AirPort/App Store/Time Capsule issues since update

Ok I have a MacBook Air Mid-2013....Since I did the Yosemite update 10.10 I have experienced the following issues...
1. I cannot connect to my time capsule (well I can if I get go to connect to server and type the ip)
2. The time capsule will not show up in my airport utility (but i can get into it when I configure other)
3. I cannot connect to the App Store.
4. My internet connection seems to go out when i try to get into the app store or the airport utility.
I have turned off my firewall that didnt work. Cleared out my key chain....still nothing......made sure the time was set correctly.....Reset a bunch of times everything.....I can access the time capsule from ios and my imac which i didnt update.

Reset the TC to factory.
The Factory Reset universal
Unplug your TC/AE. Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
Release reset.
If it doesn’t flash rapidly you have released reset at some point and try again.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
Start over from the MBA and redo the setup.
Make sure you use all short names, no spaces and pure alphanumeric names.. pure alphanumeric passwords.
eg TCgen5 base station name. TCwifi wireless name.
Make sure ipv6 is set to link-local only in the computer.
.. Now you might need to setup the TC at least once manually in finder.
Use the name.. as follows
AFP://TCgen5.local
And don't forget to save the password to the keychain.
If you still have issues, it is more likely the MBA installation of Yosemite is faulty.. and I would recommend a clean install.

Similar Messages

App Store won't load since updating to Yosemite

Since I updated to OS X 10.10 Yosemite, the App Store will not load. It just sits there with the loading icon on the navigation bar.

Hi colinvignoul,
Welcome to the Apple Support Communities!
If the App Store is not launching on your computer I would suggest using the troubleshooting information in the attached article to help resolve the situation.
OS X: "Cannot connect" or "Cannot connect to the App Store. An internet connection is required"
Have a great day,
Joe

Can not open the app store on my mac since new update

can not open the app store on my mac since new update

Here are some suggestions for getting the best results from this site.
Create a user profile that accurately reflects the type of hardware you're using and your version of OS X, or include that information in your first message.
Give details of the problem. A remark such as "X doesn't work" conveys no useful information. If X did work, you wouldn't be here. Instead, you should post something like this: "I did A; I expected B; but I got C." Include the complete, verbatim text of any error messages you saw, and specify where you saw them: in an application window, a CrashReporter window, a log, or whatever.
Also describe the steps you’ve taken yourself, if any, to try to resolve the issue. If the problem is of recent origin, did you make any changes to your setup just before you first noticed it? Is the problem reproducible or intermittent? That is, does it always manifest itself when you take a certain action, or only at unpredictable times?
Before posting, ask yourself whether it’s likely that you are the the only person ever to have had this problem. If not, search the discussions for answered questions similar to yours. If you found any pertinent information, but it didn't help, give details.

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

Why am I not able to access the app store, itunes and safari since upgrading to Mavericks 10.9?

IT tells me they would have to revert to the old OS which they don't want to do or can't do? I have been two months without access. I am at a loss. any help or guidance would be appreciated. I work for state government and our servers are PC-based which I think where the problem is. Is there a work around to gain access to the app store, itunes and safari. The app store icon indicates I have updates available but I am stuck. Please advise.

I know safari is mac's native browser. Since updating to OSX10.9, I have not been able to open safari. Firefox works fine but I preferred safari. Safari just won't open, it acts like it wants to, but the progress bar goes about half way across and stops. What other information do I need to supply?
This is a very frustrating problem when I see that there are updates to apply, but am unable to open the app store to get them. I can't even see them.
IT, in my opinion, has almost thrown in the towel since they are more PC-based.I believe it is a connection problem but they have been unable to fix it. They blame mac for a hasty upgrade release that was not fully tested to see if there were any Mac/PC connection issues.
Thanks for any help you can provide.

App store says there is one update but none need updating

I just upgraded to Yosemite and under my Apple menu, the App Store shows there is one update needing to be done but when I open the App Store, it shows none need updating.
This is a week-old MacBook Pro with 2.8Ghz i5, 8GB, and 512 SSD.

Next time that happens while on WiFi, turn WiFi off in settings, wait about 30 seconds or so, then turn WiFi back on. Sometimes you have to do this two or three times, but this fixes that issue as well.

Time Machine/Time Capsule issues

I have had a never ending series of Time Machine/Time Capsule issues. There's little to configure, so there's not much I could be doing wrong.
One thing I have especially noticed, is that Time Machine is interfering with iTunes. iTunes has frozen for a time or locked up when Time Machine is backing up.
Another problem I have seen is the console log flooded with some sort of waiting for index error. Yet another are messages like -
"Jul 14 14:43:56 MJBook /System/Library/CoreServices/Finder.app/Contents/MacOS/Finder[176]: StatusMonitor::volumesChangedCallBack returned -47"
The only thing I have ever found odd about my situation is that I am running a Time Machine and three other Airport Express devices. One of the Airport Express units uses WDS, and I heard that could create issues.
Any ideas?

I have the same question and I see you posted yours in March. So this forum is REALLY helpful...
My Mac consultant doesn't use either so is not much help. He says to erase T.C. and start over, but it also contains all my backups for my other Mac which have worked perfectly. When I select T.C. in T.M. the only option is to Remove Disk; I want to save the MacBook backups. I also tried wireless as he suggested but got the same warnings as above so went back to Ethernet. Plus nobody can tell me how to access T.C. in Disk Utility to try to fix it.

Time Machine, AirPort Utility, and Time Capsule broken in Mavericks?

Hi all, I’ve got a befuddling Time Machine/Time Capsule/Airport problem that I can’t seem to sort out.
On my pristine 2-day-old iMac (late 2013, running 10.9.1), I’m trying to set up Time Machine to back up to a new-ish 3TB Time Capsule. Initially it worked fine for the first backup, but subsequent backups failed because “backup disk could not be found.”
So I tried giving the TC a shorter name. The first backup under the new name worked a treat, but subsequent backups failed.
In Time Machine system pref pane, I deleted the Time Capsule, intending to try again with a new, even shorter name. But then when I went into AirPort Utility to change the Time Capsule name, it told me that “no configured AirPort base stations have been found.” I assumed that I was just deleting it as a choice on the backup disk list, but now I'm wondering, did the Time Machine pref actually delete the actual disk? In the AirPort Utility window, Time Capsule appears in the "other wi-fi" devices list, yet when I click it, it says "error reading settings."
Here are some other random details that may or may not pertain:
On the new iMac, I tried to mount the TC disk image, but Connect To Server reports that the connection fails because “the server may not exist or is unavailable.”
Although the Time Capsule shows up in the sidebar of the Finder window, “getting info” just produces the spinning wheel.
Although AirPort utility says that it can’t find the Time Capsule, the TC is nevertheless connecting to the internet just fine. All household devices are online, including iPhones and iPads.
On the old Mac Pro running 10.8, Time Capsule, Time Machine, and AirPort Utility all behave normally.
I thought I might try resetting the Time Capsule, but will this erase all the backups (from other computers around the house all running 10.8x without problems of any kind) that are on there? The other computer users will definitely squawk about that!
I hope this tirade makes some sense. Thanks for reading!

1. In Time Machine system pref pane, I deleted the Time Capsule, intending to try again with a new, even shorter name. But then when I went into AirPort Utility to change the Time Capsule name, it told me that “no configured AirPort base stations have been found.” I assumed that I was just deleting it as a choice on the backup disk list, but now I'm wondering, did the Time Machine pref actually delete the actual disk? In the AirPort Utility window, Time Capsule appears in the "other wi-fi" devices list, yet when I click it, it says "error reading settings."
Here are some other random details that may or may not pertain:
2. On the new iMac, I tried to mount the TC disk image, but Connect To Server reports that the connection fails because “the server may not exist or is unavailable.”
3. Although the Time Capsule shows up in the sidebar of the Finder window, “getting info” just produces the spinning wheel.
4. Although AirPort utility says that it can’t find the Time Capsule, the TC is nevertheless connecting to the internet just fine. All household devices are online, including iPhones and iPads.
5. On the old Mac Pro running 10.8, Time Capsule, Time Machine, and AirPort Utility all behave normally.
6. I thought I might try resetting the Time Capsule, but will this erase all the backups (from other computers around the house all running 10.8x without problems of any kind) that are on there? The other computer users will definitely squawk about that!
I hope this tirade makes some sense. Thanks for reading!
Rather than chop up your post I have taken the liberty to number the points.
1. When you deleted the TC in the airport utility you simply changed its ability to display the errant device. You did not actually delete anything on the TC itself.
Getting back a lost Airport.. more below.
2. Please give actual command you used.. and the name..
It is most important that you translate the name from Apple name to actual network name. That is why I constantly hammer on about using network names.. short, no spaces and pure alphanumeric.
So Fred Blog's Airport Time Capsule apart from being hopelessly wrong.
Is translated by Apple to the Network name.. Fred-Blogs-Airport-Time-Capsule (note.. no spaces and no special characters.. the apostrophe is deleted).
It can be much easier to just use IP address.. if the TC is the main router.. then it will hold a constant IP.. by default 10.0.1.1
So mount the TC as AFP://10.0.1.1
3. That is standard.. it is a network device and will not show info. Same on any computer in your network.. same on any OS.
4. Yes, that is standard.. the location of the hard disk is lost.. but the internet is still working.. This is the bug that has been around since Lion and is still growing worse with each revision.
5. Again standard. the issue is on the computer or the interaction of the two.. computer and TC.. yet other computers are unaffected.
6. Reset of the TC is fine.. no reset, soft hard or factory will ever delete the hard disk files.
But if you change the name of the TC, you will need to go around to all the computers and setup TM again to point to the right target.. none of the backups are lost.. you just need to tell TM where they got to.
Manual setup of the lost TC.
In Airport utility go to the top menu, open configure other.. and type in the IP address of the TC that got lost.
no password needed unless you set something .. if it doesn't work the default is public

Airport express / extreme / Time Capsule Range

Airport express / extreme / Time Capsule Range
Can anyone please tell me what is the approximate range of Apple Airport Products.
While doing sell in Apple store customer always ask us this question and we don't had any answer for it.
So please if anyone has the answer do reply on this.
- - - Akshay k. (ACMT)

The range is about 50 meters or 150 feet.....but this assumes that the AirPort is being used in a very large open space like a aircraft hangar.....with no obstructions in the signal path.
Chances are, your home is laid out a bit differently, so without knowing a number of variable factors like.....
1) How many walls there will be in the signal path between wireless devices
2) The actual construction type of the walls, ceilings, etc
3) Heavy furniture, large mirrors, etc. in the signal path
4 ) Other wireless networks around your home
5) Other wireless devices like cordless phones, BlueTooth devices, etc.
It would be impossible to tell you what the actual range might be in your home.
In general, assuming normal modern home construction, you would not want the wireless signal to pass through more than 2 or 3 walls....since each wall will absorb on average about 15-25% of the wireless signal. A ceiling will absorb even more because of its thickness.

App store id greyed out for updates?

Hi i have a problem with the app store and that problem is i go to update my apps and it has a user id that it wont let me change to the one i normally use(the ones thats there is greyed out and i cant change it) ,i have had no problem with this prior whether its updating or downloading new apps.i would like to fix this issue to i can add some updates.thanks for your time and have a great day.(i can still install apps amd sign in normally with the exception of updateing the osx apps)
OS X Mavericks (10.9.1)

You installed a hacked app, originally from the Mac App Store. It contains the receipt for a different app, downloaded using an account that you don't control. You need to identify and remove the hacked app.
Important: The app you need to remove is not necessarily the one named in the App Store alert. For example, the App Store may prompt you to update "Angry Birds" or "Twitter," but the hacked app may be something else entirely. Don't make any assumptions about which app you're looking for. To find it, you must carry out a systematic search with Spotlight.
Triple-click anywhere in the line of text below on this page to select it:
kMDItemAppStoreHasReceipt=1
Copy the selected text to the Clipboard by pressing the key combination command-C.
In the Finder, press command-F to open a search window, or select
File ▹ Find
from the menu bar. In the search window, select
Search: This Mac
from the row of tokens below the toolbar. Below that is a popup menu of search criteria, initially showing Kind. From that menu, select
Other...
A sheet will drop down. In that sheet, select
Raw Query
as the criterion, then click OK or press return.
Now there will be a text box to the right of the menu of search criteria. That's where you enter the raw search query. Click in that box and paste the text you copied earlier by pressing command-V.
The search window will now show all the App Store products that are installed. Compare those search results with the list of your purchases from the App Store. To see the complete list, you may need to unhide hidden purchases. If any apps were download from the App Store using other Apple ID accounts that you control, sign in to the store under each of those ID's and check the purchases.
At least one of the apps in the Spotlight search results is not among your purchases in the App Store. Move each such item to the Trash, after quitting it if it's running. You may be prompted for your administrator password. Empty the Trash.
Quit and relaunch the App Store. Test.

App Store says there is one update available. But the Updates page shows a blank screen. Have tried syncing with iTunes on mac

App Store says there is one update available. But the Updates page shows a blank screen. Have tried syncing with iTunes on mac as well. But nothing seems to work. Am using Iphone 5 6.1.4. Help

Next time that happens while on WiFi, turn WiFi off in settings, wait about 30 seconds or so, then turn WiFi back on. Sometimes you have to do this two or three times, but this fixes that issue as well.

App Store always shows Motion needs updating...

I've had this problem for months now. The App Store always shows Motion needs updating. But I have updated Motion (I check to make sure I have the current version).
I've ignored this problem up until now because Motion works fine and I do have the current version. I figured that sooner or later Apple would issue some fix, or that it would disappear on a future Motion or OS update. Well, I just updated to Mountain Lion yesterday, and I've updated Motion at least a couple of times, and the problem continues.
And now it's getting stuck in a loop showing I need to update to 5.0.7, even though I've updated. But now when I look in the update section of the App Store, it shows that it is possible to update (even though I have the current version). If I click "Update" again, it starts downloading and then starts endlessly installing it, but never finishes.
Any idea what's going on here? Any suggestions?
Thanks!

I did speak with Apple support last night. I uninstalled & reinstalled, and now I have the current version and it is working fine.
However, I'm still having the same problem I've been having for months: The App Store shows that I need to update Motion, even though I already have the current version. I don't know what is causing that, especially after I uninstalled and reinstalled.

NSURLErrorDomain error -1012 keeps coming up when I go to the app store to check for any updates.

When I go to the App store to check for any updates it will not proceed and gives me the following error message NSURLErrorDomain error 1012.
Can anybody help please.
Thanks,
Bernard

I am receiving the same error when I try to refresh the updates page but was able to download the Digital Camera Raw update without issue (this update was displayed on the page).
Have not tried the 10.9.3 update...
Curt

My Airport Extreme and Time Capsule both cannot do not mount my Seagate USB external hard.

My Airport Extreme and Time Capsule both cannot do not mount my Seagate USB external hard.
I am running OS 10.7.5
Both the TC and AE are updated to 7.6.1
The Seagate drive in formatted: Journaled HFS+
I tried everything on Apple's Article: HT1331 and the basic reboots and restarts.
"Next"

It sounds like you may be confusing "mount" with "recognize".
Connect the drive to the USB port on the AirPort Extreme
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit
Click the Disks tab
Does the AirPort Extreme "recognize" your hard drive? If yes, it will be displayed in the window.
See example below of a WD 500 GB drive connected to the AirPort Extreme.
If your drive is formatted HFS+ and it does not appear here, then you will almost certainly need to use a powered USB hub with the hard drive.....even if the hard drive has its own power supply. The USB port on the AirPort Extreme and Time Capsule is under powered.
Post back when the drive is "recognized" and we will next "mount" the drive.....although you likely already know how to do this.

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

AirPort/App Store/Time Capsule issues since update

Similar Messages

Maybe you are looking for