ASA 5505-VPN- Can't use AD services

New install:5505 VPN with MS Active Directory services on LAN.
I can VPN into the network but cannot e.g. join my laptop to the Domain. Message says "cannot find "domain" I can: ping the PDC, RDP onto the PDC or any system on the LAN. Also applications that are on the remote laptop and rely on LAN resources fail.
Any help would be welcome

Sorry, just realized I did not attach config!

Similar Messages

  • ASA 5505 VPN can't access inside host

    I have setup remote VPN access on a ASA 5505 but cannot access the host or ASA when I login using the VPN. I can connect with the Cisco VPN client and the VPN light is on on the ASA and it shows that I'm connected. I have the correct Ip address but I cannot ping or connect to any of the internal addresses. I cannot find what I'm missing. I have the VPN bypassing the interface ACLs. Since I can login but not go anywhere I feel certian I missed something.
    part of config below
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.1.1.1 255.255.255.0
    ip local pool xxxx 10.1.1.50-10.1.1.55 mask 255.255.255.0
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto dynamic-map outside_dyn_map 40 set pfs
    crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
    crypto dynamic-map inside_dyn_map 20 set pfs
    crypto dynamic-map inside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic inside_dyn_map
    crypto map inside_map interface inside
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    service-policy global_policy global
    group-policy xxxxxxx internal
    group-policy xxxxxxx attributes
    banner value xxxxx Disaster Recovery Site
    wins-server none
    dns-server value 24.xxx.xxx.xx
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-session-timeout none
    vpn-filter none
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelall
    default-domain none
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout none
    ip-phone-bypass disable
    leap-bypass disable
    nem disable
    nac disable
    nac-sq-period 300
    nac-reval-period 36000
    nac-default-acl none
    address-pools value xxxxxx
    smartcard-removal-disconnect enable
    client-firewall none
    webvpn
    functions url-entry
    vpn-nac-exempt none
    no vpn-addr-assign aaa
    no vpn-addr-assign dhcp
    tunnel-group xxxx type ipsec-ra
    tunnel-group xxxx general-attributes
    address-pool xxxx
    default-group-policy xxxx
    tunnel-group blountdr ipsec-attributes
    pre-shared-key *

    I get the banner and IP adress info...
    This is what the client log provides...
    1 13:45:32.942 05/30/08 Sev=Warning/2 CVPND/0xE3400013
    AddRoute failed to add a route: code 87
    Destination 172.20.255.255
    Netmask 255.255.255.255
    Gateway 10.1.2.1
    Interface 10.1.2.5
    2 13:45:32.942 05/30/08 Sev=Warning/2 CM/0xA3100024
    Unable to add route. Network: ac14ffff, Netmask: ffffffff, Interface: a010205, Gateway: a010201.

  • ASA 5505 VPN can't access connected network

    I have an ASA 5505 with ipsec VPN configured on it.  I am able to  connect to the ASA but I can't ping a connected network.  I get a dhcp  assigned address in the network I am trying to reach but can't access  that network on Vlan5.  Please help.
    I attached the config.

    I think final questions, can you have two nat statements that point to the same acl ie.
    access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 192.168.0.0 255.255.255.0
    access-list no_nat extended permit ip 192.168.9.0 255.255.255.0 172.31.1.0 255.255.255.0
    access-list no_nat extended permit ip 192.168.5.0 255.255.255.0 192.168.5.0 255.255.255.0
    nat (inside) 0 access-list no_nat
    nat (inside) 1 192.168.9.0 255.255.255.0
    nat (fw-civic) 0 access-list no_nat
    nat (fw-civic) 1 192.168.5.0 255.255.255.0
    Or do I need to create a new acl for the fw-civic interface?
    Thanks

  • ASA 5505 VPN Can not connect clients

    Hi,
    I tried to search for an answer to this question but I couldn't find the answer.
    I configured the VPN on the ASA, I can not  get a client to connect to the ASA  I've tried and search for an answer and I really need som help!
    Any help is greatly appreciated.
    : Saved
    ASA Version 7.2(2)
    hostname
    domain-name
    enable password
    names
    ddns update method
    ddns both
    interface Vlan1
    nameif inside
    security-level 100
    ddns update hostname
    ddns update
    dhcp client update dns
    ip address 192.168.1.1 255.255.255.0
    ospf cost 10
    interface Vlan2
    nameif outside
    security-level 0
    ip address x.x.x.x 255.255.255.0
    ospf cost 10
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    switchport access vlan 3
    interface Ethernet0/6
    interface Ethernet0/7
    passwd 2KFQnbNIdI.2KYOU encrypted
    ftp mode passive
    dns domain-lookup inside
    dns domain-lookup outside
    dns server-group DefaultDNS
    name-server
    name-server
    domain-name
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    access-list EasyVPN_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
    access-list OUTSIDE_IN_ACL extended permit ip any any
    access-list OUTSIDE_IN_ACL extended permit icmp any interface outside
    access-list Remote-VPN_splitTunnelAcl standard permit any
    access-list DefaultRAGroup_splitTunnelAcl standard permit any
    access-list Bild_splitTunnelAcl standard permit any
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool TKK 192.168.1.200-192.168.1.220 mask 255.255.255.224
    ip local pool VPN-Pool 192.168.254.1-192.168.254.10 mask 255.255.255.0
    no failover
    monitor-interface inside
    monitor-interface outside
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any outside
    asdm image disk0:/asdm-522.bin
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    nat (outside) 0 access-list outside_nat0_outbound
    static (inside,inside) tcp interface 3389 access-list inside_nat_static
    static (inside,inside) tcp interface ftp access-list inside_nat_static_2
    static (outside,inside) x.x.x.x 192.168.1.0 netmask 255.255.255.255 dns
    access-group inside_access_in in interface inside
    access-group inside_access_out out interface inside
    access-group outside_access_in in interface outside
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    group-policy DefaultRAGroup internal
    group-policy DefaultRAGroup attributes
    vpn-tunnel-protocol l2tp-ipsec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl
    group-policy DfltGrpPolicy attributes
    banner none
    wins-server none
    dns-server value 192.168.1.253
    dhcp-network-scope none
    vpn-access-hours none
    vpn-simultaneous-logins 3
    vpn-idle-timeout 30
    vpn-session-timeout none
    vpn-filter none
    vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
    password-storage disable
    ip-comp disable
    re-xauth disable
    group-lock none
    pfs disable
    ipsec-udp disable
    ipsec-udp-port 10000
    split-tunnel-policy tunnelall
    split-tunnel-network-list none
    default-domain none
    split-dns none
    intercept-dhcp 255.255.255.255 disable
    secure-unit-authentication disable
    user-authentication disable
    user-authentication-idle-timeout 30
    ip-phone-bypass disable
    leap-bypass disable
    nem disable
    backup-servers keep-client-config
    msie-proxy server none
    msie-proxy method no-modify
    msie-proxy except-list none
    msie-proxy local-bypass disable
    nac disable
    nac-sq-period 300
    nac-reval-period 36000
    nac-default-acl none
    address-pools none
    client-firewall none
    client-access-rule none
    webvpn
      functions url-entry
      html-content-filter none
      homepage none
      keep-alive-ignore 4
      http-comp gzip
      filter none
      url-list none
      customization value DfltCustomization
      port-forward none
      port-forward-name value Application Access
      sso-server none
      deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission
    to use any of the VPN features. Contact your IT administrator for more information
      svc none
      svc keep-installer installed
      svc keepalive none
      svc rekey time none
      svc rekey method none
      svc dpd-interval client none
      svc dpd-interval gateway none
      svc compression deflate
    group-policy EasyVPN internal
    group-policy EasyVPN attributes
    dns-server value 192.168.1.253
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value EasyVPN_splitTunnelAcl
    default-domain value xxx.se
    group-policy Remote-VPN internal
    group-policy Remote-VPN attributes
    dns-server value 192.168.1.253
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Remote-VPN_splitTunnelAcl
    default-domain value xxx.se
    group-policy CiscoASA internal
    group-policy CiscoASA attributes
    dns-server value 192.168.1.253 x.x.x.x
    vpn-tunnel-protocol IPSec webvpn
    group-policy Bild internal
    group-policy Bild attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Bild_splitTunnelAcl
    username User attributes
    vpn-group-policy DfltGrpPolicy
    username Bild password encrypted privilege 0
    username Bild attributes
    vpn-group-policy Bild
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set TRANS_ESP_DES_SHA esp-des esp-sha-hmac
    crypto ipsec transform-set TRANS_ESP_DES_SHA mode transport
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 40 set pfs
    crypto dynamic-map outside_dyn_map 40 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 60 set pfs
    crypto dynamic-map outside_dyn_map 60 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 80 set pfs
    crypto dynamic-map outside_dyn_map 80 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 100 set pfs
    crypto dynamic-map outside_dyn_map 100 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 120 set pfs
    crypto dynamic-map outside_dyn_map 120 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 140 set pfs
    crypto dynamic-map outside_dyn_map 140 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 160 set pfs
    crypto dynamic-map outside_dyn_map 160 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 180 set pfs
    crypto dynamic-map outside_dyn_map 180 set transform-set TRANS_ESP_DES_SHA
    crypto dynamic-map outside_dyn_map 200 set pfs
    crypto dynamic-map outside_dyn_map 200 set transform-set ESP-DES-SHA
    crypto dynamic-map outside_dyn_map 220 set pfs
    crypto dynamic-map outside_dyn_map 220 set transform-set ESP-DES-SHA
    crypto dynamic-map inside_dyn_map 20 set pfs
    crypto dynamic-map inside_dyn_map 20 set transform-set ESP-DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic inside_dyn_map
    crypto map inside_map interface inside
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption des
    hash sha
    group 2
    lifetime 86400
    crypto isakmp nat-traversal  20
    crypto isakmp ipsec-over-tcp port 10000
    tunnel-group DefaultRAGroup general-attributes
    address-pool vpn
    default-group-policy DefaultRAGroup
    tunnel-group DefaultRAGroup ipsec-attributes
    pre-shared-key *
    tunnel-group Bild type ipsec-ra
    tunnel-group Bild general-attributes
    address-pool TKK
    default-group-policy Bild
    tunnel-group Bild ipsec-attributes
    pre-shared-key *
    tunnel-group CiscoASA type ipsec-ra
    tunnel-group CiscoASA general-attributes
    address-pool vpn
    default-group-policy CiscoASA
    tunnel-group CiscoASA ipsec-attributes
    pre-shared-key *
    tunnel-group EasyVPN type ipsec-ra
    tunnel-group EasyVPN general-attributes
    address-pool vpn
    default-group-policy EasyVPN
    tunnel-group EasyVPN ipsec-attributes
    pre-shared-key *
    tunnel-group Remote-VPN type ipsec-ra
    tunnel-group Remote-VPN general-attributes
    address-pool VPN-Pool
    default-group-policy Remote-VPN
    tunnel-group Remote-VPN ipsec-attributes
    pre-shared-key *
    class-map global-class
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global-policy
    class global-class
      inspect ftp
      inspect icmp
      inspect pptp
    service-policy global-policy global
    prompt hostname context
    Cryptochecksum:8cdda33b1993ba7bb33db88d996e939c
    : end

    Hi Fredrik,
    I see your acl "outside_nat0_outbound" set on inside interface for no nat, but I do not see, the acl is being defined anywhere on your config.
    I also strongly recommand create your vpn-pool to be different subnet rather being as same as your inside ip of your ASA.
    so, let assume your vpn pool is 192.168.255.1-254/24
    so, your no-nat for inside will look like this below.
    access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.255.0 255.255.255.0
    Let me know, if this helps.
    thanks

  • ASA 5505 VPN can't access inside hosts

    I have configured VPN on the 5505 using ASDM and I'm able to connect to the 5505 and the client is also getting an IP-address from the configured pool.
    The Cisco VPN client shows an error in the log: AddRoute failed to add a route: code 87
    Cisco

    No I can't ping anything.
    And here is the route -print after connection
    ===========================================================================
    Interface List
    0x1 ........................... MS TCP Loopback interface
    0x10003 ...00 0c 29 48 d4 50 ...... VMware Accelerated AMD PCNet Adapter - Packet Scheduler Miniport
    0x10004 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Packet Scheduler Miniport
    ===========================================================================
    ===========================================================================
    Active Routes:
    Network Destination Netmask Gateway Interface Metric
    0.0.0.0 0.0.0.0 192.168.222.101 192.168.222.100 1
    85.82.25.170 255.255.255.255 192.168.129.2 192.168.129.130 1
    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
    192.168.129.0 255.255.255.0 192.168.129.130 192.168.129.130 10
    192.168.129.0 255.255.255.0 192.168.222.101 192.168.222.100 10
    192.168.129.130 255.255.255.255 127.0.0.1 127.0.0.1 10
    192.168.129.254 255.255.255.255 192.168.129.130 192.168.129.130 1
    192.168.129.255 255.255.255.255 192.168.129.130 192.168.129.130 10
    192.168.222.100 255.255.255.255 127.0.0.1 127.0.0.1 10
    192.168.222.255 255.255.255.255 192.168.222.100 192.168.222.100 10
    224.0.0.0 240.0.0.0 192.168.129.130 192.168.129.130 10
    224.0.0.0 240.0.0.0 192.168.222.100 192.168.222.100 10
    255.255.255.255 255.255.255.255 192.168.129.130 192.168.129.130 1
    255.255.255.255 255.255.255.255 192.168.222.100 192.168.222.100 1
    Default Gateway: 192.168.222.101
    ===========================================================================
    Persistent Routes:
    None

  • Can i use the Service Module?

    Hello all,
    can i use the service module w/ the ff. scenario?
    items are manage by serial numbers., but we dont sell it, we purchase the item for internal use only. this are the ff. information that i want to track.
    1.     track the history of the item everytime it has undergone for repair
    a.     some cases the repair takes place within the company, meaning employees within the company take care on the labor but only parts will be purchase
    b.     some cases the repair takes place in business partner, (PO Service in this case)
    2.     track the parts that was replace
    what will be my work around for this. please advice
    best regards,
    Fidel

    Hi Fidel,
    You would need the following is you wanted to use the Service Module to track internal serialized inventory/hardware:
    1.  Set up a customer record that would represent the internal use/company/department
    2.  Manually create the Customer Equipment Card (when receiving the equipment on GRPO or AP invoice, you would want to use a warehouse that represents internally-used equipment/assets)
    Repairs:  you could update the status of the CEC record when it's being repaired (or have a repair WH for when it's sent off-site).
    Expenses:  related expenses could be done by creating a Service Call linked to the CEC with details/purpose, etc. which would be tracked on the Expenses tab but the transactions don't include AP (PO's), the assumption being that any expenses would be charged back to the customer, which in this case would be internal.
    If you want the expenses linked to the item/CEC then you could use Activities from Service Call and you can link the PO/AP invoice thru the Activity. You could have one S/C record that would be for tracking equipment repairs and leave it open for as long as you have the item - that would be the link between the Activities and the CEC/equipment record. Whenever repairs are to be record, you would only need to pull up the CEC record and drill-down to the S/C to create a new Activity record. This will also enable you to see how many repairs are being down - you could even breakdown the Activity on internal vs external (have it as a Type, on which you can then report on overall as well as by item).
    It will depend on what info you want to capture and if you need anything for reporting that would be that detailed (i.e. down to a serialized item) as to what process & setup you want to use. Try out the above and hopefully something will work out.
    HTH,
    Heather

  • How many vpn can be used simultaneously in Azure?

    I need to add multiple locations to my azure platform approximately 90 branches , I need to know if I should set up a vpn for each branch , or as I should. thank you very much .
    I am from Colombia , if they can write in Spanish would be better

    Hi,
    It seems that you have asked this question before:
    https://social.msdn.microsoft.com/Forums/azure/en-US/c533ff85-c155-4a19-8156-67901da66ee4/how-many-vpn-can-be-used-simultaneously-in-azure?forum=WAVirtualMachinesVirtualNetwork#c533ff85-c155-4a19-8156-67901da66ee4
    Based on my experience, the maximum limitation for virtual networks and local networks is 100 per subscription and the limitation for local network
    sites is 10 per virtual network in Azure. If you connect each on-premise branch with an Azure virtual network, it would be possible to do that. However, the default limitation for virtual networks and local networks is 10 per subscription, you can request
    an increase limitation by following the article below:
    http://azure.microsoft.com/blog/2014/06/04/azure-limits-quotas-increase-requests/
    If you have anything unclear, please feel free to let me know.
    Best regards,
    Susie
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

  • Hi, what can i use location service for find my lost macbookAir

    hi, what can i use location service for find my lost macbookAir

    If you're an iCloud user and had "Find my Mac" enabled in the System Preferences, then you can go to www.icloud.com, sign in and click Find my iPhone.

  • HT5467 how can i use location services from my pc to find my lost ipod?

    how can i use location services from my pc to find my lost ipod?

    Find My iPod
    http://www.apple.com/sg/icloud/features/find-my-iphone.html

  • ASA 5505 VPN clients can't ping router or other clients on network

    I have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
    Result of the command: "show running-config"
    : Saved
    ASA Version 7.2(4)
    hostname ASA
    domain-name default.domain.invalid
    enable password kdnFT44SJ1UFX5Us encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    name 10.0.0.4 Server
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.0.0.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    clock timezone MST -7
    clock summer-time MDT recurring
    dns domain-lookup inside
    dns domain-lookup outside
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list vpn_splitTunnelAcl standard permit any
    access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
    static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
    static (inside,outside) tcp interface www Server www netmask 255.255.255.255
    static (inside,outside) tcp interface https Server https netmask 255.255.255.255
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable 480
    http 10.0.0.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs group1
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    group-policy vpn internal
    group-policy vpn attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value vpn_splitTunnelAcl
    username admin password wwYXKJulWcFrrhXN encrypted privilege 15
    username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
    username VPNuser attributes
    vpn-group-policy vpn
    tunnel-group vpn type ipsec-ra
    tunnel-group vpn general-attributes
    address-pool VPNpool
    default-group-policy vpn
    tunnel-group vpn ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
    message-length maximum 512
    policy-map global_policy
    class inspection_default
    inspect dns preset_dns_map
    inspect ftp
    inspect h323 h225
    inspect h323 ras
    inspect rsh
    inspect rtsp
    inspect esmtp
    inspect sqlnet
    inspect skinny
    inspect sunrpc
    inspect xdmcp
    inspect sip
    inspect netbios
    inspect tftp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:df7d1e4f34ee0e155cebe86465f367f5
    : end
    Any ideas what I need to add to get the vpn client to be able to ping the router and clients?
    Thanks.

    I tried that and it didn't work. As for upgrading the ASA version, I'd like to but this is an old router and I don't have a support contract with Cisco anymore, so I can't access the latest firmware.
    here is the runnign config again:
    Result of the command: "show startup-config"
    : Saved
    : Written by enable_15 at 01:48:37.789 MDT Wed Jun 20 2012
    ASA Version 7.2(4)
    hostname ASA
    domain-name default.domain.invalid
    enable password kdnFT44SJ1UFX5Us encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    name 10.0.0.4 Server
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.0.0.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address dhcp setroute
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    clock timezone MST -7
    clock summer-time MDT recurring
    dns domain-lookup inside
    dns domain-lookup outside
    dns server-group DefaultDNS
    domain-name default.domain.invalid
    access-list vpn_splitTunnelAcl standard permit any
    access-list inside_nat0_outbound extended permit ip any 10.0.0.192 255.255.255.192
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool VPNpool 10.0.0.220-10.0.0.240 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-524.bin
    asdm location Server 255.255.255.255 inside
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) tcp interface smtp Server smtp netmask 255.255.255.255
    static (inside,outside) tcp interface pop3 Server pop3 netmask 255.255.255.255
    static (inside,outside) tcp interface www Server www netmask 255.255.255.255
    static (inside,outside) tcp interface https Server https netmask 255.255.255.255
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    http server enable 480
    http 10.0.0.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto dynamic-map outside_dyn_map 20 set pfs group1
    crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    group-policy vpn internal
    group-policy vpn attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value vpn_splitTunnelAcl
    username admin password wwYXKJulWcFrrhXN encrypted privilege 15
    username VPNuser password fRPIQoKPyxym36g7 encrypted privilege 15
    username VPNuser attributes
    vpn-group-policy vpn
    tunnel-group vpn type ipsec-ra
    tunnel-group vpn general-attributes
    address-pool VPNpool
    default-group-policy vpn
    tunnel-group vpn ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    Cryptochecksum:78864f4099f215f4ebdd710051bdb493

  • ASA 5505 VPN Ping Problems

    Hello everyone,
    First off, I apologize if this is something that I can google. My knowledge of network administration is all self-taught so if there is a guide to follow that I've missed please point me in the right direction, its often hard to Google terms for troubleshooting when your jargon isn't up to snuff.
    The chief issue is that when pinging internal devices while connected to the results are very inconsistent.
    Pinging 192.168.15.102 with 32 bytes of data:
    Reply from 192.168.15.102: bytes=32 time=112ms TTL=128
    Request timed out.
    Request timed out.
    Request timed out.
    We've set up a IPSec VPN connection to a remote Cisco ASA 5505. There are no issues connecting, connection seems constant, packets good etc. At this point I can only assume I have configuration issues but I've been looking at this for so long, and coupled with my inexperience configuring these settings I have no clue where to start. My initial thoughts are that the LAN devices I am pinging are not sending their response back or the ASA doesn't know how to route packets back?
    Here's a dump of the configuration:
    Result of the command: "show config"
    : Saved
    : Written by enable_15 at 12:40:06.114 CDT Mon Sep 9 2013
    ASA Version 8.2(5)
    hostname VPN_Test
    enable password D37rIydCZ/bnf1uj encrypted
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    name 192.168.15.0 internal-network
    ddns update method DDNS_Update
    ddns both
    interval maximum 0 4 0 0
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    description VLAN to inside hosts
    nameif inside
    security-level 100
    ddns update hostname 0.0.0.0
    ddns update DDNS_Update
    dhcp client update dns server both
    ip address 192.168.15.1 255.255.255.0
    interface Vlan2
    description External VLAN to internet
    nameif outside
    security-level 0
    ip address xx.xx.xx.xx 255.255.255.248
    ftp mode passive
    clock timezone CST -6
    clock summer-time CDT recurring
    dns server-group DefaultDNS
    name-server 216.221.96.37
    name-server 8.8.8.8
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    object-group service DM_INLINE_TCP_1 tcp
    port-object eq www
    port-object eq https
    access-list outside_access_in extended permit icmp any any
    access-list outside_access_in extended deny icmp interface outside interface inside
    access-list outside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
    access-list Remote_splitTunnelAcl standard permit internal-network 255.255.255.0
    access-list inside_nat0_outbound extended permit ip internal-network 255.255.255.0 192.168.15.192 255.255.255.192
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_access_in extended permit ip 192.168.15.192 255.255.255.192 any
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_access_in extended permit ip interface inside interface inside
    access-list inside_access_in extended permit ip any 192.168.15.192 255.255.255.192
    access-list inside_access_in remark Block Internet Traffic
    access-list inside_nat0_outbound_1 extended permit ip 192.168.15.192 255.255.255.192 any
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool VPN_IP_Pool 192.168.15.200-192.168.15.250 mask 255.255.255.0
    ipv6 access-list inside_access_ipv6_in permit ip interface inside interface inside
    icmp unreachable rate-limit 1 burst-size 1
    icmp permit any inside
    icmp permit any echo-reply outside
    icmp permit any outside
    no asdm history enable
    arp timeout 14400
    nat-control
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 0 access-list inside_nat0_outbound_1 outside
    nat (inside) 1 192.168.15.192 255.255.255.192
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group inside_access_in in interface inside
    access-group inside_access_ipv6_in in interface inside
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 xx.xx.xx.xx 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    http internal-network 255.255.255.0 inside
    http yy.yy.yy.yy 255.255.255.255 outside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    sysopt connection timewait
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map outside_map interface outside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd auto_config outside
    dhcpd address 192.168.15.200-192.168.15.250 inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
    ntp server 192.168.15.101 source inside
    ntp server 192.168.15.100 source inside prefer
    webvpn
    group-policy Remote internal
    group-policy Remote attributes
    vpn-tunnel-protocol IPSec
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value Remote_splitTunnelAcl
    username StockUser password t6a0Nv8HUfWtUdKz encrypted privilege 0
    username StockUser attributes
    vpn-group-policy Remote
    tunnel-group Remote type remote-access
    tunnel-group Remote general-attributes
    address-pool VPN_IP_Pool
    default-group-policy Remote
    tunnel-group Remote ipsec-attributes
    pre-shared-key *
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny 
      inspect sunrpc
      inspect xdmcp
      inspect sip 
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:f4271785b86e45dd3a17bab8f60cd2f3

    Hi Graham,
    My first question is do you have a site to site VPN or Remote access client VPN.
    After checking your configuration i see that you do not have any Site to SIte VPN configuration so i am assuming that you ara facing issue with the VPN client.
    And if i understood correctly you are able to connect the VPN client but you not able to access the internal resources properly.
    I would recommend you to tey and make teh following changes.
    Remove the following configuration first:
    nat (inside) 0 access-list inside_nat0_outbound_1 outside
    nat (inside) 1 192.168.15.192 255.255.255.192
    You do not need the 1st one and i do not understand the reason of the second one
    Second one is your pool IP subnet (192.168.15.200-192.168.15.250) and i am not sure why you have added this NAT.
    If possible change your Pool subnet all together because we do not recommend to use th POOL ip which is simlar to your local LAN.
    Try the above changes and let me know in case if you have any issue.
    Thanks
    Jeet Kumar

  • ASA 5505 & VPN Client blocking access to local lan

    I have setup a IPSec vpn client connection to a Cisco ASA 5505, when I connect to the unit it fully authenticates and issues me an ip address on the local lan however when I attempt to connect to any service on the local lan the following message is displayed in the log can you help:
    Teardown UDP connection 192.168.110.200 53785 192.168.110.21 53 outside:192.168.110.200/53785(LOCAL\username) to inside 192.168.110/53
    See the attached file for a sanitised version of the config.

    This is a sanitised version of the crypto dump, I have changed the user and IP addresses
    ASA5505MAN# debug crypto ikev1 7
    ASA5505MAN# debug crypto ipsec 7
    ASA5505MAN# Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=fbc167de) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb72)
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb72)
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=515fbf7e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=2fe7cf10) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb73)
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb73)
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=e450c971) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=e6c212e7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb74)
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb74)
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
    Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
    Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=af5953c7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
    This is the isakmp dump
    ASA5505MAN# show crypto isakmp
    IKEv1 SAs:
       Active SA: 2
        Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
    Total IKE SA: 2
    1   IKE Peer: x.x.x.x
        Type    : L2L             Role    : initiator
        Rekey   : no              State   : MM_ACTIVE
    2   IKE Peer: x.x.x.x
        Type    : user            Role    : responder
        Rekey   : no              State   : AM_ACTIVE
    There are no IKEv2 SAs
    Global IKEv1 Statistics
      Active Tunnels:              1
      Previous Tunnels:           40
      In Octets:              322076
      In Packets:               2060
      In Drop Packets:            84
      In Notifys:               1072
      In P2 Exchanges:            35
      In P2 Exchange Invalids:     0
      In P2 Exchange Rejects:      0
      In P2 Sa Delete Requests:   24
      Out Octets:             591896
      Out Packets:              3481
      Out Drop Packets:            0
      Out Notifys:              2101
      Out P2 Exchanges:          275
      Out P2 Exchange Invalids:    0
      Out P2 Exchange Rejects:     0
      Out P2 Sa Delete Requests: 284
      Initiator Tunnels:         231
      Initiator Fails:           221
      Responder Fails:            76
      System Capacity Fails:       0
      Auth Fails:                 54
      Decrypt Fails:               0
      Hash Valid Fails:            0
      No Sa Fails:                30
    Global IKEv2 Statistics
      Active Tunnels:                          0
      Previous Tunnels:                        0
      In Octets:                               0
      In Packets:                              0
      In Drop Packets:                         0
      In Drop Fragments:                       0
      In Notifys:                              0
      In P2 Exchange:                          0
      In P2 Exchange Invalids:                 0
      In P2 Exchange Rejects:                  0
      In IPSEC Delete:                         0
      In IKE Delete:                           0
      Out Octets:                              0
      Out Packets:                             0
      Out Drop Packets:                        0
      Out Drop Fragments:                      0
      Out Notifys:                             0
      Out P2 Exchange:                         0
      Out P2 Exchange Invalids:                0
      Out P2 Exchange Rejects:                 0
      Out IPSEC Delete:                        0
      Out IKE Delete:                          0
      SAs Locally Initiated:                   0
      SAs Locally Initiated Failed:            0
      SAs Remotely Initiated:                  0
      SAs Remotely Initiated Failed:           0
      System Capacity Failures:                0
      Authentication Failures:                 0
      Decrypt Failures:                        0
      Hash Failures:                           0
      Invalid SPI:                             0
      In Configs:                              0
      Out Configs:                             0
      In Configs Rejects:                      0
      Out Configs Rejects:                     0
      Previous Tunnels:                        0
      Previous Tunnels Wraps:                  0
      In DPD Messages:                         0
      Out DPD Messages:                        0
      Out NAT Keepalives:                      0
      IKE Rekey Locally Initiated:             0
      IKE Rekey Remotely Initiated:            0
      CHILD Rekey Locally Initiated:           0
      CHILD Rekey Remotely Initiated:          0
    IKEV2 Call Admission Statistics
      Max Active SAs:                   No Limit
      Max In-Negotiation SAs:                 12
      Cookie Challenge Threshold:          Never
      Active SAs:                              0
      In-Negotiation SAs:                      0
      Incoming Requests:                       0
      Incoming Requests Accepted:              0
      Incoming Requests Rejected:              0
      Outgoing Requests:                       0
      Outgoing Requests Accepted:              0
      Outgoing Requests Rejected:              0
      Rejected Requests:                       0
      Rejected Over Max SA limit:              0
      Rejected Low Resources:                  0
      Rejected Reboot In Progress:             0
      Cookie Challenges:                       0
      Cookie Challenges Passed:                0
      Cookie Challenges Failed:                0
    Global IKEv1 IPSec over TCP Statistics
    Embryonic connections: 0
    Active connections: 0
    Previous connections: 0
    Inbound packets: 0
    Inbound dropped packets: 0
    Outbound packets: 0
    Outbound dropped packets: 0
    RST packets: 0
    Recevied ACK heart-beat packets: 0
    Bad headers: 0
    Bad trailers: 0
    Timer failures: 0
    Checksum errors: 0
    Internal errors: 0
    ASA5505MAN#
    and this is the ipsec dump
    ASA5505MAN# show crypto ipsec sa
    interface: outside
        Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: x.x.x.x
          local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.110.200/255.255.255.255/0/0)
          current_peer: x.x.x.x, username: username
          dynamic allocated peer ip: 192.168.110.200
          #pkts encaps: 778, #pkts encrypt: 778, #pkts digest: 778
          #pkts decaps: 1959, #pkts decrypt: 1959, #pkts verify: 1959
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 778, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #TFC rcvd: 0, #TFC sent: 0
          #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: x.x.x.x/4500, remote crypto endpt.: x.x.x.x/54599
          path mtu 1500, ipsec overhead 82(52), media mtu 1500
          PMTU time remaining (sec): 0, DF policy: copy-df
          ICMP error validation: disabled, TFC packets: disabled
          current outbound spi: 532B60D0
          current inbound spi : 472C8AE7
        inbound esp sas:
          spi: 0x472C8AE7 (1194101479)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, IKEv1, }
             slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 26551
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0x532B60D0 (1395351760)
             transform: esp-aes esp-sha-hmac no compression
             in use settings ={RA, Tunnel,  NAT-T-Encaps, IKEv1, }
             slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
             sa timing: remaining key lifetime (sec): 26551
             IV size: 16 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
        Crypto map tag: outside_map0, seq num: 1, local addr: x.x.x.x
          access-list outside_cryptomap_1 extended permit ip 192.168.110.0 255.255.255.0 192.168.0.0 255.255.0.0
          local ident (addr/mask/prot/port): (192.168.110.0/255.255.255.0/0/0)
          remote ident (addr/mask/prot/port): (192.168.0.0/255.255.0.0/0/0)
          current_peer: x.x.x.x
          #pkts encaps: 39333117, #pkts encrypt: 39333117, #pkts digest: 39333117
          #pkts decaps: 24914965, #pkts decrypt: 24914965, #pkts verify: 24914965
          #pkts compressed: 0, #pkts decompressed: 0
          #pkts not compressed: 39333117, #pkts comp failed: 0, #pkts decomp failed: 0
          #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
          #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
          #TFC rcvd: 0, #TFC sent: 0
          #Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
          #send errors: 0, #recv errors: 0
          local crypto endpt.: x.x.x.x/0, remote crypto endpt.: x.x.x.x/0
          path mtu 1500, ipsec overhead 58(36), media mtu 1500
          PMTU time remaining (sec): 0, DF policy: copy-df
          ICMP error validation: disabled, TFC packets: disabled
          current outbound spi: F6943017
          current inbound spi : E6CDF924
        inbound esp sas:
          spi: 0xE6CDF924 (3872258340)
             transform: esp-3des esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, IKEv1, }
             slot: 0, conn_id: 163840, crypto-map: outside_map0
             sa timing: remaining key lifetime (kB/sec): (3651601/15931)
             IV size: 8 bytes
             replay detection support: Y
             Anti replay bitmap:
              0xFFFFFFFF 0xFFFFFFFF
        outbound esp sas:
          spi: 0xF6943017 (4136906775)
             transform: esp-3des esp-sha-hmac no compression
             in use settings ={L2L, Tunnel, IKEv1, }
             slot: 0, conn_id: 163840, crypto-map: outside_map0
             sa timing: remaining key lifetime (kB/sec): (3561355/15931)
             IV size: 8 bytes
             replay detection support: Y
             Anti replay bitmap:
              0x00000000 0x00000001
    ASA5505MAN#

  • ASA 5505 rookie - can't ping remote site or vice versa

    Hi, I'm trying to setup an ipsec from an ASA 5505 (8.4) to a Sophos UTM (9.2)
    Internet etc is up and accessible. Ipsec tunnel is up also but I can't pass traffic through it.
    I get this message in the logs:
    3
    Aug 05 2014
    22:38:52
    81.111.111.156
    82.222.222.38
    Deny inbound protocol 50 src outside:81.111.111.156 dst outside:82.222.222.38
    SITE A (ASA 5505) = 82.222.222.38
    SITE B (UTM 9) = 81.111.111.156
    Any pointers would be good as this is the first time I've tried this. Thank you.
    Running config below:
    hostname ciscoasa
    enable password 8Ry2YjIyt7RRXU24 encrypted
    xlate per-session deny tcp any4 any4
    xlate per-session deny tcp any4 any6
    xlate per-session deny tcp any6 any4
    xlate per-session deny tcp any6 any6
    xlate per-session deny udp any4 any4 eq domain
    xlate per-session deny udp any4 any6 eq domain
    xlate per-session deny udp any6 any4 eq domain
    xlate per-session deny udp any6 any6 eq domain
    passwd 2KFQnbNIdI.2KYOU encrypted
    names
    interface Ethernet0/0
     switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
     nameif inside
     security-level 100
     ip address 192.168.1.1 255.255.255.0
    interface Vlan2
     description Zen Internet
     nameif outside
     security-level 0
     pppoe client vpdn group Zen
     ip address 82.222.222.38 255.255.255.255 pppoe setroute
    boot system disk0:/asa922-k8.bin
    ftp mode passive
    dns domain-lookup inside
    dns domain-lookup outside
    dns server-group DefaultDNS
     name-server 8.8.8.8
    object network obj_any
     subnet 0.0.0.0 0.0.0.0
    object network MY-LAN
     subnet 192.168.1.0 255.255.255.0
    object network THIER-LAN
     subnet 192.168.30.0 255.255.255.0
    object network NETWORK_OBJ_192.168.1.0_24
     subnet 192.168.1.0 255.255.255.0
    object network NETWORK_OBJ_192.168.30.0_24
     subnet 192.168.30.0 255.255.255.0
    object network THIER_VPN
     host 81.111.111.156
     description THIER VPN 
    object service Sophos_Admin
     service tcp destination eq 4444
    object-group protocol DM_INLINE_PROTOCOL_1
     protocol-object ip
     protocol-object icmp
     protocol-object esp
    object-group protocol DM_INLINE_PROTOCOL_2
     protocol-object ip
     protocol-object icmp
     protocol-object esp
    object-group protocol DM_INLINE_PROTOCOL_3
     protocol-object ip
     protocol-object icmp
     protocol-object esp
    object-group service DM_INLINE_SERVICE_1
     service-object icmp
     service-object udp destination eq domain
     service-object object Sophos_Admin
     service-object tcp destination eq www
     service-object tcp destination eq https
     service-object esp
    object-group service DM_INLINE_SERVICE_2
     service-object icmp
     service-object object Sophos_Admin
     service-object esp
     service-object icmp echo-reply
    object-group service DM_INLINE_SERVICE_3
     service-object ip
     service-object esp
     service-object icmp echo-reply
    object-group service DM_INLINE_SERVICE_4
     service-object object Sophos_Admin
     service-object icmp echo
     service-object icmp echo-reply
    access-list outside_cryptomap extended permit object-group DM_INLINE_PROTOCOL_3 object MY-LAN object THIER-LAN
    access-list outside_cryptomap_1 extended permit object-group DM_INLINE_PROTOCOL_2 object MY-LAN object THIER-LAN
    access-list inside_cryptomap extended permit object-group DM_INLINE_PROTOCOL_1 object THIER-LAN object MY-LAN
    access-list outside_access_out extended permit object-group DM_INLINE_SERVICE_3 object THIER_VPN host 82.222.222.38
    access-list outside_access_out extended permit object-group DM_INLINE_SERVICE_1 any any
    access-list outside_access_in extended permit object-group DM_INLINE_SERVICE_2 object THIER_VPN host 82.222.222.38
    access-list inside_access_out extended permit object-group DM_INLINE_SERVICE_4 object MY-LAN object THIER-LAN
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-722.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    object network obj_any
     nat (inside,outside) dynamic interface
    access-group inside_access_out out interface inside
    access-group outside_access_in in interface outside
    access-group outside_access_out out interface outside
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    aaa authentication http console LOCAL
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
    crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
    crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
    crypto ipsec ikev2 ipsec-proposal DES
     protocol esp encryption des
     protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal 3DES
     protocol esp encryption 3des
     protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES
     protocol esp encryption aes
     protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES192
     protocol esp encryption aes-192
     protocol esp integrity sha-1 md5
    crypto ipsec ikev2 ipsec-proposal AES256
     protocol esp encryption aes-256
     protocol esp integrity sha-1 md5
    crypto ipsec security-association pmtu-aging infinite
    crypto map outside_map 1 match address outside_cryptomap
    crypto map outside_map 1 set pfs
    crypto map outside_map 1 set peer 81.111.111.156
    crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA
    crypto map outside_map 1 set ikev2 ipsec-proposal AES
    crypto map outside_map 2 match address outside_cryptomap_1
    crypto map outside_map 2 set pfs
    crypto map outside_map 2 set peer 81.111.111.156
    crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
    crypto map outside_map interface outside
    crypto ca trustpool policy
    crypto ikev2 policy 20
     encryption aes
     integrity sha
     group 2
     prf sha
     lifetime seconds 7800
    crypto ikev2 enable outside
    crypto ikev1 enable outside
    crypto ikev1 policy 90
     authentication pre-share
     encryption aes
     hash sha
     group 2
     lifetime 7800
    telnet timeout 5
    ssh scopy enable
    ssh stricthostkeycheck
    ssh 192.168.1.0 255.255.255.0 inside
    ssh timeout 30
    ssh version 2
    ssh key-exchange group dh-group1-sha1
    console timeout 0
    vpdn group Zen request dialout pppoe
    vpdn group Zen localname MYISP@zen
    vpdn group Zen ppp authentication chap
    vpdn username MYISP@zen password ***** store-local
    dhcpd auto_config outside
    dhcpd address 192.168.1.5-192.168.1.36 inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    dynamic-filter updater-client enable
    dynamic-filter use-database
    dynamic-filter enable interface outside
    dynamic-filter drop blacklist interface outside
    webvpn
     anyconnect-essentials
    group-policy GroupPolicy_81.111.111.156 internal
    group-policy GroupPolicy_81.111.111.156 attributes
     vpn-tunnel-protocol ikev1
    username admin password JsE9Hv42G/zRUcG4 encrypted privilege 15
    username bob password lTKS32e90Yo5l2L/ encrypted
    tunnel-group 81.111.111.156 type ipsec-l2l
    tunnel-group 81.111.111.156 general-attributes
     default-group-policy GroupPolicy_81.111.111.156
    tunnel-group 81.111.111.156 ipsec-attributes
     ikev1 pre-shared-key *****
     ikev2 remote-authentication pre-shared-key *****
     ikev2 local-authentication pre-shared-key *****
    class-map inspection_default
     match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
     parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
     class inspection_default
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
      inspect dns preset_dns_map dynamic-filter-snoop
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    hpm topN enable
    Cryptochecksum:9430c8a44d330d2b55f981274599a67e
    : end
    ciscoasa#

    Hi,
    I started again and used various combinations of encryption etc but they all come back the same so I'm at a loss.
    output of debug crypto ipsec 128
    IPSEC: New embryonic SA created @ 0xcdbaeff8,
        SCB: 0xCDC33C70,
        Direction: inbound
        SPI      : 0x6699A5F8
        Session ID: 0x00006000
        VPIF num  : 0x00000003
        Tunnel type: l2l
        Protocol   : esp
        Lifetime   : 240 seconds
    IPSEC: New embryonic SA created @ 0xcdc76048,
        SCB: 0xCDB97B98,
        Direction: outbound
        SPI      : 0xB4E5EBD5
        Session ID: 0x00006000
        VPIF num  : 0x00000003
        Tunnel type: l2l
        Protocol   : esp
        Lifetime   : 240 seconds
    IPSEC: Completed host OBSA update, SPI 0xB4E5EBD5
    IPSEC: Creating outbound VPN context, SPI 0xB4E5EBD5
        Flags: 0x00000005
        SA   : 0xcdc76048
        SPI  : 0xB4E5EBD5
        MTU  : 1492 bytes
        VCID : 0x00000000
        Peer : 0x00000000
        SCB  : 0x3653C7F5
        Channel: 0xc8c234e0
    IPSEC: Completed outbound VPN context, SPI 0xB4E5EBD5
        VPN handle: 0x0003820c
    IPSEC: New outbound encrypt rule, SPI 0xB4E5EBD5
        Src addr: 192.168.1.0
        Src mask: 255.255.255.0
        Dst addr: 192.168.30.0
        Dst mask: 255.255.255.0
        Src ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Dst ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Protocol: 0
        Use protocol: false
        SPI: 0x00000000
        Use SPI: false
    IPSEC: Completed outbound encrypt rule, SPI 0xB4E5EBD5
        Rule ID: 0xca9505d8
    IPSEC: New outbound permit rule, SPI 0xB4E5EBD5
        Src addr: 88.222.222.38
        Src mask: 255.255.255.255
        Dst addr: 80.111.111.156
        Dst mask: 255.255.255.255
        Src ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Dst ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Protocol: 50
        Use protocol: true
        SPI: 0xB4E5EBD5
        Use SPI: true
    IPSEC: Completed outbound permit rule, SPI 0xB4E5EBD5
        Rule ID: 0xcdc482c8
    IPSEC: New embryonic SA created @ 0xcdbaeff8,
        SCB: 0xCDC33C70,
        Direction: inbound
        SPI      : 0x6699A5F8
        Session ID: 0x00006000
        VPIF num  : 0x00000003
        Tunnel type: l2l
        Protocol   : esp
        Lifetime   : 240 seconds
    IPSEC: Completed host IBSA update, SPI 0x6699A5F8
    IPSEC: Creating inbound VPN context, SPI 0x6699A5F8
        Flags: 0x00000006
        SA   : 0xcdbaeff8
        SPI  : 0x6699A5F8
        MTU  : 0 bytes
        VCID : 0x00000000
        Peer : 0x0003820C
        SCB  : 0x363F2BE7
        Channel: 0xc8c234e0
    IPSEC: Completed inbound VPN context, SPI 0x6699A5F8
        VPN handle: 0x00040e4c
    IPSEC: Updating outbound VPN context 0x0003820C, SPI 0xB4E5EBD5
        Flags: 0x00000005
        SA   : 0xcdc76048
        SPI  : 0xB4E5EBD5
        MTU  : 1492 bytes
        VCID : 0x00000000
        Peer : 0x00040E4C
        SCB  : 0x3653C7F5
        Channel: 0xc8c234e0
    IPSEC: Completed outbound VPN context, SPI 0xB4E5EBD5
        VPN handle: 0x0003820c
    IPSEC: Completed outbound inner rule, SPI 0xB4E5EBD5
        Rule ID: 0xca9505d8
    IPSEC: Completed outbound outer SPD rule, SPI 0xB4E5EBD5
        Rule ID: 0xcdc482c8
    IPSEC: New inbound tunnel flow rule, SPI 0x6699A5F8
        Src addr: 192.168.30.0
        Src mask: 255.255.255.0
        Dst addr: 192.168.1.0
        Dst mask: 255.255.255.0
        Src ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Dst ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Protocol: 0
        Use protocol: false
        SPI: 0x00000000
        Use SPI: false
    IPSEC: Completed inbound tunnel flow rule, SPI 0x6699A5F8
        Rule ID: 0xcdc35348
    IPSEC: New inbound decrypt rule, SPI 0x6699A5F8
        Src addr: 80.111.111.156
        Src mask: 255.255.255.255
        Dst addr: 88.222.222.38
        Dst mask: 255.255.255.255
        Src ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Dst ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Protocol: 50
        Use protocol: true
        SPI: 0x6699A5F8
        Use SPI: true
    IPSEC: Completed inbound decrypt rule, SPI 0x6699A5F8
        Rule ID: 0xc96f7cc8
    IPSEC: New inbound permit rule, SPI 0x6699A5F8
        Src addr: 80.111.111.156
        Src mask: 255.255.255.255
        Dst addr: 88.222.222.38
        Dst mask: 255.255.255.255
        Src ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Dst ports
          Upper: 0
          Lower: 0
          Op   : ignore
        Protocol: 50
        Use protocol: true
        SPI: 0x6699A5F8
        Use SPI: true
    IPSEC: Completed inbound permit rule, SPI 0x6699A5F8
        Rule ID: 0xc96f6388

  • ASA 5505 VPN HELP!!!

    I have two ASA 5505's.  One is currently setup as my firewall connected to the Cox Cable modem and wireless AP.  I have another ASA that I would like to use, I have an idea that I could set that one up as a VPN unit, but not sure how I could do that.  If that is not an option, can you provide the command line instructions on how to setup the VPN via the console cable.  I am kinda new and I am slowing trying to become more knowledgeable about this.  Any help would be greatly appreciated.
    Thanks,
    Jon
    My current Config:
    ASA Version 8.2(3)wn coldstart' comm
    !d
    hostname Wood-ASA1-if
    %ASA-5-111008:
    domain-name lv.cox.net the 'inspect ip-optio
    enable password 8Ry2YjIyt7RRXU24 encrypted8cb69fe 20cfb60adisk0:/asa823.bin      
    passwd 2KFQnbNIdI.2KYOU encrypteded the 'service-policy global_pol
    namesobal'
    !a
    interface Ethernet0/0in        ^         
    switchport access vlan 2%ASA-5-
    command.ser 'Con
    !S
    interface Ethernet0/1ig' executed the 'pro
    !t
    interface Ethernet0/2mand.tics access-lirv
    interface Ethernet0/3 securi
    rd DfltAccess
    !l
    interface Etherne              
    interface Vlan1ecuted the 'pro
    nameif inside' command.omma
    security-level 100
    %ASA-5-111008: Use
    ip address 192.168.1.1 255.255.255.01008: User 'Config' executed the 'no
    !t
    interface Vlan2 the '
    %ASA-5-1
    nameif outsidefig' executed t
    security-level 0-5-111008: User '
    ip address dhcp setrouteination address http http
    boot system disk0:/asa823-k8.bing' executed the 'class-map inspe
    boot config disk0:/asa823.binom/its/service/oddce/services
    ftp mode passivemand. User 'Conf
    dns server-group DefaultDNS User 'Config' execut
    %ASA-
    domain-name lv.cox.netexecuted the 'destinati
    object-group icmp-type ICMP-INBOUNDation linkup linkdown coldstart' co
    description Permit necessary inbound ICMP trafficand.'policy-map type
    %ASA-5-111008: User 'Config'
    icmp-object echo-replyon transport-method htt
    icmp-object unreachable
    s_map' command.t
    icmp-object t            
    %ASA-
    logging buffered warningsecuted the 'subscribe-to-
    logging asdm notificationsxecuted t
    %ASA-5-111008: U
    mtu inside 1500cuted the 'poli
    mtu outside 1500ct
    riodic month
    icmp unreachable rate-limit 1 burst-size 1-111008: User 'Config' executed the 'subsc
    asdm image disk0:/asdm-625.bino5-111008: User 'Config' execu
    no asdm history enablemmand.outside' command
    arp timeout 14400monthly' command.
    nat-control
    %ASA-5-111
    global (outside) 1 interfacenfig' executed the 'subscrib
    nat (inside) 1 0.0.0.0 0.0.0.0andasa# threat-detec
    d.n
    %ASA
    access-group INBOUND in interface outside08: Us
    riodic daily' command.e          
    timeout xlate 3:             
    aaa authentication ssh console LOCALe Ethernet0/5, changed state to admi
    http server enableas
    %ASA-5-111008:
    http 192.168.1.0 255.255.255.0 inside' executed the
    %ASA-4-411003: Interfa
    no snmp-server locationstate to administra con
    no snmp-server contact                     
    telnet timeout 5# nat-contr
    %ASA
    ssh 0.0.0.0 0.0.0.0 insideec
    %ASA-4-411001: Line pro
    ssh 0.0.0.0 0.0.0.0 outside/3, changed state to upomma
    ssh timeout 5SA-5-111
    %ASA
    console timeout 0onfig' executed t
    dhcpd dns 8.8.8.8 8.8.4.4ne protocol on Interface
    dhcpd auto_config outside to ups_map' com
    %ASA-5-1
    !0
    dhcpd address 192.168.1.2-192.168.1.33 insideommand
    enableR: % I
    Password:SA-5-1110
    Wood-A
    dhcpd dns 8.8.8.8 8.8.4.4 interface inside: Uname: enable_15 From: 1 To:pect netbios
    dhcpd enable insidescoas
    %ASA-5-111008
    !U
    threat-detection basic-threat%ASA-5-111008: User 'enable_1
    threat-detection statistics acce
    .0.0.0 0.0.0.        
    parametersprompt host
      message-length maximum client auto1008: User 'enable_15' executed the
      message-length maximum 512A-5-111008: User 'Config' ex
    policy-map type inspect dns prsent_dns_map 0/0' command. executed the 'inspe
    no shut
    parametersA-5
    Wood-AS
      message-length maximum 512 Interface Ethernet0/0, chan
    policy-map global_policyg' executed the 'inspect
    class inspection_defaultA-5-111008: User 'Con
    ini
      inspect dns preset_dns_map
    %ASA-5-111008: User 'enable
      inspect ftpthe 'no shutd
      inspect h323 h225111008: User 'Confi
      inspect h323 rasstination address
      inspect rsh1001: Line pr
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    call-home
    profile CiscoTAC-1
      no active
      destination address http https://tools.cisco.com/its/service/oddce/services/DD
    CEService
      destination address email [email protected]
      destination transport-method http
      subscribe-to-alert-group diagnostic
      subscribe-to-alert-group environment
      subscribe-to-alert-group inventory periodic monthly
      subscribe-to-alert-group configuration periodic monthly
      subscribe-to-alert-group telemetry periodic daily
    Cryptochecksum:c3a35118ab34143a5e73e414ead343c1

    for sure you can do this with the ASA , see the following configuration example :
    http://www.cisco.com/en/US/partner/products/ps6120/products_configuration_example09186a0080950890.shtml
    cheers.

  • ASA 5505 vpn/OWA issue

    I have a client that is running Win2003 Server R2 with Exchange Server 2003. OWA was setup and clients could connect to their exchange mailbox from the internet with no problems.
    We recently configured vpn on the ASA 5505 and now no-one can connect to OWA since that time.
    Any thoughts?

    Have you been using the ASDM to configure the VPN? In that case, you may have removed the required portforwarding or modified the access-list that allows traffic from the outside.
    regards,
    Leo

Maybe you are looking for

  • Csv no data found when using bind variables

    Hi, I have created a report, that uses 2 date variables to limit the query and rows display as they should. But clicking the csv link opens csv having one row stating 'No data found...'. If I set static values in place of variables, I get the right r

  • EJB 3.0 Preview - Security

    I was trying to use standard JDK annotations for securing EJB methods. At the time of compiling my EJB using weblogic.appc, I am getting the following error.Please let me know if anybody has a solution to this. Error processing annotations: java.lang

  • How do you listen to music that was on your iphone and ended up in the cloud, and is no longer on the phone

    daughters iphone 4 had an update, in the process of the update all of her music and apps went into the icloud. How do we get these back on her phone and out of the cloud.

  • View controller active after navigating via outbound plug, is this normal

    Hallo, I have two components (comp_a,comp_b). comp_a->grid_view_a : fires a event. comp_b->grid_view_b : subscribe to the above event. My observation is that When comp_a->grid_view_a fires a event and comp_b->grid_view_b listen to that event and the

  • 4200v2 looses wireless connection after 24hrs

    Hello All I upgraded my Linksys from 160n router to 4200V2 router.  I configured 3 wireless Linksys webcams and they work fine. After 24hrs they i cannnot connect the via HTTP and webcames IP addresses disapear from the DHCP client table.  If reboot