AP 1602 apply config from AP 1131AG

hello
At the moment i have ~30 AP's like 1131AG. Always for simplicity i was preparing new one like:
- saving config from existing one "Current Startup Configuration File"
- edit ( changing IP, Name, Radius IP )
- upload to new device.
Now i am not able to buy 1131AG (end of life) and i got offer for AP 1602.
My questions:
- can i upload configuration to AP 1602 as above using config from 1131AG ? ( even if i should adjust some config manually after upload )
( or i will have to config from scratch ?)
- just to confirm: On 1131 i am using Two RADIUS server, two SSIDs, vlans - is it still possible on 1602 ? or should i worry about loosing some capabilietes ?
P.S appologize in advance if those are "lamer" questions - i tried to find it prior post but with no luck.
Regards

Hi Tomas,
Hope you are talking about autonomous AP's here and if then you should be fine with this.
- can i upload configuration to AP 1602 as above using config from 1131AG ? ( even if i should adjust some config manually after upload )
ANS:- Most likely the 1602 AP you would be getting the will be having LWAP IOS (which works only with WLC). IF so you will have covert this autonomous mode and try configuring this as AP1131AG configuration with very little modifications. You could ask your reseller if they can get you a autonomous ios 1602 AP rather than lightweight then your life would be easier. Else you could use below url procedures to convert from LWAP to autonomous.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918https://supportforums.cisco.com/docs/DOC-14960
- just to confirm: On 1131 i am using Two RADIUS server, two SSIDs, vlans - is it still possible on 1602 ? or should i worry about loosing some capabilietes ?
You can acheive this on 1602 as well with out lose of any capabilities.
Hope that helps.
Regards
Najaf
Please rate when applicable or helpful !!!

Similar Messages

How to load a config from one appliance and publish it to both

Hi,
We're using AsyncOS7.5 on two WebAppliances S360 with a
Configuration Master 7.5 (M160).
I used one of both appliances to implement URL Filtering and now I'd like to transfer
this coniguration to the the master in order to publish it to both appliances.
As I could see it doesn't appear to be possible to load the config from one
specific appliance.
How can I do that the best?
Any hints?
Thanks
Jannis

Jannis,
You can import the config file from the WSA which URL filtering has been configured to the M160 in Configuration Master 7.5. This will wipe out the current configuration master 7.5 stored in the M160, and you can then publish the same config to the other WSA.
Check the online help for section "Initializing and Importing Configuration Masters"
Hope this helps.
- donny

How to transfert all my data and config from 4 to 4s

Hello,
Is there a "step by step" doc. On how to transfert all my data and config
From one iphone 4 to a 4s without using outlook ( ex:for contacts ) etc...
I don't get the ITunes method, sync direction etc...
All my Iphone 4 Put into my knew Iphone 4 S within a click !
Maybe there's an app for that :-).
Thanks for the Help.

iOS: Transferring information from your current iPhone, iPad, or iPod touch to a new device

What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

Hi Cisco Community / Friends,
I am new to this site though I have cisco account for many years. I am a CCNA ,I passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
We have a new project for the VSAT Comm'n of Coast Watch Station , The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for?
Appreciate your comments and help on this matter.. Thank You very much
Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
(Errors see below)
CWS_4_Pandami(config-erm)#mmi polling-interval 60
                         ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi auto-configure
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi pvc
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                        ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
CWS_4_Pandami(config-if)# bandwidth 256
CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
CWS_4_Pandami(config-if)# duplex auto
CWS_4_Pandami(config-if)# speed auto
CWS_4_Pandami(config-if)# priority-group 1
                                                    ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                          ^
% Invalid input detected at '^' marker.

Hi
From Cisco's website:
The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
So because this is your device, you don't want to use MMI anyways.
And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

Hi i am working with indesign on a book in hebrew. and the page numbering that i apply. showing from left to right insted of right to left. can you please help? thank you. iris

hi
i am working with indesign on a book in hebrew. and the page numbering that i apply. showing from left to right insted of right to left.
can you please help?
thank you. iris

Hi Shawninglewood,
Welcome to the Support Communities!
The article below may be able to help you with this.
How to delete content you've downloaded from the iTunes Store, App Store, iBooks Store, or Mac App Store
http://support.apple.com/kb/HT5772
Cheers,
- Judy

How to tranport XI config from DEV to QAS or PRD

Dear Sir,
We would like to know How to tranport XI config from DEV to QAS or PRD
Thank you and best regards,
Vimol

Hi,
Check some links on transporting Objects.
Transporting IR,ID Objects using File System
http://help.sap.com/saphelp_nw2004s/helpdata/en/93/a3a74046033913e10000000a155106/frameset.htm
http://help.sap.com/saphelp_nw2004s/helpdata/en/a8/5e56006c17e748a68bb3843ed5aab8/frameset.htm
How to handle SLD for Tranporting Dev to Quality ser
https://service.sap.com/~sapdownload/011000358700001684302005E/HowToSLDandXI.pdf
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/0fa2c490-0201-0010-61b4-df12869c4753
Transporting XI from DEV to QA
Transporting XI from DEV to QA
using CMS system. in XI
1. /people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
2. /people/sap.india5/blog/2005/11/09/xi-software-logistics-ii-overview
3. /people/sap.india5/blog/2005/11/28/xi-software-logistics-solution-iii-cms
4. /people/sravya.talanki2/blog/2005/11/02/overview-of-transition-from-dev-to-qa-in-xi --> Overview of Transition from Dev to QA in XI
5. /people/sravya.talanki2/blog/2005/12/20/inconsistencies-while-transporting-rfc-objects-from-dev-to-qa-150-sp12
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/9e76e511-0d01-0010-5c9d-9f768d644808
http://help.sap.com/saphelp_nw2004s/helpdata/en/93/a3a74046033913e10000000a155106/content.htm --> Transporting XI Objects
http://help.sap.com/saphelp_nw04/helpdata/en/ef/a21e3e0987760be10000000a114084/content .htm --> Configuring Groups and Transport Targets
Look into this blog for how to export / improt IR and ID objects,
/people/sap.india5/blog/2005/11/09/xi-software-logistics-ii-overview
/people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
Please go through these links which actualy show you how to configure CMS and also gives you all information regarding it.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/43f5d790-0201-0010-2984-ff72d822b109
http://help.sap.com/saphelp_nw04/helpdata/en/de/a4214174abef23e10000000a155106/content.htm
/people/daniel.wirbser/blog/2005/10/27/tcsfilecreateexception--error-while-assembly-of-software-components-in-nwdi
http://help.sap.com/saphelp_nw04/helpdata/en/f6/719a2172f74b67b150612a7cd3b7df/content.htm
http://www.sap-hefte.de/download/dateien/964/074_lesesprobe.pdf
Here are some blogs.
/people/sravya.talanki2/blog/2005/11/02/overview-of-transition-from-dev-to-qa-in-xi
/people/sap.india5/blog/2005/11/03/xi-software-logistics-1-sld-preparation
Re: Moving project from Dev to QA
Error while exporting/transporting the Business system from Dev to Quality
Transporting the scenario frm Dev Server to PRD Server
transporting data from Dev to quality using CMS
Regards,
Phani
Reward points if Helpful

Unable to refresh config from controller

After migrating the data from CPI 2.1 to 2.2, I am unable to refresh the config from controllers that are on version 7.0.220.0. I am able to refresh on the contrlollers that run on version 7.4 and 7.6 successfully. I checked the compatibiliy metrix and 7.0.220.0 is listed as a supported verison on CPI 2.2.
I open up a TAC but they have been struggling with this for the past 3 weeks now.
Please advice what could be the issue. Thank you.
Phil.

Hi. I had this same issue with 9.2. I found that there was a user which was no longer in the AD that was still in planning.
First thing to check is can you see the users in SS - I suspect not but worth a look. If you can, deprovision them. If you cant (most likely) you will need to use an LDAP browser to clean them out, which is a very messy process.
Best of luck.
Sean

Possible to set Dynamic Config from ABAP Proxy

Hi,
I know how to get and set Dynamic Config from Java/XSLT mappings and adapter modules. But I want to do this from an outbound ABAP Proxy Call (in the same way I can set the serialization context for EOIO), is that possible?
The scenario is: I have an interface; Proxy -> Xi -> ftp, with no mapping. It seems unnecessary to introduce a mapping just to set some dynamic config values for the receiving adapter which are already known at the outbound proxy call...
rgds Johan

Hi Bhavesh,
In the thread you mention it is shown that you can set Dynamic Config properties during an ABAP mapping. My question was if I can set these properties already in the proxy call? Or did I miss something?
Of-course I can introduce a dummy mapping in Java/XSLT/ABAP which copies the source message to the result message and sets the dynamic config properties, but I would rather not introduce a mapping if not neccessary...
rgds Johan

"Component Assignment Incomplete" while Apply Model from ESR

Hi all,
I am trying to configure a scenario by using Model Configurator with Tools->Apply Model from ESR.
My Process integration scenaro is : PAYE_EOY_GB which belongs to the swcv "E-FILING GB 1.0" whose content imported from ESR content available on sap marketplace.
I am trying to configure the scenaro.
The sender is a Business System "Sys_MyECC" which represents SAP ECC.
The reciever is UK govt gateway.. for which i created a party with the name "GovernmentGateway" and a Communication Component "GG_submission" within the party.
When i am in the model configurator, in the step 2 Assign Components, when i am selecting the sender Component as Sys_MyECC, it is giving the popup message:
Component Assignment Incomplete :
Each business component must be assigned a business system component. Incomplete assignments exist; these can be removed automatically.
What does this message is trying to convey.
thanks in advance,
Madhu_1980.

Besides having a Business System, you need a Business system Service to have a B2B communication
I did not get what exaclty the Business system Service means.
for the sender, we have SAP ECC, the scenario will be triggered using sproxy communication.
so, we created a Business System representing the ECC server.
the "Bysiness system service" means.. does it also represent ECC server, in pi 7.1, if we create Business Component, how we can link the Business Component with the Business system.

Apply Model from ESS Repository

Hi Sapall.
as iam new to SAP-PI7.1.1,i just want to know on how i can do the Apply Model From ESS Repository.
i have created the Process Integration Scenario in ESR with the all the data type,message type,message mapping,operation mapping but all i want to know here is how i can import Process Integration scenario from esr to Integration Directory.
will be waitign for your resposne.
regards.
varma

Hi,
To import Process Integration from ESR to ID. Keep Integration Directory in Folder View or Configuration Scenario View, Just right click and you will be able to see the option New Integration Process by clicking on that the wizard to import integration process from ESR to ID will open.
Regards,
Gautam Purohit

REMOVING IPSEC VPN CONFIG FROM PIX 6.3 FIREWALL

Hey,
we have pix 6.3 serving as internet firewall and we are int process of replacing it with new ASA Device. currently there are several site to site and remote vpn are configured for access purposes.
i tried to remove one site2site ipsec vpn from pix and it starts acting like a loop generating the same error with qty that processor got 100% CPU, couldn't logged in through normal ssh so i connected via console and place back the isakmp and crypto map commands back in and the error stops.
My purpose of this question is that how can i remove vpn config from pix without generating any error is there any formal process or order of removing rules from pix or we can do it one by one no order is required.
MY PROCESS OF REMOVING CONFIG:
REMOVE THE ACCESS-LIST INSIDEOUT AND OUTSIDE IN COMMANDS
REMOVE THE OBJECTS AND OBJECTS GROUPS
REMOVE THE VPN DEFINED ACCESS-LIST FOR INTERESTING TRAFFIC
REMOVE CRYPTO MAP TRANSFORM-SET
REMOVE ISAKMP-POLICY
REMOVE CRYPTO MAP
WE DO USE ISAKMP SHARED KAY MECHANISM "I DID NOT REMOVE THAT "
BUT AS SOON AS I REMOVE THE CRYPTO MAP FROM THE PIX I GOT THIS ERROR
IPSEC(crypto_map_check): crypto map XYZ 20 incomplete. No peer or access-list specified.
20 IS THE ISAKMP POLICY NUMBER & Peer and Access-list was removed from pix
any help would great
regards

Hi
You could do either of 2 things.
1) Enable NAT-Traversal on your ASA
2) Add the following on your pix :
fixup protocol esp-ike
This allows one IPSEC connection to run through PAT.
HTH
Jon

How to push the config from WCS to WLC

Hi Everyone
sorry a total noob here. I had to reset factory my WLC. how can I download the config from WCS? Cisco Prime? I have the config backed up there but I cant see an option to push the config
thanks alot

If the device is already in the Prime Infrastructure, you can open it in Device work center and select the device > use the configuration archive option > scheduled deploy.
Also, the Prime Infrastructure Plug and Play feature allows you to perform an initial provisioning of a software image and configuration on a new device. For more details check :
Automating Device Deployment Using Plug and Play Profiles
Working with Device Configurations
-Thanks
Vinod

How to import config from 4404 WLC to WLC 5508

Hi all
In one week I need to import the config from my 4404 WLC to my new 5508, then I just want to change the mgnt IP address of the 5508 and then bring it into the same mobility group.
How do I import the config when the 5508 is straight out of the box?
Many thanks
Carl

Heck!!!!
This is unfortunately correct as per the doc you provided! :-(
I am already aware that there are some commands and features differs among different platforms but I thought Cisco passed this barrier by making WLC platform chooses appropriate commands from config file and ignore commands that does not suite importing platform!! but it does not seem to be correct!!!!!
I think if backup config file has only features that another platform support then config restore would possibly work.
But if config file has commands that considered unknown to the importing platform then here the problem may reside!
Surendra: do you know what are the consequences of doing this unsupported scenario of moving backup config amont different platforms?
I think Carl can try restoration process anyway and if does not work he can go to manual configuraiton then. But he is still have the chance of getting the config restored correctly.

WCS Refresh Config from Controller Fails

Have been able to refresh config from controller successfully in the past, but now it only works on 1 of 4 controllers. Receive error "Failed (see logs)". Any idea why this would fail, and/or where I can find these logs? All controllers are reachable.

For what it's worth, it is generally recommended that the WCS be at a MORE recent or same revision level (in terms of date, not version numbering, per se) as the controllers.
Have you upgraded the controllers prior to the WCS? It is my understanding that upgrading in the wrong order (i.e.: Upgrading the WLC/WiSM before the WCS is upgraded) might cause problems.
Just a thought.
- John

I have configured bowser url in about:config from there onwords i am unable to find orange box on left corner and menu on the right corner as well as navigation

i have configured browser URL at about:config from there onwords i am not able to find orange box,menu,navigation every thing and before opening firefox it is asking permission every time

What kind of permission do you mean?
Do you mean about making changes?
A possible cause of this error is that Firefox is set to run as Administrator.
Check that Firefox isn't set to run as Administrator.
Right-click the Firefox desktop shortcut and choose "Properties".
Make sure that all items are deselected in the "Compatibility" tab of the Properties window.
* Privilege Level: "Run this program as Administrator" should not be selected
* "Run this program in compatibility mode for:" should not be selected
Make sure that you do not run Firefox in full screen mode (press F11 or Fn + F11 to toggle; Mac: Command+Shift+F).
*https://support.mozilla.org/kb/how-to-use-full-screen
You can use one of these to set which toolbars to show.
*"3-bar" Firefox menu button > Customize > Show/Hide Toolbars
*View > Toolbars (press F10 to show the Menu bar)
*Right-click empty toolbar area

AP 1602 apply config from AP 1131AG

Similar Messages

Maybe you are looking for