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.12.13
    *May 17 21:33:21.825: %DTLS-5-PEER_DISCONNECT: Peer 172.16.12.13 has closed connection.
    *May 17 21:33:21.826: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.12.13:5246
    *May 17 21:33:21.827: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *May 17 21:33:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.12.13 peer_port: 5246
    *May 17 21:33:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to 
    *May 17 21:33:15.831: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.12.13 peer_port: 5246
    *May 17 21:33:15.833: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.12.13
    *May 17 21:33:15.833: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 17 21:33:20.832: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.12.13
    *May 17 21:33:20.834: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.12.13
    *May 17 21:33:20.834: %DTLS-5-PEER_DISCONNECT: Peer 172.16.12.13 has closed connection.
    *May 17 21:33:20.834: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.12.13:5246
    *May 17 21:33:20.836: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *May 17 21:33:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.1.105 peer_port: 5246
    *May 17 21:33:13.001: %CAPWAP-5-CHANGED: CAPWAP changed state to 
    *May 17 21:33:14.937: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.1.105 peer_port: 5246
    *May 17 21:33:14.939: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.1.105
    *May 17 21:33:14.939: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *May 17 21:33:15.184: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *May 17 21:33:18.402: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN
    *May 17 21:33:18.404: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *May 17 21:33:18.478: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller INWDPWC01
    *May 17 21:33:18.547: %LWAPP-3-CLIENTEVENTLOG: SSID Madden_Guest added to the slot[0]
    *May 17 21:33:18.572: %LWAPP-3-CLIENTEVENTLOG: SSID LEX_Guest added to the slot[0]
    *May 17 21:33:18.590: %LWAPP-3-CLIENTEVENTLOG: SSID Madden_Internal added to the slot[0]
    *May 17 21:33:18.607: %LWAPP-3-CLIENTEVENTLOG: SSID LEX_HAND_SCANNERS added to the slot[0]
    *May 17 21:33:18.632: %LWAPP-3-CLIENTEVENTLOG: SSID Madden_Zebra added to the slot[0]
    *May 17 21:33:18.756: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    *May 17 21:33:19.404: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    (Cisco Controller) >debug capwap events enable
    (Cisco Controller) >debug capwap errors enable
    (Cisco Controller) >debug pm pki enable
    (Cisco Controller) >
    (Cisco Controller) >*sshpmLscTask: May 17 16:30:44.379: sshpmLscTask: LSC Task received a message 4
    *sshpmLscTask: May 17 16:32:44.380: sshpmLscTask: LSC Task received a message 4
    *spamReceiveTask: May 17 16:33:14.641: 00:16:47:75:19:30 Discovery Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:14.642: 00:16:47:75:19:30 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 50, joined Aps =0
    *spamReceiveTask: May 17 16:33:14.643: 00:16:47:75:19:30 Discovery Response sent to 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:14.643: 00:16:47:75:19:30 Discovery Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:14.643: 00:16:47:75:19:30 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 50, joined Aps =0
    *spamReceiveTask: May 17 16:33:14.643: 00:16:47:75:19:30 Discovery Response sent to 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:14.644: 00:16:47:75:19:30 Received LWAPP DISCOVERY REQUEST to 00:1b:d4:6b:bb:a0 on port '2'
    *spamReceiveTask: May 17 16:33:14.644: 00:16:47:75:19:30 Discarding discovery request in LWAPP from AP supporting CAPWAP
    *spamReceiveTask: May 17 16:33:25.638: 00:16:47:75:19:30 DTLS connection not found, creating new connection for 172:16:12:60 (28081) 172:16:12:13 (5246)
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: called to get cert for CID 1824fb87
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.639: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetSshPrivateKeyFromCID: called to get key for CID 1824fb87
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetSshPrivateKeyFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetSshPrivateKeyFromCID: comparing to row 1, certname >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetSshPrivateKeyFromCID: comparing to row 2, certname >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.640: sshpmGetSshPrivateKeyFromCID: match in row 2
    *spamReceiveTask: May 17 16:33:25.793: sshpmGetIssuerHandles: locking ca cert table
    *spamReceiveTask: May 17 16:33:25.793: sshpmGetIssuerHandles: calling x509_alloc() for user cert
    *spamReceiveTask: May 17 16:33:25.793: sshpmGetIssuerHandles: calling x509_decode()
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetIssuerHandles: C=US, ST=California, L=San Jose, O=Cisco Systems, CN=C1200-0015fae6db09, [email protected]
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetIssuerHandles:   O=Cisco Systems, CN=Cisco Manufacturing CA
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetIssuerHandles: Mac Address in subject is 00:15:fa:e6:db:09
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetIssuerHandles: Cert Name in subject is C1200-0015fae6db09
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetIssuerHandles: Cert is issued by Cisco Systems.
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: called to get cert for CID 26a39b4a
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.798: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.798: ssphmUserCertVerify: calling x509_decode()
    *spamReceiveTask: May 17 16:33:25.806: ssphmUserCertVerify: user cert verfied using >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.806: sshpmGetIssuerHandles: ValidityString (current): 2012/05/17/21:33:25
    *spamReceiveTask: May 17 16:33:25.806: sshpmGetIssuerHandles: ValidityString (NotBefore): 2006/01/17/19:00:47
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetIssuerHandles: ValidityString (NotAfter): 2016/01/17/19:10:47
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetIssuerHandles: getting cisco ID cert handle...
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.807: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:25.808: sshpmFreePublicKeyHandle: called with 0x31b5178c
    *spamReceiveTask: May 17 16:33:25.808: sshpmFreePublicKeyHandle: freeing public key
    *spamReceiveTask: May 17 16:33:27.455: 00:16:47:75:19:30 DTLS Session established server (172.16.12.13:5246), client (172.16.12.60:28081)
    *spamReceiveTask: May 17 16:33:27.455: 00:16:47:75:19:30 Starting wait join timer for AP: 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:27.460: 00:16:47:75:19:30 Join Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:27.462: 00:16:47:75:19:30 Deleting AP entry 172.16.12.60:28081 from temporary database.
    *spamReceiveTask: May 17 16:33:27.462: 00:16:47:75:19:30 MIC AP is not allowed to join by config
    *spamReceiveTask: May 17 16:33:27.462: 00:16:47:75:19:30 State machine handler: Failed to process  msg type = 3 state = 0 from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:27.462: 00:16:47:75:19:30 Failed to parse CAPWAP packet from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.456: 00:16:47:75:19:30 Join Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.456: 00:16:47:75:19:30 Join request received from AP which is already present. Deleting previous connection
                                                                                                                                                 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.457: 00:16:47:75:19:30 Multiple Join Request: Join request received from AP which is already present. Deleting previous conne
    *spamReceiveTask: May 17 16:33:32.457: 00:16:47:75:19:30 Finding DTLS connection to delete for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:32.457: 00:16:47:75:19:30 Disconnecting DTLS Capwap-Ctrl session 0x13869100 for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:32.457: 00:16:47:75:19:30 CAPWAP State: Dtls tear down
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 DTLS connection not found. Ignoring join request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 State machine handler: Failed to process  msg type = 3 state = 0 from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 Failed to parse CAPWAP packet from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 DTLS connection closed event receivedserver (172:16:12:13/5246) client (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 No entry exists for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 No AP entry exist in temporary database for 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:32.459: 00:16:47:75:19:30 Discarding non-ClientHello Handshake OR DTLS encrypted packet from  172.16.12.60:28081)since DTLS session is not established
    *spamReceiveTask: May 17 16:33:32.462: 00:16:47:75:19:30 DTLS connection not found, creating new connection for 172:16:12:60 (28081) 172:16:12:13 (5246)
    *spamReceiveTask: May 17 16:33:32.462: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: called to get cert for CID 1824fb87
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetSshPrivateKeyFromCID: called to get key for CID 1824fb87
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetSshPrivateKeyFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetSshPrivateKeyFromCID: comparing to row 1, certname >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetSshPrivateKeyFromCID: comparing to row 2, certname >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.463: sshpmGetSshPrivateKeyFromCID: match in row 2
    *spamReceiveTask: May 17 16:33:32.614: sshpmGetIssuerHandles: locking ca cert table
    *spamReceiveTask: May 17 16:33:32.614: sshpmGetIssuerHandles: calling x509_alloc() for user cert
    *spamReceiveTask: May 17 16:33:32.614: sshpmGetIssuerHandles: calling x509_decode()
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetIssuerHandles: C=US, ST=California, L=San Jose, O=Cisco Systems, CN=C1200-0015fae6db09, [email protected]
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetIssuerHandles:   O=Cisco Systems, CN=Cisco Manufacturing CA
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetIssuerHandles: Mac Address in subject is 00:15:fa:e6:db:09
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetIssuerHandles: Cert Name in subject is C1200-0015fae6db09
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetIssuerHandles: Cert is issued by Cisco Systems.
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: called to get cert for CID 26a39b4a
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.619: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.619: ssphmUserCertVerify: calling x509_decode()
    *spamReceiveTask: May 17 16:33:32.627: ssphmUserCertVerify: user cert verfied using >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetIssuerHandles: ValidityString (current): 2012/05/17/21:33:32
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetIssuerHandles: ValidityString (NotBefore): 2006/01/17/19:00:47
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetIssuerHandles: ValidityString (NotAfter): 2016/01/17/19:10:47
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetIssuerHandles: getting cisco ID cert handle...
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: called to evaluate
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.627: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<
    *spamReceiveTask: May 17 16:33:32.628: sshpmFreePublicKeyHandle: called with 0x31b53840
    *spamReceiveTask: May 17 16:33:32.628: sshpmFreePublicKeyHandle: freeing public key
    *spamReceiveTask: May 17 16:33:34.288: 00:16:47:75:19:30 DTLS Session established server (172.16.12.13:5246), client (172.16.12.60:28081)
    *spamReceiveTask: May 17 16:33:34.288: 00:16:47:75:19:30 Starting wait join timer for AP: 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:34.293: 00:16:47:75:19:30 Join Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:34.294: 00:16:47:75:19:30 Deleting AP entry 172.16.12.60:28081 from temporary database.
    *spamReceiveTask: May 17 16:33:34.294: 00:16:47:75:19:30 MIC AP is not allowed to join by config
    *spamReceiveTask: May 17 16:33:34.294: 00:16:47:75:19:30 State machine handler: Failed to process  msg type = 3 state = 0 from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:34.294: 00:16:47:75:19:30 Failed to parse CAPWAP packet from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 Join Request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 Join request received from AP which is already present. Deleting previous connection
                                                                                                                                                 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 Multiple Join Request: Join request received from AP which is already present. Deleting previous conne
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 Finding DTLS connection to delete for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 Disconnecting DTLS Capwap-Ctrl session 0x138691e8 for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:39.289: 00:16:47:75:19:30 CAPWAP State: Dtls tear down
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 DTLS connection not found. Ignoring join request from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 State machine handler: Failed to process  msg type = 3 state = 0 from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 Failed to parse CAPWAP packet from 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 DTLS connection closed event receivedserver (172:16:12:13/5246) client (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 No entry exists for AP (172:16:12:60/28081)
    *spamReceiveTask: May 17 16:33:39.291: 00:16:47:75:19:30 No AP entry exist in temporary database for 172.16.12.60:28081
    *spamReceiveTask: May 17 16:33:39.292: 00:16:47:75:19:30 Discarding non-ClientHello Handshake OR DTLS encrypted packet from  172.16.12.60:28081)since DTLS session is not established

  • Adding a second internal HDD on a Satellite A350-20s

    I have a Satellite A350-20s.
    It is described in its documentation as having the option to add a second internal 2"5 hdd, and a indeed there is a place reserved for it..
    The problem is that when I remove the cover to insert the hdd there is no connector.
    So, how to do it ?

    Hi buddy,
    Well, I have even checked the manual of my Satellite A350 and there you can see that the manual shows second HDD slot. But as Paolo30 wrote installing such a HDD is depending on the HDD controller You can only install such a HDD if you have a second HDD connector.
    In my opinion all its ok because the manual doesnt mention that adding a second HDD is possible on every notebook. ;)
    By the way: If you need more disk space you can use an external HDD, for example 2.5 one. Such HDDs dont need an additional power supply, you need only an USB cable to connect it. ;)

  • I can't get my ICloud started. Each time i try to sign in..it indicates that theres a problem with my email apple address but never indicates what. I added a second email but the same result. Have changed my password numerous times...no result?????

    I have followed the instruction relating to Icloud connection.When i went to system preferences, my Apple address is continually rejected. I have added a second email as suggusted by an Apple site but i still get the same message. Im not told why the Apple ID/email is not accepted when it is accepted in all other Apple sites. I changed my password numerous times to ensure it wasnt the password but to no result. It continued to state that my Apple ID was the problem. I live in Malta,Europe. Have new Apple Mac Pro and Ipod. The annoying thing is that ICloud continually send me the problem notice but do nothing to tell me how to fix it? Can i switch this notice off? Help???????

    Welcome to the Apple community Yao.
    If you mean that Find My Phone is asking for a password to a different Apple ID to your current Apple ID.
    This feature has been introduced to make stolen phones useless to those that have stolen them.
    However it can also arise when the user has changed their Apple ID details with Apple and not made the same changes to their iCloud account/Find My Phone on their device before upgrading to iOS 7, or if you restore from a previous back up made before you changed your details.
    The only solution is to change your Apple ID back to its previous state with Apple at My Apple ID using your current password, you don’t need access to this address if it’s previously been used with your Apple ID, once you have saved these details enter the password as requested on your device and then turn off "find my phone" and delete the account from your device.
    You should then change your Apple ID back to its current state, save it once again and then log back in using your current Apple ID. Finally, turn "find my phone" back on once again.
    This article provides more information about Activation Lock.

  • Adding a second time capsule?

    I've reviewed some of he discussion on adding a second Time Machine but two issues arise.  The information relates to older Time Machine software and leads to confusion.
    I have an Airport Extreme with S/W version 7.6.4 and would like to add a newer Airport Extreme to back up the older one.  Reading the suggestions on adding a new TC didn't cover the newer Time Machines and I could find Apple's instructions for doing it.
    Somewhere I read that the new TC could be connected to the old TC but forgot the port setup.  Also, newer instructions for adding a second TC so both the old and the new acquire the same data could not be found.
    Hope This question is clear.  Is there help on this?

    The network setup is fairly trivial.
    Plug TC2 into TC1. (the hardware is Time Capsule.. TC as per your title.. or is it Airport Extreme as per your question..?? Time Machine is software on your computer.. and totally unrelated to the hardware.)
    Makes no difference which way around you do it. Plug WAN of the 2nd device into LAN of the 1st device. And setup the 2nd device in bridge.. wireless is up to you.. off or on?? Roaming or not??
    As far as backup is concerned.. you need to be clear in the question. And sorry it is a bit mixed up now.
    But I can tell you what you cannot do.
    You cannot backup to both units at once. You can however setup Time Machine in the computer to backup sequentially to both.
    See Q34 http://pondini.org/TM/FAQ.html
    The TC itself cannot backup to another TC.
    (extreme with hard disk amounts to the same thing.. with caveats)
    You can backup one TC to another manually via a computer.. it is slow and I do not recommend it.. if a fault creeps into backup1, you are simply copying said fault to backup2.. AND it is poor for another reason.. Time Machine cannot do it.. you will need another utility eg Carbon Copy Cloner.. and even then you will probably end up backing up a huge amount of data every time.. since TM works so strangely you cannot just backup differences.

  • I am considering a Apple iMac but would be interested in adding a second monitor. Does it have to be an Apple monitor or can i add any monitor with a thunderbolt cable and DVI or vGA adapter?

    I am considering a Apple iMac but would be interested in adding a second monitor. Does it have to be an Apple monitor or can i add any monitor with a thunderbolt cable and DVI or vGA adapter?

    I found that the Thunderbolt input accepts the mini-DVI (in my case converter to VGA for a tutorial use monitor)
    BUT, you have to really oush it in 'til it clicks.  I thought it too loose until I tried it.  works just fine!!
    i get a solved for my own  LOL
    Ed

  • How to change security questions after adding a second email address?

    I'm at a loss and really really frustrated with Apple for the first time in my life.
    I've added a second email address and tried over the last 3 days on my iPad and Mac to change my security questions. There is no option present that I can see that allows you to do this without first entering the answers. (to which I don't know anymore)
    I called Apple support (even in english) and every time the call has been dropped.
    In all the years since switching to Apple I've always been impressed with the level of customer service. This is the first time that I've felt this level of sincere frustration.
    I'm not sure why I have to book a time to speak with someone. Updating or changing security questions, should be a process one can do over the internet. I'm confused either way why questions are necessary if the apple password entered was correct. It's not my bank account; why the need for such extreme security just to download an app paid for by an iTunes card!
    Any help or direction would be appreciated!!
    Thank you
    Kate

    Hello there, Kate.
    Apologies for your frustration. For your security the existing questions need to be answered before new ones can be created. The following Knowledge Base article provides some additional steps to try if you are unsure of the answers to the existing ones:
    Apple ID: All about Apple ID security questions
    http://support.apple.com/kb/HT5665
    Specifically:
    What should I do if I don't remember the answers to my Apple ID security questions?
    Try answering them at least once to see if you can get them right, even if you are not sure you remember the answers to your security questions.
    If you are confident you can't remember them, try one of the following:
    If you have three security questions and a rescue email address
    sign in to My Apple ID and select the Password and Security tab to send an email to your rescue email address to reset your security questions and answers. 
    If you have one security question and you know your Apple ID passwordsign in to My Apple ID and select the Password and Security tab to reset your security question.
    If you have one security question, but don't remember your Apple ID password
    contact Apple Support for assistance. Learn more about creating a temporary support PIN to help Apple confirm your identity when you contact Apple Support.
    Note: If you have forgotten your password and answer your security questions incorrectly too many times in a row, you will be unable to try to answer your security questions for a period of time. During that time you will not be able to reset your password and will not have access to your account.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro D.

  • Adding a second optical drive

    Hi,
    I've have just added a second optical drive to my MP, it's an LG, "HL-DT-ST DVDRAM GSA-4120B" according to system profiler. I'v left the original apple superdrive as-is, and put this in the second bay. I'm pretty sure I've set it's jumpers to "slave", but it was in an external bay and I don't have a manual or anything, so I'm not 100% sure.
    Both drives work fine, on their own, but they don't seem to want to work together. Programs seem to have to wait for the 2nd drive to finish whatever it is it's doing, before they can get access to 1st drive (or vice-versa).
    I was under the impression that both drives can be working at the same time, and it would seem pointless having two drives if they can't work at the same time?
    I don't have to change anything about the original superdrive when adding a second drive, do I?

    Hi,
    I've have just added a second optical drive to my MP,
    it's an LG, "HL-DT-ST DVDRAM GSA-4120B" according to
    system profiler. I'v left the original apple
    superdrive as-is, and put this in the second bay. I'm
    pretty sure I've set it's jumpers to "slave", but it
    was in an external bay and I don't have a manual or
    anything, so I'm not 100% sure.
    Both drives work fine, on their own, but they don't
    seem to want to work together. Programs seem to have
    to wait for the 2nd drive to finish whatever it is
    it's doing, before they can get access to 1st drive
    (or vice-versa).
    I was under the impression that both drives can be
    working at the same time, and it would seem pointless
    having two drives if they can't work at the same
    time?
    I don't have to change anything about the original
    superdrive when adding a second drive, do I?
    Looking at your specs. the drive is an LG. I have an LG as well not the same model but I set my jumper to Cable Select, that is what worked and it is the same setting as the original Sony SuperDrive.
    I am certain it will work as it did no mine.
    My specs:
    ATA Bus:
    SONY DVD RW DW-D150A:
    Model: SONY DVD RW DW-D150A
    Revision: 1.MD
    Serial Number:
    Detachable Drive: No
    Protocol: ATAPI
    Unit Number: 0
    Socket Type: Internal
    Low Power Polling: No
    HL-DT-ST DVDRAM GSA-H10L:
    Model: HL-DT-ST DVDRAM GSA-H10L
    Revision: LL10
    Serial Number: K18E8582228
    Detachable Drive: No
    Protocol: ATAPI
    Unit Number: 1
    Socket Type: Internal
    Low Power Polling: No
    William

  • Adding a Second Airport Express

    Is there a trick to adding a second Airport Express?  My network is created by an Airport Extreme.  Six months ago, I added an Airport Express to get better coverage upstairs (no problems).  Now I want to add a second Airport Express to extend coverage to the back of our house.  I plug in the Airport Express but it never shows in the Airport Utility.  I have tried over and over and it never appears.

    The second Express can "extend" the signal provided by the AirPort Extreme, but it cannot "extend" the signal from the AirPort Express that is already "extending".
    The Express always needs to be located where it can receive a strong signal from the main router in order to "extend" that signal.
    Might that be the issue here?  The second Express is possibly located too far from the AirPort Extreme?
    If we need to do some more checks, is your Mac runnign OS X 10.6.8 as your profile indicates?

  • Added a second IP to our server = Now users can't log-in

    Hi,
    I had a server that was working fine. It had one external IP address. I then added a second external (dedicated) IP address to the same ethernet port, by adding a second port in "Network Preferences" and manually typing in the IP configuration - just as I did for the original ethernet interface when the server was originally configured.
    The reason I added a second IP address is so that I could run Apache2 on port 80 on the new IP while continuing to run Apache1.3 on port 80 of the original IP.
    Of course now I've screwed up the reverse DNS and such and my users can't login over AFP (though SMB is ok). My initial IP has a properly configured reverse lookup, the new IP does not. The new IP is using the ISP's default domain name.
    In a situation like this, am I supposed to configure both IPs to resolve to the same computer name? myServer.company.com ? Or should each IP resolve differently..
    Thanks
    Woody

    Of course now I've screwed up the reverse DNS and
    such and my users can't login over AFP (though SMB is
    ok).
    How do the users connect to AFP? WAN or LAN, Hostname or IP ?
    My initial IP has a properly configured
    reverse lookup, the new IP does not. The new IP is
    using the ISP's default domain name.
    In a situation like this, am I supposed to configure
    both IPs to resolve to the same computer name?
    myServer.company.com ? Or should each IP resolve
    differently..
    Reverse lookups (PTR records) shouldn't come into it. If users use a hostname to connect then all you will need is an A record to convert the hostname to an IP. If they use an IP to connect, then no DNS is accessed. So if you cannot connect directly using the IP address then it suggests firewall or config - test for open 548 port etc.
    -david
        Server 10.4.8

  • Remove 2540 Second Controller?

    I have a 2540 running firmware 06.70.54.10 via CAM 6.1.2.8
    I need to install the baseline firmware on this array, however, the array at one time had a second controller and believes that it still has a second controller (which it does not).
    The resulting array alarms combined with the fact that the array cannot reach the phantom second controller are preventing the baseline firmware installation.
    I have tried inserting a second controller into the array and then offlining that controller and I have tried inserting the second controller and then removing (via Service Advisor) the second controller.
    In each case the second controller is then physically removed from the array.
    No matter what I do - including reregister with CAM, reset controller A, etc - the array thinks that controller B is present which is keeping me from installing the baseline because my array is generating alarms for the controller that doesn't exist.
    Before opening a ticket with Sun I wanted to see if anyone had run into this before and what the solution might be for myself and anyone who runs into this.
    Is there a way to force a 2540 to reinventory (I did a CRU inventory via Service Advisor) itself or to remove this reference to a second controller.
    This is driving me absolutely bonkers.

    nate_keegan wrote:
    I have a 2540 running firmware 06.70.54.10 via CAM 6.1.2.8
    I need to install the baseline firmware on this array, however, the array at one time had a second controller and believes that it still has a second controller (which it does not).
    The resulting array alarms combined with the fact that the array cannot reach the phantom second controller are preventing the baseline firmware installation.
    I have tried inserting a second controller into the array and then offlining that controller and I have tried inserting the second controller and then removing (via Service Advisor) the second controller.
    In each case the second controller is then physically removed from the array.
    No matter what I do - including reregister with CAM, reset controller A, etc - the array thinks that controller B is present which is keeping me from installing the baseline because my array is generating alarms for the controller that doesn't exist.
    Before opening a ticket with Sun I wanted to see if anyone had run into this before and what the solution might be for myself and anyone who runs into this.
    Is there a way to force a 2540 to reinventory (I did a CRU inventory via Service Advisor) itself or to remove this reference to a second controller.Officially, no. We do not support the migration from two (duplex) to one (simplex) controller, however we support the migration from one to two controllers.
    If you originally had two controllers on your array, you need to keep running with two controllers.
    Regards

  • Itunes page pops up continually on the pc since we added a second ipod. how do I stop the pop up? help/ to the same pc

    itunes page pops up continually on my windows Vista pc since we added a second ipod and sync it to the same pc. How do I stop the pop ups??

    Many thanks lllaass,
    The Touch Copy third party software for PC's is the way to go it seems and although the demo is free, if you have over 100 songs then it costs £15 to buy the software which seems not a lot to pay for peace of mind. and restoring your iTunes library back to how it was.
    Cheers
    http://www.wideanglesoftware.com/touchcopy/index.php?gclid=CODH8dK46bsCFUbKtAod8 VcAQg

  • Adding a second Domain Controller

    ...ok, so what you're saying is, If I don't spread out the FSMO roles, when the primary DC fails, I will likely run into problems until I seize the FSMO roles and delegate them to the secondary DC? By spreading out the FSMO roles, I am creating less work for myself in the event of a failure?
    ...Having said that, it isn't critical that I spread out the FSMO roles, but, would benefit me in the event of failure from a time stand point?

    I'm sitting at about 95% completion... but before I click finish, I had a few questions...
    I have a physical domain controller and Site-A, I want to add a secondary Domain Controller to Site-A and run it as a Virtual Machine... just in case the first DC dies, my users can still authenticate while I restore it from backup...
    I'm essentially adding a new DC to the existing domain, Global Catalog, DNS... not read only...
    I don't understand FSMO... do I need to do anything? or can I literally just add the second DC to the existing domain, enter the IP of the new DC in the secondary DNS on all my workstations (or DHCP leases settings) and call it a day? 
    Thanks for the input.. .just trying to make sure I'm not going to hose my primary DC or fek something up and create more work for myself than necessary...
    This topic first appeared in the Spiceworks Community

  • Adding a second domain controller to domain

    Neally I can do that no problem but why it is asking me again when it was already done when I added my first 2008 R2 Domain Controller .  I will try running it again and post the results.
    Thanks 

    Hi ,
    I am trying to add a second Windows 2008 R2 domain controller to a existing domain.
    but its asking me to run adprep/forestprep but I already have domain controller that is a Windows Server 2008 R2 and it is also a Schema Master Role holder .
    Any help is this regards will be much appreciated.
    Thanks
    Sunny Boparai  
    This topic first appeared in the Spiceworks Community

Maybe you are looking for

  • Old Lady trying to learn, Help please!

    Hello from this newbie! At 57 I have returned to college. I really am trying to understand Java. Below is the problem I need to answer, and my code. Can someone please explain what I am doing wrong in plain english, and give suggestions to fix it? I

  • Connect NI PCI-6602 with NI PCI-6503

    Hello, I want to connect a NI PCI-6602 Counter/Timer with the NI PCI-6503 DIO-Card. The problem is the varying number of pins. (6602->68 pins; 6503 -> 50 pins). Is there a possibility to connect both? Maybe a complete adapter? regards Thomas

  • Iphone in emergency mode after trying to download 3.0 HELP!

    I can't seem to finish the download of 3.0. Any tips? My phone is only in emergency mode and didn't take to the download.

  • Mavericks, CS6 crashes when printing

    Hi, We have just updated to Mavericks and run CS6. When we try to print from a standard page size everything is fine, but when we try and print an irregular size, say 10" x 13", it either crashes or prints a small portion of the page. This was never

  • Flatten FrameMaker RoboHTML WebHelp?

    Is it possible to put all the WebHelp output into a single directory instead of splitting out by .fm files? That would greatly simplify some build processes. FM10, RH9, all updates installed