Anyway to dual boot either Linux and Mac OS X?

Is there a way to dual boot Ubuntu and Mac OS X similar to Boot Camp?

Here's where you start.
As an alternative you can purchase either Parallels Desktop for Mac or VM Fusion which provide virtual machines in which you can run various operating systems concurrently with OS X. Both products run various versions of Windows, Linux, and Unix.

Similar Messages

Dual-Booting Arch Linux and Windows 7

Hello,
I am attempting to set up a dual-boot configuration with Windows 7 (installed first), and Arch Linux. When I went to install, I read in the documentation that the AIF doesn't support installing GRUB to a separate partition other than the MBR on the drive. I want to install GRUB separate from the Windows MBR so I can use Easy BCD to chainload the two bootloaders (i.e. installing GRUB on /dev/sda5 instead of /dev/sda). I went through the installation process and tried to install GRUB manually via the instructions given in the documentation. But when I went to boot Arch, I was greeted with the GRUB shell instead of the boot menu. What did I do wrong? And is there any easier way to install Arch this way given that I do not want to overwrite the Windows bootloader? I went ahead and wiped the Linux partitions on my drive, so I am going to do the install again once I have some suggestions.
Thanks!

joshuawagner147 wrote:
hyperreal_logic wrote:
To the original poster:
If you want to chainload both Windows and Arch Linux using your preferred boot manager, you'd have to create a separate 'boot' partition when installing Arch Linux. When you are in the Arch installation, create a separate partition of about 500 MB, then create the root partition of whatever size you need, and then create swap partition if necessary. So your HD would resemble something like this: /dev/sda5=boot partition of 500 MB; /dev/sda6=root partition of ## MB/GB; and /dev/sda7=swap partition of (RAM * 2) GB. Then continue with the Arch installation procedure until you get to the end where you are prompted to install a boot loader. Choose GRUB, and install it to the 'boot' partition on /dev/sda5. This will allow you to chainload Arch via Easy BCD. What happens is Easy BCD will pass the message to GRUB on /dev/sda5, and GRUB will then load your Arch root system on /dev/sda6.
I hope this helps. I support your choice in using Easy BCD to chainload Windows and Linux. Software is, after all, about choice. Furthermore, you've presented a good reason to use Easy BCD as the main boot loader, which is to save you from unnecessary tinkering with the GRUB shell or Live CDs and whatnot. However, if you don't want to create the separate 'boot' partition, then you'll have no other choice but to use GRUB or syslinux on the MBR.
Thanks. Yes...I followed the procedure just like you described. I figured that my problem was that I didn't create a separate /boot partition, so I reformatted the partitions I created and redid the install. However, I was not able to install GRUB in the AIF; I had to reboot into the Live CD and install GRUB to my boot partition manually. All is good now as I have a working dual-boot now. Arch Linux has been a sort of learning curve for me, but I have gained valuable knowledge and experience by using this distro.
Yes. I didn't want to mess with GRUB or NTLDR. I know that reinstalling NTLDR is not that difficult, but I didn't want to mess with it at all. It just seemed easier to chainload GRUB to NTLDR using EasyBCD. I'm a sort of "distro-hopper" anyhow, and using this method allows me to cleanly remove any distro I install without having to mess with GRUB or reinstalling NTLDR.
Thanks!
Glad to hear! Yes, Arch Linux is a wonderful distribution, and one of my favorites. It's great for not-so-newbie beginners to learn from. pacman is one of my favorite package managers, as there is always the latest stable software available in the Arch repos. Glad everything worked out. Have fun with Arch!

Dual Booting Ubuntu Linux and Windows on a RAID 1 setup

Hi,
I just bought a Lenovo W530 with Windows 7 and two 500GB hard drives in a RAID 1 setup, is there a way for me to install Linux with dual boot while maintaing my RAID 1 setup?
Thanks.

Hi
Welcome To Lenovo Community
if you want both in a raid on two drives, there is no way simpler than using fakeraid.
Windows simply has only the fakeraid as a software raid and can't be run from a linux software raid. An Ubuntu 10.10 install to fakeraid is relatively simple but should not be undertaken without some understanding of what a raid install looks like or behaves.
As a starter, some simple rules have to be followed:
1) Install Win 7 first
2) If Win 7 occupies the whole raid drive, use Win 7 disk manager to shrink it to make room for Ubuntu.
3) Use gparted on a live cd to place all your unallocated space for installing Ubuntu into an extended partition. This will insure that you will not likely exceed the 4 primary partition limit and thus bar an Ubuntu install.
Once prepared as above you should be able to install Ubunto to the largest unallocated space, as long as the partitioner recognizes the raid (ie the win 7 partitions will show in gparted). You should plan to run the install from the live cd so that you have determined beforehand that 10.10 will run on your system.
http://ubuntuforums.org/showthread.php?t=1600991
Hope This Helps
Cheers!!!
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
How to send a private message? --> Check out this article.
English Community Deutsche Community Comunidad en Español

Dual boot arch linux and windows

I recently installed arch linux. However, I have a windows 7 installation on a separate hard drive (/dev/sdb), and it is not detected by grub. I have tried to use os-prober, and grub-mkconfig to generate my configuration file, but I think these programs are in grub2-common, and this conflicts with the package grub. When I do uninstall grub, and replace with grub2-common, I can generate the config file, but grub brings me to the grub prompt, and will not boot. Can I use grub-mkconfig without uninstalling grub, or do I have to create grub.cfg and edit it manually? Thank you in advance!

skunktrader wrote:
grub reads /boot/grub/menu.lst. You need to edit this file manually to add windows 7
Read this
It works! You are a genius!!!!!!! Thank you so much!!

DUAL BOOT windows 7 and linux HELP with Current info on BIOS, MBR vs GPT, etc

I have a feeling this should be easier than what I'm making it. Please educate me on Lenovo's BIOS Setup menus, etc.
I have installed easyBCD in Windows 7, and plan to use it to set up my new boot menu with Linux Mint (and possibly other distros).
I am using a live DVD. I inserted the DVD and went into SETUP and selected to boot off the DVD drive. It started to boot into Linux and all was going well.
However, I realized that I had not checked on the Secure features (Secure Boot, EFI). So I shutdown again and went into BIOS. I went to the SECURITY menu and Disabled UEFI. Then I disabled Secure boot.
Tried to boot off the DVD and couldn't get anywhere. Kept putting me back into the window to select the boot device over and over again. THought I'd ruined my machine
Anyway, finally stumbled upon STARTUP menu, and put it into EFI Legacy, and I was able to get back into Windows 7.
Obviously before I pursue this further, I need some educaiton on your MENUS, Lenovo and EFI/Secure Boot.
I have a feeling that I can probably now install the Linux but want to make sure my settings are correct before I pursue.
Thanks, Kim
Moderator note: this thread gets more Linux-flavored with each post Moved from the "T" board to the Linux board.

Hi, thanks for ans. Your specs are almost identical to my T530 ,which I should have listed. The only diff is
I have an i7 35something processor. Same intel card, RAM and HDD, not that that should matter I'm guessing.
I purposely avoided the Nvidia card because of all the heaadaches with Nvidia.
I have to teach a class tomorrow and I need to clean up my notes. (Definitely not computer related...LOL.) I don't want to be stressed out about this during class, so I plan to wait to attempt a new install tomorrow afternoon.
What I have done is find out some more info about dual booting with windows 7. I went in to windows 7 to shrink the C: partiition and it said I'd have to reserve at least 220 GB for MS! Not what I wanted; I don't really care a thing for MS. I was born and raised on Unix and Linux; I never really fiddled with MS after the demise of MS-DOS during my college days.
Given that, and the fact that I'd lose half my 500 GB HDD to the Borg, I may just chuck the entire dual boot thing and just load Linux on it.
If you say you're running Linux on it just fine, that would be a great encouragement. No HW problems at all? Everything working fine? Which distro are you using?
I plan to test Mint, Fedora, PCLinuxOS, Mageira (sp?), saybahon (sp again?), Debian Wheezy, and even Pear, LOL. I'll keep trying till I find a distro to run on my Lenovo T530, but I'm guessing all of 'em should do okay.
I have Lubuntu I could give a spin, as well and Crunchbang and Bodhi, but they're all 32 bit. (I have an antique Dell desktop that I still use down in my woman cave.)

Dual Boot Windows 8 and Linux?

I have (UEFI System) an ASUS K55A UEFI motherboard laptop that came factory with Windows 8. I would like to install backtrack linux and Windows 8, but before I go screwing up my laptop, I want to see if this would be at all possible. I would use a virtual
machine, but I need Backtrack Linux on a physical machine for testing purposes as I am taking a course in computer forensics, and I want to test cracking my home wi-fi. My processor is an Intel Core i5 2.5 ghz with a 500 GB HDD and 8GB DDR3 RAM. Any insight
on this would be appreciated. Thank You.

Hi,
You can refer to this article to get detail information.
http://apcmag.com/how-to-dual-boot-windows-8-and-linux.htm
Niki Han
TechNet Community Support

Dual booting Windows 8 and Arch Linux with UEFI

Hi all!
I'm trying to install Arch Linux on my computer where I already have Windows 8, and I'm getting a little stuck when it comes to the partitioning.
Following the beginner's guide and the method here: https://wiki.archlinux.org/index.php/Un … n_in_Linux for setting up the partitions properly, regarding UEFI. My problem is that when using cgdisk to set up a new EFI system partition (ef00), I get an error message when trying to write the partition table (just saying that something went wrong). I figure the problem is that I already have a partition like this (correct me if I'm wrong), but it really looks like it succeded (see info below). So my question is: How do I preceed to keep my Windows 8 installation happy, but installing Arch? Do I remove the old EFI system partition and create a new one, or is there some method that allows me to edit the already existing one, to allow me to dual boot Windows 8 and Arch?
My partition table now looks like this:
Part. # Size Partition Type Partition Name
1007KB free space
1 500MB Windows RE Basic data partition
2 300MB EFI System EFI system partition (this one was already present on my system)
3 128MB Microsoft reserved Microsoft reserved partition
4 63.5GB Microsoft basic data Basic data partition
8 512MB EFI System EFI System partition (this is the one I tried to create when I got the error message)
5 29.5GB Linux filesystem Arch (this is where I was going to put my Arch installation)
6 22GB Windows RE Basic data partition
7 1024MB Windows RE Basic data partition
615KB free space
Just for the record; I only created partition #8 and #5.
Any help is appreciated! And sorry for beeing a total noob, but I really suck at this.

sudo make sandwich wrote:If it is possible to share ESP between OSes, how do I do this (would it be sufficent to follow this section: https://wiki.archlinux.org/index.php/Beginners'_Guide#For_UEFI_motherboards)?
There's really very little to do to share an ESP between OSes. Most OS installers will auto-detect the ESP and use it. Problem solved. For Arch it may be a bit more effort just because Arch uses a more hands-on installation process, but I've only done a couple of Arch installations, and the last one was several months ago, so I don't recall the details clearly enough to comment.
And how big will the partition need to be? The beginner's guide says 512MB or higher.
I don't know what was in the mind of the author, but my guess is that's because that's roughly the cutoff point where mkdosfs starts creating FAT32 by default rather than FAT16. The ESP is officially supposed to be FAT32, not FAT16, although FAT16 usually works OK. It's also possible to create FAT32 on smaller partitions by using an explicit option to mkdosfs ("-F 32").
The optimal size of the ESP depends on the files stored on it. If you don't store your Linux kernels, something as small as 100MiB is usually adequate; but a few Linux kernels and their initrd files can consume twice that amount. My own recommendation is for the ESP to be 200-500MiB.
The only error message I got from cgdisk is "Problem saving data! Your partition table may be damaged!", however booting Windows again works fine. Parted did not complain about antything.
Use the "verify" function in cgdisk. That will reveal any problems with the data structures. If a verify turns up OK, then that means that cgdisk ran into some sort of disk problem. Running gdisk rather than cgdisk and using the gdisk "w" option (without making any changes) may produce a more helpful error message.

Dual booting in Windows and Linux, but only Linux has calendar, TB 31.0

I'm dual booting using Linux Mint and Windows 7. I have TB 31.0 installed in each OS. TB in Linux has calendar capability; in Windows, there's nothing (by nothing, I mean no calendars - I can't see their properties, for instance, nor access them in any way).
I should add that both Windows and Linux TB programs are sharing the same profile folder (located on a separate partition), hence, all the same add-ons, passwords, etc.
The error console logs the following:
Timestamp: 14/08/2014 6:41:33 PM
Error: Components.classes[cid] is undefined
Source File: resource://calendar/modules/calUtils.jsm -> file:///P:/PortableApps/ThunderbirdPortable/Data/profile/extensions/%7Be2fda1a4-762b-4020-b5ad-a41df1933103%7D/calendar-js/calUtils.js
Line: 17
There are a variety of flow on errors, related to this.
My apologies for posting this in this way; I had intended to submit this via the crashreporter, but I'm having trouble getting the program to crash with this error just now.

A reply to my own question: it turns out that while sharing a profile works pretty well for most purposes, with Lightning it does not, as the extension has different Linux and Windows versions. The problem is solved quite simply: by not using the same profile for each version.
Glad to see that no one wasted time on this one (except me, of course).

[SOLVED] Dual boot windows 7 and arch Linux with seperate hard drives

Ok so I'm stuck trying to get my computer to dual boot windows 7 and arch. They are installed on different hard drives and I have grub 2 as the boot loader. I can't find any tutorials on how to do it with seperate hard drives I know how to do it if they are on the same hard drive. Also I want windows on the "first" hard drive how do I check to see which one it considers the first?
Last edited by bdawg (2012-09-21 23:15:37)

DSpider wrote:
drobole wrote:If you want to change it so that sda becomes sdb and sdb becomes sda, you should be able to do that in BIOS.
Not from the BIOS. He would need to physically open up the computer and switch the cables between them (or add another drive).
There's no actual performance increase in changing this order. Performance increase is when you have the partitions as close to the beginning of a HDD as possible, where the platters spin faster (basic mechanics, not to be confused with CD/DVD, which are being written from the inside-out to prevent errors after extended usage), and it especially doesn't apply to SSDs whatsoever.
You may be right about that. I remember I had to do this a while back but I probably switched the cables. It also messed up the drive mapping in Windows 98 if I remember correctly.

Dual boot for lion and SL

BHow do I set up the dual boot for Lion and snow leopard oon the same internal hard disK
What does Time machine do under the dual boot?

I am also considering putting Lion and SL on separate hard drives.
Since this is an iMac forum, I assume you will use an external drive as the second drive. Use one that connects via firewire, not via USB.
Both on a single drive -
OK. Doing it on a single drive means you will need to partition the internal drive. Although this is straight forward, it is always best to back up the existing drive first, just in case. It's a good idea to have a backup on a different drive, anyway.
To do that, clone the entire internal drive to the external drive.
I would suggest, though, that you first partition the external drive. I would suggest four equal-size partitions, provided the drive is big enough - at least 1.0TB, though a 2.0TB drive might be better. You can use OS X's disk utility to do that. Go to the Partition page in Disk Utility, select your external driv in the list on the left, then use the Partition Layout menu to select the number of partitions. Set the format to Mac OS Extended (journaled) GUID for all partitions. Click the Apply button.
The easy way to do the cloning is to use a cloning utility such as Carbon Copy Cloner. Clone the entire internal drive to one of the partitions on the external drive. Then test boot to it (use Startup Disk in System Preferences to do that) to verify the integrity of the clone. At that time I would suggest you change the background design/picture for the desktop to aomething other than the one used on the original drive - this can be a handy visual reminder of which volume you are booted to.
Then add a partition to the internal drive. To do that, run Disk Utility. Go to the Partition page, select your internal drive in the list on the left, but do not use the Partition Layout menu this time. Instead, click the existing volume in the graphic display, then click the plus ("+") button underneath that display -
This will add a partition without erasing the existing information - i.e., the drive will end up with two partitions, one of which will contain your original boot volume.
Use Startup Disk to re-select your original boot violume, and restart back into it.
Now, clone the original drive again using CCC, but this time to the second partition of the internal drive, the one you just added.
Boot to that freshly cloned volume to verify it. Then, while still booted to it, install OS X 10.7 Lion onto it.
This will result in your original Snow Leopard on the first partition of the internal drive, and Lion on the second partition of the internal drive.
The external drive will have Snow Leopard on one partition, one partition will be empty (available for a clone of Lion if you wish, or use it for extra storage). The remaining two partitions can be used for Time Machine backups - one for Snow Leopard, one for Lion.
If you want to have each OS on its own hard drive, then you can use the first clone of Snow Leopard to the external to be upgraded to Lion, or upgrade the orignal on the internal drive to Lion. Be sure to boot to the volume to be used for Lion before installing it so that Lion is installed onto the correct boot volume.
You can then use the empty partition on the internal drive as the backup (or Time Machine) volume for the OS on the external drive, and vice versa. In this arrangement you may need only partition the external into two volumes.
If you have a different scheme in mind for partitioning, feel free to do that. I don't use Time Machine, so don't have the need to make space for it. Carbon Copy Cloner can be used to do incremental backups after the initial backup - but I don't use that, either. I'm old school - after the inital cloning for backup, I do manual backups of files on the fly.
Comments -
* I would suggest keeping both Snow Leopard and Lion on the internal drive. Reason - even though firewire 800 is fast, it is still noticeably slower than an internal drive. OS's on an external drive will run slower than those on an internal drive.
• I don't like the concept of Time Machine. Amongst other things, it seems to want more space on the target volume than it actually needs; and it is not a bootable replication. A clone of a bootable volume is bootable.
• It was just a few days ago that I went through the same process as you are planning. One slight difference - I used a 1.0TB external partitioned into 3 equal volumes, since I had no need to allow space for Time Machine. I have Snow Leopard and Lion each on its own partition of the internal drive; and cloned backups of each on the external drive, plus one GP partition on the external drive.
• If you have not yet downloaded Lion, be prepared for it to take a while; it's almost 4GB in size. Probably be a good idea to defeat sleep for the duration.
• Cloning takes a while, but not that long - it took 30 minutes to clone 45GB to the external drive, and 45 minutes to clone it to the second internal partition.

Tutorial - How to triple boot OSX, Linux and Windows 8.1 with a shared Data Partition without any third party Win / OSX softwares

This is not a question, but rather a personal guide that has proved to be running successfully.
I would like to thank numerous sources, including Christopher Murphy's suggestions at:
Re: Repairing Boot Camp after creating new partition
Before proceeding, there are certain concepts needs to know:
Why Boot Camp does NOT allow further partitioning of drives after Windows has installed?
Answer: Because the way Apple configures the Mac to be recognized as non UEFI capable system on Windows.
Quote from Christopher Murphy based on the above line:
However, Windows on Macs right now use CSM-BIOS mode in Mac firmware that presents BIOS to Windows rather than EFI. Windows thinks it's on a BIOS computer, and therefore mandates the use of MBR for boot disks, rather than GPT. So that's why we have this hybrid MBR+GPT approach on Mac with Windows on it. You inherit the limitations of MBR, which is four primary partitions.
So what does it means?
It means that OSX + EFI + Recovery HD + Boot Camp partition = 4 primary partitions and thus any attempt to modify the disk will render booting issues of either system.
For more info on GPT (GUID Partition Table disks VS Master Boot Record or MBR in short, you may visit: http://msdn.microsoft.com/en-us/library/windows/hardware/dn640535%28v=vs.85%29.a spx)
So, how to overcome it?
The general guideline is to install ALL GPT ready OS first then create a Data partition, before installing Windows (Which is again, NOT supported GPT due to EFI configuration by Apple where end-users are not able to modify it).
Interestingly, since Mac Pro 2013 Late supports only Windows 8 and above, thus it is not known if this CSM-BIOS applies to it or not.
Do take note that GPT disks in Windows can only be booted when the system meets the 2 requirements:
http://msdn.microsoft.com/en-us/library/windows/hardware/dn640535%28v=vs.85%29.a spx#gpt_faq_win7_boot
1) Windows x64 version (Which is a must for newer Macs. If you cannot go to Boot Camp 5, then you need Windows 7 x86 or 32bit version)
2) UEFI system. However, Windows sees all Macs (With the possibility of Mac Pro 2013 Late is an exception. To be determined) as BIOS, or rather NON-UEFI system.
In short, booting on GPT disks is not possible for Mac in Windows.
Summary,
It is tested that a combination of the following will not work:
- OSX + Windows + Linux
- Windows + OSX + Linux
- Windows + Linux + OSX
Usually it can create the system un-bootable or OSX refused to install due to the system does not recognize such partitions and / or Disk Utility refused to format a free space. An example screen-shot is provided below:
The error message is shown as
Title: "Failed to erase volume" Message: "Failed to wipe volume, as an error occurred: MediaKit has reported that the device does not have enough free space to execute the requested operations."
The second thing is about the preparations we need.
1) 1X Windows 7 or 8 DVD or USB thumbdrive
1A) If you uses a DVD to install, you will need another thumbdrive to load the BootCamp drivers for Windows as well as may requires an external DVD drive for newer Macs
2) 1X Linux DVD of your choice. Personally I choose Fedora 20.
So ready? Let's go.
1. Using Disk Utility, shrink the OSX's partition size to what is needed. For me, I give OSX 150GB. Do NOT create any new partition.
Disk Utility should see something like below whereby only OSX partition is left with desired disk space. The remaining space are to be unused disk space for the moment.
Note: Click on the top most item that should start with the size of your HDD / SSD. Then clicked on "Partition" and specify the desired OSX size. Hit "Apply" after that.
2: Download Boot Camp drivers only via Boot Camp Assistant. The USB thumbdrive shall be used later after Linux's installation.
Boot Camp Assistant should see this:
I have only selected "Download latest Windows Support Files from Apple"
3. Insert Linux DVD, reboot Mac into EFI mode (The left most first "EFI mode").
Note 1: Before rebooting, please plugged in an Ethernet adapter because Wi-Fi drivers is not installed.
Note 2: For Thunderbolt adapters, it must be plugged in before reboot as hot-swapping is not supported under Linux. More on the tips at the end of this article.
Note 3: Press and hold "Option" after the screen turns black. Release Option key after you see the image as below:

For the unfortunate part that did not make it on time to edit the images:
9. Install the Windows Support software from your CD/USB drive to gain full functionality of your computer. Reboot and go to Windows again.
Note 1: You may choose to eject disc at this point of time. For Apple SuperDrive users, you will need to wait until the drivers (i.e. Boot Camp support files) is installed and rebooted before ejecting is reasonably possible (As I failed to figured out how to right click without the drivers)
Note 2: Unlike Windows 7 on KBase article TS4599 Keyboard/trackpad inoperative, black screen, or alert messages when installing Windows 7, USB stick can be plugged in after the Windows installation is done. This is because Windows 7 (And probably Windows 7 with SP1 DVD) does not have a built in USB 3 drivers when it was released back in 2009 where USB3 has not arrived then.
Note 3: Due to TPM, Bitlocker is not supported without the use of thumbdrives.
10. Using Disk Management to determine the given drive letter for the DATA partition (DO NOT DELETE and RECREATE partition or else you can goodbye to booting Linux and OSX). Disk Management will not allow you to format it as exFAT / FAT32 in graphical way.
Note: You may remove or modify some of the disk letters in Disk Management. However, do NOT remove / modfify the drive letter for the partition with 200MB size in HFS. This is because it will disallow booting of Linux and neither could Windows nor OSX can do anything EXCEPT to reinstall Linux only.
11. Open Command Prompt in Administrator Mode (Important!!), and key in the following command:
format F: /FS:exFAT
Give this volume a label after it has successfully formatted before hitting "Enter" again.
Note: Mine Data partition was assigned as F drive. Please make necessary adjustment to "F:" should your Data partition is assigned to other letters.
12. After that, Setup your Data partition structure as you like.
Tip: Minimally create the important folders such as:
- Music
- Documents
- Movie (Videos)
- Downloads
- Pictures
All these folders are commonly used by the 3 OSes. I do NOT recommend changing of /home (OSX and / or Linux) and / or user home directory (Windows) either partially or as a whole.
This is because of compatibility issue.
On a side note, iTunes Media Library used in OSX and Windows are NOT able to be use interchangably due to hard-coded path used.
13. Useful troubleshooting in Fedora / Linux:
With references to these:
http://chaidarun.com/fedora-mbp
http://anderson.the-silvas.com/2014/02/14/fedora-20-on-a-macbook-pro-13-late-201 3-retina-display/
http://unencumberedbyfacts.com/2013/08/16/linux-on-a-macbook-pro-101/
I would like to highlight a few important points:
1) Wi-Fi driver:
http://rpmfusion.org/Configuration
Note 1: The sound driver should be installed at Out of Box Experience. However, the Wi-Fi is not.
Note 2: Install both free and non-free repository. By the way, some other software like VLC can only be found after the Free Repository is installed.
Search for "akmod-wl" in Gnome-Package-Installer in order to install Wi-Fi drivers
Note 3: For those who do not have Ethernet adapters and their Mac does NOT have a built-in Ethernet port, it is recommended to get one. This is because Fedora 20 does not have a good support for iPhone USB tethering. Unsure for Andriod / Blackberry / Windows Phone users.
2) Grub Menu:
It will show several options to boot into OSX, even of the capability to boot into x86 or x64 mode. However, neither of them is bootable except Linux and the rescue.
Hence, it is recommended to remove the items by hand in this file:
/boot/efi/EFI/fedora/grub.cfg
Command to be used:
"sudo gedit /boot/efi/EFI/fedora/grub.cfg"
Parts to be removed:
- For any extra kernels, delete the target entry by locating the line "menuentry" under "/etc/grub.d/10_linux" sector to one line above the next "menuentry".
It is recommended to keep one main kernel, and one recovery at the minimal.
- For other OS, delete all the entry (Since neither it can works) under "/etc/grub.d/30_os-prober" sector without removing the lines starts with ###.
Auto Mount exFAT partition:
- After installing extra packages for exFAT support (Since it is not supported by Fedora 20 from a default installation), you may wish to edit "/etc/fstab" in order to mount the exFAT partition during boot time.
Command to be used:
"sudo gedit /etc/fstab"
Add the following line in gedit:
UUID=702D-912D /run/media/Samuel/DATA exfat defaults 1 2
Note 1: For DATA partition, OSX & Boot Camp partition, Fedora defaults mounts under: "/run/medua/<Username with case sensitive>/<Partition Label Name>"
Note 2: UUID is unique ID. You can find out the UUID by:
Step 1: First determine the DATA partition number:
"sudo gdisk /dev/sda"
Step 2: Determine the UUID of this partition number:
"sudo blkid /dev/sda8"
Reference 1: http://manpages.courier-mta.org/htmlman5/fstab.5.html
Reference 2: http://liquidat.wordpress.com/2007/10/15/short-tip-get-uuid-of-hard-disks/
3) Overheating CPU
Solution is to issue the following command in Linux terminal: su -c "echo -n 1 > /sys/devices/system/cpu/intel_pstate/no_turbo"
4) System resumes immediately after suspend
Solution is to issue the following command in Linux terminal: su -c "echo XHC1 > /proc/acpi/wakeup"
5) What does not works well out of box:
- Both GNOME and KDE's fonts are too small to be readable for out of box experience. Additional configuration is a need. (Some of the info can be found on "More Tips" later)
- Thunderbolt hotplugging is NOT supported under Windows and Linux so far. Neither FaceTime HD camera works as well.
- The red light in Headphone jack is always on. I do not have luck in switching off the light without losing the sound.
Note 1: It is determined that the module "snd_hda_intel" is used by both cards (HDMI and normal output)
Note 2: It is also known that blacklisting it can switch off the redlight at the price of muting the system.
Note: Based on this article, http://support.apple.com/kb/TS1574
A Mac (Except Mac Pro) needs servicing when there is a red light while the system fails to detect internal speakers. However, this article does NOT applies to this issue.
5A) More Tips:
Install gnome-tweak-tool for more customization
Search for: "gnome-package" to install:
Install Gnome Package Installer for advanced package repository
Install Gnome Package Updater for advanced updates to be install (Whereby Fedora's App Store alike might not show the relevant updates)
14. Verify if disk is still GPT:
Use Gdisk to determine if the disk is pure GPT:
http://ubuntuforums.org/showthread.php?t=1742682
Command: sudo gdisk -l /dev/sda (The entire hard drive)
You should see the MBR is "Protective" instead of anything else.
15. Congrats, the system is ready for triple boot. (I forgot to eject my Windows DVD when the photo was taken)
Note 1: You cannot set the default startup disk in Linux due to the lack of Boot Camp Control Panel in Linux.
Neither is changing startup disk recommended in Windows due to the inability to display correctly.
For me, I click "Cancel" whenever I am on this tab (Feel free to make other Boot Camp adjustments in other tabs).
Only OSX I know that can show the startup disk options correctly.
Note 2: For some reason, OSX likes to auto mount the EFI partition everytime it boots up. It is not known to have any issue for ejecting other disks or mounting disks via Disk Utility.
Note 3: It is not determined if any Firmware or System upgrades will cause issues. It is only known that all 3 OS's regular updates should not be an issue.
System Updates excludes Mac OSX 10.9.3 updates to OSX 10.9.4 type as I had done it on a OSX 10.9.4 Mac or Windows 8.1 to Windows 8.1 Update 1 since my Windows DVD comes with Update 1.
System Upgrades refers to OSX Mavericks to Yosemite, Fedora 20 to Fedora 21, Windows 8.1 Update 1 to Windows 8.2 / Windows 9 for that matter.
Note 4: Reset SMC and / or PRAM will NOT affect your ability to boot any of the OS (OSX, Recovery HD, Fedora & Windows 8)
Yup, that is it!

Dual boot Windows 7 and Arch from 2 seperate drives (UEFI)

Hello everyone, I've been working on installing Arch to a secondary hard drive for the past few hours, but I am trying to make sure I won't mess up my Windows 7 install. I have found several topics talking about dual booting Windows 7 and Arch, but not a whole lot on booting them from separate drives. My drives are currently setup as follows.
sda (120GB SSD for Windows 7)
sda1 (100MB System Reserved NTFS partition)
sda2 (Windows 7 install)
sdb (1TB HDD for Windows programs, files, etc)
sdb1 (1TB NTFS partition)
sdc (1TB HDD)
sdc1 (boot 512MB FAT32)
sdc2 (root 500MB ext4)
sdc3 (home 300GB ext4)
sdc4 (swap 10GB)
rest unallocated "free space"
I used Gparted to create the partitions. I ended up getting hung up on the "Create Filesystems" sections, specifically this line"
# mkfs.fat -F32 /dev/sdXY
Now that I am looking at it, I'm thinking the "Create Filesystems" section maybe isn't necessary because I've used Gparted?
If it isn't necessary, when I get to the "mount the EFI System Partition to /boot" section, would I simply use
# mount /dev/sdc1 /mnt/boot
instead of
# mount /dev/sdXY /mnt/boot ?
The way I had this setup with Ubuntu was 3 partitions on sdc (/, home, swap) and I set my PC to boot to the sdc drive on startup. The boot loader would then give me the option to boot into Ubuntu or Windows 7, and I never had to alter the sda or sdb drives at all. Is this possible through Arch? My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct? That wouldn't be too big of a deal for me because I spend 90% of my time in Linux, and only use Windows for Photoshop and gaming occasionally.
Thanks for taking the time to read this. I would have just tested this out, but I am afraid of messing up my Windows install.

After several sleepless hours I had to give up and go to bed about 5 hours ago. The installation process went smoothly (or so I thought). I followed the tutorial closely and upon rebooting I was met with a blinking cursor. After some googling I found others who said I should press TAB, but nothing seemed to work.
I rebooted to the iso disk and found the "boot installed OS" option and noticed it said "Press TAB to edit". I then found the boot parameters and tried everything from hd0 0 to hd4 4. I believe I have Grub setup correctly because every option besides hd0 0 either says "Booting..." and then gets stuck, or says "That disk and partition combination does not exist". So yea, I think hd0 0 is the correct boot path, it just gets stuck with the blinking cursor.
silverhammermba wrote:
You have the right idea. You want to install a bootloader on sdc1 which will be able to boot both Arch and Windows.
Your best bet would be to use something like rEFInd. It has a "scanfor" option that should automatically detect your BIOS-configured Windows installation and add a boot option for it. Note that depending on your motherboard, you may have to switch to UEFI-only mode and Windows will be unbootable without the assistance of a UEFI program which is backwards compatible with BIOS (like rEFInd).
Thank you for the link. Considering I can't get into my install and the actual install only took about 30 minutes, I think I am going to just start from the beginning again with REFIndr. It seems much simpler. I only used Grub because I've used it before with Ubuntu, but my very limited knowledge is telling me Grub is probably the problem.
MoonSwan wrote:Just an idea: My bios has a "Boot-up Prompt" which I can invoke when it's POSTing by hitting F11. This brings me to a menu that allows me to choose which drive I want to boot up that day. I use it when Syslinux isn't working properly (Which is right now as a matter of fact ...) in order to boot Windows so I can do some SCII, for example. I, too, dual-boot but I have both OSes on different SSDs. So my 120GB Crucial SSD has Arch on it and the 240GB Kingston has Windows, SCII, Portable Apps, etc and nary the two shall meet. It makes dual-booting easier in the case of a corrupt OS or MBR or what-have-you. You may want to give your Bios a better look to see if you can do the F11 trick. It probably can and will usually tell you so at POST by printing that information on-screen along with your drives-detected and other messages (I hit Pause sometimes to read all the POST messages).
This is exactly what I was talking about doing when I mentioned:
My thinking is that even if it isn't, I should still be able to enter the BIOS boot menu and select which drive to boot manually correct?
That's good to know, because even if this next install doesn't work I think if I pull the other drives I should be able to get it working fairly easily.
Thanks again everyone.

Thinkpad x130e dual boot Win 7 and 8

So, I bought a new Seagate SSD Hybrid drive with the intention of dual booting Windows 7 and Windows 8. However, upon using my restore DVD's to reinstall Windows 7 on the new drive I hit a snag when trying to install Windows 8. The Win8 intall says that the drive needs to be GPT and it is currently MBR. So after removing the partitions and changing the drive to GPT I re-restore the Win7 OS. Then to my dismay I find that the drive has gone back to MBR during the restore proceedure.
Is there a way to edit the restore proceedure so that it doesn't change the drive over to an MBR drive?
Thanks,
Matt

the Arch partition should take some space from the windows7_os partition. You should keep the Lenovo_Recovery partition if you don't have a Windows installation DVD, or if you think you may want to reset your hard drive to its original state someday. In my laptop I have completely removed it.
I have a dual boot of Archlinux/Windows7, and I use the following partitioning
/dev/sda1 ntfs 60.0GiB /media/C (for windows os)
/dev/sda2 (extended partition)
/dev/sda3 swap 4.0GiB swap
/dev/sda4 ext4 30.0GiB root
/dev/sda5 ext4 30.0GiB home
/dev/sda6 ntfs 376GiB /media/D
I use the last partition as a shared partition between Arch and Windows, for storing music and videos... I use it also for installing games, so that I can play them either from windows or from Arch by using wine.
I'm not saying this is the best way to do it, but this has been working for me, also I don't use a separate /boot partition, I used to have it when I had multiple Linux distros, but with Arch alone I don't find it necessary.

Dual boot kali linux with windows 8

i have ideapad y510p and i want to dual boot kali linux with windows 8
i want a full guide to do it please !!help!!!

Hello,
if you got problems with the kernel, you can try backbox-linux. The kernel there is newer. It is based on Ubuntu 12.04 LTS.
Have a nice day
thoschi
LENOVO IDEAPAD Z710 59403383,i7-4700MQ,8 GB DDR3-RAM,1.920 x 1.080 Pixel,NVIDIA® GeForce® GT 740M,Hybrid (1 TB S-ATA + 8GB SSD)

Dual Boot Windows 7 and Arch with Shared NTFS partition.

Hi everyone,
I want to dual boot windows 7 and Arch Linux.
Here's the problem... my hard drive isn't the biggest. I want to store all my music, movies, pictures, and documents on partition that both linux and windows can access seamlessly.
I want the partition to be NTFS. -- (the programs that map an ext4 drive to Windows are trash).
Here's what I think I need.
30GB NTFS to Windows.
30GB ext4 to Arch Linux
The remainder (190ish GB) to Shared Data.
I don't want the swap partition because I have a SSD and 4GB of RAM.
What is the best way to setup my partitions? And is this even possible?
Thanks!

Not a problem. I would create:
First of four primary partitions for windows.
Second of four primary partitions for /boot
Third of four partitions is an extended partition encompassing all the space not used by the first two partitions.
Put everything else inside the extended partition.
Mine is a bit more complicated, but this should give you an idea:
ewaller@odin:~ 1005 %sudo fdisk -l /dev/sda
Password:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x87b33479
Device Boot Start End Blocks Id System
/dev/sda1 * 2048 121778159 60888056 7 HPFS/NTFS/exFAT
/dev/sda2 597366784 625135615 13884416 83 Linux
/dev/sda3 121778160 597366783 237794312 5 Extended
/dev/sda5 * 121778223 123770219 995998+ 83 Linux
/dev/sda6 123770283 131770589 4000153+ 82 Linux swap / Solaris
/dev/sda7 193213818 597360959 202073571 83 Linux
/dev/sda8 131781258 193213754 30716248+ 83 Linux
/dev/sda9 131770591 131781194 5302 1 FAT12
Partition table entries are not in disk order
ewaller@odin:~ 1006 %
Partitions 1 and 2 are Primary partitions. Partition 3 is an extended partition. All the others live in partition 3

Anyway to dual boot either Linux and Mac OS X?

Similar Messages

Maybe you are looking for