Adding one IP address to Wireless Access Point

Here is my situation....
We have a guest wireless internet at my hospital. This wireless vlan is only allowed to access the internet and nothing else (nothing on our internal network, basically a courtesy wireless network). I would like to have the guest able to print to a particular printer on our network. Can this be done?

Sorry, I'm an idiot. ha ha. yeah i added the printer to the guest network and it worked. Thank you!
Since it was a private VLAN, i had to hook up a computer on the wireless and get its ip address and subnet. Thank you!

Similar Messages

Wirelessly adding a new device: Router versus Access Point versus Bridge

My home network consists of a Linksys WRT54GS Wireless router with a couple hardwired PC and a wireless laptop. I want to wirelessly connect my TiVo into this network to download saved video onto the hardwired PCs, and to give my TiVo access to the internet (it currently uses a phone line). It looks to me like the choices to include the TiVo into my home network are to connect it (wired) to:
(1) a Wireless Access Point (WAP54G),
(2) a Wireless Bridge (WET54G), or
(3) another Linksys Router (WRT54G) configured as WAP (router mode rather than gateway).
Are all three options above valid options? If so I would like to understand what the differences between these choices are, and under what circumstances would one be better than the other.
As part of this, is there a reason the Linksys Routers are much cheaper than the WAP or Bridge hardware. This is counter-intuitive since the Router appears to be the more complex hardware with multiple connectors, more memory, etc.
Thanks.

Well i would suggest you to get an Access point WAP54G as it works wirelessly & you will be able to use many pc's using it without a router.With WET54G you need to connect using the hardwired cable & you need to connect it using the cables to the pc's & configure it.With router you need another router & you can configure it accordingly in a wireless mode to make it act as an access point.

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

Apple TV 2G (Airplay and Homesharing) can only stream from devices on the same wireless access point range??

connection:
40 Mbps Fiber Broadband connection using:
Devices:
1. Main Modem/router (AP1): Huawei HG8245 (provided by ISP) - Wireless enabled.
2. Remote Access point (AP2): Linksys/Cisco E3200 Wireless gigabyte router flashed with DD-WRT v24-sp2 (06/14/11) mini (Cascaded -wired- LAN to LAN from main modem).
3. Wireless Repeater to cover a dead spot (AP3): Linksys/Cisco E1000 wireless repeater.
4. Apple Tv (AT2G) with home sharing/airplay enabled.
5.( Ipad) with home sharing on itunes enabled.
6. Win7 (PC) using iTunes with Home sharing enabled.
all devices are updated to their latest firmware.
In order to cover a large 3 story house with Wifi. I had (AP1) is located on the first floor, while (AP2) is located in the basement floor directly wired by LAN to LAN with (AP1). (AP3) is located on the Ground floor away from the living room to repeat wireless network into the back yard. While (AT2G) is located in the living room on the ground floor right in the middle of both (AP1) + (AP2) while connected via Wifi.
Network SSID, security, passphrase and wireless settings of (AP2) are identical to (AP1) to create a single big LAN/WLAN roaming network where all devices connected to both wireless access points can find/share the others. As understood, it's refered to as bridging.
I have noticed that my iphone/ipad does not show the airplay button anywhere within the wireless network. it seems that the apple TV randomly choses to connect to the AP with stronger signal, or switch to the other in case of a reboot to one of them.
to elaborate further, if i was sitting in the living room (groundfloor), trying to airplay some you tube contents via Wifi to my Apple TV, i may not find the airplay button available all the time, i found out the reason is while i'm wirelessly connected to AP1, the Apple TV was connected to AP2 and both deviced cannot detect each others to enable my purpose. that goes the same for Home Sharing. only if my Ipad/PC and Apple Tv are on the same wireless AP. they would detect each others immediately.
although, the second AP (AP2) is suppose to extend my wireless network of the same subnet in which any device connected can be found.
After all sorts of trial and error tweaking my router/access point, I thought the problem would be due to the Linksys 3200 capability of bridging WLAN and lacks few protocols that enables my purpose. i have flashed the firmware to a DD-WRT, but again, problem was not solved.
I have not tried having my Apple Tv wired to either router/AP, but i assume it may work well if i do so. i still need to solve this wireless connection issue though.
Am i the only one with this problem, would there be something wrong with my setup?
Your feedback is highly appreciated.

You may or may not already have your network set up correctly, it's just that I can't tell from what you have said.
I have a main router provided by my ISP, I have several other Airport Extremes and Airport expresses connected by Ethernet, all set up to bridge the network created by the main router.
Each maker has their own settings, but bridging should be reasonably obvious. In simple terms my main router distributes IP addresses to all devices, the Airports bridge that network by passing these addresses to the devices from the main router. A base station that isn't in bridging mode will distribute its own addresses to the devices connected to it.
I don't really follow your next point.
instruction for configuration vary from manufacturer to manufacturer, the best course of action here is to refer to the manual. If everything is set up properly the addresses of everything on your network will have identical sets of numbers for the first 3 of 4 groups of numbers that make up an address, the last set must always be different. I think the part you are referring to with your DD-WRT is the option to have Ethernet and wifi bridged or not.
Some routers may be easier to configure than others, but generally speaking they should all work with the Apple TV. 5Ghz is less likely to suffer interference but it is much more likely to be blocked by solid objects, it may or may not be an advantage.

Using WRT54GR as a Wireless Access Point only

I have a WRT610N as my main router. I want to use an existing WRT54GR purely as a wireless access point and ethernet switch. Any suggestions on how best to do that so I can still access the WRT54GR to make configuration changes? Right now I have the network functionality working by simply not using the Internet port on the WRT54G but by going to 192.168.1.1 I can only get to the WRT610N.

(Restarting this thread).
I made the change you suggested and statically assigned 192.168.1.200 to the WRT54GR. I can reliably access it through this IP address. I connected it to the rest of my network by using one of the 4 switch ports (not the Internet port). I disabled DHCP on it and configured the Wireless settings to be the same (same SSID and Security Settings) as my other wireless router.
What I'm finding is that devices in my house won't assoicate with it. I tried changing the SSID to a different value; devices were able to see the new SSID but when I entered the pasword they told me that no DHCP server could be detected. A wired device that I plugged into another of the 4 switch ports on the WRT54GR was able to pick up an IP address from the main router just fine so I know that basic connectivity is OK.
To achieve what I want (i.e. the WRT54GR just acts as a wireless base station to extend wireless coverage in the house), do I need to connect the WRT54GR to the rest of the network using the Internet port rather than a switch port? If so, what configuration settings do I need to set up so that all the devices can get their IP address from the main router?

1242AG Wireless Access Point - Cannot Get DHCP IP for BVI1 interface - Multiple SSIDs...

Hello,
I am attempting to set up three Cisco 1242AG Wireless Access Points with multiple SSID's. I used the web interface and directions online to set up the two networks I want and at least one of the networks work wirelessly.
However, I have two problems:
The first, which is the most important, is that the "management" interface, BVI1, doesn't get an ip address from our DHCP server. I set the VLAN 60 (which you'll see in the documenation below) to be the native VLAN on the device as well as on the switch that the device is connected to as well as other settings in the configeration file below. Because of this, I can only manage the device via the console port which would be a huge pain once all of the devices are mounted.
The second problem is that I am not sure how to get both wireless networks broadcasting their SSID's. I have to manually type in the SSID for the second wireless network I have which I would prefer I don't have to. Anyway I can enable broadcasting on all of the SSID's?
Thank you for your time.
Regards,
Christopher Koeber
Using 7916 out of 32768 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-18.wesleysem.edu
enable secret {Number Here} {Encrypted Password Here}
enable password {Number Here} {Encrypted Password Here}
aaa new-model
aaa session-id common
dot11 syslog
dot11 vlan-name Kresge vlan 20
dot11 vlan-name Library vlan 30
dot11 vlan-name Public vlan 60
dot11 vlan-name Secure_Public vlan 70
dot11 vlan-name Secure_Seminary vlan 80
dot11 vlan-name Server_Room vlan 1
dot11 vlan-name Straughn vlan 40
dot11 vlan-name Trott vlan 10
dot11 vlan-name Web_Room vlan 50
dot11 ssid (Secure) Wesley Campus
vlan 80
authentication open
authentication key-management wpa version 2
wpa-psk ascii {Number Here} {WPA Key Here}
dot11 ssid Public
vlan 60
authentication open
mobility network-id 60
username Cisco password {Number Here} {Encrypted Password Here}
username admin privilege 15 secret {Number Here} {Encrypted Password Here}!
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 80 mode ciphers aes-ccm
ssid (Secure) Campus
ssid Public
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption vlan 80 mode ciphers aes-ccm
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio1.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio1.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface FastEthernet0
ip dhcp client update dns
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface FastEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
no bridge-group 30 source-learning
bridge-group 30 spanning-disabled
interface FastEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
no bridge-group 40 source-learning
bridge-group 40 spanning-disabled
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
no bridge-group 80 source-learning
bridge-group 80 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end

I am using a third party DHCP server which is our Windows Domain Controller. I have the ip helper-address set for the native vlan of the Access Point through a layer 3 distribution switch (a Catalyst 4506) that the current switch connects to.
I didn't see any event on the logs for the AP.
Let me know if I need to do something else.
Thanks.

Westell 327w and Wireless Access Point

I had DSL last year, but have since changed to FIOS, which I love. So I have the Westell 327W modem/router that isn't being used. I have decided to use it in another project for the 4 port ethernet and the wireless capability.
As this other project, we are using another service, which isn't DSL. However, I figured that I could use the 327w as the wireless access point. I currently have access to the internet through the provided internet service and from there I go into a Cisco ASA 5505 firewall. From there I run an ethernet cable to the 327w.
As long as I plug a computer into one of the 4 ethernet ports on the 327w, I'm able to ping to the Internet using either the IP address or using DNS. I'm able to surf and everything.
I have also set up the wireless and using WPA security and I'm able to connect a laptop to the wireless. I get the IP address via DHCP from the ASA, so I have turned off the DHCP server on the 327. I have also turned off the firewall. I then test connectivity and I can ping anything on the network that is assigned by the ASA, but when I try to ping to an Internet address, by the address, I get request timed out. I also don't get anything back on DNS and so forth.
What do I need to do on the 327 to allow the wireless to work with the current connection set up.
Thanks for the help and information.

I got it to work. What I had to do was to set up the 327w in VLAN mode so that the wireless side would send the packets out the ethernet port to the ASA or another router.
In fact, I'm writing this on the wireless setting of the 327w. So setting the VLAN allow the wireless to send and receive packets.

Set up time capsule as wireless access point

I am trying to set up my old apple time capsule as a wireless access point for my girlfriend. She is at college and the university does not permit routers, so I am trying to set the time capsule up so that is just takes the hardwired internet and allows wireless access to the internet so she can use her iPad and MacBook Air on the wireless instead of having to use a gigabit adapter to use the ethernet. The time capsule has the newest firmware and she is running mavericks which has the newest airport utility software. However I am not sure what settings to use to make this work. I am fairly intelligent when it comes to computers however I am not very skilled in networking. If anyone can help I would greatly appreciate it.
Thank you in advance!

How old is the Time Capsule? Running what firmware?
You have a problem.. If you cannot use the TC in router mode, then you are going to have to use it in bridge.. and it then depends on if the Uni system will hand out mulitple IP addresses. .which I doubt. In the end you might be stuck.. and it is not possible really with any system..
Bridge normally requires that the TC take an IP address and then clients connecting to the TC wireless will also get IP addresses.. but if the uni system only hands out one address then the TC has already captured it and there are no more available.. but try that method first.. as it is the easiest.
If it fails there is a more complicated method.. where we can give the TC a separate static IP in a different IP range and the wireless will still be bridged.. so the MBA or the ipad can use the wireless.. but only one can ever be online at a time.
The only way around this is to use the TC as a router contra the rules in the uni.. although I would suggest the uni only cares if you break their system. Most people don't.. but I am unsure what happens if you do.
Ask their IT people how to use a wireless only device like ipad, when they only provide ethernet. You might find there already is a wireless internet system as well.

Setting up WRVS4400N for switch & wireless access point

Howdy, first post here. What is the proper way to configure this device to act as a switch and wireless access point so I can connect it to a switch with router upstream? I have a DLink router that was easy: disable UPnP, disable DHCP, set an IP/Subnet, and it worked.
My main router has a subnet mask of 255.255.240.0 but in the WRVS4400N setup screen I only get a list box with a limited number of masks, all of which are 255.255.255.x. Is there any way to specify the 240?

No. You cannot use a subnet mask larger then 255.255.255.0 on Linksys routers. They are only built to handle 255.255.255.0 and smaller. I guess they consider a LAN which requires a larger subnet, i.e. expects to run more then 253 networked devices requires a larger router.
The only thing you can do is to choose 255.255.255.0 and to pick an IP address which matches the IP address from which you expect to do the usual configuration work. If you use 10.0.0.0/255.255.240.0 but the computers which have to configure the router are all in 10.0.1.0/255.255.255.0 you can use that subnet. This works with computers even if they have a different subnet mask.
Of course, you can set any IP address you want, even one completely outside your normal LAN in order to "hide" the web interface from the normal LAN operation. The IP address of the router in your setup is irrelevant for the switching and wireless access. Both operate on ethernet/MAC addresses and the IP address of the router does not play any role there. If you use the 10 subnet mentioned before you could as well leave the router at 192.168.1.1/255.255.255.0. Whenever you have to access the web interface of the router you must temporarily set a static IP address inside 192.168.1.* on the computer...

Is it possible to remove the iphone history of wireless access points to which you've connected?

So.... I work in a place where there is a lot of security and snooping. There are folks specifically assigned to track down phones in unauthorized places. Their enthusiasm is sometimes annoying.
I leave my phone in a locker outside of the restricted area. However, I recently overheard some of the "snoops" discussing a phone that they had found. They were discussing a specific wireless access point that was in that phone's history, that caused some discussion. Although the phone was located in the locker area, they had apparently discovered it and examined it.
It was my phone.
One obvious course of action is to make sure the phone is always turned off (which I will do), but they have now identified my phone by the APs to which I connect, and I'd like to erase that history.
Is it possible?
Thank you.

Settings > General > Reset > Reset Network Settings.

IOS 6.0.1 - Problems with certificate based authentication on wireless access point

Hi all
We are using iPad 2 as order terminals in our shops for about 5 months. Some of the iPads (the first who entered the field) started to cause problems now. These iPads are no longer able to keep long-term connection to the wireless access point in our stores. After selecting the SSID a successful authentication using the stored EAP-TLS certificate is performed (this can be seen in the log files of our wireless controller and by the IP adress that is given by DHCP). But within seconds the affected iPads opening up a captive portal page (empty, without contents) and separates the connection to the SSID after a short time again.
Affected are currently only iPads 2 with iOS 6.0.1, which were staged about 5 months ago. The newer devices with iOS 6.1+ connect without problems and open no captive portal page. The first cases occurred on the last Wednesday. Before that everything worked without difficulty. No modifications took place on the security structure. The numbers of affected devices increased until all iOS 6.0.1 were affected.
Access to other SSIDs (without use of certificates, by entering a key) for the devices is still possible (the devices does not open an captive portal page). The DHCP scope is not used up, so there are enough IP addresses available.
"Newer iPads" with an iOS of 6.1+ are are showing no problems on the same wireless access point, where the older devices are rejected. New and old devices use the same certificates and authentication mechanisms.
In the analysis of the issue, it turned out that the problem can be solved by an update to iOS 6.1.3. Subsequently, the iPads will be able to rebuild a connection with the access point, without a captive portal page.
Since the bandwidth is very narrow dimensioned in our stores, the communication of the iPads was severely restricted. Thus, the iPads are for exampleare accessible for the APNS but can not find iOS updates or check for their availability.
A comprehensive update to iOS 6.1.3 is currently excluded.
Does anyone knows this issue? What else can be done (except from updating)?

I will answer my own question in case it helps anyone else.
It would "seem" the ios 6 devices try the proxy and if that is not working they resort to the def gateway.
To Fix I did the following:
Brocade WIFI network has IPS and Advanced Firewall rules that seemed to be tthwarting some traffic, the iphones would then try the default gateway and be blocked at the FW.
I disabled the IPS and the Advanced Firewall Settings on the wifi as they are redundant to our main IPS and firewall that all traffic flows through anyway. I will tune it later, but when the CEO is demanding a fix "**** the security, full speed ahead"
Created some rues on the firewall to allow...
- IMAP-SSL (port993) outbound
- SMTPS (port 465) to yahoo servers outbound
- tcp port 587 to yahoo servers outbound
- https to akamai servers
Most http and https goes through the proxy as it should, BUT...
It seems that the akamai traffic allways ignores the wifi proxy settings and just heads straight for the default gateway. I suspect there is a bug in the icloud app?
Hope this helps someone else.
-Bo

N800 no longer detecting any wireless access point

The device is working fine couple days ago, then today when I turn it on, the "connection manager" can no longer see any wireless access point. Not only my home network, also
my neighbor's wlan. My laptop can detect 10 networks
around my house. I try upgrad my os to the latest version and it is still not working. Is anyone has similar experience ? Is it a hardware problem ? Any advice will be
welcome.

It happened to my N800 too just a couple of days ago after I installed a number of applications. I have already removed those applications but the N800 still would not detect the access points that it usually detects with no problem.
It could not detect the WLAN inside our house even if the N800 was physically sitting on top of the router. It would intermittently detect my neighbor's WLAN (the one which I usually use) but it would not log on to it.
I tried removing the battery hoping to reset it but nothing changed.
It also would not connect to my PC via USB. The computer could not detect it. This one happened even before I installed those applications.
Help!!!!

Can I disable my Verizon Fios Router Wireless radio, connect it to a switch and use my airport express as my wireless access point connected to an in wall ethernet port?

Here's the deal. I have a Verizon Fios MI424WR router. My house has CAT5 throughout the house. The media panel is located in the garage. I want to take the Verizon Fios Router and cannot it in the media panel so I can connect a switch to it, that way, all my CAT5 can fire throughout the house. Verizon being Verizon decided to connect the router directly in the office.
Can I go this route (Router in media panel, switch cross connect to it) and use Airport Express, connected to one of the in-wall CAT5 ports in my house and then set it up as my wireless access point to provide wifi to my portable devices (iPad, iPhone, Macbook)? Is this possible? Will Airport Express comminicate with my verizon router via ethernet in-wall? Do I have to turn off the wireless radio in the Verizon router? Any help would be greatly appreciated!

That is right, by hard wired I was just making clear wired vs wireless attachment. AirPort family of devices will only act in a repeater mode with their own family members, not FiOS routers. they have to be wired to work.
There are some useful docs you can download from Apple, Support, Manuals, Peripherals, AirPort (just follow thos links from the Support button on the top bar):
Apple AirPort Networks
Designing AirPort Networks
AirPort Express Setup Guide
The last has a diagram of what you are trying to do, though without the house wiring, etc., but the basic principle.

I can't get my macbook to access shared files on a windows computer when it's connected through a wireless access point.

I recently bought a Netgear Wireless Access Point to use in the office so we can have a wireless network. I configured the wireless network, and I am currently connected to the internet. However, I no longer can access the shared files on the Windows computers like I could when I was hardwired in with an ethernet cable. I've disabled all of the internal firewalls on all of the computers (and there's no firewall built into the WAP), all the computers are on the same workgroup, and I've tried accessing the computer with the shared files directly via the IP address using the instructions found here http://docs.info.apple.com/article.html?path=Mac/10.5/en/8849.html.
My computer sees that the other computers on the network are there. They show up in the network view from the finder. However, when I try to connect to them, it tells me the connection failed. When I click connect as, it says:
"Connection Failed
"The server “PC-ASSISTANT” may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again."
When I try to connect via the "connect to server" on the finder, I type in "smb://10.0.0.103/Word Processing" It tells me:
"There was an error connecting to the server “10.0.0.103”. Check the server name or IP address, and then try again.
If you are unable to resolve the problem contact your system administrator."
I have no clue what the problem is. I'm not really an IT person or a networking guru. Can someone please help?

You posted in the Older Hardware forum, which is for pre-year 2000 hardware. Suggest you post your question in the Airport forum at https://discussions.apple.com/community/wireless/airport
 Cheers, Tom

WRT310N as a "Wireless Access Point"

Hello,
I am in the market for a wireless device to add to an existing subnet. I see many tutorials regarding routers as wireless access points, but I am not sure if this device will work.
My plan is to connect one of the switch ports to an existing switch and not use/configure the WAN port.
I would rather purchase a router then a true WAP do to the fact that it can also act as a router (should I need it later), whereas a WAP cannot.
Any thoughts on this is appreciated.

Well try upgrading the firmware of the router & keep on holding tightly
the reset button in such a way that power light is blinking on the
router & then do a complete network power cycle i.e., unplug the power
cables from the modem & from the router & then plug in the power cable
to the modem first once all the lights are solid green you could plug
in the power cable to the router & check out it will definately work!!
Open the setup page of router using 192.168.1.1 then put in the
password as admin...all you need to do is do the wireless settings such
as Radio Band Frequency to Standard 20 MHZ frequency,channel to 11.
Also,the advanced wireless settings to Beacon Interval=50,Frag
thres=2306 & Rts thres=2307 & then uncheck a Block Anonymous Internet
Requests & it will definately work!!!

Adding one IP address to Wireless Access Point

Similar Messages

Maybe you are looking for