Asa 8.44 l2l setup: ikev1 or ikev2?
For site to site vpn which should i use? I understand the ikev1 is the vpn client and that ikev2 is for anyconnect, but in the world of just basic site to site, which one do you use?
Ikev does not seem to have an option for the transform set.
Sent from Cisco Technical Support iPad App
You can use either ikev1 or ikev2 for site-to-site vpn tunnel.
If you want to configure it the same way as you use to configure it, it should be ikev1.
However, if you want to use the new version of ike then use ikev2, and here is the sample configuration:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a0080bb8500.shtml
However both end needs to run the same version of ike.
If one end doesn't support ikev2, then you must use ikev1 or the old type of ike to configure it.
Similar Messages
-
Help needed in ASA 5540 Cluster/Failover setup
Hello expert,
Currently we have two asa in our Datacenter setup as a Active/Standby failover setup and tested ie failover is working,(if one FW goes down), but what if a the uplink switches/links or backend switches go down, how does the active fw knows to failover ?
Current setup
| |
___|___ __|___
---| SW 1 |------------------------ | Sw2 |
| |
___|___ __|___
---| FW 1 |------------------------ | FW-2 |
| |
___|___ __|___
---| SW 1 |------------------------ | Sw2 |
In the above figure, FW1 is active and I have powerd off the uplink SW1, but the FW2 did not take over, and the same for backend switches, So how do I configure my FW's so that any of the uplink or back end switches go down, the Active should give its role to standby to forward the traffice from a different switch ie sw2 in case sw1 goes down.
Or Is there any mechanisim where I can monitor the interfaces ie uplinks or back end links etc ?
Your help is appreciated.
RegardsIt seems that you have LAN link directly connected between the boxes, so the unit will determine that Primary/Active has interfaces that are inactive and failover. You should read:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00807dac5f.shtml
This link gives you the failover triggers and failover actions. -
Two ASA IPVPN tunnel ikev1 and ikev2
Dear
I have using 2 ASA 5510 to make IPVPN tunnel. From my experience. I tried to used ONLY ikev1 are working fine. or I tried to used ONLY ikev2 are working fine for the tunnel connection. So, any suggestion for me to keep using ikev1 or need to change to ikev2 instead?Hello,
That's one of the most important actually.
I will provide you a great post about it where Cisco talks about Why should we all migrate
http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a0080bca116.shtml
Let me know if u have any other question bud
Rate all of the helpful posts!!!
Regards,
Jcarvaja
Follow me on http://laguiadelnetworking.com -
How to setup an ikev2 VPN with public key authentication with your BB10 device
This setup will allow you to run a VPN between your BB10.2 (and probably BB10.1) device and a debian linux computer (I am running the testing stream). You will need to tweak this config (and possibly install strongswan server on your LAN's gateway) to get access to network resources, or access the internet via the VPN. I have created this setup with the intention of accessing files/services on the debian computer only.
1. Install strongswan on your debian machine(I have v4.6.4 installed, I think the current testing version is v5.1. If you install v5+, some lines in the config may be obsolete), and install any other extra packages you are prompted to install:
apt-get install strongswan strongswan-ikev1 strongswan-ikev2 strongswan-starter openssl ipsec-tools
2. Generate certificates on your debian server in any, starting with a certificate authority. Edit the C= O= CN= fields to whatever you want:
ipsec pki --gen --outform pem > caKey.pem
ipsec pki --self --in caKey.pem --dn "C=CA, O=none, CN=Certificate-Auth" --san="Certificate-Auth" --ca --outform pem > caCert.pem
Generate a server keypair (again, editing the same fields as I indicated above. The CN= field should be lan ip address of your strongswan server. I would also put this as the address in --san=, or you can specify your hostname(if you have one, i.e. mydomainname.com):
ipsec pki --gen --outform pem > serverKey.pem
ipsec pki --pub --in serverKey.pem | ipsec pki --issue --cacert caCert.pem --cakey caKey.pem --dn "C=CA, O=none, CN=192.168.1.100" --san="192.168.1.100" --flag serverAuth --outform pem > serverCert.pem
Generate a keypair for your BB10 device (choose a CN=, and use it in the --san field @your server lan ip or hostname:
ipsec pki --gen --outform pem > userKey.pem
ipsec pki --pub --in userKey.pem | ipsec pki --issue --cacert caCert.pem --cakey caKey.pem --dn "C=CA, O=none, CN=bb10" --san "[email protected]" --flag serverAuth --outform pem > userCert.pem
3. After generating your keys, package the client keys for your BB10 device(you will be asked to create a password): openssl pkcs12 -export -in userCert.pem -inkey userKey.pem -out bb10.pfx
Copy the bb10.pfx file, and serverCert.pem to your BB10 device and import the certificates into the certificate store(Open Settings --> Security and Privacy --> Certificates --> Import)
4. Move the certificates into the appropriate folders on your debian server:
mv caKey.pem /etc/ipsec.d/private
mv caCert.pem /etc/ipsec.d/cacerts
mv serverKey.pem /etc/ipsec.d/private
mv serverCert.pem /etc/ipsec.d/certs
5. Enable ip forwarding on your debian machine:
edit /etc/sysctl.conf - change the following value as follows:
net.ipv4.ip_forward=1
Close the file and save changes. To enable changes, type: sysctl -p /etc/sysctl.conf
6. Edit config files:
ipsec.secrets:
: RSA serverKey.pem
ipsec.conf:
config setup
strictcrlpolicy=no
uniqueids=yes
conn %default
ikelifetime=60m
keylife=20m
rekeymargin=3m
keyingtries=1
keyexchange=ikev2
leftfirewall=yes
dpddelay=30
dpdtimeout=120
dpdaction=clear
conn bb10
mobike=yes
ike=aes256-sha1-sha1-modp1024!
esp=aes256-sha1!
left=%defaultroute
leftid="C=CA, O=none, CN=192.168.1.100"
leftcert=serverCert.pem
right=%any
rightsourceip=10.10.0.1
rightid="C=CA, O=none, CN=bb10"
rightauth=pubkey
leftauth=pubkey
pfs=yes
auto=add
7. Start the ipsec service on your debian machine: service ipsec stop; service ipsec start
8. Set up the VPN connection on your blackberry: Settings -->Network Connections --> VPN --> Add.
a) Profile Name: Give your VPN a name
b) Server Address: Enter your server's address
c) Gateway Type: Generic IKEv2 VPN Server
d) Authentication Type: PKI
e) Authentication ID Type: Identity Certificate Distinguished Name
f) Client Certificate: The client certificate you imported should show up in the dropdown
g) Gateway Auth Type: PKI
h) Gateway Auth ID Type: Identity Certificate Distinguished Name
i) Gateway CA Certificate: Find the certificate authority you imported. If you used the same name as I did above when creating the certificate, if will be called "Certificate-Auth".
j) Perfect forward secrecy : ON
k) Change IKE Lifetime to 3600
l) Change IPSEC lifetime to 1200
You can leave everything else on default settings. Save your VPN profile.
9. Connect to your VPN. You should now be able to ping both ways between your blackberry and debian host. Using the above configuration, your blackberry device will have the ip address of 10.10.0.1.There have been numerous bb10 updates (now 10.2.1.2977) since I first posted this mini how-to-I am not sure if it was the bb10 updates, or updates to strongswan (now v5.2.0) or my linux kernel (v3.15.3), though I am now able to use stronger hash and elliptic curve key exchange. I am using sha384 in my example, though have also got it working with sha512. Give it a try:
Simply use the same process I detailed before, though change the following lines in ipsec.conf:
ike=aes256-sha1-sha1-modp1024!
esp=aes256-sha1!
to
ike=aes256-sha384-ecp521
esp=aes256-sha384-ecp521
Be sure to restart strongswan after you change these lines in the config.
After this is done, change 'Automatically determine algorithm' to off in the VPN profile settings of your VPN connection profile on your blackberry. I'm not sure why it doesn't work automatically. State the following in this section:
IKE DH Group: 21
IKE CIpher: AES (256-bit key)
IKE Hash: SHA384
IKE PRF: HMAC-SHA384
IPSec DH Group: 21
IPSec Cipher: AES (256-bit key)
IPSec Hash: SHA384 -
How to setup netflow V9 on ASA
Hi Forumers'
want to check out how to configure the ASA to support netflow V9, either in ASDM or CLI mode as welcome.
i follow the PRTG guide it doens't seem success to make the detection on netflow activity,
please advice
NoelHello Joel,
This video should help you confirm that the ASA NetFlow configuration is setup correctly.
Jake -
ASA 5505 & VPN Client blocking access to local lan
I have setup a IPSec vpn client connection to a Cisco ASA 5505, when I connect to the unit it fully authenticates and issues me an ip address on the local lan however when I attempt to connect to any service on the local lan the following message is displayed in the log can you help:
Teardown UDP connection 192.168.110.200 53785 192.168.110.21 53 outside:192.168.110.200/53785(LOCAL\username) to inside 192.168.110/53
See the attached file for a sanitised version of the config.This is a sanitised version of the crypto dump, I have changed the user and IP addresses
ASA5505MAN# debug crypto ikev1 7
ASA5505MAN# debug crypto ipsec 7
ASA5505MAN# Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=fbc167de) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb72)
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:03 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:03 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=515fbf7e) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=2fe7cf10) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb73)
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:18 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:18 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=e450c971) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE RECEIVED Message (msgid=e6c212e7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, processing notify payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Received keep-alive of type DPD R-U-THERE (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, Sending keep-alive of type DPD R-U-THERE-ACK (seq number 0xa6dcb74)
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing blank hash payload
Jul 24 15:49:28 [IKEv1 DEBUG]Group = VPN-Users, Username = username, IP = x.x.x.x, constructing qm hash payload
Jul 24 15:49:28 [IKEv1]IP = x.x.x.x, IKE_DECODE SENDING Message (msgid=af5953c7) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
This is the isakmp dump
ASA5505MAN# show crypto isakmp
IKEv1 SAs:
Active SA: 2
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 2
1 IKE Peer: x.x.x.x
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
2 IKE Peer: x.x.x.x
Type : user Role : responder
Rekey : no State : AM_ACTIVE
There are no IKEv2 SAs
Global IKEv1 Statistics
Active Tunnels: 1
Previous Tunnels: 40
In Octets: 322076
In Packets: 2060
In Drop Packets: 84
In Notifys: 1072
In P2 Exchanges: 35
In P2 Exchange Invalids: 0
In P2 Exchange Rejects: 0
In P2 Sa Delete Requests: 24
Out Octets: 591896
Out Packets: 3481
Out Drop Packets: 0
Out Notifys: 2101
Out P2 Exchanges: 275
Out P2 Exchange Invalids: 0
Out P2 Exchange Rejects: 0
Out P2 Sa Delete Requests: 284
Initiator Tunnels: 231
Initiator Fails: 221
Responder Fails: 76
System Capacity Fails: 0
Auth Fails: 54
Decrypt Fails: 0
Hash Valid Fails: 0
No Sa Fails: 30
Global IKEv2 Statistics
Active Tunnels: 0
Previous Tunnels: 0
In Octets: 0
In Packets: 0
In Drop Packets: 0
In Drop Fragments: 0
In Notifys: 0
In P2 Exchange: 0
In P2 Exchange Invalids: 0
In P2 Exchange Rejects: 0
In IPSEC Delete: 0
In IKE Delete: 0
Out Octets: 0
Out Packets: 0
Out Drop Packets: 0
Out Drop Fragments: 0
Out Notifys: 0
Out P2 Exchange: 0
Out P2 Exchange Invalids: 0
Out P2 Exchange Rejects: 0
Out IPSEC Delete: 0
Out IKE Delete: 0
SAs Locally Initiated: 0
SAs Locally Initiated Failed: 0
SAs Remotely Initiated: 0
SAs Remotely Initiated Failed: 0
System Capacity Failures: 0
Authentication Failures: 0
Decrypt Failures: 0
Hash Failures: 0
Invalid SPI: 0
In Configs: 0
Out Configs: 0
In Configs Rejects: 0
Out Configs Rejects: 0
Previous Tunnels: 0
Previous Tunnels Wraps: 0
In DPD Messages: 0
Out DPD Messages: 0
Out NAT Keepalives: 0
IKE Rekey Locally Initiated: 0
IKE Rekey Remotely Initiated: 0
CHILD Rekey Locally Initiated: 0
CHILD Rekey Remotely Initiated: 0
IKEV2 Call Admission Statistics
Max Active SAs: No Limit
Max In-Negotiation SAs: 12
Cookie Challenge Threshold: Never
Active SAs: 0
In-Negotiation SAs: 0
Incoming Requests: 0
Incoming Requests Accepted: 0
Incoming Requests Rejected: 0
Outgoing Requests: 0
Outgoing Requests Accepted: 0
Outgoing Requests Rejected: 0
Rejected Requests: 0
Rejected Over Max SA limit: 0
Rejected Low Resources: 0
Rejected Reboot In Progress: 0
Cookie Challenges: 0
Cookie Challenges Passed: 0
Cookie Challenges Failed: 0
Global IKEv1 IPSec over TCP Statistics
Embryonic connections: 0
Active connections: 0
Previous connections: 0
Inbound packets: 0
Inbound dropped packets: 0
Outbound packets: 0
Outbound dropped packets: 0
RST packets: 0
Recevied ACK heart-beat packets: 0
Bad headers: 0
Bad trailers: 0
Timer failures: 0
Checksum errors: 0
Internal errors: 0
ASA5505MAN#
and this is the ipsec dump
ASA5505MAN# show crypto ipsec sa
interface: outside
Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: x.x.x.x
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (192.168.110.200/255.255.255.255/0/0)
current_peer: x.x.x.x, username: username
dynamic allocated peer ip: 192.168.110.200
#pkts encaps: 778, #pkts encrypt: 778, #pkts digest: 778
#pkts decaps: 1959, #pkts decrypt: 1959, #pkts verify: 1959
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 778, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x/4500, remote crypto endpt.: x.x.x.x/54599
path mtu 1500, ipsec overhead 82(52), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: 532B60D0
current inbound spi : 472C8AE7
inbound esp sas:
spi: 0x472C8AE7 (1194101479)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (sec): 26551
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x532B60D0 (1395351760)
transform: esp-aes esp-sha-hmac no compression
in use settings ={RA, Tunnel, NAT-T-Encaps, IKEv1, }
slot: 0, conn_id: 241664, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
sa timing: remaining key lifetime (sec): 26551
IV size: 16 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Crypto map tag: outside_map0, seq num: 1, local addr: x.x.x.x
access-list outside_cryptomap_1 extended permit ip 192.168.110.0 255.255.255.0 192.168.0.0 255.255.0.0
local ident (addr/mask/prot/port): (192.168.110.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.0.0/255.255.0.0/0/0)
current_peer: x.x.x.x
#pkts encaps: 39333117, #pkts encrypt: 39333117, #pkts digest: 39333117
#pkts decaps: 24914965, #pkts decrypt: 24914965, #pkts verify: 24914965
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 39333117, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x/0, remote crypto endpt.: x.x.x.x/0
path mtu 1500, ipsec overhead 58(36), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: F6943017
current inbound spi : E6CDF924
inbound esp sas:
spi: 0xE6CDF924 (3872258340)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 163840, crypto-map: outside_map0
sa timing: remaining key lifetime (kB/sec): (3651601/15931)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xF6943017 (4136906775)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 163840, crypto-map: outside_map0
sa timing: remaining key lifetime (kB/sec): (3561355/15931)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
ASA5505MAN# -
Site to Site VPN Between Two ASA 5505's Up But Not Passing Traffic
hello,
i am setting up a site to site vpn between two asa 5505's. the tunnel is up but i cannot get it to pass traffic and i have run out of ideas at this point. i am on site as i am posting this question and only have about 4 hours left to figure this out, so any help asap is greatly appreciated. i'll post the configs below along with the output of sh crypto isakmp sa and sh ipsec sa.
FYI the asa's are different versions, one is 9.2 the other is 8.2
Note: 1.1.1.1 = public ip for Site A 2.2.2.2 = public ip for site B
Site A running config:
Result of the command: "sh run"
: Saved
ASA Version 8.2(2)
hostname csol-asa
enable password WI19w3dXj6ANP8c6 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.1.0 san_antonio_inside
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 1.1.1.1 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns server-group DefaultDNS
name-server 24.93.41.125
name-server 24.93.41.126
object-group network NETWORK_OBJ_192.168.2.0_24
access-list inside_access_out extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in_1 extended permit icmp any interface outside
access-list outside_access_in_1 extended permit tcp any interface outside eq pop3
access-list outside_access_in_1 extended permit tcp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 8100
access-list outside_access_in_1 extended permit udp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 1025
access-list outside_access_in_1 extended permit tcp any interface outside eq 5020
access-list outside_access_in_1 extended permit tcp any interface outside eq 8080
access-list outside_access_in_1 extended permit tcp any interface outside eq www
access-list outside_access_in_1 extended permit ip san_antonio_inside 255.255.255.0 any
access-list outside_1_cryptomap extended permit ip 192.168.2.0 255.255.255.0 host san_antonio_inside
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.2.0 255.255.255.0 san_antonio_inside 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (inside) 2 interface
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface pop3 192.168.2.249 pop3 netmask 255.255.255.255
static (inside,outside) tcp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 8100 192.168.2.161 8100 netmask 255.255.255.255
static (inside,outside) udp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
static (inside,outside) tcp interface 5020 192.168.2.8 5020 netmask 255.255.255.255
static (inside,outside) tcp interface 8080 192.168.2.251 8080 netmask 255.255.255.255
static (inside,inside) tcp interface www 192.168.2.8 www netmask 255.255.255.255
static (inside,outside) tcp interface 1025 192.168.2.161 1025 netmask 255.255.255.255
access-group inside_access_out out interface inside
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 1.1.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.2.0 255.255.255.0 inside
http 2.2.2.2 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map1 1 match address outside_1_cryptomap_1
crypto map outside_map1 1 set peer 2.2.2.2
crypto map outside_map1 1 set transform-set ESP-3DES-SHA
crypto map outside_map1 interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.30-192.168.2.155 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain corporatesolutionsfw.local interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
tunnel-group 2.2.2.2 type ipsec-l2l
tunnel-group 2.2.2.2 ipsec-attributes
pre-shared-key *****
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:021cf43a4211a99232849372c380dda2
: end
Site A sh crypto isakmp sa:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 2.2.2.2
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
Site A sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map1, seq num: 1, local addr: 1.1.1.1
access-list outside_1_cryptomap_1 extended permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (san_antonio_inside/255.255.255.0/0/0)
current_peer: 2.2.2.2
#pkts encaps: 1, #pkts encrypt: 1, #pkts digest: 1
#pkts decaps: 239, #pkts decrypt: 239, #pkts verify: 239
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 1, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 1.1.1.1, remote crypto endpt.: 71.40.110.179
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: C1074C40
current inbound spi : B21273A9
inbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914989/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, }
slot: 0, conn_id: 1691648, crypto-map: outside_map1
sa timing: remaining key lifetime (kB/sec): (3914999/27694)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
Site B running config:
Result of the command: "sh run"
: Saved
: Serial Number: JMX184640WY
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)4
hostname CSOLSAASA
enable password WI19w3dXj6ANP8c6 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 2.2.2.2 255.255.255.248
ftp mode passive
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network mcallen_network
subnet 192.168.2.0 255.255.255.0
access-list outside_cryptomap extended permit ip object NETWORK_OBJ_192.168.1.0_24 object mcallen_network
access-list outside_access_in extended permit ip object mcallen_network 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-731-101.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static mcallen_network mcallen_network no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 2.2.2.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto map outside_map3 1 match address outside_cryptomap
crypto map outside_map3 1 set peer 1.1.1.1
crypto map outside_map3 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map3 interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh stricthostkeycheck
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd address 192.168.1.200-192.168.1.250 inside
dhcpd dns 24.93.41.125 24.93.41.126 interface inside
dhcpd domain CSOLSA.LOCAL interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
anyconnect-essentials
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
ikev1 pre-shared-key *****
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4e058021a6e84ac7956dca0e5a143b8d
: end
Site B sh crypto isakmp sa:
Result of the command: "sh crypto isakmp sa"
IKEv1 SAs:
Active SA: 1
Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1 IKE Peer: 1.1.1.1
Type : L2L Role : initiator
Rekey : no State : MM_ACTIVE
There are no IKEv2 SAs
Site B sh ipsec sa:
Result of the command: "sh ipsec sa"
interface: outside
Crypto map tag: outside_map3, seq num: 1, local addr: 71.40.110.179
access-list outside_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
local ident (addr/mask/prot/port): (192.168.1.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (192.168.2.0/255.255.255.0/0/0)
current_peer: 1.1.1.1
#pkts encaps: 286, #pkts encrypt: 286, #pkts digest: 286
#pkts decaps: 1, #pkts decrypt: 1, #pkts verify: 1
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 286, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: 2.2.2.2/0, remote crypto endpt.: 1.1.1.1/0
path mtu 1500, ipsec overhead 58(36), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: B21273A9
current inbound spi : C1074C40
inbound esp sas:
spi: 0xC1074C40 (3238480960)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373999/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000003
outbound esp sas:
spi: 0xB21273A9 (2987553705)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 28672, crypto-map: outside_map3
sa timing: remaining key lifetime (kB/sec): (4373987/27456)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001Hi Keegan,
Your tunnel is up and encrypting traffic one way, the other end is not able to encrypt the traffic.
I would suggest to do a 'clear xlate'? Sometimes if you setup the nonat configuration after you've attempted other configurations, you need to 'clear xlate' before the previous NAT configuration is cleared and the new one works.
HTH
"Please rate useful posts" -
Hi all,
I need some help from someone who has experience with configuring VPN on ASA over 2Wire router setup as dmzplus.
Topology:
ASA 5505 ---- 2Wire (dmzplus) -------------- ( cloud ) -------------- 2Wire (dmzplus) ---- ASA 5505
BT is the ISP on both ends. Static IPs are currently forwarded to the firewalls on both ends (outside interface is DHCP client).
All other services are working as expected (static NAT for few ports and so on).
I have found on some other forums the solution is to setup router in full bridge mode and then configure PPPoE on ASA, but I am trying to avoid this (for few other reasons).
The weird thing is when I am trying to initiate tunnel traffic from site A I can see IKE peer responder from site B, but not the opposite.
IKE state is MM_WAIT_MSG2 so it’s not passing the phase one. What I also notice in the arp table despite only one IP is assigned per site, the BT router has IP one less than the public one.
So my questions are:
1. Do I missing something in the config?
2. Is it possible to setup VPN on ASA over dmzplus?
3. Does the BT PPPoA service will become PPPoE after changing 2Wire to bridge mode?
4. Is there any different workaround or alternative solution?
CONFIG (crypto policies and all different settings are mirrored on the other end so it doesn’t make sense to post both):
: Saved
ASA Version 8.2(5)
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
access-list outside_in extended permit object-group PRS_PORTS any host 1.1.1.10
access-list outside_in extended permit object-group CCTV_PORTS any host 1.1.1.10
access-list VPN_traffic extended permit ip 192.168.0.0 255.255.255.0 192.168.1.0 255.255.255.0
access-list no-nat extended permit ip 192.168.0.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list no-nat
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
static (inside,outside) tcp interface <omitted>
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 1.1.1.9 1 (points
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication enable console LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set L2LVPN esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map L2LCRYPTO 10 match address VPN_traffic
crypto map L2LCRYPTO 10 set peer 2.2.2.10
crypto map L2LCRYPTO 10 set transform-set L2LVPN
crypto map L2LCRYPTO interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ciscoasa
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 569bb150
<omitted>
quit
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh <omitted>
ssh timeout 15
console timeout 0
management-access inside
dhcpd dns 194.72.0.98 194.74.65.68
dhcpd auto_config outside
dhcpd address 192.168.0.2-192.168.0.33 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 84.45.87.84 source outside prefer
webvpn
tunnel-group <2.2.2.10> type ipsec-l2l
tunnel-group <2.2.2.10> ipsec-attributes
pre-shared-key *****
isakmp keepalive threshold 100 retry 2
ISAKMP debug:
Feb 19 03:25:25 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:8021bed6 terminating: flags 0x01000022, refcnt 0, tuncnt 0
Feb 19 03:25:25 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:25:28 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:33 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:33 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:33 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:33 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:36 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:44 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:44 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:44 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 128
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, IKE MM Responder FSM error history (struct &0xc6dc3588) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent-->MM_SND_MSG2, EV_SND_MSG-->MM_SND_MSG2, EV_START_TMR-->MM_SND_MSG2, EV_RESEND_MSG-->MM_WAIT_MSG3, EV_TIMEOUT-->MM_WAIT_MSG3, NullEvent
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:a22d74b8 terminating: flags 0x01000002, refcnt 0, tuncnt 0
Feb 19 03:25:52 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:25:54 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, IKE Initiator: New Phase 1, Intf inside, IKE Peer <dest_ip> local Proxy Address 192.168.0.0, remote Proxy Address 192.168.1.0, Crypto map (L2LCRYPTO)
Feb 19 03:25:54 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing ISAKMP SA payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 02 payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 03 payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver RFC payload
Feb 19 03:25:54 [IKEv1 DEBUG]: IP = <dest_ip>, constructing Fragmentation VID + extended capabilities payload
Feb 19 03:25:54 [IKEv1]: IP = <dest_ip>, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:25:57 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:25:57 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:02 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:07 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:07 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:10 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:17 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:17 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:18 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, IKE MM Initiator FSM error history (struct &0xc6aa7940) <state>, <event>: MM_DONE, EV_ERROR-->MM_WAIT_MSG2, EV_RETRY-->MM_WAIT_MSG2, EV_TIMEOUT-->MM_WAIT_MSG2, NullEvent-->MM_SND_MSG1, EV_SND_MSG-->MM_SND_MSG1, EV_START_TMR-->MM_SND_MSG1, EV_RESEND_MSG-->MM_WAIT_MSG2, EV_RETRY
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, IKE SA MM:2e549563 terminating: flags 0x01000022, refcnt 0, tuncnt 0
Feb 19 03:26:26 [IKEv1 DEBUG]: IP = <dest_ip>, sending delete/delete with reason message
Feb 19 03:26:32 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, IKE Initiator: New Phase 1, Intf inside, IKE Peer <dest_ip> local Proxy Address 192.168.0.0, remote Proxy Address 192.168.1.0, Crypto map (L2LCRYPTO)
Feb 19 03:26:32 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing ISAKMP SA payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 02 payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver 03 payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing NAT-Traversal VID ver RFC payload
Feb 19 03:26:32 [IKEv1 DEBUG]: IP = <dest_ip>, constructing Fragmentation VID + extended capabilities payload
Feb 19 03:26:32 [IKEv1]: IP = <dest_ip>, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:40 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 168
Feb 19 03:26:43 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:43 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:43 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:43 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
no debug crypto isakmp 127 Feb 19 03:26:48 [IKEv1]: IP = <dest_ip>, IKE_DECODE RESENDING Message (msgid=0) with payloads : HDR + SA (1) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NONE (0) totano debug crypto isakmp 127 Feb 19 03:26:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:53 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Feb 19 03:26:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
Feb 19 03:26:53 [IKEv1]: IP = <dest_ip>, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.
Kind regards
MariuszHi all,
The latest update
I've finally managed to get the VPN to work! As soon as I've reconfigure the router and the firewall it took 1 second to establish the tunnel. So the answer for the most important question number 2. Is it possible to setup VPN on ASA over dmzplus? is no. I think the issue is related to routing which doesn't look normal with the dmzplus (can't properly traceroute to IPs etc)
So my solution was :
- changed 2Wire settings (Bridged LLC, ATM PVC disabled, Connection type: direct IP, save and uncheck Routing mode)
- changed ASA external interface settings to pppoe with automatic routing and IP
Regards
Mariusz -
IKEv2 Doesn't support Multiple Peers action to take
Hi,
I have to establish a tunnel from the local FW to a remote FW in L2L
In case of failure of the remote FW, a tunnel has to be opened with the backup remote FW.
I have proposed to use IKEv2
But with following config i get the message: %ASA-4-752009: IKEv2 Doesn't support Multiple Peers
crypto map local-map 30 set peer 22.22.22.22 33.33.33.33
So i have created two crypto maps:
crypto map local-map 30 set peer 22.22.22.22
crypto map local-map 40 set peer 33.33.33.33
The primary tunnel with peer 22.22.22.22 works fine but with the backup tunnel with peer 33.33.33.33
The tunnel IPSEc is up but no interesting traffic enters the tunnel:
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 28, #pkts decrypt: 28, #pkts verify: 28
I have first taken a capture on the inside interface and i see the counter of the access-list incrementing
but when i take a capture on the outside interface, i don't see any interesting traffic.
I have tried the clear crypto command but no way.
Equipment: Cluster of Cisco ASA 5510 at rel 8.4.7
Do i have to reboot the FW or may be the two crypto maps that i have created are not the good solution.
As an alternative if i want to maintain both peers on the same line i can replace IKEv2 by IKEv1.
Best regards.
AndreHello Andre, this is a confirmed issue with Cisco. There is an official bug listed as "ENH: Multiple Peers support for IKEv2 CSCud22276" (Cisco customer login required to view bug). See also the Cisco TAC Document "Migration of IKEv1 to IKEv2 L2L Tunnel" with the following quote:
"Multiple peers used for redundancy is not supported with IKEv2 on the ASA. In IKEv1, for redundancy purposes, one can have more than one peer under the same crypto map when you enter the set peer command. The first peer will be the primary and if it fails, the second peer will kick in. Refer to Cisco bug ID CSCud22276 (registered customers only) , ENH: Multiple Peers support for IKEv2."
Here's an excerpt from the Bug Enhancement Request regarding how to work around the issue.
"Either:
1) remove all but one peer from the crypto map
or
2) use IKEv1 instead of IKEv2"
Hopefully this helps, it would be a great feature for Cisco to add for better migration from IKEv1. I guess a more complicated alternative might be to use BGP and multiple WAN connections to have more than one valid path for the same WAN IP of your IPSec IKEv2 peer. -
Confused with this ASA - VPN config issue
Hello. Can anyone help me here? I am new to the ASA config and commands. Everything works well, enough, on this ASA except the VPN. A client can connect but cannot access anything inside or outside. Here is the config. Can someone please take a look and tell me why VPN is not working? I don't want to set up split-tunneling, I would prefer everything to go through the firewall. Also, if you see something else wrong (or have a better implementation) then please let me know.
ASA Version 8.4(2)
hostname FIREWALL_NAME
enable password Some_X's_here encrypted
passwd Some_X's_here encrypted
names
interface Ethernet0/0
speed 100
duplex full
no nameif
no security-level
no ip address
interface Ethernet0/0.22
description Public Internet space via VLAN 22
vlan 22
nameif Public_Internet
security-level 0
ip address 1.3.3.7 255.255.255.248
interface Ethernet0/1
speed 100
duplex full
no nameif
no security-level
no ip address
interface Ethernet0/1.42
description Private LAN space via VLAN 42
shutdown
vlan 42
nameif Private_CDATA
security-level 100
ip address 10.30.136.1 255.255.255.0
interface Ethernet0/1.69
description Private LAN space via VLAN 69
vlan 69
nameif Private_ODATA
security-level 100
ip address 10.30.133.1 255.255.255.0
interface Ethernet0/1.95
description Private LAN space via VLAN 95
shutdown
vlan 95
nameif Private_OVOICE
security-level 100
ip address 192.168.102.254 255.255.255.0
interface Ethernet0/1.96
description Private LAN space via VLAN 96
shutdown
vlan 96
nameif Private_CVOICE
security-level 100
ip address 192.168.91.254 255.255.255.0
interface Ethernet0/1.3610
description Private LAN subnet via VLAN 3610
shutdown
vlan 3610
nameif Private_CeDATA
security-level 100
ip address 10.10.100.18 255.255.255.240
interface Ethernet0/1.3611
description Private LAN space via VLAN 3611
shutdown
vlan 3611
nameif Private_CeVOICE
security-level 100
ip address 10.10.100.66 255.255.255.252
interface Ethernet0/2
shutdown
no nameif
security-level 0
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.69.1 255.255.255.0
management-only
banner exec WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest
extent of the law.
banner exec
banner exec ,
banner exec .';
banner exec .-'` .'
banner exec ,`.-'-.`\
banner exec ; / '-'
banner exec | \ ,-,
banner exec \ '-.__ )_`'._ \|/
banner exec '. ``` ``'--._[]--------------*
banner exec .-' , `'-. /|\
banner exec '-'`-._ (( o )
banner exec `'--....(`- ,__..--'
banner exec '-'`
banner exec
banner exec frickin' sharks with frickin' laser beams attached to their frickin' heads
banner login WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest
extent of the law.
banner asdm WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest
extent of the law.
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network CD_3610-GW
host 10.10.100.17
description First hop to 3610
object network CV_3611-GW
host 10.10.100.65
description First hop to 3611
object network GW_22-EXT
host 1.3.3.6
description First hop to 22
object service MS-RDC
service tcp source range 1024 65535 destination eq 3389
description Microsoft Remote Desktop Connection
object network HDC-LAN
subnet 192.168.200.0 255.255.255.0
description DC LAN subnet
object network HAM-LAN
subnet 192.168.110.0 255.255.255.0
description HAM LAN subnet
object service MSN
service tcp source range 1 65535 destination eq 1863
description MSN Messenger
object network BCCs
host 2.1.8.1
description BCCs server access
object network ODLW-EXT
host 7.1.1.5
description OTTDl
object network SWINDS-INT
host 10.30.133.67
description SWINDS server
object network SWINDS(192.x.x.x)-INT
host 192.168.100.67
description SWINDS server
object service YMSG
service tcp source range 1 65535 destination eq 5050
description Yahoo Messenger
object service c.b.ca1
service tcp source range 1 65535 destination eq citrix-ica
description Connections to the bc portal.
object service c.b.ca2
service tcp source range 1 65535 destination eq 2598
description Connections to the bc portal.
object service HTTP-EXT(7001)
service tcp source range 1 65535 destination eq 7001
description HTTP Extended on port 7001.
object service HTTP-EXT(8000-8001)
service tcp source range 1 65535 destination range 8000 8001
description HTTP Extended on ports 8000-8001.
object service HTTP-EXT(8080-8081)
service tcp source range 1 65535 destination range 8080 8081
description HTTP Extended on ports 8080-8081.
object service HTTP-EXT(8100)
service tcp source range 1 65535 destination eq 8100
description HTTP Extended on port 8100.
object service HTTP-EXT(8200)
service tcp source range 1 65535 destination eq 8200
description HTTP Extended on port 8200.
object service HTTP-EXT(8888)
service tcp source range 1 65535 destination eq 8888
description HTTP Extended on port 8888.
object service HTTP-EXT(9080)
service tcp source range 1 65535 destination eq 9080
description HTTP Extended on port 9080.
object service ntp
service tcp source range 1 65535 destination eq 123
description TCP NTP on port 123.
object network Pl-EXT
host 7.1.1.2
description OPl box.
object service Pl-Admin
service tcp source range 1 65535 destination eq 8443
description Pl Admin portal
object network FW-EXT
host 1.3.3.7
description External/Public interface IP address of firewall.
object network Rs-EXT
host 7.1.1.8
description Rs web portal External/Public IP.
object network DWDM-EXT
host 2.1.2.1
description DWDM.
object network HM_VPN-EXT
host 6.2.9.7
description HAM Man.
object network SIM_MGMT
host 2.1.1.1
description SIM Man.
object network TS_MGMT
host 2.1.1.4
description TS Man.
object network TS_MGMT
host 2.1.2.2
description TS Man.
object service VPN-TCP(1723)
service tcp source range 1 65535 destination eq pptp
description For PPTP control path.
object service VPN-UDP(4500)
service udp source range 1 65535 destination eq 4500
description For L2TP(IKEv1) and IKEv2.
object service VPN-TCP(443)
service tcp source range 1 65535 destination eq https
description For SSTP control and data path.
object service VPN-UDP(500)
service udp source range 1 65535 destination eq isakmp
description For L2TP(IKEv1) and IKEv2.
object network RCM
host 6.1.8.2
description RCM
object network RCM_Y
host 6.1.8.9
description RCM Y
object network r.r.r.c163
host 2.1.2.63
description RCV IP.
object network r.r.r.c227
host 2.1.2.27
description RCV IP.
object network v.t.c-EXT
host 2.5.1.2
description RTICR
object service VPN-TCP(10000)
service tcp source range 1 65535 destination eq 10000
description For TCP VPN over port 1000.
object service BGP-JY
service tcp source range 1 65535 destination eq 21174
description BPG
object network KooL
host 192.168.100.100
description KooL
object network FW_Test
host 1.3.3.7
description Testing other External IP
object network AO_10-30-133-0-LAN
range 10.30.133.0 10.30.133.229
description OLS 10.30.133.0/24
object network AC_10-30-136-0-LAN
subnet 10.30.136.0 255.255.255.0
description CLS 10.30.136.0/24
object network NETWORK_OBJ_192.168.238.0_27
subnet 192.168.238.0 255.255.255.224
object-group network All_Private_Interfaces
description All private interfaces
network-object 10.30.133.0 255.255.255.0
network-object 10.30.136.0 255.255.255.0
network-object 10.10.100.16 255.255.255.240
network-object 10.10.100.64 255.255.255.252
network-object 192.168.102.0 255.255.255.0
network-object 192.168.91.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service cb.ca
description All ports required for cb.ca connections.
service-object object c.b.ca1
service-object object c.b.ca2
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq https
service-object udp destination eq snmp
object-group service FTP
description All FTP ports (20 + 21)
service-object tcp destination eq ftp
service-object tcp destination eq ftp-data
object-group service HTTP-EXT
description HTTP Extended port ranges.
service-object object HTTP-EXT(7001)
service-object object HTTP-EXT(8000-8001)
service-object object HTTP-EXT(8080-8081)
service-object object HTTP-EXT(8100)
service-object object HTTP-EXT(8200)
service-object object HTTP-EXT(8888)
service-object object HTTP-EXT(9080)
object-group service ICMP_Any
description ICMP: Any Type, Any Code
service-object icmp alternate-address
service-object icmp conversion-error
service-object icmp echo
service-object icmp echo-reply
service-object icmp information-reply
service-object icmp information-request
service-object icmp mask-reply
service-object icmp mask-request
service-object icmp mobile-redirect
service-object icmp parameter-problem
service-object icmp redirect
service-object icmp router-advertisement
service-object icmp router-solicitation
service-object icmp source-quench
service-object icmp time-exceeded
service-object icmp timestamp-reply
service-object icmp timestamp-request
service-object icmp traceroute
service-object icmp unreachable
service-object icmp6 echo
service-object icmp6 echo-reply
service-object icmp6 membership-query
service-object icmp6 membership-reduction
service-object icmp6 membership-report
service-object icmp6 neighbor-advertisement
service-object icmp6 neighbor-redirect
service-object icmp6 neighbor-solicitation
service-object icmp6 packet-too-big
service-object icmp6 parameter-problem
service-object icmp6 router-advertisement
service-object icmp6 router-renumbering
service-object icmp6 router-solicitation
service-object icmp6 time-exceeded
service-object icmp6 unreachable
service-object icmp
object-group service NTP
description TCP and UPD NTP protocol
service-object object ntp
service-object udp destination eq ntp
object-group service DM_INLINE_SERVICE_3
group-object FTP
group-object HTTP-EXT
group-object ICMP_Any
group-object NTP
service-object tcp-udp destination eq domain
service-object tcp-udp destination eq www
service-object tcp destination eq https
service-object tcp destination eq ssh
service-object ip
object-group service DM_INLINE_SERVICE_4
group-object NTP
service-object tcp destination eq daytime
object-group network SWINDS
description Both Internal IP addresses (192 + 10)
network-object object SWINDS-INT
network-object object SWINDS(192.x.x.x)-INT
object-group service IM_Types
description All messenger type applications
service-object object MSN
service-object object YMSG
service-object tcp-udp destination eq talk
service-object tcp destination eq aol
service-object tcp destination eq irc
object-group service SNMP
description Both poll and trap ports.
service-object udp destination eq snmp
service-object udp destination eq snmptrap
object-group service DM_INLINE_SERVICE_2
group-object FTP
service-object object MS-RDC
service-object object Pl-Admin
group-object SNMP
object-group network DM_INLINE_NETWORK_1
network-object object FW-EXT
network-object object Rs-EXT
object-group network AMV
description connections for legacy AM
network-object object DWDM-EXT
network-object object HAM_MGMT
network-object object SIM_MGMT
network-object object TS_MGMT
network-object object TS_MGMT
object-group service IKEv2_L2TP
description IKEv2 and L2TP VPN configurations
service-object esp
service-object object VPN-UDP(4500)
service-object object VPN-UDP(500)
object-group service PPTP
description PPTP VPN configuration
service-object gre
service-object object VPN-TCP(1723)
object-group service SSTP
description SSTP VPN configuration
service-object object VPN-TCP(443)
object-group network RvIPs
description Rv IP addresses
network-object object RCM
network-object object RCM_Y
network-object object r.r.r.c163
network-object object r.r.r.c227
network-object object v.t.c-EXT
object-group service Rvs
description Rv configuration.
service-object object VPN-TCP(10000)
service-object object VPN-UDP(500)
object-group service DM_INLINE_SERVICE_5
service-object object BGP-JY
service-object tcp destination eq bgp
object-group network Local_Private_Subnets
description OandCl DATA
network-object 10.30.133.0 255.255.255.0
network-object 10.30.136.0 255.255.255.0
access-list Public/Internet_access_out remark Block all IM traffic out.
access-list Public/Internet_access_out extended deny object-group IM_Types object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Access from SWINDS to DLM portal
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_1 object-group SWINDS object ODLW-EXT
access-list Public/Internet_access_out remark Allow access to BMC portal
access-list Public/Internet_access_out extended permit object-group cb.ca object-group Local_Private_Subnets object BCCs
access-list Public/Internet_access_out remark Allow basic services out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_3 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow WhoIS traffic out.
access-list Public/Internet_access_out extended permit tcp object-group Local_Private_Subnets any eq whois
access-list Public/Internet_access_out remark Allow Network Time protocols out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_4 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow all IP based monitoring traffic to Pl.
access-list Public/Internet_access_out extended permit ip object-group SWINDS object Pl-EXT
access-list Public/Internet_access_out remark Allow Management traffic to Pl-JY.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_2 object-group Local_Private_Subnets object Pl-EXT
access-list Public/Internet_access_out remark Allow FTP traffic to Grimlock and RS FTP.
access-list Public/Internet_access_out extended permit object-group FTP object-group Local_Private_Subnets object-group DM_INLINE_NETWORK_1
access-list Public/Internet_access_out remark Allow VPN traffic to AM-JY.
access-list Public/Internet_access_out extended permit object-group IKEv2_L2TP object-group Local_Private_Subnets object-group AMV
access-list Public/Internet_access_out remark Allow VPN traffic to RCm devices.
access-list Public/Internet_access_out extended permit object-group Rvs object-group Local_Private_Subnets object-group RvIPs
access-list Public/Internet_access_out remark Allow BPG traffic out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_5 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow Kool server out.
access-list Public/Internet_access_out extended permit ip object KooL any
pager lines 24
logging enable
logging history informational
logging asdm informational
logging mail notifications
logging from-address [email protected]
logging recipient-address [email protected] level errors
mtu Public_Internet 1500
mtu Private_CDATA 1500
mtu Private_ODATA 1500
mtu Private_OVOICE 1500
mtu Private_CVOICE 1500
mtu Private_CeDATA 1500
mtu Private_CeVOICE 1500
mtu management 1500
ip local pool AO-VPN_Pool 192.168.238.2-192.168.238.30 mask 255.255.255.224
ip verify reverse-path interface Public_Internet
ip verify reverse-path interface Private_CDATA
ip verify reverse-path interface Private_ODATA
ip verify reverse-path interface Private_OVOICE
ip verify reverse-path interface Private_CVOICE
ip verify reverse-path interface Private_CeDATA
ip verify reverse-path interface Private_CeVOICE
ip verify reverse-path interface management
icmp unreachable rate-limit 1 burst-size 1
icmp deny any Public_Internet
no asdm history enable
arp timeout 14400
nat (Private_ODATA,Public_Internet) source dynamic AO_10-30-133-0-LAN interface
nat (Private_CDATA,Public_Internet) source dynamic AC_10-30-136-0-LAN interface
nat (Private_ODATA,Public_Internet) source static any any destination static NETWORK_OBJ_192.168.238.0_27 NETWORK_OBJ_192.168.238.0_27 no-proxy-arp route-lookup
access-group Public/Internet_access_out out interface Public_Internet
route Public_Internet 0.0.0.0 0.0.0.0 1.3.3.6 1
route Private_CeDATA 10.0.0.0 255.0.0.0 10.10.100.17 1
route Private_CeDATA 10.1.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.3.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.5.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.11.106.74 255.255.255.255 10.10.100.17 1
route Private_CeDATA 10.30.128.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.130.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.131.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.132.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.134.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.135.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.67.31.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.224.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 4.1.1.19 255.255.255.255 10.10.100.17 1
route Private_CeDATA 1.1.1.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 1.1.1.13 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.11.24 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.11.27 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.17.105 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.64 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.66 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.110 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.251.57 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.21.56.105 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.21.57.152 255.255.255.255 10.10.100.17 1
route Private_CeDATA 192.168.3.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.9.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.20.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.21.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.30.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.31.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.40.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.41.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.50.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.60.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.61.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.70.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.101.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.110.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.200.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.251.177.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 2.1.2.7 255.255.255.255 10.10.100.17 1
route Private_CeDATA 2.1.2.74 255.255.255.255 10.10.100.17 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (Private_ODATA) host 10.30.133.21
timeout 5
nt-auth-domain-controller Cool_Transformer_Name
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
aaa authentication serial console LOCAL
http server enable
http 192.168.69.0 255.255.255.0 management
snmp-server host Private_ODATA 10.30.133.67 poll community Some_*s_here version 2c
snmp-server location OT
snmp-server contact [email protected]
snmp-server community Some_*s_here
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
snmp-server enable traps syslog
snmp-server enable traps ipsec start stop
snmp-server enable traps entity config-change fru-insert fru-remove
snmp-server enable traps memory-threshold
snmp-server enable traps interface-threshold
snmp-server enable traps remote-access session-threshold-exceeded
snmp-server enable traps connection-limit-reached
snmp-server enable traps cpu threshold rising
snmp-server enable traps ikev2 start stop
snmp-server enable traps nat packet-discard
sysopt noproxyarp Public_Internet
sysopt noproxyarp Private_CDATA
sysopt noproxyarp Private_ODATA
sysopt noproxyarp Private_OVOICE
sysopt noproxyarp Private_CVOICE
sysopt noproxyarp Private_CeDATA
sysopt noproxyarp Private_CeVOICE
sysopt noproxyarp management
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Public_Internet_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Public_Internet_map interface Public_Internet
crypto ikev1 enable Public_Internet
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
client-update enable
telnet timeout 5
ssh 10.30.133.0 255.255.255.0 Private_ODATA
ssh 192.168.69.0 255.255.255.0 management
ssh timeout 2
ssh version 2
console timeout 5
dhcprelay server 10.30.133.13 Private_ODATA
dhcprelay enable Private_CDATA
dhcprelay timeout 60
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 10.30.133.13 prefer
ntp server 132.246.11.227
ntp server 10.30.133.21
webvpn
group-policy AO-VPN_Tunnel internal
group-policy AO-VPN_Tunnel attributes
dns-server value 10.30.133.21 10.30.133.13
vpn-tunnel-protocol ikev1
default-domain value ao.local
username helpme password Some_X's_here encrypted privilege 1
username helpme attributes
service-type nas-prompt
tunnel-group AO-VPN_Tunnel type remote-access
tunnel-group AO-VPN_Tunnel general-attributes
address-pool AO-VPN_Pool
authentication-server-group AD
default-group-policy AO-VPN_Tunnel
tunnel-group AO-VPN_Tunnel ipsec-attributes
ikev1 pre-shared-key Some_*s_here
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class class-default
user-statistics accounting
service-policy global_policy global
smtp-server 192.168.200.25
prompt hostname context
no call-home reporting anonymous
Thanks,
Jeff.I tried those commands but this started getting messy and so I looked at the current config and it was not the same as what I originally posted. Looks like some changes were implemented but not saved so the config that I posted what slightly different. Thank you for all your suggestions. Here is the new config, confirmed as the current running and saved config. Same situation as before though. I can connect using the Cisco VPN client but can only ping myself and can't get out to the Internet or access anything internal. If someone can take a look it would be greatly appreciated. The main difference is the VPN pool has been set as a subset of the 10.30.133.0 network instead of using a separate subnet (VPN pool is 10.30.133.200 - 10.30.133.230).
ASA Version 8.4(2)
hostname FIREWALL_NAME
enable password Some_X's_here encrypted
passwd Some_X's_here encrypted
names
interface Ethernet0/0
speed 100
duplex full
no nameif
no security-level
no ip address
interface Ethernet0/0.22
description Public Internet space via VLAN 22
vlan 22
nameif Public_Internet
security-level 0
ip address 1.3.3.7 255.255.255.248
interface Ethernet0/1
speed 100
duplex full
no nameif
no security-level
no ip address
interface Ethernet0/1.42
description Private LAN space via VLAN 42
shutdown
vlan 42
nameif Private_CDATA
security-level 100
ip address 10.30.136.1 255.255.255.0
interface Ethernet0/1.69
description Private LAN space via VLAN 69
vlan 69
nameif Private_ODATA
security-level 100
ip address 10.30.133.1 255.255.255.0
interface Ethernet0/1.95
description Private LAN space via VLAN 95
shutdown
vlan 95
nameif Private_OVOICE
security-level 100
ip address 192.168.102.254 255.255.255.0
interface Ethernet0/1.96
description Private LAN space via VLAN 96
shutdown
vlan 96
nameif Private_CVOICE
security-level 100
ip address 192.168.91.254 255.255.255.0
interface Ethernet0/1.3610
description Private LAN subnet via VLAN 3610
shutdown
vlan 3610
nameif Private_CeDATA
security-level 100
ip address 10.10.100.18 255.255.255.240
interface Ethernet0/1.3611
description Private LAN space via VLAN 3611
shutdown
vlan 3611
nameif Private_CeVOICE
security-level 100
ip address 10.10.100.66 255.255.255.252
interface Ethernet0/2
shutdown
no nameif
security-level 0
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.69.1 255.255.255.0
management-only
banner exec WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest extent of the law.
banner exec
banner exec ,
banner exec .';
banner exec .-'` .'
banner exec ,`.-'-.`\
banner exec ; / '-'
banner exec | \ ,-,
banner exec \ '-.__ )_`'._ \|/
banner exec '. ``` ``'--._[]--------------*
banner exec .-' , `'-. /|\
banner exec '-'`-._ (( o )
banner exec `'--....(`- ,__..--'
banner exec '-'`
banner exec
banner exec frickin' sharks with frickin' laser beams attached to their frickin' heads
banner login WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest extent of the law.
banner asdm WARNING!! Access to this device is restricted to those individuals with specific permissions. If you are not an authorized user, disconnect now. Any attempts to gain unauthorized access will be prosecuted to the fullest extent of the law.
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network CD_3610-GW
host 10.10.100.17
description First hop to 3610
object network CV_3611-GW
host 10.10.100.65
description First hop to 3611
object network GW_22-EXT
host 1.3.3.6
description First hop to 22
object network Ts-LAN
host 192.168.100.4
description TS
object service MS-RDC
service tcp source range 1024 65535 destination eq 3389
description Microsoft Remote Desktop Connection
object network HDC-LAN
subnet 192.168.200.0 255.255.255.0
description DC LAN subnet
object network HAM-LAN
subnet 192.168.110.0 255.255.255.0
description HAM LAN subnet
object service MSN
service tcp source range 1 65535 destination eq 1863
description MSN Messenger
object network BCCs
host 2.1.8.1
description BCCs server access
object network ODLW-EXT
host 7.1.1.5
description OTTDl
object network SWINDS-INT
host 10.30.133.67
description SWINDS server
object network SWINDS(192.x.x.x)-INT
host 192.168.100.67
description SWINDS server
object service YMSG
service tcp source range 1 65535 destination eq 5050
description Yahoo Messenger
object service c.b.ca1
service tcp source range 1 65535 destination eq citrix-ica
description Connections to the bc portal.
object service c.b.ca2
service tcp source range 1 65535 destination eq 2598
description Connections to the bc portal.
object service HTTP-EXT(7001)
service tcp source range 1 65535 destination eq 7001
description HTTP Extended on port 7001.
object service HTTP-EXT(8000-8001)
service tcp source range 1 65535 destination range 8000 8001
description HTTP Extended on ports 8000-8001.
object service HTTP-EXT(8080-8081)
service tcp source range 1 65535 destination range 8080 8081
description HTTP Extended on ports 8080-8081.
object service HTTP-EXT(8100)
service tcp source range 1 65535 destination eq 8100
description HTTP Extended on port 8100.
object service HTTP-EXT(8200)
service tcp source range 1 65535 destination eq 8200
description HTTP Extended on port 8200.
object service HTTP-EXT(8888)
service tcp source range 1 65535 destination eq 8888
description HTTP Extended on port 8888.
object service HTTP-EXT(9080)
service tcp source range 1 65535 destination eq 9080
description HTTP Extended on port 9080.
object service ntp
service tcp source range 1 65535 destination eq 123
description TCP NTP on port 123.
object network Pl-EXT
host 7.1.1.2
description OPl box.
object service Pl-Admin
service tcp source range 1 65535 destination eq 8443
description Pl Admin portal
object network FW-EXT
host 1.3.3.7
description External/Public interface IP address of firewall.
object network Rs-EXT
host 7.1.1.8
description Rs web portal External/Public IP.
object network DWDM-EXT
host 2.1.2.1
description DWDM.
object network HM_VPN-EXT
host 6.2.9.7
description HAM Man.
object network SIM_MGMT
host 2.1.1.1
description SIM Man.
object network TS_MGMT
host 2.1.1.4
description TS Man.
object network TS_MGMT
host 2.1.2.2
description TS Man.
object service VPN-TCP(1723)
service tcp source range 1 65535 destination eq pptp
description For PPTP control path.
object service VPN-UDP(4500)
service udp source range 1 65535 destination eq 4500
description For L2TP(IKEv1) and IKEv2.
object service VPN-TCP(443)
service tcp source range 1 65535 destination eq https
description For SSTP control and data path.
object service VPN-UDP(500)
service udp source range 1 65535 destination eq isakmp
description For L2TP(IKEv1) and IKEv2.
object network RCM
host 6.1.8.2
description RCM
object network RCM_Y
host 6.1.8.9
description RCM Y
object network r.r.r.c163
host 2.1.2.63
description RCV IP.
object network r.r.r.c227
host 2.1.2.27
description RCV IP.
object network v.t.c-EXT
host 2.5.1.2
description RTICR
object service VPN-TCP(10000)
service tcp source range 1 65535 destination eq 10000
description For TCP VPN over port 1000.
object service BGP-JY
service tcp source range 1 65535 destination eq 21174
description BPG
object network KooL
host 192.168.100.100
description KooL
object network FW_Test
host 1.3.3.7
description Testing other External IP
object network AO_10-30-133-0-LAN
subnet 10.30.133.0 255.255.255.0
description OLS 10.30.133.0/24
object network AC_10-30-136-0-LAN
subnet 10.30.136.0 255.255.255.0
description CLS 10.30.136.0/24
object-group network All_Private_Interfaces
description All private interfaces
network-object 10.30.133.0 255.255.255.0
network-object 10.30.136.0 255.255.255.0
network-object 10.10.100.16 255.255.255.240
network-object 10.10.100.64 255.255.255.252
network-object 192.168.102.0 255.255.255.0
network-object 192.168.91.0 255.255.255.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service cb.ca
description All ports required for cb.ca connections.
service-object object c.b.ca1
service-object object c.b.ca2
object-group service DM_INLINE_SERVICE_1
service-object tcp destination eq https
service-object udp destination eq snmp
object-group service FTP
description All FTP ports (20 + 21)
service-object tcp destination eq ftp
service-object tcp destination eq ftp-data
object-group service HTTP-EXT
description HTTP Extended port ranges.
service-object object HTTP-EXT(7001)
service-object object HTTP-EXT(8000-8001)
service-object object HTTP-EXT(8080-8081)
service-object object HTTP-EXT(8100)
service-object object HTTP-EXT(8200)
service-object object HTTP-EXT(8888)
service-object object HTTP-EXT(9080)
object-group service ICMP_Any
description ICMP: Any Type, Any Code
service-object icmp alternate-address
service-object icmp conversion-error
service-object icmp echo
service-object icmp echo-reply
service-object icmp information-reply
service-object icmp information-request
service-object icmp mask-reply
service-object icmp mask-request
service-object icmp mobile-redirect
service-object icmp parameter-problem
service-object icmp redirect
service-object icmp router-advertisement
service-object icmp router-solicitation
service-object icmp source-quench
service-object icmp time-exceeded
service-object icmp timestamp-reply
service-object icmp timestamp-request
service-object icmp traceroute
service-object icmp unreachable
service-object icmp6 echo
service-object icmp6 echo-reply
service-object icmp6 membership-query
service-object icmp6 membership-reduction
service-object icmp6 membership-report
service-object icmp6 neighbor-advertisement
service-object icmp6 neighbor-redirect
service-object icmp6 neighbor-solicitation
service-object icmp6 packet-too-big
service-object icmp6 parameter-problem
service-object icmp6 router-advertisement
service-object icmp6 router-renumbering
service-object icmp6 router-solicitation
service-object icmp6 time-exceeded
service-object icmp6 unreachable
service-object icmp
object-group service NTP
description TCP and UPD NTP protocol
service-object object ntp
service-object udp destination eq ntp
object-group service DM_INLINE_SERVICE_3
group-object FTP
group-object HTTP-EXT
group-object ICMP_Any
group-object NTP
service-object tcp-udp destination eq domain
service-object tcp-udp destination eq www
service-object tcp destination eq https
service-object tcp destination eq ssh
service-object ip
object-group service DM_INLINE_SERVICE_4
group-object NTP
service-object tcp destination eq daytime
object-group network SWINDS
description Both Internal IP addresses (192 + 10)
network-object object SWINDS-INT
network-object object SWINDS(192.x.x.x)-INT
object-group service IM_Types
description All messenger type applications
service-object object MSN
service-object object YMSG
service-object tcp-udp destination eq talk
service-object tcp destination eq aol
service-object tcp destination eq irc
object-group service SNMP
description Both poll and trap ports.
service-object udp destination eq snmp
service-object udp destination eq snmptrap
object-group service DM_INLINE_SERVICE_2
group-object FTP
service-object object MS-RDC
service-object object Pl-Admin
group-object SNMP
object-group network DM_INLINE_NETWORK_1
network-object object FW-EXT
network-object object Rs-EXT
object-group network AMV
description connections for legacy AM
network-object object DWDM-EXT
network-object object HAM_MGMT
network-object object SIM_MGMT
network-object object TS_MGMT
network-object object TS_MGMT
object-group service IKEv2_L2TP
description IKEv2 and L2TP VPN configurations
service-object esp
service-object object VPN-UDP(4500)
service-object object VPN-UDP(500)
object-group service PPTP
description PPTP VPN configuration
service-object gre
service-object object VPN-TCP(1723)
object-group service SSTP
description SSTP VPN configuration
service-object object VPN-TCP(443)
object-group network RvIPs
description Rv IP addresses
network-object object RCM
network-object object RCM_Y
network-object object r.r.r.c163
network-object object r.r.r.c227
network-object object v.t.c-EXT
object-group service Rvs
description Rv configuration.
service-object object VPN-TCP(10000)
service-object object VPN-UDP(500)
object-group service DM_INLINE_SERVICE_5
service-object object BGP-JY
service-object tcp destination eq bgp
object-group network Local_Private_Subnets
description OandCl DATA
network-object 10.30.133.0 255.255.255.0
network-object 10.30.136.0 255.255.255.0
object-group service IPSec
description IPSec traffic
service-object object VPN-UDP(4500)
service-object object VPN-UDP(500)
access-list Public/Internet_access_out remark Block all IM traffic out.
access-list Public/Internet_access_out extended deny object-group IM_Types object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Access from SWINDS to DLM portal
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_1 object-group SWINDS object ODLW-EXT
access-list Public/Internet_access_out remark Allow access to BMC portal
access-list Public/Internet_access_out extended permit object-group cb.ca object-group Local_Private_Subnets object BCCs
access-list Public/Internet_access_out remark Allow basic services out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_3 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow WhoIS traffic out.
access-list Public/Internet_access_out extended permit tcp object-group Local_Private_Subnets any eq whois
access-list Public/Internet_access_out remark Allow Network Time protocols out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_4 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow all IP based monitoring traffic to Pl.
access-list Public/Internet_access_out extended permit ip object-group SWINDS object Pl-EXT
access-list Public/Internet_access_out remark Allow Management traffic to Pl-JY.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_2 object-group Local_Private_Subnets object Pl-EXT
access-list Public/Internet_access_out remark Allow FTP traffic to Grimlock and RS FTP.
access-list Public/Internet_access_out extended permit object-group FTP object-group Local_Private_Subnets object-group DM_INLINE_NETWORK_1
access-list Public/Internet_access_out remark Allow VPN traffic to AM-JY.
access-list Public/Internet_access_out extended permit object-group IKEv2_L2TP object-group Local_Private_Subnets object-group AMV
access-list Public/Internet_access_out remark Allow VPN traffic to RCm devices.
access-list Public/Internet_access_out extended permit object-group Rvs object-group Local_Private_Subnets object-group RvIPs
access-list Public/Internet_access_out remark Allow BPG traffic out.
access-list Public/Internet_access_out extended permit object-group DM_INLINE_SERVICE_5 object-group Local_Private_Subnets any
access-list Public/Internet_access_out remark Allow Kool server out.
access-list Public/Internet_access_out extended permit ip object KooL any
pager lines 24
logging enable
logging history informational
logging asdm informational
logging mail notifications
logging from-address [email protected]
logging recipient-address [email protected] level errors
mtu Public_Internet 1500
mtu Private_CDATA 1500
mtu Private_ODATA 1500
mtu Private_OVOICE 1500
mtu Private_CVOICE 1500
mtu Private_CeDATA 1500
mtu Private_CeVOICE 1500
mtu management 1500
ip local pool AO-VPN_Pool 192.168.238.2-192.168.238.30 mask 255.255.255.224
ip verify reverse-path interface Public_Internet
ip verify reverse-path interface Private_CDATA
ip verify reverse-path interface Private_ODATA
ip verify reverse-path interface Private_OVOICE
ip verify reverse-path interface Private_CVOICE
ip verify reverse-path interface Private_CeDATA
ip verify reverse-path interface Private_CeVOICE
ip verify reverse-path interface management
icmp unreachable rate-limit 1 burst-size 1
icmp deny any Public_Internet
no asdm history enable
arp timeout 14400
nat (Private_ODATA,Public_Internet) source dynamic AO_10-30-133-0-LAN interface
nat (Private_CDATA,Public_Internet) source dynamic AC_10-30-136-0-LAN interface
nat (Private_ODATA,Public_Internet) source static any any destination static NETWORK_OBJ_192.168.238.0_27 NETWORK_OBJ_192.168.238.0_27 no-proxy-arp route-lookup
access-group Public/Internet_access_out out interface Public_Internet
route Public_Internet 0.0.0.0 0.0.0.0 1.3.3.6 1
route Private_CeDATA 10.0.0.0 255.0.0.0 10.10.100.17 1
route Private_CeDATA 10.1.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.3.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.5.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 10.11.106.74 255.255.255.255 10.10.100.17 1
route Private_CeDATA 10.30.128.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.130.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.131.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.132.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.134.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.30.135.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.67.31.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 10.224.0.0 255.255.0.0 10.10.100.17 1
route Private_CeDATA 4.1.1.19 255.255.255.255 10.10.100.17 1
route Private_CeDATA 1.1.1.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 1.1.1.13 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.11.24 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.11.27 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.11.29 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.17.105 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.64 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.66 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.147.110 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.19.251.57 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.21.56.105 255.255.255.255 10.10.100.17 1
route Private_CeDATA 172.21.57.152 255.255.255.255 10.10.100.17 1
route Private_CeDATA 192.168.3.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.9.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.20.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.21.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.30.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.31.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.40.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.41.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.50.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.60.0 255.255.255.0 10.10.100.17 1
route Private_CeVOICE 192.168.61.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.70.0 255.255.255.0 10.10.100.65 1
route Private_CeVOICE 192.168.101.0 255.255.255.0 10.10.100.65 1
route Private_CeDATA 192.168.110.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.168.200.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 192.251.177.0 255.255.255.0 10.10.100.17 1
route Private_CeDATA 2.1.2.7 255.255.255.255 10.10.100.17 1
route Private_CeDATA 2.1.2.74 255.255.255.255 10.10.100.17 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server AD protocol nt
aaa-server AD (Private_ODATA) host 10.30.133.21
timeout 5
nt-auth-domain-controller Cool_Transformer_Name
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
aaa authentication serial console LOCAL
http server enable
http 192.168.69.0 255.255.255.0 management
snmp-server host Private_ODATA 10.30.133.67 poll community Some_*s_here version 2c
snmp-server location OT
snmp-server contact [email protected]
snmp-server community Some_*s_here
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
snmp-server enable traps syslog
snmp-server enable traps ipsec start stop
snmp-server enable traps entity config-change fru-insert fru-remove
snmp-server enable traps memory-threshold
snmp-server enable traps interface-threshold
snmp-server enable traps remote-access session-threshold-exceeded
snmp-server enable traps connection-limit-reached
snmp-server enable traps cpu threshold rising
snmp-server enable traps ikev2 start stop
snmp-server enable traps nat packet-discard
sysopt noproxyarp Public_Internet
sysopt noproxyarp Private_CDATA
sysopt noproxyarp Private_ODATA
sysopt noproxyarp Private_OVOICE
sysopt noproxyarp Private_CVOICE
sysopt noproxyarp Private_CeDATA
sysopt noproxyarp Private_CeVOICE
sysopt noproxyarp management
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map Public_Internet_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Public_Internet_map interface Public_Internet
crypto ikev1 enable Public_Internet
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet timeout 5
ssh 10.30.133.0 255.255.255.0 Private_ODATA
ssh 192.168.69.0 255.255.255.0 management
ssh timeout 2
ssh version 2
console timeout 5
dhcprelay server 10.30.133.13 Private_ODATA
dhcprelay enable Private_CDATA
dhcprelay timeout 60
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 10.30.133.13 prefer
ntp server 132.246.11.227
ntp server 10.30.133.21
webvpn
group-policy AO-VPN_Tunnel internal
group-policy AO-VPN_Tunnel attributes
dns-server value 10.30.133.21 10.30.133.13
vpn-tunnel-protocol ikev1
default-domain value ao.local
username helpme password Some_X's_here encrypted privilege 1
username helpme attributes
service-type nas-prompt
tunnel-group AO-VPN_Tunnel type remote-access
tunnel-group AO-VPN_Tunnel general-attributes
address-pool AO-VPN_Pool
authentication-server-group AD
default-group-policy AO-VPN_Tunnel
tunnel-group AO-VPN_Tunnel ipsec-attributes
ikev1 pre-shared-key Some_*s_here
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class class-default
user-statistics accounting
service-policy global_policy global
smtp-server 192.168.200.25
prompt hostname context
no call-home reporting anonymous
Thanks in advance,
Jeff. -
Site to Site VPN between ASA 5505 and Juniper SSG140 no traffic
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 3
interface Ethernet0/2
switchport trunk allowed vlan 20-21,24,28,212-214,227,232-236,254-256
switchport mode trunk
interface Ethernet0/3
switchport trunk allowed vlan 20-21,24,28,212-214,227,232-236,254-256
switchport mode trunk
interface Ethernet0/4
switchport trunk allowed vlan 20-21,24,28,212-214,227,232-236,254-256
switchport mode trunk
interface Ethernet0/5
switchport trunk allowed vlan 20-21,24,28,212-214,227,232-236,254-256
switchport mode trunk
interface Ethernet0/6
switchport trunk allowed vlan 20-21,24,28,212-214,227,232-236,254-256
switchport mode trunk
interface Ethernet0/7
switchport access vlan 250
interface Vlan2
nameif outside
security-level 0
ip address 81.XXX.XXX.XXX 255.255.255.252
interface Vlan3
nameif OUTSIDE_BACK
security-level 0
ip address 41.XXX.XXX.XXX 255.255.255.248
interface Vlan20
nameif XXX
security-level 80
ip address 10.143.0.1 255.255.255.0 standby 10.143.0.2
interface Vlan21
nameif XXX
security-level 90
ip address 10.143.1.1 255.255.255.0 standby 10.143.1.2
interface Vlan24
nameif XXX
security-level 80
ip address 10.143.4.1 255.255.255.0 standby 10.143.4.2
interface Vlan28
nameif XXX
security-level 80
ip address 10.143.8.1 255.255.255.0 standby 10.143.8.2
interface Vlan212
nameif SELF
security-level 80
ip address 10.143.12.1 255.255.255.0 standby 10.143.12.2
interface Vlan213
nameif XXX
security-level 80
ip address 10.143.13.1 255.255.255.0 standby 10.143.13.2
interface Vlan214
nameif BIOFR
security-level 80
ip address 10.143.14.1 255.255.255.0 standby 10.143.14.2
interface Vlan232
nameif MNGT
security-level 80
ip address 10.143.32.1 255.255.255.0 standby 10.143.32.2
interface Vlan233
nameif XXX
security-level 80
ip address 10.143.33.1 255.255.255.0 standby 10.143.33.2
interface Vlan234
nameif XXX
security-level 80
ip address 10.143.34.1 255.255.255.0 standby 10.143.34.2
interface Vlan235
nameif XX
security-level 80
ip address 10.143.35.1 255.255.255.0 standby 10.143.35.2
interface Vlan236
nameif XXX
security-level 80
ip address 10.143.36.1 255.255.255.0 standby 10.143.36.2
interface Vlan250
description LAN Failover Interface
interface Vlan254
nameif TEST
security-level 80
ip address 10.143.254.1 255.255.255.0 standby 10.143.254.2
interface Vlan255
nameif XXX
security-level 100
ip address 10.143.255.1 255.255.255.0 standby 10.143.255.2
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network XXX
subnet 10.143.14.0 255.255.255.0
object network XXX
subnet 10.143.35.0 255.255.255.0
object network XXX
subnet 10.143.1.0 255.255.255.0
object network MGMT
subnet 10.143.32.0 255.255.255.0
object network XXX
subnet 10.143.36.0 255.255.255.0
object network XXX
subnet 10.143.4.0 255.255.252.0
object network XXX
subnet 10.143.33.0 255.255.255.0
object network ACCT
subnet 10.143.34.0 255.255.255.0
object network XXX
subnet 10.143.0.0 255.255.255.0
object network XXX
subnet 10.143.8.0 255.255.255.0
object network XXX
subnet 10.143.12.0 255.255.255.0
object network XXX
subnet 10.143.37.0 255.255.255.0
object network TEST
subnet 10.143.254.0 255.255.255.0
object network XXX
subnet 10.143.255.0 255.255.255.0
object network NETWORK_OBJ_10.143.0.0_16
subnet 10.143.0.0 255.255.0.0
object network NETWORK_OBJ_10.91.0.0_16
subnet 10.91.0.0 255.255.0.0
object-group network vpn-local-network
network-object 10.143.14.0 255.255.255.0
network-object 10.143.35.0 255.255.255.0
network-object 10.143.1.0 255.255.255.0
network-object 10.143.32.0 255.255.255.0
network-object 10.143.36.0 255.255.255.0
network-object 10.143.4.0 255.255.255.0
network-object 10.143.33.0 255.255.255.0
network-object 10.143.34.0 255.255.255.0
object-group network vpn-remote-network
network-object 10.112.0.0 255.255.0.0
access-list ACL_VPN extended permit ip 10.143.0.0 255.255.0.0 10.112.0.0 255.255.0.0
access-list ACL_INSIDE_NONAT extended permit ip 10.143.0.0 255.255.0.0 10.112.0.0 255.255.0.0
access-list PING extended permit icmp any any
access-list PING extended permit icmp any any object-group ALLOW_PING
pager lines 24
logging asdm informational
mtu outside 1500
failover
failover lan unit primary
failover lan interface FAILOVER Vlan250
failover interface ip FAILOVER 10.143.250.1 255.255.255.0 standby 10.143.250.2
no monitor-interface outside
no monitor-interface OUTSIDE_BACK
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-721.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XXX interface
nat (XXX,outside) source dynamic XX interface
nat(IT,outside) source dynamic IT interface
nat (TEST,outside) source dynamic TEST interface
nat ( IT,outside) source dynamic IT interface
nat (TEST,outside) source static vpn-local-network vpn-local-network destination static vpn-remote-network vpn-remote-network no-proxy-arp route-lookup
access-group PING in interface outside
access-group PING in interface OUTSIDE_BACK
route outside 0.0.0.0 0.0.0.0 81.XXX.XXX.XXX.XXX 1 track 1
route OUTSIDE_BACK 0.0.0.0 0.0.0.0 41.XXXX
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
sysopt connection preserve-vpn-flows
sla monitor 123
type echo protocol ipIcmpEcho 41.xxx.xxx.xxx interface outside
frequency 10
sla monitor schedule 123 life forever start-time now
crypto ipsec ikev1 transform-set ESP-3DES-ESP-MD5-HMAC esp-3des esp-md5-hmac
crypto ipsec security-association pmtu-aging infinite
crypto map TEST 1 match address ACL_VPN
crypto map TEST 1 set peer 194.XXX.XXX.XXX
crypto map TEST 1 set ikev1 transform-set ESP-3DES-ESP-MD5-HMAC
crypto map TEST 1 set security-association lifetime seconds 86400
crypto map TEST 1 set security-association lifetime kilobytes 2147483647
crypto map TEST interface outside
crypto ca trustpool policy
no crypto isakmp nat-traversal
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
track 1 rtr 123 reachability
telnet timeout 5
ssh stricthostkeycheck
ssh 10.143.255.0 255.255.255.0 IT
ssh timeout 10
ssh key-exchange group dh-group1-sha1
console timeout 60
management-access IT
dhcpd lease 60000
dhcpd ping_timeout 20
dhcpd domain tls.ad
dhcpd auto_config outside
dhcpd address 10.143.4.10-10.143.4.200 XXX
dhcpd dns 10.91.0.34 8.8.8.8 interface XXX
dhcpd option 3 ip 10.143.4.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.12.10-10.143.12.200 XXX
dhcpd option 3 ip 10.143.12.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.14.10-10.143.14.200 XXX
dhcpd option 3 ip 10.143.14.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.32.10-10.143.32.100 MNGT
dhcpd option 3 ip 10.143.32.1 interface MNGT
dhcpd enable MNGT
dhcpd address 10.143.33.10-10.143.33.100 XXX
dhcpd option 3 ip 10.143.32.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.34.10-10.143.34.100 XXX
dhcpd option 3 ip 10.143.32.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.36.10-10.143.36.100 XXX
dhcpd option 3 ip 10.143.32.1 interface XXX
dhcpd enable XXX
dhcpd address 10.143.255.10-10.143.255.200 XXX
dhcpd option 3 ip 10.143.255.1 interface XXX
dhcpd enable IT
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp authenticate
ntp server 10.90.0.34
ntp server 10.91.0.34
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
group-policy DfltGrpPolicy attributes
vpn-idle-timeout none
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-clientless
username tlsnimda password OW03yrp6/wvkyg6E encrypted
tunnel-group 194.XXX.XXX.XXX type ipsec-l2l
tunnel-group 194.XXX.XXX.XXX ipsec-attributes
ikev1 pre-shared-key *****
class-map icmp
match default-inspection-traffic
policy-map icmppolicy
class icmp
inspect icmp
service-policy icmppolicy interface outside
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e820e629c3cbaf67478c065440ac8138
VPN is up but not passing any traffing
Crypto map tag: TEST, seq num: 1, local addr: 81.xxx.xxx.xxx
access-list ACL_VPN extended permit ip 10.143.0.0 255.255.0.0 10.112.0.0 255.255.0.0
local ident (addr/mask/prot/port): (10.143.0.0/255.255.0.0/0/0)
remote ident (addr/mask/prot/port): (10.112.0.0/255.255.0.0/0/0)
current_peer: 194.xxx.xxx.xxx
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 10, #pkts decrypt: 0, #pkts verify: 0
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#TFC rcvd: 0, #TFC sent: 0
#Valid ICMP Errors rcvd: 0, #Invalid ICMP Errors rcvd: 0
#send errors: 0, #recv errors: 10
local crypto endpt.: 81.xxx.xxx.xxx/0, remote crypto endpt.: 194.xxx.xxx.xx/0
path mtu 1500, ipsec overhead 58(36), media mtu 1500
PMTU time remaining (sec): 0, DF policy: copy-df
ICMP error validation: disabled, TFC packets: disabled
current outbound spi: CC4FACB7
current inbound spi : D8C0AC76
inbound esp sas:
spi: 0xD8C0AC76 (3636505718)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 9367552, crypto-map: TEST
sa timing: remaining key lifetime (kB/sec): (1824522239/3507)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
outbound esp sas:
spi: 0xCC4FACB7 (3427773623)
transform: esp-3des esp-md5-hmac no compression
in use settings ={L2L, Tunnel, IKEv1, }
slot: 0, conn_id: 9367552, crypto-map: TEST
sa timing: remaining key lifetime (kB/sec): (1824522239/3507)
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001
VPN is unstable
Connection terminated for peer 194.XXX.XXX.XX. Reason: Peer Terminate Remote Proxy 10.112.0.0, Local Proxy 10.143.0.0
I cannot pass any traffic through the vpn when it's UP, or ping the other side.
ASA VERSION 9.2I do not think that'll be any problem. Here at work we also use Cisco ADSL 800 Series with vpn between customers' sites without any issues. The ASA should vpn for sure.
-
VPN clients can connect via SSTP but not IKEv2 due to error 808
I have a Windows Server 2012 R2 with RRAS configured to allow SSTP / IKEv2 VPN connections. I'm using an external certificate for server authentication and the client authentication is done via domain username/password (Protected EAP). The clients can
connect successfully when using SSTP, but if IKEv2 is selected, then the following error is displayed:
Error 808:
The network connection between your computer and the VPN server could not be established because the remote server refused the connection. This is typically caused by a mismatch between the server's configuration and your connection settings. Please
contact the remote server's Administrator to verify the server configuration and your connection settings.
My external certificate has the Server Authentication EKU but not the IP security IKE intermediate, however it's the only
certificate installed, so I believe the certificate is OK.
Any ideas on what is causing the error?
Thank you.
Ricardo CostaHi,
What NAT device you are using? You must configure the IKEv2 related protocol on your NAT device too. For example if you are using the Cisco® NAT device you must
enable the IKEv2 support on the outside interface:
Enabling IKE on the Outside Interface
You must enable IKE on the interface that terminates the VPN tunnel. Typically this is the outside, or public interface. To enable IKEv1 or
IKEv2, use the crypto ikev1 | ikev2 enable command from global configuration mode:
=================================================
crypto ikev1 | ikev2 enable interface-name
For example:
hostname(config)# crypto ikev1 enable outside
=================================================
The related third party information:
Configuring IPSec and ISAKMP
http://www.cisco.com/c/en/us/td/docs/security/asa/asa84/configuration/guide/asa_84_cli_config/vpn_ike.html#wp1042302
You can refer the following KB to enable the RRAS logging.
RRAS: Logging should be enabled on the RRAS server
http://technet.microsoft.com/zh-cn/library/ee922651(v=ws.10).aspx
Hope this helps.
*** This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does
not control these sites and has not tested any software or information found on these sites; therefore, Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. There are inherent dangers
in the use of any software found on the Internet, and Microsoft cautions you to make sure that you completely understand the risk before retrieving any software from the Internet. ***
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Ask the Expert: FlexVPN and Internet Key Exchange Version 2 (IKEv2)
With Jay Young-Taylor
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about FlexVPN and IKEv2 with Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about FlexVPN and IKEv2 with Jay Young-Taylor. Feel free to ask questions on comparison between IKEv1 and IKEv2, What functions does IOS and ASA support, how does DMVPN and FlexVPN interoperate, or any related questions. . Feel free to ask questions on comparison between IKEv1 and IKEv2, What functions does IOS and ASA support, how does DMVPN and FlexVPN interoperate, or any related questions.
Remember to use the rating system to let Jay know if you have received an adequate response.
Jay might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Security sub-community discussion forum shortly after the event. This event lasts through January 25, 2013. Visit this forum often to view responses to your questions and the questions of other community members.Maykol,
Sorry for the delay in getting back to you here. Currently we are building some documents that clearly describe line by line (well, paragraph by paragraph) what is occurring in the finite state machine and what information is exchanged in the protocol. The articles have been writtne and are going through internal review before posting to cisco.com. We should have them out shortly.
You can enable "debug crypto ikev2", "debug crypto ikev2 packet", and/or "debug crypto ikev2 error" and follow the packet flow. The debugs themselves have been re-written a couple of times to make the action/work flow more human readable and in plain english. It should be easier to understand with the later 15.1 - 15.2 code versions.
The debugs are broken up based on us sending a packet (look for "Tx Packet") and recieving a packet (loof for "Rx Packet"). In addition you can keep track of a single session by looking at the initator and responder (IKEv2) spi. Those values will never change during the session life time.
-Jay -
ASA 8.4 troubleshooting steps..
Hi guys,
Can you please help me out with troubleshooting steps for ASA FW.Well, without knowing much more about your network, the trouble shooting steps for site to site would be as follows:
1. make sure that both sites have the same crypto policy map parameters configured
2. make sure that both sites have the same transform set parameters configured
3. if using preshared key, make sure the tunnel group is configured with the correct key at both sites
4. make sure that the crypto ACLs at both sites are mirror images of eachother.
5. make sure you have applied the crypto map to the outside interface
6. depending on your ASA version, make sure you have enabled ikev1 or ikev2 (depending on which version you are using) on the outside interface.
For the remote access VPN it depends on if you are using AnyConnect VPN or IPsec VPN.
To troubleshoot further you can use debug commands to get more info and fine out if there are issues in either ike phase1 or phase 2 of the VPN establishment.
debug crypto isakmp sa
debug crypto ipsec sa
newer versions
debug crytpo ikev1
debug crytpo ipsec
Please remember to select a correct answer and rate helpful posts -
Routing issue with ASA and UC540 phone system - at ASA???
Having an issue with routing from the PC at .242 to the CUE server at 10.1.10.1. The CUE server is built into the UC540 phone system. It is an internal piece of software that is used for voicemail and management. The UC540 is not only a call router, it is also an IOS router. It has it's own WAN connection as does the ASA.
Here are some facts:
1. Can ping the UC540's internal CUE server from the PC ( ping to 10.1.10.1 )
2. Can ping the UC540's VLAN 1 address from the PC ( ping to 10.1.10.1 )
3. The ASA is the default gateway for the PC.
4. I have a route inserted at the asa that is:
route 10.1.10.1 255.255.255.0 10.19.250.254 1
5. I have a nat statement that prevents NAT from occuring but I don't think this is necessary as the 10.1.10.0/24 network isn't otherwise defined on the ASA.
6. I cannot pull up a web page when I point the browser on the PC to the 10.1.10.1 address
7. I CAN pull up a web page on the PC when I create a static route on the PC iteslf :
route add 10.1.10.1 mask 255.255.255.0 10.19.250.254
Is is only with this route that I am able to get to the web GUI on the phone system.
8. The phone system has a loopback interface at 10.1.10.2 that serves as the gateway for the internal CUE server, the internal CUE server is at 10.1.10.1
9. The switch is a 2960 and has a trunk port to the phone system to allow for the voice vlan which is at 10.1.1.0/24, no issues with this vlan and phones are connecting to the system fine.
Since I can get the GUI to come up when I set a static route on the PC, then I would assume that the routing in the phone system with it's internal server is fine as it wouldn't work otherwise. Since I can successfully ping the CUE server from the PC, that would lead me to believe that the ASA's routing is setup correctly..... TCP traffic doesn't seem to get to/from the CUE server.
Here are the routing tables:
ASA:
Gateway of last resort is xxx.xxx.xxx.xxx to network 0.0.0.0
C xxx.xxx.xxx.xxx 255.255.255.252 is directly connected, outside
S 172.16.100.100 255.255.255.255 [1/0] via 38.97.193.65, outside
S 10.1.10.0 255.255.255.252 [1/0] via 10.19.250.254, inside
C 10.19.250.0 255.255.254.0 is directly connected, inside
S* 0.0.0.0 0.0.0.0 [1/0] via xx.xx.xx.xx, outside
The UC540 phone system's router side:
Gateway of last resort is xx.xx.xx.xx to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via xx.xx.xx.xx
10.0.0.0/8 is variably subnetted, 7 subnets, 4 masks
C 10.1.1.0/24 is directly connected, BVI100
L 10.1.1.1/32 is directly connected, BVI100
C 10.1.10.0/30 is directly connected, Loopback0
S 10.1.10.1/32 is directly connected, Integrated-Service-Engine0/0
L 10.1.10.2/32 is directly connected, Loopback0
C 10.19.250.0/23 is directly connected, BVI1
L 10.19.250.254/32 is directly connected, BVI1
XX.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C XX.XX.XX.XX/29 is directly connected, FastEthernet0/0
L XX.XX.XX.XX/32 is directly connected, FastEthernet0/0
172.16.0.0/24 is subnetted, 1 subnets
S 172.16.100.0 [1/0] via 10.19.250.1
The UC540's internal CUE server:
Main Routing Table:
DEST GATE MASK IFACE
10.1.10.0 0.0.0.0 255.255.255.252 eth0
0.0.0.0 10.1.10.2 0.0.0.0 eth0
Any help appreciated!!!
Thanks!Hello,
Where you able to solve this problem? It does sound like an issue with TCP state checking on the ASA. The Firewall needs to see both sides of the traffic but the return traffic is going from your UC540 direct to the PC. The firewall essentially kills the traffic.
I would recommend disabling TCP state checking on the ASA and see if it works. Otherwise, you will need to stub route the UC540 as a separate VLAN off the ASA which needs to route through the ASA to reach the PC.
Here is a info page on the TCP State Bypass:
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/111986-asa-tcp-bypass-00.html
Please let me know how it works out.
Maybe you are looking for
-
Deploy New SampleApp in obiee 11g
Hi Friends, I am deploying SampleApp in obiee 11g.I am installing "AnalyticsRes" in console. Can anyone give me suggestions what is the use of "AnalyticsRes" and what is happening after installing of "AnalyticsRes". I got +AnalyticsRes -Web Services
-
On my PC, I cannot run itunes, I keep getting this error message" Quick Time failed to initialized (error02096) Quick time is required to run please unistall itunes then install itunes again, I have done this three times and I keep getting the same e
-
How do I get my slider to move when I click the groove
TheI have created a simple Adobe Flash movie which is to act as a slider control. The code that I have written is shown below. I am able to grab the slider and move it to any position on the groove but I wish to also be able to click anywhere on the
-
Don't want column width in new document window
Suddenly, and I can't determine why, my InDesign CS2 has started putting column width as an option in the New Document window. It didn't used to do that. I don't want that to be there. Anyone have any suggestions?
-
I'm trying to redeem a gift code from IGN's Free Game of Month, but I can't! It's "The Wolf Among Us Episode 1". It says that the app contains age-resreicted material and asks to tap OK. But nothing happens after I press the button! What should I do?