[Arch 64 bit] Powernow-k8 not loading at boot, loads fine afterwards

Question

I get the same error.
Has anyone solved it?
Last edited by deadshox (2010-09-22 20:02:36)

Answer 1

Thanks for seperating this topic.
Now 'powernow-k8' is starting fine. I don't no why, but it starts.
My 'rc.conf':
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="de_DE.UTF-8"
HARDWARECLOCK="UTC"
TIMEZONE="Europe/Berlin"
KEYMAP="de-latin1-nodeadkeys"
CONSOLEFONT="default8x16"
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(vboxdrv !atl1c !pcspkr !snd-mixer-oss !snd-pcm-oss !snd-hwdep !snd-page-alloc !snd-pcm !snd-timer !snd !snd-hda-codec !snd-hda-intel !soundcore atl1c pcspkr snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-codec snd-hda-intel soundcore lib80211_crypt_tkip wl acpi-cpufreq powernow-k8 cpufreq_ondemand cpufreq_powersave)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="keil"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(!eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Setting this to "yes" will skip network shutdown.
# This is required if your root device is on NFS.
NETWORK_PERSIST="no"
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng hal wicd @netfs @alsa laptop-mode)
// Edit
On my Notebook,
HP Compaq 615, 2.6.35-ARCH x86_64 AMD Athlon(tm)X2 DualCore QL-66 AuthenticAMD
i have the same problems with 'acpi-cpufreq' and there is all up to date, too.
Last edited by deadshox (2010-09-23 19:58:57)