App-v 5 Dependacy : VC++ 2012 Mini Runtime 'Update Error'

HI Everybody,
we have been deploying App-v 5 SP1 via SCCM App Deployment for about 7 months now and all was good. however all of a sudden we are getting wide spread reports of software centre complaining that and
'Update Failed' for App-v.
Looking into the logs it looks like this is the reason.
Product: Microsoft Visual C++ 2012 x64 Minimum Runtime - 11.0.60610 -- A later version of Microsoft Visual C++ 2012 x64 Minimum Runtime - 11.0.60610 is already
installed.
So I think something has went wrong with the detection method, as we were only looking at MSI code to detection so I added an OR to look for the VC++
2012 reg keys. however that still dose not work. so I changed an exit code as 1603 as a success but still not working, has anybody started to see this ? anybody know of a good way to resolve this ?
any help will be most welcome.
\\SC
P.s attached some screen shots of logs and general setup for VC++ 2012

The detection method you're using isn't working, it can be seen from the screenshot you posted:
*** Application not discovered...
Use SOFTWARE\Microsoft\VisualStudio\11.0\VC\Runtime\x64 as the registry key and place a mark on the checkbox "This registry key is associated with a 32-bit application on 64-bit systems".
Also, the MSI product code should be enough. Are you sure you're using the correct product code? You can add the correct one by extracting the MSI package out of vcredist.exe. More info on this can be found here:
http://www.applepie.se/extract-msi-from-visual-c-2012-redistributable

Similar Messages

  • DPM 2012 UR3 Agent Update Error: HRESULT E_FAIL...DCOM Error

    My DPM Server is Windows 2008 R2 SP1 with a locally installed SQL and DPM Server and fully patched. My Workstations are all Windows 7 Ultimate x64, fully patched. I have manually installed the DPM RTM Agent and pushed the UR2 update from the DPM Server
    without any challenges or issues. I have SCEP running with process exclusions for the DPM services on the WS and DPM Server. I’ve been running DPM 2012 RTM and then UR2 without any issues or challenges to-date.
    I have recently updated my DPM 2012 Server from UR2 to UR3 and pushed out all the Agent Updates, which appeared to go successfully from the DPM Console perspective. I spot checked a few systems, 1 workstation (WS) and 1 server, everything looked good. A
    couple of days after this I noticed 2 of my workstations failed backing up to Tape. I noticed the recovery options available for these WS’s have stopped updating hours after pushing the UR3 Agent update. The 2 WS’s I'm troubleshooting have a little different
    scenario. I have 2 other WS’s that were updated in the same manner and are working perfectly.
    Both WS cannot connect to the DPM Server and displays this DCOM Error:
    "ERROR:ERROR HRESULT E_FAIL has been returned from a call to a COM component."
    The 1st WS DPM Client has a Yelow Sign over-lay and "Administrator has not configured backups." when you hover over it.
    The 2nd WS does not the Yellow Sign over-lay.
    All the properties of the Local DPM Client Console 'Summary and Protected item'  tabs are not updated on the 1st WS but are on the 2nd WS.
    1st WS process:
    The Recovery Tab shows the available recover dates to choice from.
    I can expand one of the backup dates, folders and copy a file to this system.
    I can view my previous recovery Points from the console dating back to when I updated the Agents.
    I’ve validated the DCOM settings on both WS's compared to a WS that is working, they are the same.
    I uninstalled the agent manually, then copied and reinstalled the new UR3 Agent Version with the same outcome.
    I uninstalled the new version and reinstalled the previous version, same error.
    I then proceeded with upgrading UR2 agent version installing the UR3 version over the top, same error.
    I logged on to this WS as the Domain Admin, removed and reinstalled the UR3 version, same error.
    I removed, applied and then re-added the DPM server to the local WS DPM and DCOM Groups.
    I removed, applied and then re-added the WS from the Groups on the DPM Server.
    I’m able to see, ping and view other backup folders presented on the DPM server on this WS.
    In the DPM Console I am able to connect to this Workstation successfully from the Administrative, Agent Space.
    The DPMClientProtectionCurr.errlog file shows this repeatedly:
    0FC0   
    065C    10/13   05:02:32.499 
    03        service.cpp(298)         
    [000000000021FD90]            
    ACTIVITY         
    CService::AnnounceServiceStatus
    0FC0   
    0D18    10/13   05:02:33.059 
    33        dlsclientprotection.cpp(778)           
    [00000000002BC850]            
    NORMAL          
    Connecting to DPM Server: (<Server.FQDN>)
    0FC0   
    0D18    10/13   05:02:33.171 
    33        dlsclientprotection.cpp(861)           
    [00000000002BC850]            
    WARNING         Failed: Hr: = [0x80004005] : Failed to set client OS details - ClientName:<WS.FQDN>, ClientOSVersion:6.1.7601, OSType:2, AgentVersion: 4.0.1920.0
    0FC0   
    0D18    10/13   05:02:33.171 
    33        dlsclientprotection.cpp(1490)           
    [00000000002BC850]            
    WARNING         Failed: Hr: = [0x80004005] : Failed to get connection to DPM server: lVal : ConnectToDPMServer(bstrClientMachineName, &pIUnknown, &fConnectionSuccessful, &dCurrentStatus,
    exceptionResult)
    The
    DPMRACurr.eerlog show this for both WS's:
    0EF0 1110 10/13 04:05:02.157 22 genericthreadpool.cpp(824) [000000000093C360]  NORMAL Hr: = [0x80070002] CGenericThreadPool::m_dwMaximumNumberOfThreads[20]
    0EF0 1110 10/13 04:05:02.157 03 miscellaneousutils.cpp(918)   NORMAL Error:ERROR_UNKNOWN_PRODUCT, While detecting DPM version. Assuming DPM isnt installed.
    And this one repeatedly:
    0BE8 08EC 10/13 13:59:40.404 29 radefaultsubtask.cpp(382) [00000000002F1640] 4F801526-72F2-4460-8760-F9D6E127FECB WARNING Failed: Hr: = [0x809909b0] : CRADefaultSubTask: WorkitemID does not exist, {DB3F138D-DE37-414D-BADC-5A161C6E7E1C}
    0BE8 08EC 10/13 13:59:40.404 05 defaultsubtask.cpp(546) [00000000002F1640] 4F801526-72F2-4460-8760-F9D6E127FECB WARNING Failed: Hr: = [0x809909b0] : Encountered Failure: : lVal : CommandReceivedSpecific(pCommand,
    pOvl)
    0BE8 08EC 10/13 13:59:40.404 05 defaultsubtask.cpp(751) [00000000002F1640] 4F801526-72F2-4460-8760-F9D6E127FECB WARNING Failed: Hr: = [0x809909b0] : Encountered Failure: : lVal : CommandReceived(pAgentOvl)
    The 2nd WS Process:
    I did not remove or touch the local agent installation because the information is populated on this client’s agent properties fields.
    I can see the folder selections I’ve chosen to be backed up by the protection group configuration.
    When i open the Agent UI I receive the sam DCOM error.
    I also receive a different error message on this WS when I try and do a Sync Now from the General Tab: Failed to trigger synchronization.
    I was able to perform a consistency check on this WS that completed successfully from the DPM server.
    I’ve validated the networking configuration settings are correct.
    I flushed local DNS cache.
    Thanks,
    Paul

    Hi,
    I have a Windows 7 x64 machine that exhibits this problem. It seems that it is not caused on the client side but on the server side.
    In our case the server logs the following every time the client tries to connect:
    WARNING    Verify disconnected client failed with exception: System.ArgumentException: Das Element wurde bereits hinzugefügt. Schlüssel im Wörterbuch: "<machinename>". Hinzuzufügender Schlüssel: "<machinename>".
    (Translation: Element has already been added. Key in Table: "<machinename>". Key to be added: "<machinename>".
    I have uninstalled the agent on the client several times. One time I have seen the following error message on the server side:
    Deployment.cs(2815)            NORMAL    Removing all agent records for server[<machinename>] from table InstalledAgent.
    ntlmutils.cpp(185)            WARNING    Failed: Hr: = [0x80070002] : Error trying to open key [HKLM\Software\Microsoft\Microsoft Data Protection Manager\Agent\2.0\NtlmAuthData\<machinename>]
    SchedulerImpl.cs(166)            NORMAL    Entering DeRegister, JobDefID: bafe2b8b-53b2-4694-aa28-9e2c6c152d51
    Catalog.cs(1006)            WARNING    No retry on exception The specified @name ('') does not exist. while executing sp_delete_alert
    Catalog.cs(1013)            WARNING    SqlException encountered, SqlRetryCommand diag details - SqlCommandText  => Name=msdb.dbo.sp_delete_alert, CommandType=StoredProcedure
    Catalog.cs(1013)            WARNING    CommandDiagInfo => CanRetry=False, CommandTimeout=3600
    Catalog.cs(1013)            WARNING    CommandParams   => Count=2, InTx=True
    Catalog.cs(1013)            WARNING         Param[0]   => ParameterName=@name | Value= | Size=0 | DbType=NVarChar | Direction=Input | IsNullable=False
    Catalog.cs(1013)            WARNING         Param[1]   => ParameterName=@RETURN_VALUE | Value=1 | Size=0 | DbType=Int | Direction=ReturnValue | IsNullable=False
    EventManager.cs(98)            NORMAL    Publishing event from SchedulerImpl.cs(838): JobScheduleChange, [JobDefID=bafe2b8b-53b2-4694-aa28-9e2c6c152d51]
    Errors on the client side appear the moment the agent is re-added to the DPM server (I use "connect agent" instead of "install agent"). After that moment I get the message "Error connection to the DPM server. Error: a COM-component returned E_FAIL" every time
    I open the DPM client. This is mirrored by the Verify error mentioned above on the server side.
    To me it seems that parts of the machine config are still in the MSDB after removal (maybe caused by the registry error). If this client is connected again, the orphaned database entries cause the Verify error
    If that's true, how could we get rid of those entries? Would it help to rename the client?
    Uwe

  • I have a 2012 Mini with a fusion drive that won't boot from a usb cloned drive. It came with 10.8.2 pre installed. I have zapped the PRAM and reset the SMC. Any thoughts?

    I have a 2012 Mini with a fusion drive that won't boot from a usb cloned drive. It came with 10.8.2 pre installed. I have zapped the PRAM and reset the SMC. Any thoughts?

    When I tried using a recently downloaded (from the App store) version of MtLion 10.8.2 (12C60) I could NOT get the new MacMini to install or boot from a USB I had previously made. I was however able to use the Recovery Mode of the MacMini to create a bootable SSD which I had installed. The problem arose when I went back into Recovery DU as it saw the seperate drives (SSD & HD) as a broken Fusion Drive. Interestingly DU from the boot volume had NO issues and reported NO faults. It was the Recovery DU that identified the faulty Fusion Drive configuration. At this point I am definately out of my depth but my speculation is that the Recovery Volume is being used in some fashion to form the method or pattern that DU assigns files to the drives, System Report sees the drives as seperate volumes with all their individual characteristics.
    Disk Utility did not make a bootable USB, I don't have or use CCC or Super Duper.
    Here is the longer version I've been compiling:
    Having bought a late 2012 Mac Mini(6,2) i7 2.66GHZ with the standard 1TB 5400 HD and 4GB of RAM (base model) I immediately decided to install a Mercury Elite 6g 240GB SSD and up the RAM to 16GB. I received both shipments on the same day and had all my new toys in front of me. After following the video advice on OWC’s website for the installation of the second drive I started the mini and formatted the SSD to accept the OS from Recovery on the original HD. This MacMini shipped with 10.8.2 (12C2034) as the OS, the normal build of 10.8.2 is (12C60). Having used Recovery Disk Utility to format the SSD it came back with an error that DU could’t Repair. I went ahead and installed the OS on the SSD and the Mini booted normally from both drives. The issue I encountered with this setup was that iMovie encountered an “unexpected error” and would not save a completed project. I therefore decided to figure the drive issue out because I suspect the new Fusion File Management software didn’t like my configuration with drives that Recovery DU saw as needing to be “fixed”. After spending some time on the phone with both OWC and Apple Support I took the plunge and used Internet Recovery Disk Utility and allowed both drives to be “fixed” after which DU created a Fusion Drive (Logical Drive) that I then ran Repair Disk on and it showed up as a single drive in DU. It works perfectly as described by Apple’s site:
    http://support.apple.com/kb/HT5446
    Having checked the Link Speed and Negotiated Speed they both show as 6g so I’m pleased not to have lost performance due to it being fuzed to a 3g 5400 drive. The biggest drawback is that Apple’s Fusion Management only allows for 1 additional partition and I would have preferred more than that.
    I have sourced some additional information here:
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.macsales.com/15619-special-note-for-adding-an-ssd-to-a-2012-mac-mini ?
    http://blog.fosketts.net/2011/08/05/undocumented-corestorage-commands/
    If anyone has a factory Fusion Drive could you please post the Link and Negotiated Speeds of both drives? This information can be found in Apple > About This Mac > More Info… > System Report >  Serial ATA and the drives should show up as discrete drives with their info listed separately.

  • My  2012 Mini OS 10.7.5 cannot see the Ethernet connection to my Actiontec GT701 WG.  The Network Preferences says "cable unplugged".  The WiFi connection is working fine.  Please Thank You

    My  2012 Mini OS 10.7.5 cannot see the Ethernet connection to my Actiontec GT701 WG.  The Network Preferences says "cable unplugged".  The WiFi connection is working fine.  Please Thank You

    Never mind, problem solved.  When I retunred to the Network tab the message had changed to "connected, no IP address" so I got that from the WiFi tab and configured the Ethernet manually.  Have a nice day @:-)#

  • Flash app that allows users to create mini animations

    Hi,
    I am fairly new to flash, and was wondering if the community could point me in the right direction for my current project.
    I am looking to build an app that allows end users to draw and save mini animations (simple predetermined shapes that move in 2D).  So far I have a written a app that allows the user to draw a single frame using simple shapes and lines, but I am having some small troubles at this stage, and have not attempted to allow the user to animate or save the drawing.
    If anyone knows of a tutorial or some other resource to put me on the right path I would be very grateful.  I can also share what I have if anyone would be willing to give me some pointers (I am going to assume that as a newbie, my code could use a lot of improvement).
    Regards,
    Robbie Vos

    Hi Andei1,
    Thanks for the input.  I figured that the save functionality would be a little difficult. 
    However, if I can get the basic app going (allowing users to create mini animations) I think I should be able to get save going with some (ok, alot) of effort.
    Regards,
    Robbie Vos

  • I just bought a 2012 Mini Mac with i7 processor. When it arrives will I be able to hook it up to my AOC LCD TV (which I use as a monitor)? It's specs are 1280x1024 (XGA) resolution. Thanks.

    AOC LCD TV (XGA) as Monitor?  I just bought a 2012 Mini Mac with i7 processor. When it arrives will I be able to hook it up to my AOC LCD TV (which I use as a monitor)? It's specs are 1280x1024 (XGA) resolution. Thanks.

    Thanks, Loner T. I have a few of those laying around.

  • When I synced my iphone to our computer, it took on my husbands apple id account and now it asks for his password to update apps.  How do I get mine back?

    When I synced my iphone to our computer, it took on my husbands apple id account and now it asks for his password to update apps.  How do I get mine back?

    Yes, you can delete them from your phone by tapping the icon until it jiggles, then tap the black x.  You can verify that your Apple ID is still correct for future purchased by going to Settings>Store>Apple ID (at the bottom).  If it's wrong, tap the ID shown, sign out, sign back in using your ID.  Then you should be good to go.

  • I heard some promote use of "Terminal Services(RDS)", rather than App-V application with SCCM 2012 even if you have SCCM licens.

    Hi,
    I heard some promote use of "Terminal Services(RDS)", rather than App-V application with SCCM 2012 even if you have SCCM licens. The reason you dont need to repackage\test the application on an client OS...
    I don't agree and I have not Heard this Before, just that you use TS for some scenario.
    Or is it more likely that "Terminal Services(RDS)", take over the applikation administration?
    /SaiTech

    Surely this all depends on your environment. There's nothing wrong with creating RemoteApps to push to client devices. Maybe you have an environment where RDS is widely used. 
    Why not leverage both solutions and target App-V's at RDS servers and then create App-V based RemoteApps that users can run at home as part of a home working solution via RDWeb.
    Creating apps via RDS will be an admin overhead yes but then so is creating App-V packages in SCCM.
    I don't agree with the arguement re: 'you dont need to repackage\test the application on an client OS...' as
    App-V allows you to run on multple O/S types. 
    To be honest both technologies have their pros and cons. 
    Cheers
    Paul | sccmentor.wordpress.com

  • Adding an app-v package to SCVMM 2012 R2

    Hi,
    I sequenced an application with App-v Sequencer 5.0 SP1. I don't have an app-v infrastructure (Server, Streaming ...). When the application is sequenced, I have the following files:
    Report.xml
    Application_Name.appv
    Application_Name.msi
    Application_Name_DeploymentConfig.xml
    Application_Name_UserConfig.xml
    I created a folder in my VMM Library with all these files. When a refresh of the library is done, I only have these files:
    Report.xml
    Application_Name_DeploymentConfig.xml
    Application_Name_UserConfig.xml
    If I well understand, only .OSD files are supported for App-v packages in VMM library. So I would like to know how to add my app-v package and deploy it from VMM with an application profile please.
    Thank you for help.

    Hi Hasan,
    I haven't seen this issue before, but the following post provides information on checking the registry value:
    https://wmoore.wordpress.com/2014/04/11/appcontroller-2012-r2-vmm-registration-error/
    The usual caveats about editing the registry apply, including make a backup first.
    Regards
    Richard
    This posting is provided "AS IS" with no warranties, and confers no rights.

  • App-V Streaming in SCCM 2012 - High Availability Possible?

    Hello All,
    Background:
    I'm in the process of designing an SCCM 2012 R2 environment, and one of the things that needs planning for is App-V.
    Currently the client uses App-V 4.5 management servers with a mixture of 4.5 and 4.6 apps so I've been told. There are 2 servers and they are load balanced, I think the SQL server used is clustered. I need to bring this App-V environment into SCCM 2012 R2,
    and as such I am concerned about High availability. (I'm also aware of compatibility of app v packages but this is beside the point)
    SCCM will manage around 7000 workstations, and up to 20,000 users all in all (obviously not at once). The majority of users use any machine, they do not have dedicated ones. The hierarchy will consist of one standalone primary site with SQL on box and I will
    be configuring multiple distribution points and management points.
    Question:
    It is my understanding that Management Points cache policies, and distribution points obviously have all the data cached so to speak. Therefore, if a user is already assigned to a group which is assigned to particular streamed applications - if connection was
    lost to the site database server, and they logged onto a new machine, would they still be able to run those streamed applications? Or would the Site database going down break this?
    Thanks
    Stefan

    Yeah that's a good point Torsten, Thanks - this is what I was unclear on and wanted clarification on. Was happy with the answer but thinking about it now you have said that, I dont see how that can work either...
    If im getting it right now, it would be ok if someone has already logged onto the machine, as the profile would have already been populated with the virtual application information pulled down after the client had run the evaluation and MP had retreived
    the information from the site DB when it was previously online - in that case the application would still work (and be visible) as the client has previoulsy known about it and clicking it can still stream it from the DB.
    But in the case of a new login, are we saying that the MP does not cache policies to the extent that it would know that user would be assigned a particular application - it would have to go back to the site DB for this information - which would be unavaliable
    and therefore would break it?

  • I can't open all apps I download on my iPad mini!!

    I Can't open all apps I download on my iPad mini pls help What should I do..

    Do you have enough free space on your iPad for it to run efficiently? With iOS 8 it is recommended that you have 15-20% of the storage space on the device free.  For a 16 GB device that is 2.4-3.2 GB free. For a 32 GB device that is 4.8-6.4 GB free. For a 64 GB device that is 9.6-12.8 GB free.
    Try quitting all apps and then reset the iPad. Double click the Home button to show the screen with running and recently used apps. Each app icon will have a sample page above it. Flick up on the page (not the app icon) and the page will fly away and the app icon will disappear. This quits that app. Do this for all apps that appear there. Then reset the iPad. Press and hold both the Home button and the Sleep/Wake button continuously until the Apple logo appears. Then release the button and let the device restart. You will not lose data doing this. It's like a computer reboot.

  • Can I install osx leopard 10.5.6 on a 2012 mini to run cs2?

    can I install osx leopard 10.5.6 on a 2012 mini to run cs2?

    is there any way that I can run Adobe Creative Suite 2 on a 2012 mac mini?

  • 0x80004005: app install failed - OSD SCCM 2012 R2 - randomly

                    
    Hi,
    I have visited many forums with this error before posting.
    Problem : During TS New computer OSD, app failed to install randomly on all model Win 7 x86 or x64.
    Information :
    App concerned : Adobe flash, office, chrome...
    Domain integration : OK
    App installation tested across software center : OK
    smsts.log error  :
    Policy Evaluation failed, hr=0x80004005
    Install application action failed: 'Adobe Shockwave Player '. Error Code 0x80004005 InstallApplication
    LocationServices.log error :
    Policy prevents failover to WINS for lookup
    Successfully sent location services HTTP failure message.
    Error sending HEAD request. HTTP code 401, status 'Unauthorized'
    Client is not assigned to a site. Cannot get security settings.
    Client is not assigned to a site. Cannot get site signing cert.
    An idea ?

    Hi, 
    I create another topic and my problem (App install during OSD) is now solved yes:
    http://social.technet.microsoft.com/Forums/en-US/bb10bfc3-f5ec-46a6-9535-ea299266795c/strange-problem-app-install-failed-randomly-osd-sccm-2012-r2?forum=configmanagerosd#f54d0af1-2658-49ee-a57a-1ec9e2b09a3e
    You can Check "Continue on error" inside  "Options" Tab on your TS. Even if App install fail At least the rest ends well...

  • My iPad mini won't update my apps.  I have closed all open apps, done multiple resets but I show 24 updates and when I hit the update, the screen is blank.

    My iPad mini won't update my apps.  I have closed all open apps and done multiple resets.  I hit update and the screen is blank, even though the bubble shows 14 to update.

    If you are getting the blank app update screen, many people are having this problem over the last couple of days.
    According to Fly150 in another discussion, this will work.
    If you want to update the Apps while waiting for Apple to fix Updates:
    1. Go to App Store
    2. Select Purchased
    3. Select All
    4. Scroll down to find the Apps showing update
    5. Select update on the Apps
    This should update the Apps and get rid of the update count in App Store. Apple needs to fix this. It is a workaround only until then.

  • Can't transfer app from iTunes to ipad Mini without updates transferring as well

    I like to download the occasional app to iTunes then transfer it later to my iPad Mini.
    However I find that later when I try just to transfer that app to my ipad,  iTunes insists on transferring updates of other apps as well ?
    Is there a way to stop this ?

    I don't want to download again as I have a download limit and some of these apps are very large and take a big chunk out of that limit.
    This is why I download to iTunes on my pc so I can then transfer to other devices without affecting my limit.
    It also makes a convenient local backup.

Maybe you are looking for