Apple MAC Bonjour and Cisco Aironet 1142
Hi All,
Hope all is well.
We have a strange issue with our two Aironet 1142s and how it interacts with our Apple laptops. When we try printing to a printer in one room connected to (let's call it Aironet 2) we can't. We attempt to browse using Bonjour (Apple's protocol) to the printer and can't. HOWEVER.. we can print and browse fine when we're using Aironet 1.
Another strange thing is when we're on Aironet 2 we can ping to the printers just fine, just can't browse to is using Bonjour nor print of course.
Please help! Any inputs appreciated.
-Tom
Natalia,
You need to do the following to make Bonjour printing to work.
Have multicast enabled on the wired side for all the vlans involved (management, ap manager, client, APs). if any of these vlans are not properly setup, then bonjour will not work.
Wired Side:
Router:
ip multicast-routing (enable multicast globally)
For each vlan interface enable ip pim sparse-dense-mode:
conf t
interface vlan x
ip pim spare-dense-mode (there may be a syntax error, dont have router access at the moment)
also you may need to configure a rendevouz point which you can set to layer 3 interface of the management vlan.
For example (management ip 10.1.1.10 and g/w is 10.1.1.1)
ip pim rp-address 10.1.1.1 (again syntax maybe incorrect)
Note: you will have to configure the same on all routers in between the WLC and the APs
Also make sure that the ipads/iphones and wireless printers are connected to the same ssid (same vlan). Bonjour uses link local address which are not routable.
on the WLC, set up multicast multicast mode with a unique mutlicast ip address. Also, on the multicast tab, Controller > multicast > enable global multicast.
There is a catch here. You will mostly likely have to turn off IGMP snooping on the controller (controller > multicast > disable igmp snooping). I have learnt it the hard way that some of the apple devices dont send the igmp join reports.
Similar Messages
-
I have a Apple Mac desktop and recently can no longer access Youtube, videos, movies, etc because I get a message reading "Blocked Plug-in". There's no error message but it does say to upload Abode Flash Player and the problem will be solved. I do this but it doesn't fix the problem. What am I doing wrong?
if you already downloaded the adobe flash player onto your mac and still getting that message that means you need to finish the installation of the flash player
you do this by opening a finder window and going to your downloads, find the flash player in here and then double click on it and follow the prompts to complete the installation.
after this is completed you will need to completely quit out of the web browser you're using then reopen it for the change to take affect and your issue should be resolved. if it's not you need to contact adobe their number is 800 642-3623. -
Adobe Acrobat 9 Pro on both my Apple Mac Pro and Apple MacBook Pro
I think I found the answer to my question: "May I install my copy of Adobe Acrobat 9 Pro on both my Apple Mac Pro and on my recently purchased Apple MacBook Pro?" I think my question was answered in reading the text of the agreement for use of this site in the following:
"You may activate the Software on up to 2 devices (or virtual machines) at a time, if these activations are associated with the same Adobe ID for the same individual, unless stated at http://www.adobe.com/go/activation . However, you may not use the Software on these devices simultaneously."
If this is correct, would you confirm. I know how security conscious Adobe is with their software.
Thank you! Be Safe!
KenHi kennethf71183385,
Thank you so much for asking! Yes, you are entitled to activate your copy of Acrobat on two computers. Please see Activation & Deactivation Help - Adobe Support for more information about activating Adobe software!
Please let us know if you have additional questions.
Best,
Sara -
Hi there, I have just purchased an apple mac air and i want to delete some photos i have put on i photo.I am used to windows where you right click and press delete.Does anybody know how to do it? Cheers Pete.
lamptramp wrote:
Hi there, I have just purchased an apple mac air and i want to delete some photos i have put on i photo
Open iPhoto and from the Menu Bar... Click on Help... Type in Delete and choose from the Selected Topics.
lamptramp wrote:
... am used to windows ...
See > http://www.apple.com/support/macbasics/ -
Mac Lion and Cisco VPN client problems
I just installed Lion 10.7 on my iMac and can no longer use the downloaded Cisco VPN client to connect to Microsoft Remote Desktop and access the PC in my company's office. When I try to launch the VPN client I get Error 51. I used to be able to enter a command in the Terminal as a workaround to use the VPN client when that happened, but that no longer works. I have tried booting into 32-bit mode; doesn't work. I tried to use the Cisco client built into Lion using settings provided by my company. When I try to connect I get the following message: "The negotiation with the VPN server failed. Verify the server address and try reconnecting."
I have searched the web looking for a solution. My company's tech department is stumped; the Apple Geniuses haven't been able to help. Does anyone have any ideas how I can use either the downloaded Cisco VPN client or the client built into Lion?
Sent from Cisco Technical Support iPad AppHere is the link which you can use to configure the inbuilt VPN client in MAC Lion.
http://glazenbakje.wordpress.com/2011/07/28/how-to-create-a-cisco-vpn-connection-in-apple-mac-os-x-lion/
Make sure you configure the attributes correctly.
Secondly the inbuilt VPN client code of Lion is made in collaboration with Cisco so there will not be any issues of compatibility.
Cheers,
Rohan -
Mac software for Cisco Aironet 340
I have a Cisco Aironet 340 PCMCIA card that I want to use with an old PowerBook. But I can't find the download for the Mac software for this card. This page tells me to go to "http://www.cisco.com/pcgi-bin/tablebuild.pl/aironet-utils-mac." but it just redirects me to the normal software download page. Where can I download the Mac sofrware for this card?
It was never supported on a mac and this is end of life and end of support... your not going to find one especially on Cisco's site. Maybe search online and someone might have it on a file share.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Airport and Cisco Aironet over Radius
Does anybody know how to configure a MacBookPro with built in Airportcard to connect to Cisco Aironet 1231 WLAN Router with LEAP Authentication over Radius Server?? I can connect to it when no security is activated but if LEAP is on no connection and no request is on the Server from the Client??!! Thanks in advance.
Does anybody know how to configure a MacBookPro with
built in Airportcard to connect to Cisco Aironet 1231
WLAN Router with LEAP Authentication over Radius
Server?? I can connect to it when no security is
activated but if LEAP is on no connection and no
request is on the Server from the Client??!! Thanks
in advance.
I am having the same problem with my MacBookPro. Currently, I have supplied data to Apple's engineers from my machine as this is a known problem with MacBookPro's. AluminumG4 notebooks have no trouble authenticating; therefore, this may be a problem with the Atheros chipset. I am hopeful that the next version update will fix the problem, but don't have any information from Apple to support that optimism.
Good luck,
Norm -
Cisco aironet 1142 -- LIGHTWEIGHT
Hello, Good morning
Can anyone help me with the case below?
We have a Cisco aironet 1162N connected to a Wireless Controller (LIGHTWEIGHT mode), the device failed and it needs to be replaced.
We have a Cisco aironet 1142N in stock available to use.
Can we proceed with the change just with disconnect the failed AP (model: 1162N ) and connect the new one (model: 1142N)?
Or there is any other task to be done before the change? since the WLC manages the configuration for each AP.
Thanks in advance,
Regards,
JefryIf the AP connected switch has Management vlan of WLC then new AP can be joined to WLC without manual intervention and can change the HA.
Unfortunately, telnet & ssh is disabled on out of box AP, even it is enabled it is not supported until it joins the WLC. However through console you can configure HA, manually join AP to specific WLC,..
Out of box AP configuration:-
Configuring AP info:-
Debug capwap console cli
Debug capwap client no-reload
capwap ap hostname
capwap ap ip address
capwap ap ip default-gateway
capwap ap controller ip address
Configuring HA on AP manually:-
capwap ap primary-base
capwap ap secondary-base
capwap ap tertiary-base
How to manually force an AP to join specific WLC:-
test capwap controller ip
test capwap controller name -
IPhone4 and Cisco Aironet 1141 access point - fail using WPAv2 Personal
I cannot get my iPhone4 (latest s/w) to connect to a Cisco Aironet 1141 access point if I specify WPAv2 Personal. It is a single access point without radius etc. I have no problems connecting using "no security", WEP or WPAv1. Is there a problem with the iPhone4 implementation of WPA2 as all my other PCs connect just fine on WPAv2?
With the Aironet 1141 I can switch security between WPAv1 & WPAv2 while keeping all other settings identical. Thus I can clearly demonstrate how the iPhone4 connects when both devices are set to WPAv1 yet will fail to connect when I switch both to WPAv2. As I have said, all other PCs I have connect via WPAv2 without any issues.I cannot get my iPhone4 (latest s/w) to connect to a Cisco Aironet 1141 access point if I specify WPAv2 Personal. It is a single access point without radius etc. I have no problems connecting using "no security", WEP or WPAv1. Is there a problem with the iPhone4 implementation of WPA2 as all my other PCs connect just fine on WPAv2?
With the Aironet 1141 I can switch security between WPAv1 & WPAv2 while keeping all other settings identical. Thus I can clearly demonstrate how the iPhone4 connects when both devices are set to WPAv1 yet will fail to connect when I switch both to WPAv2. As I have said, all other PCs I have connect via WPAv2 without any issues. -
My WRT310n won't work with my Appl Mac Mini and iPhone
Previously I had a weak signal using my WRT54G router. I usually got one or two bars in the house on my iPhone or Mac Mini. I recently "upgraded" to the WRT310N and now I cannot connect wirelessly at all on the mini and only one bar on the iPhone even with the phone inches away from the wireless router. I know these are both G devices, but I didn't expect performance to be worse than with my $49 54G router. Any suggestions?
Are your wireless settings still on auto? Try using the wide radio band with standard channels 1, 6 or 11.
The box said windows xp or better... So I installed Linux! -
WLC 5508 and Cisco Aironet 1242 LWAPP AIR-LAP1242AG-A-K9
i have deployed wlc 5508 ( image 7.0.98.0 ) with 1262N AP and all 45 AP's are working fine,
at the same site i had AP1242 which i have converted to LWAPP (8 of them), these accesspoint are registerd perfectly with 5508 but non of the radio's are up. i have selected different countries according to the part numbers but unfortunaly non of the radio's are coming up, pleaes help
SatheesAvailable:370.0(w) Used:32.4(w) Remaining:337.6(w)
Interface Admin Oper Power Device Class
(Watts)
Fa0/1 auto off 0.0 n/a n/a
Fa0/2 auto off 0.0 n/a n/a
Fa0/3 auto off 0.0 n/a n/a
Fa0/4 auto off 0.0 n/a n/a
Fa0/5 auto off 0.0 n/a n/a
Fa0/6 auto off 0.0 n/a n/a
Fa0/7 auto off 0.0 n/a n/a
Fa0/8 auto off 0.0 n/a n/a
Fa0/9 auto off 0.0 n/a n/a
Fa0/10 auto off 0.0 n/a n/a
Fa0/11 auto off 0.0 n/a n/a
Fa0/12 auto off 0.0 n/a n/a
Fa0/13 auto off 0.0 n/a n/a
Fa0/14 auto off 0.0 n/a n/a
Fa0/15 auto off 0.0 n/a n/a
Fa0/16 auto off 0.0 n/a n/a
Fa0/17 auto off 0.0 n/a n/a
Fa0/18 auto off 0.0 n/a n/a
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/19 auto off 0.0 n/a n/a
Fa0/20 auto off 0.0 n/a n/a
Fa0/21 auto off 0.0 n/a n/a
Fa0/22 auto off 0.0 n/a n/a
Fa0/23 auto off 0.0 n/a n/a
Fa0/24 auto off 0.0 n/a n/a
Fa0/25 auto off 0.0 n/a n/a
Fa0/26 auto off 0.0 n/a n/a
Fa0/27 auto off 0.0 n/a n/a
Fa0/28 auto off 0.0 n/a n/a
Fa0/29 auto off 0.0 n/a n/a
Fa0/30 auto off 0.0 n/a n/a
Fa0/31 auto off 0.0 n/a n/a
Fa0/32 auto off 0.0 n/a n/a
Fa0/33 auto off 0.0 n/a n/a
Fa0/34 auto off 0.0 n/a n/a
Fa0/35 auto off 0.0 n/a n/a
Fa0/36 auto off 0.0 n/a n/a
Fa0/37 auto off 0.0 n/a n/a
Fa0/38 auto off 0.0 n/a n/a
Fa0/39 auto off 0.0 n/a n/a
Fa0/40 auto off 0.0 n/a n/a
Fa0/41 auto on 15.0 cisco AIR-LAP1242AG Class 3
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/42 auto off 0.0 n/a n/a
Fa0/43 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/44 auto off 0.0 n/a n/a
Fa0/45 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/46 auto off 0.0 n/a n/a
Fa0/47 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/48 auto off 0.0 n/a n/a -
Apple airport express and cisco linksys e-3000
How does one get the linksys e 3000 router to recognize an airport express station?
The "n" version of the AirPort Express is capable of operating on either the 2.4 or 5 GHz radio band ... but not simultaneously. That would mean it will attempt to connect to your E3000 on one or the other of its radios. This will typically be the 5 GHz radio if the AX is in the same room and the 2.4 GHz radio if it is farther away.
Note: The AirPorts do NOT support wide-channel (40 MHz) mode in the 2.4 GHz band. If your E3000 is configured for this; this may be the problem with it connecting. -
I have a problem with the headset of my ipod nano 4th gen. the right side don't have a sound. It comes in and out. what do I need to do.. I am using the original headset eversince. I tool it to a Apple Mac Cennter and Taked with a Service Center Rep. And he told me that they can't do anything because they don't repair the ipod they didn;t even look at it. I was told instead to buy a new one. I was very disappointed.. This is already my 5th ipod though i am planning to buy a new one.. I still want it fixed so I can give it to my little sister
From the OP: "My old computer got a virus and when that happened all my music was lost. "
They don't have the music on their computer so they cannot transfer the iTunes folder, from the computer to their iPod and then to the new computer. And if they try to enable disk use on the iPod it will erase all the music that is on it. The method you cited is moving the files in a data format using the iPod as a flash drive. It doesn't work if they are in music format. That is why I suggested Yamipod. -
Has anyone experienced electrical schock, tingling, burning and pain in the fingers, hand and wrist while using the apple mac desktop and the apple pro notebook?? If, so have you found a solution?? Never experienced this with any other computers and I have talked with my Doctor as well as a specialist and have had an EMG test for capatunel and nerve damage both test were negative
I have experienced some mild tingling if I touch the aluminum case on my iMac at the same time that I touch the metal cases on my external hard drives. They are all connected to the same surge suppressor and are on the same circuit, which is definitely properly grounded. I can't explain it, and I just make sure not to touch them at the same time.
I have never had any sensation touching just one of the devices alone. Is that what you are experiencing? -
I have a licence for Adobe Photoshop and Premiere Elements for my Windows 7 Desktop PC.
Have just bought Apple Mac Pro and it seems imovies wont import my AVCHD or AVI files - typical Apple narrow mindness.
Can I download a second copy or can I upgrade and get copy for my Apple Mac or do I have to buy from scratch.EnglishTrevor
What version of Premiere Elements is involved in your question? Be that as it may....
If your purchase of Premiere Elements was via the box packaging then you have an installation disc for the program on Windows and another installation disc for the program on Mac. No problem.
But, if you purchased the program as an download, you purchased only the version specific to the computer operating system to which it was downloaded.
Consequently, if you purchased Premiere Elements as download to your Windows computer, you will need to purchase Premiere Elements Mac for the Mac computer.
This is not Adobe. Rather a user to user forum. You can confirm the above with Adobe Sales. But what is described above is the way that is has been.
ATR
Maybe you are looking for
-
Function module call with destination
Hi, how can check if a function module call with destination works or not ? How can I debug. What can be the reason if it is not calles regards ertas
-
Multiline container table mod in ABAP WD
Hi, Looking for a quick guideline for macros/function modules to do the following:- 1] Read a multiline table into ABAP WD from workflow container 2] Append an entry to the table 3] Write the amended table into the workflow container. I have seen
-
WebSphere Portal and BOXI R2 PIK errors
Post Author: leonpc CA Forum: Publishing I have Business Objects installed on a system. I am trying to install the JSR168 portlets on a WebSphere Portal server to access this BOXI R2 server. I have followed the instructions and update the web.xml i
-
Deadline monitoring/Escalation - Purchase Requisition Workflow WS20000077
Dear Friends, I have read some stuff on SDN but still couldnt figure out the soultion. Its a common problem. We have set a release strategy in Purchase Requisition and are using std workflow WS20000077. Now the requirement is that if an approver does
-
Hello, it says it will take 65 hours to download a movie that was already purchased on the Cloud, How do I speed up the process. It says to go to Setting in I- tunes Store and select a lower video resolution but I don't see the Settings symbol in I