Airport Express with an Ethernet Network

I use a Ethernet connection at my house to connect to a LAN for internet access. i.e. no modem. Is it possible to use Airport Express with this network to create a wireless network?

I have a ethernet connection in my house which I use
to connect to a LAN. I wish to know if I can use this
with Airport Express to create a wireless network.
Yes you can.
I
have only seen documentation with the airport express
detailling a modem.
An Airport Express can be connected to an ethernet network as a wireless access point.
iFelix

Similar Messages

Airport express with an ethernet splitter

Hey,
I am thinking about getting an aiport express (802.11n) to connect my gaming consoles wirelessly as they are too far away from my router, and they are only 802.11g. Is it possible for me to get the AX set it up wirelessly to connect to my network on tc, and then run a splitter from the AX's ethernet port so that I could connect both consoles. On a separate note, this would put my AX in perfect position to use airtunes on my stereo setup, so if this would work it would seem like a perfect setup to me.
Thanks

That linksys device seems great if I were just wanting to set up my gaming consoles, but I was also hoping to use the airtunes that comes with it on my stereo setup. I don't understand why it wouldn't work if you were to use the airport express to extend the network through the ethernet, and then just split that ethernet feed to each console. It seems to me that I would really just end up using it as a router with the ethernet being how I got my internet connection to each console. Is there anyone out there that has done this, or something similar at least. Why would it not work if you were just to split the ethernet connection? It seems like that wouldn't affect the AX itself as it is just worried about getting the wireless data from the tc and then piping it through the ethernet connection.

Extend wireless airport extreme with airport express with through ethernet cable, extend wireless airport extreme with airport express with through ethernet cable

i want to extend my wirless range i using airport extreme upstairs and airport express down i have ethernet cable linking the two but airport express seems to go wireless and is extremly slow any help appreciated

Start with a "hard reset" of your Express - press and hold its reset button continuously, about five seconds, until its LED flashes rapidly. You will need to reconfigure all its settings.
Connect it to your Extreme with your Ethernet cable. Using AirPort Utility, configure its Internet Connection to "Connect Using" > "Ethernet" as in the following screenshot:
If it had been previously configured to "join" a wireless network and you connect its Ethernet cable to your wired LAN, you may experience what you are describing.

Airport Express with LaCie Ethernet Hard Drive

I have an existing airport express that currently is serving me just fine for wireless internet access (for mac mini, two pc laptops), print sharing and itunes.
I recently purchased LaCie's Ethernet hard drive. I am not able to use the usb port for to set the drive up - but was told buying D-Link Wireless G Router would do the trick and work in "tandem" with the AE. Anyone know how to figure this out? No problem using the AE for just print sharing and itunes - but does anyone know if this can be done? I would like to hook up the ethernet drive and possibly a Tivo but am limited w/ the Airport Express. At the same time, I don't want to replace the benefits of having the AE and do not need it to necessarily extend my network either.....

Well...I did just that - bought a D-Link 4-port router and hooked everything up. I disabled the AE router and have not been able to find the drive at all on any of my wireless connections. However, when I hooked up an ethernet cable from my laptop (pc) directly to the new router - i was able to see drive and access the login dialog box.
After having to reset the AE - and reestablishing the wireless network and checking all connections - I still had no luck. My wireless internet connection was working just fine so it appears that this setup is close to working - but still no recognition of a ethernet drive. Any ideas? Thanks.

Trying to set up Airport Express with Ethernet Powerline adapters

Hello,
Having some problems trying to set up my Airport Express with Netgear ethernet powerline adapters.
I want to set up as follows:
Wireless Belkin router --- powerline <---> powerline --- airport express --- home stereo system
The problem I have is that I can connect the airport x in client mode & wirelessly play music using airtunes (until the sound breaks up) but itunes does not find the airport x when connected via the powerlines.
I have airport admin utility configured as follows:
Airport tab:
Wireless mode: create a wireless network
Wireless network name: same as my wireless router SSID
Allow this network to be extended: unticked
radio mode: 802.11n (802.11b/g compatible)
Channel: automatic
Wireless Security: WPA/WPA2 personal (as per my router)
Wireless Password: as per my router
Verify Password: as per my router
Internet tab:
Connect using: ethernet
Connection sharing: off (bridge mode)
Music tab:
Enable Air Tunes ticket
no password set
In iTunes, I have home sharing on & share entire library selected with no password set.
Using OS 10.6.5 & Airport Express 7.5.2
I can ping the IP address of the airport express when connected via the powerlines but cannot select the speakers in iTunes (they are greyed out).
Any assistance would be appreciated....
Thanks

Hi,
Thanks for the quick response...
As suggested, I connected up the Airport X to the Belkin and plugged in a pair of headphones. It didn't work, still could not select the Airport X as speakers.
Dug out my old Netgear DG834G and connected that up in place of the Belkin - it worked. Next connected in the Netgear powerlines and it still worked.
So, the problem is the relatively new Belkin F7D4401 router.
Looks like I will have to find an alternative 802.11n...
Thanks for your help.
Regards
Simon

AirPort Express/Time Capsule WDS Network - will this work?

Have recently bought a Time Capsule but realised that it won't do what I want with my Linksys ADSL wireless router. I think I understand how to make it work with an AirPort Express, but would appreciate it if someone could confirm my ideas before I buy even more hardware!
My situation is that my ADSL line comes in to the house on the ground floor. There's no extension phone sockets and I don't want or need them. My home office is on the first floor.
What I want is to have my ADSL modem and a wireless device on the ground floor, the Time Capsule in the home office with mac and XBOX making wired connections to it, and a USB printer also connected.
If I get a DSL modem and then connect an AirPort Express to that, can I then set up WDS so that the Time Capsule becomes an extension of the WLAN and I can connect the devices to the Time Capsule via wires? Or do I need an AirPort Extreme to do this instead of Express? Or is it just plain not going to work?
Thanks in advance for any advice!

I am using a Time Capsule with an 802.11g Airport Express with a WDS network. In my case the Time Capsule is the main device and the Airport Express is the remote device, but I'd think it would work the other way. Just make sure you're using "Airport Utility", not "Airport Admin Utility" to configure it.
One other thing: I found it easiest to reset both devices to factory default settings and use the Airport Utility wizard to set up the WDS network on both devices. Good luck!
My network:
DSL ]--[ Time Capsule )))((( Airport Express

Can I add a second Airport Express using an Ethernet cable to extend my network if the first AX is wirelessly connected to an Xtreme?

Hi, I run a small motel and I am trying to extend the wireless network from the office to the rooms in the next building.
I have an AirPort Xtreme connected to my router with an ethernet cable and it works fine. I have then connected an AirPort Express to this in the next bulding wirelessly (as i cant run an ethernet cable outside) which extends the network over all but the last 2 rooms in the next building. There are bick walls so it sruggles over the distance. I realise I cant connect another airport express wirelessly to extend the network further but can I connect another Airport Express using and ethernet cable to the exisiting Aiport Express to extend the network that extra distance?

You can do this, but as you might imagine, that is going to place even more of a load on the weakest link....the wireless "hop"......between your AirPort Extreme and the current AirPort Express.
So, things will slow down even more. Whether or not that will be acceptable to your guests is open to question. Light browsing and email should be OK. Someone trying to download a large file is going to be waiting longer than they might consider normal.
Things like this, you simply cannot predict in advance. Might be a good idea to understand the store's return policy if the new Express puts more of load on the network than is expected.

Airport express with wired network

Hello,
I am looking to play my itunes library through my receiver in my living room. There is an ethernet connection there. My mainMac is in another room, also connected to the network. Can I just connect the airport express with airtunes to an outlet in the living room with the ethernet wire into it? (and then the receiver connected to the audio out, of course) My mainMac does not have a wireless card.
I would appreciate some help. Thanks.

ok, so I bought the AX because it seems that I should be able to do what I want. I plugged it into my network, but when Airport Admin Utility tries to scan for AX, nothing shows up. Any clues?
Thanks,
Mario

I have just changed my network provided and now i can't find my 1st gen airport express with airport utilities

Hi, can anyone help. I've just updated my network with a new hub and now i cant find my 1st gen Airport express with the curreent Aiport utilities.

From your description, it sounds like the AirPort Express was configured to connect to your "old" router or hub...and, to do that, the Express remembered the specific ID of that device as part of the connection credentials.
The Express is likely still looking for the "old" device for which it still has the settings to connect.
Since you changed to a new hub or router, the Express has no idea how to connect to this new device.
If this is the case......then the solution will be to reset the Express back to factory default settings....and then configure it again to connect to your "new" hub.

Trying to get my Viera TX-P42S30B hooked up to me home network via Airport express with no luck.

Trying to get my Viera TX-P42S30B hooked up to my home network via Airport express with no luck.
Have tried both wired (network cable) and wireless to no avail, can't find much info online, any help appreciated !
Airport utility 5.5.3
Airport Extreme 802.11n
Airport Express 802.11g

The problem is that the AirPort Express (AX) is creating a subnet.
To prevent that, configure the AX to act as a bridge (so that it is NOT sharing a single IP address).

WDS with Airport express and Dual ethernet Airport base

Can the airport express and dual ethernet airport base create a wds? I can't find the options on the airport base's software.

coloradoapple, Welcome to the discussion area!
The Dual Ethernet (snow) AirPort base station (ABS) does not support WDS.
Only the AirPort Extreme base station (AEBS) and AirPort Express (AX) support WDS.

How to Connect Airport Express to Existing Wireless Network (Client Mode)

I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
So here's the situation:
Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
Do yourself a favor, toss that user manual aside and run these steps.
(Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
Some pointers:
- When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
- I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
<Edited by Moderator>

Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
Thanks

Airport Express no longer joins network

Greetings, I have a cable modem internet connection; I use an older Airport Extreme (802.11n, without Time Capsule) to make a local wifi network with WPA2 Personal security, and an older Airport Express (802.11 b/g, firmware 6.3) to connect a laser printer in a different room.
All was working well until two days ago when access to the internet disappeared. I reset the modem, confirmed that the cable connection was working by plugging a laptop directly into the modem by ethernet, determining that the problem was the Airport Extreme. I discovered the 7.5.2 firmware update which I uploaded, and all seemed well.
However, the 27" iMac upstairs only connected to Airport intermittently; it appeared to have been duplicated in name, as well as only recognized the Airport Express. I've since been able to correct that problem, however, now the Airport Express no longer connects to the Airport Extreme network.
I've tried soft resets (unplugging then plugging back in) and hard resets (pressing the reset button with a paperclip until the amber light flashes, then reconfiguring the device). I've tried setting the Airport Express both just to join the network (printer sharing) as well as extend the network; I also reverted the Airport Extreme's firmware to 7.4.2 which works perfectly well. However, now after each successive attempt to reconfigure the Airport Express to join the network, Airport Utility says that the Airport Express has been successfully updated and will restart, which it never does - it simply flashes an amber light, and Airport Utility eventually times out and says that it was unable to find the Airport Express after restarting, noting that the settings have been successfully updated, but that there is a problem re-joining the wireless network/finding the device. Notably, the Airport Express no longer appears in the left hand list of wireless devices in Airport Utility.
Help!!

Hi pslebow,
You make it sound like there was no change, then suddenly the Airport Express 802.11g lost connection to the wireless network and you can't get it back.
What network security is your wireless network using?
From the specification sheet, "…When joining an existing wireless network, AirPort Express only supports WPA-Personal."
AirPort Express - Technical Specifications
Please make sure your router security is set to match.
iOS and OS X: Recommended settings for Wi-Fi routers and access points - Apple Support
If you have older Wi-Fi devices on your network that don't support WPA2 Personal (AES), a good second choice is WPA/WPA2 Mode (often referred to as WPA Mixed Mode). This mode will allow newer devices to use the stronger WPA2 AES encryption, while still allowing older devices to connect with older WPA TKIP-level encryption. If your Wi-Fi router doesn't support WPA/WPA2 Mode, WPA Personal (TKIP) mode is the next best choice.
Best,
Nubz

Airport Express with printer & hard drive with Time Machine

I have a MacBook that I'd like to backup its data. Concerned about the following (in level of concern from highest to lowest): theft, crash, fire.
I currently have an Airport Express with a Brother printer attached to it that my PC and MacBook print to.
I am really in a dilemma as to what to do. I was looking into Carbonite to get an offsite backup location of my data. (I figured offsite would cover all concerns of losing data due to theft, fire, or just a crash) However, Carbonite does not hold onto data you delete (ie, my photos and videos will fill up my hard drive eventually and I'd like to just archive them in one central spot when I am done accessing them on a regular basis-- ie delete them off my MacBook hard drive). That is like $55/year to do Carbonite... but, the only thing that will help me with over a hard drive in my house is a fire (and theft if a burglar were to find where my backup drive was in the house).-- Of course, I'd probably want a different location for my hard drive for that reason -- so, I'd have to buy another airport or just a time machine that has the wifi built in.
I've read lots of issues with the Western Digital trying to download programs onto your computer... I have one for my PC that I backed up photos manually and it did try to install programs when I attached it to my PC... not so much my Mac when I took some photos off it. I looked into getting another portable hard drive at Costco for my Mac, but realized that it would require reformatting to use on my Mac (as it was built for a PC).... something I wasn't sure if I was computer-savvy enough to do or if I did do it, would I end up with issues later on?
Anyhow... in the end, what do you all do to backup your data, especially photos and videos? Do you have smaller hard drives that you back up to and then when full move them to an offsite location? Can you have more than one "hard drive" backing up..... I was thinking it would be nice to have one larger hard drive that would potentially hold all my photos and videos so I can access anytime, but then have smaller drives of the same data that I can take to a safe deposit box and use as my super secure backup (no fire, no theft, no crash).
btw, When doing time machine, does it keep all the metadata with each photo?
Burning CD's is time consuming.... and, I have heard there are different qualities of disks out there... archival v. not... how long do the archival last v. the non-archival... or is that more of an issue for future generations not being able to access our photos?

You need to remember that the Time Capsule is both a wireless router and a hard drive all in one enclosure. If you don't need a wireless router, around $150 of the $300 for a Time Capsule is going to be in the router portion of the device.
The nice thing about the Time Capsule is that it is a network drive. All Macs running Leopard or Snow Leopard will be able to back up automatically to a single device. The first generation of Time Capsules about two years ago had some power supply problems that affected some users. Apple announced a program for these users to replace their Time Capsules.
So, it depends on your requirements. If you are looking for a new, dual band wireless router and want to backup your Macs running Leopard or Snow Leopard automatically using ethernet or wireless, the Time Capsule is a logical choice.
If you don't need a new router, then you'll need to look at a separate hard drive that will be attached directly to the computer using the USB or FireWire port. If you have two Macs, you'll have to get two hard drives if you want to do Time Machine backups correctly.
Most hard drives can be reformatted to work with Mac if you don't mind a few extra steps and Disk Utility (Macintosh HD > Applications > Utilities > Disk Utility) does not look too complicated for you.
Message was edited by: Bob Timmons

How do I install a new airport express and link a second airport express to extend the network of the first airport express?

I currently have a linksys wireless router attached to the Internet. I have an A1264 Airport Express connected by Ethernet to the linksys router. I have two network names, one for each wireless network.
I purchased a new A1392 Airport Express to replace the linksys router and join to the A1264 Airport Express, and I want to have one network name as a result.
How do I do this? I realize that I have to reconfigure the A1264 device so that it is an extension of the A1392 device.

You have a fairly complicated set up, so I suggest that it would make sense to tackle things in stages, testing each stage as you go, before proceding to the next stage.
Stage 1 would be setting up the A1392 first to the cable modem, and then making sure that everything is working correctly on the A1392 Express
Stage 2 would be adding the Netgear switch and testing each port with a laptop connected via Ethernet to make sure that everything is operational on the switch
Stage 3 would be connecting the A1264 Express and testing to make sure that it is extending the network correctly
Stage 4 would be adding other Ethernet devices to the Netgear switch and testing each one at a time before adding the next device. There is some question about whether an iOS device can print to an Ethernet connected printer....even if the printer is AirPrint compatible. You may need to connect the HP using wireless...not Ethernet....to gain full AirPrint functionality, or use another application that will allow printing like Printopia or Print Central using the Ethernet connection on the HP.
Stage 5 would be adding the printer to the A1264 AirPort Express.
You do not mention how the printer will connect to the A1264 Express, but I assume that it will be USB from your description. Most printers will work, but you really will not know if your printer will work until you try.
Remember that only printing will be supported at the USB port of the Express. If you have an all-in-one type device, scan, maintenance, and other advanced features will not be operational whent the device is connected to the AirPort Express.
If you want to print from an iOS device like an iPad or iPhone, plan to add additonal software like Printopia or Print Central to possibly allow this function. There are no guarantees here as far as the iOS devices.

Airport Express with an Ethernet Network

Similar Messages

Maybe you are looking for