ASMCMD-08103: failed to connect to ASM; ASMCMD running in non-connected mod

Hi,
I am facing below problem.
ASMCMD-08103: failed to connect to ASM; ASMCMD running in non-connected mode
ASMCMD-08102: no connection to ASM; command requires ASM to run
Probable reasons are:
1. ORACLE_SID is not set properly
2. ASM instance is not running.
But my ORACLE_SID is set properly and ASM instance is also running...
What else i can check?
Thanks,

======================================================
[oracle@aveo:~]>lsnrctl services
LSNRCTL for HPUX: Version 11.1.0.6.0 - Production on 18-AUG-2010 12:08:05
Copyright (c) 1991, 2007, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
Services Summary...
Service "+ASM" has 1 instance(s).
Instance "+ASM", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "+ASM_XPT" has 1 instance(s).
Instance "+ASM", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "MIG11A2" has 1 instance(s).
Instance "MIG11A2", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "MIG11A2_XPT" has 1 instance(s).
Instance "MIG11A2", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "Q111REG" has 1 instance(s).
Instance "Q111REG", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "Q111REG_XPT" has 1 instance(s).
Instance "Q111REG", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "QA111REG" has 1 instance(s).
Instance "QA111REG", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
Service "QA111REG_XPT" has 1 instance(s).
Instance "QA111REG", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:0 refused:0 state:ready
LOCAL SERVER
The command completed successfully
======================================================

Similar Messages

The connection pool DIMT_DB is running out of connections

I am facing an issue, the process instances created in activity are not getting routed to my work item. I found the following exception logged in engine DB at the time process instance was created,
The connection pool DIMT_DB is running out of connections ( 100 % of the pool is in use).
It is recommendable to expand the size through the Process Administrator.
can anyone provide me a solution to this issue?
the maximum pool size is 10. should it be increased?
does this issue occur when database connection is not closed properly?

Can anyone please share your ideas?
Thanks,

Issues connecting to ASM instance.

Hi,
I set the ORACLE_SID=+ASM1
export ASM_BASE=/u101/app/asm
export ASM_HOME=$ASM_BASE/product/11.1.0
But when i am trying to connect asmcmd utility.
[oracle@dldb1 ~]$ asmcmd
ASMCMD-08103: failed to connect to ASM; ASMCMD running in non-connected mode
Do i am setting wrong parameters? Please advice me.
Thanks

thank you for you kind.. I forgot it... but after I modify tnsname.ora, Error number changed..
tnsname.ora:
# tnsnames.ora Network Configuration File: E:\oracle\product\11.2.0\dbhome_1\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
ITPUB =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = rac-cluster-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = itpub)
+ASM =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = rac-cluster-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = +ASM)
*>sqlplus /nolog*
SQL*Plus: Release 11.2.0.1.0 Production on Wed Jul 7 12:50:07 2010
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> connect sys@+asm as sysasm
Enter password:
ERROR:
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor
SQL>
tnsping +asmTNS Ping Utility for 64-bit Windows: Version 11.2.0.1.0 - Production on 07-JUL-2
010 12:51:09
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
E:\oracle\product\11.2.0\dbhome_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = rac-clus
ter-scan)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = +as
m)))
OK (20 msec)

ORA-12154: Error when connecting to asm instance

hi all, I am now facing new problem with asm of clusterware, I failed to connect to asm instance, there is how I did it:
sqlplus /nologSQL*Plus: Release 11.2.0.1.0 Production on Wed Jul 7 04:58:52 2010
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> connect sys@+ASM as sysasm
Enter password:
ERROR:
ORA-12154: TNS:could not resolve the connect identifier specified
I consider listener is correct configed.
lsnrctl statusLSNRCTL for 64-bit Windows: Version 11.2.0.1.0 - Production on 07-JUL-2010 08:51:49
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 64-bit Windows: Version 11.2.0.1.0 - Produ
ction
Start Date 05-JUL-2010 22:12:29
Uptime 1 days 6 hr. 39 min. 23 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File E:\app\11.2.0\grid\network\admin\listener.ora
Listener Log File e:\app\11.2.0\grid\log\diag\tnslsnr\rac1\listener\aler
t\log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\LISTENERipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=192.168.0.110)(PORT=1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=192.168.0.112)(PORT=1521)))
Services Summary...
Service "+ASM" has 1 instance(s).
Instance "+asm2", status READY, has 1 handler(s) for this service...
Service "itpub" has 1 instance(s).
Instance "itpub2", status READY, has 1 handler(s) for this service...
Service "itpubXDB" has 1 instance(s).
Instance "itpub2", status READY, has 1 handler(s) for this service...
The command completed successfully
How to resolve the promblem? Best regards..

thank you for you kind.. I forgot it... but after I modify tnsname.ora, Error number changed..
tnsname.ora:
# tnsnames.ora Network Configuration File: E:\oracle\product\11.2.0\dbhome_1\network\admin\tnsnames.ora
# Generated by Oracle configuration tools.
ITPUB =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = rac-cluster-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = itpub)
+ASM =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = rac-cluster-scan)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = +ASM)
*>sqlplus /nolog*
SQL*Plus: Release 11.2.0.1.0 Production on Wed Jul 7 12:50:07 2010
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> connect sys@+asm as sysasm
Enter password:
ERROR:
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor
SQL>
tnsping +asmTNS Ping Utility for 64-bit Windows: Version 11.2.0.1.0 - Production on 07-JUL-2
010 12:51:09
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
E:\oracle\product\11.2.0\dbhome_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = rac-clus
ter-scan)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = +as
m)))
OK (20 msec)

Hi there, I am trying to connect to my server at work from home using a vpn connection. It connects fine and the time ticks along, but when i click go - connect to server, it comes up with connection failed. Please help!

Hi there, I am trying to connect to my server at work from home using a vpn connection. It connects fine and the time ticks along, but when i click go - connect to server, it comes up with connection failed. Please help!

... when i click go - connect to server, it comes up with connection failed.
If you're trying to connect to a Bonjour server on the remote network, that won't work over a layer 3 VPN. Use something like Hamachi or one of the SSH-tunnelling Bonjour proxy apps for that.

Sql server agent job failing to connect excel connection manager of SSIS package by 32-bit mode run time

I am unable to succeed with sql agent job, I am trying to execute the SSIS package through sql agent job by ticking 32 bit runtime check box in 64 bit machine , even it does not worked..
could any one helpme on this?
Source: Excel Load Connection manager "Excel Connection Manager"
Description: SSIS Error Code DTS_E_OLEDBERROR. An OLE DB error has occurred. Error code: 0x80040154. An OLE DB record is available. Source: "Microsoft OLE DB Service Components" Hresult: 0x80040154 Description: "Class
not registered". End Error TS_E_CANNOTACQUIRECONNECTIONFROMCONNECTIONMANAGER. The AcquireConnection method call to the connection manager "Excel Connection Manager" failed with error code 0xC0202009. There may be error
messages posted before this with more information on why the AcquireConnection method call failed. End... The package execution fa... The step failed.

Hello Keerthi,
Can you please modify settings and set delay validation for Excel connection manager? I think its validating connection and failing because it might be picking that from some variable.
Alternatively, please run package using below and see what happens.
EXEC master..xp_cmdshell 'DTEXEC.exe /SQL "Folder\Package" /SERVER Servername'
I will recommend you to follow steps in below link.
http://www.sqlhammer.com/blog/running-ssis-packages-in-32-bit/
Regards,
Vishal Patel
Blog: http://vspatel.co.uk
Site: http://lehrity.com

My time machine backup external hard drive has failed. I have a newer external drive already connected to my MAC but can't figure out how to get Time Machine to set up on it?

My time machine backup external hard drive has failed. I have a newer external drive already connected to my MAC but can't figure out how to get Time Machine to set up on it

http://pondini.org/TM/21.html

Could not open connection to the host, on port 23: Connect failed

Can anyone please help with this telnet problem on CISCO 877 ADSL Router
I am trying to telnet into my ISP Router remotely using public IP which has been dynamically assigned to the router by the ISP.
I can Ping the Router and I can also go out to the internet on that router but, I can not telnet into that router from Inside the Network nor Outside the Network. There are no Firewalls involved.
I have tried to clear the config and reconfigure it again, it does not help, I have also applied same config on another CISCO 877 ADSL Router it still does not work.
ERROR i get on the Command Prompt: Could not open connection to the host, on port 23: Connect failed
I have shown some of the Show Run out put below if that helps,
ip nat inside source list 1 interface Dialer0 overload
access-list 1 permit x.x.x.x 0.0.0.7
dialer-list 1 protocol ip permit
line vty 0 4
password 7 ***********
login
Manny Thanks
Punit

Find Below the Requested Sh run outputs
ADSL-ROUTER1#sh run | beg line vty
line vty 0 4
password 7 ***********
login
scheduler max-task-time 5000
end
I have removed the IP for security reasons
ADSL-ROUTER1#sh ip route
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
     x.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
S       x.x.x.x/29 is directly connected, Vlan1
C       x.x.x.x/32 is directly connected, Dialer0
     x.0.0.0/32 is subnetted, 1 subnets
C       x.x.x.x is directly connected, Dialer0
S*   0.0.0.0/0 is directly connected, Dialer0
I also keep getting the message below on the console done know if this is part of the problem
Mar 13 07:17:32.213: %IP_VFR-4-FRAG_TABLE_OVERFLOW: Vlan1: the fragment table h
as reached its maximum threshold 16
Hope this output helps
Thanks

Failed to sqlplus into ASM with the notorious ORA-12505 error

Hi guys,
I have a 2-node RAC testing environment and i have been having trouble trying to LOCALLY sqlplus into the ASM instance.
If I do "sqlplus sys/xxxxx@asm1", it just throws "ORA-12505:TNS: listener does not currently know of SID given in connect descriptor".
If I do "sqlplus / as SYSASM", it says "ORA-01031: insufficient privileges".
Can' figure out where I did wrong so really appreciate some help here (maybe in the listener file, i should give the GRID home for one of the ORACLE_HOME parameters)?
Here is the tns and listener file:
tnsnames.ora:
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = vbox-cluster)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
ASM1 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = vbox-cluster)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SID = +ASM1)
listener.ora:
LISTENER=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER)))) # line a
dded by Agent
LISTENER_SCAN1=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER_SCAN1))))
# line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER_SCAN1=ON # line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER=ON # line added by Agent
SID_LIST_LISTENER_ASM=
(SID_LIST=
(SID_DESC=
(SID_NAME=PLSExtProc)
(ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)
(PROGRAM=extproc)
(SID_DESC=
(ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME=+ASM1)
)

user11957149 wrote:
Hi guys,
I have a 2-node RAC testing environment and i have been having trouble trying to LOCALLY sqlplus into the ASM instance.
If I do "sqlplus sys/xxxxx@asm1", it just throws "ORA-12505:TNS: listener does not currently know of SID given in connect descriptor".
If I do "sqlplus / as SYSASM", it says "ORA-01031: insufficient privileges".
Can' figure out where I did wrong so really appreciate some help here (maybe in the listener file, i should give the GRID home for one of the ORACLE_HOME parameters)?
Here is the tns and listener file:
tnsnames.ora:
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = vbox-cluster)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = ORCL)
ASM1 =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = vbox-cluster)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SID = +ASM1)
listener.ora:
LISTENER=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER)))) # line a
dded by Agent
LISTENER_SCAN1=(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=IPC)(KEY=LISTENER_SCAN1))))
# line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER_SCAN1=ON # line added by Agent
ENABLE_GLOBAL_DYNAMIC_ENDPOINT_LISTENER=ON # line added by Agent
SID_LIST_LISTENER_ASM=
(SID_LIST=
(SID_DESC=
(SID_NAME=PLSExtProc)
(ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)
(PROGRAM=extproc)
(SID_DESC=
(ORACLE_HOME=/u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME=+ASM1)
)with regard to ASM instance, it is NEVER "online"
There is never any requirement to connect to ASM instance via SQL*Net.
Log onto DB Server directly & just start ASM instance

Log connection attempts and source IP address for connections that fail/timeout on RADIUS

How can I log the connection attempts and source IP address for connections that fail RADIUS authentication? I'm using RD Gateway on 2012 R2 in conjunction with Azure Multi-Factor Authentication Server on another 2012 R2 server. When a user fails
multifactor authentication or the authentication times out, all I get is Security event 6273 on the RD Gateway that the radius server did not process the request, and only the radius server's IP is logged. There's nothing logged in TerminalServices-Gateway\Operational
because the TS Gateway hasn't yet processed the connection attempt (all auditing options for RD Gateway are enabled). The MFA/Radius Server is only logging the connection from the TSGateway - it doesn't know the original client's IP address.
I'm looking for the equivalent of an IIS log - somewhere the RD Gateway should log the initial HTTPS connection attempt and the source IP address of the client. I need to be able to track down potentially fraudulent login attempts.

Hi,
Thank you for your posting in Windows Server Forum.
This error might be caused by one of the following conditions:
• The user does not have valid credentials
• The connection method is not allowed by network policy
• The network access server is under attack
• NPS does not have access to the user account database on the domain controller
• NPS log files or the SQL Server database are not available
To perform these procedures, you must be a member of Domain Admins.
Please check for more information:
Event ID 6273 — NPS Authentication Status
http://technet.microsoft.com/en-us/library/cc735399(v=ws.10).aspx
Hope it helps!
Thanks.
Dharmesh Solanki

HT4061 my phone failed to update and now only shows symbols to connect to itunes but wont connect. suggestions?

my phone failed to update and now only shows symbols to connect to itunes but wont connect. suggestions?

Put the device in DFU mode (google it) and restore.

After updating my iPhone 4s to iOS 6.1, Verification Failed: An SSL error has occurred and a secure connection to the server cannot be made. My wifi connection works; the icon is present at the top left. But Internet won't connect, be it Safari, App Store

After updating my iPhone 4s to iOS 6.1, Verification Failed: "An SSL error has occurred and a secure connection to the server cannot be made." My wifi connection works; the icon is present at the top left. But Internet apps won't connect, be it Safari, App Store or Facebook & instagram. Push notifications also work so posts from Facebook and Instagram still pop-up. Does any one have any ideas? Thanks.

I have the same problem. Worked fine on Friday. My VPN or any ssl site do not work on my iPhone 5. Both work perfect on iPhone 4 and 4s

Ipod restore failed can see on the screen is the cable connection symbom and the ipod does not appear in the LH panel of itunes is there an easy solution to this

ipod restore failed can see on the screen is the cable connection symbom and the ipod does not appear in the LH panel of itunes is there an easy solution to this

To get iTunes to see your iPod try:
- Placing the iPod in recovery mode. See:
iPhone and iPod touch: Unable to update or restore
- Placing it in recovery DFU mode:
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Sometimes this program will get th iPod in recovery mode:
RecBoot iPod-1.0.2-Mac-Jaxov.zip - File Shared from Box.net - Free Online File Storage

Telent:could not open connection to the host on port 23 connect failed

Hi,
How to run commands of OEL5 host OS from windows XPP virtual machine(Vmware Player) on standalone desktop PC?
While runing the telnet command on windows XPP virtual machine it's gives error
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\Administrator>cd\
C:\>telnet 192.168.1.2
Connecting To 192.168.1.2...Could not open connection to the host, on port 23: Connect failed
C:\>
Thanks
Regard
GSM

user9230833 wrote:
Launcher means shortcut to execute any file which is inside folder in Linux.Launcher are created on desktop to execute by one click of mouse.You need to create a command file that contains the required instructions to run putty with whatever relevant command line switches in order to start the remote program/process on Linux.
For example, you have a trusted ssh connection (no password prompting) between your Windows account and the Linux vmware account. You need to execute command line +/home/vmware/bin/vmstart myVM+ on Linux.
Your command file in Window will look something as follows:
@echo off
"c:\program files\putty\pssh.exe" vmware@my-linux-server "/home/vmware/bin/vmstart myVM"Once you've create this command file (.cmd file extention), you can create a desktop shortcut for it and assign an icon to it.
However, first test the command file via an interactive console session to ensure it works. Also, I'm not sure you can script telnet using putty - but putty's ssh does support the standard ssh command line and one can execute programs/commands on the remote server in this fashion.
Setting up trusted ssh connections is also important as passwords is a weak security mechanism. It requires a secret to be used and coded into scripts/software that needs to be authenticated.
With ssh you generate a public/private key combination, and provide the public key as unique identifier for your o/s user and platform to a remote server (e.g. Linux). This now enables your platform and o/s user to be authenticated via the privatre/public key pair when your platform establishes a connection with the server.
In putty, generate a ssh key (RSA). Copy and paste the public key into the Linux server account's "+home/vmware/.ssh/authorized_keys+" file. Make sure that the +.ssh+ directory and key have user read/write permissions only. And that's it - no password needed by your account to ssh into the Linux server account. No secrets that need to be kept secret (and that can be stolen and used from any other platform to gain access).

HT6162 Hi guys, I downloaded this new iOS7.1 but it always fails to install. It says I am not connected to the Internet while I have all the network and second excuse it gives is that the software update is currently unavailable. Please help.

Hi guys, I downloaded this new iOS7.1 but it always fails to install. It says I am not connected to the Internet while I have all the network and second excuse it gives is that the software update is currently unavailable. Please help.

Hi Romantilizer,
Hook your phone up to iTunes on the computer you sync with and do your update from there. This is a robust iOS release, and doing it OTA is not always successful. I tried on my iPhone a couple of times, and it aborted the update twice. Did it via the Mac, and it was fine.
It takes a bit of time, so hook it up, make sure it is updating your phone, and then find something else to do for a couple of hours.
Cheers,
GB

ASMCMD-08103: failed to connect to ASM; ASMCMD running in non-connected mod

Similar Messages

Maybe you are looking for