Audigy SE SB0570 microphone impeda

I read previous threads and answers about the impedance (from Tiger) . Forgive me, just want to be sure and place my questions:?. for my Audigy SE SB0570 the microphone impedance is ~ 600 ohm, right?2. what is the approximate range of microhones impedance to work moreless correctly with Audigy ? - say?from 400 ohm to 800 ohms?Will be grateful for the comment.

John, thank you for the quick answer. At the moment I am using cheap EasyTouch microphone + headphones. My friends I talk on Skype say my voice is good quality.What is strange to me, the microphone I use with the Audigy SE has impedance?2200 ohm !http://www.easytouch.pl/product6074.PL.html?After I know the Audigy microphone impedance is 600 ohms, I am quite confused - it should not work well with 2200 ohm, but somehow it does.Could you comment it, please?Grtgs.

Similar Messages

SB Audigy SE (SB0570) / Win 8.1 64bit completely freezes on sound playback

hi there,
I got a problem: my audigy se doesnt work on windows 8.1 64bit.
I freshened up my pc and installed a clean win 8.1 os on a new harddrive.
I tried installing the official SB24_PCDRV_LB_1_04_0090a.exe driver.
I got a audigy se (sb0570), and driver installation works fine. the card got recognized and it can play a sound, but after a few seconds my whole PC freezes without bluescreen. it doesnt matter if it is a flash video, a mp3 or just a windows sound; it always freezes. when the sound device is disabled, the system runs without freezes. I can start a playback, ofc there is no sound, but the system is stable.
my card works fine on win 7 64bit with older drivers. plus, I am using the support pack 2.6 by daniel_k (I still use my old SDD with win7 on it and everything works fine). I also tried support pack 2.6 on my win 8.1 system but it doesnt even recognize the card. the newer support pack 3.0 does recognize sb0570 and actually the sound works for about 10seconds (my 5.1 system works fine for that 10 sec, all speakers are getting a signal, but then it freezes...).
so, both the official and the unofficial drivers are not working.
has any1 a clue?

IRe: SB Audigy Series Support Pack 3.0 + DTS Encoder Switcher (08/28/2009).
blunden wrote:
EddieObscurant: 4. works fine for me in AC3. I use AC3filter though and it has it's own speaker settings. Perhaps that helps until the next release.
daniel_k: I uploaded it to 4shared.com and MediaFire for you since I don't really like Rapidshare. I hope you don't mind.
http://www.4shared.com/file/302793/e9678376/Audigy_SupportPack_3_0.html
http://www.mediafire.com/download.php?rjmznqa2oy
Sure I don't mind, thanks for helping, but I've?just uploaded an updated package, version 3..
Fixes an issue that prevents Speaker Fill from working.
There is also a hotfix in the main post, so those who have already installed Support Pack 3.0 don't need to reinstall.

Audigy se sb0570 win_7 32_bit

Good day,
I have two HP D330 Personal computers and I installed Windows 7 32 bit for an update.
The Audigy SE sb0570 does not work under Win_7. It seems to me that ths OS does note reconise the board because of the driver. The dri've I did use have been suggested by Creative ! ( see Creative site )
I am sure the two audio boards on my hands are working properly under windows XP sp2.
I do not have any valid help from Creative.
Any suggestion for me ?
Any particular procedure to follow ?
Any help is appreciated.
Thanks
Ambrogio

Since I have a Macbook Air and an iMac I have to wait to install the software. However, I spoke with Microsoft and they assured me that it will work & if it doesn't they will give it over to a senior engineer. As long as I have the original disk and serial number, they have no problem with it. BTW, just for your knowledge they have cleaned up their act and assist customers with reinstallation issues. So if you ever have a problem they will help you. I had a senior engineer that worked with my son's old laptop with Vista and scheduled phone calls at my convenience to troubleshoot. It's nice to know that Apple and Microsoft have made peace with each other......

Audigy 4 Pro microphone problems in Win 7 64-bit

Hi there,
Since I put my Audigy 4 Pro card into my newer PC with Win 7 64-bit the microphone only seems to work when it wants to, or works but sounds messed up.
I've waited a while before posting about this because I thought the newer drivers would sort out the problem, but it remains the same.
The card/microphone works without a problem if I put it in a PC with Win XP.
Sometimes the microphone will not pick up any sound at all. Other times it will work, but only for? game, say Heroes of Newerth. Then in Windows using teamspeak, people describe the sound like I'm talking through a fan. Tried using the in-game VOIP but I get the same result.
After a restart or just some random day, people in Heroes of Newerth would discribe the VOIP from my side as if I was talking under water(or through a fan), but then it would work fine for teamspeak or Bad Company 2 or any other game. I used these 2 games as an example since its what I'm playing mostly at the moment.
There doesnt seem to be any consistancy with the problem.
I have recently removed the sound card from my PC and now forced to use the onboard sound that reminds me of the sound of a clockradio.
My PC specs are:
Asus Rampage Formula Motherboard
Intel Core 2 Duo 3.0GHz E8400
8GB RAM
4 x WD Raptor HDD Stripe RAID
ATi Radeon 4870 52MB
Sound Blaster Audigy 4 Pro?(model number shown?is SB0290)
Using?a Sennheiser PC350 Headset.
What I have tried my side so far:
Tried latest and older drivers for Win 7 64-bit
Reinstalled Windows 7 several times with different drivers.
Tried disabling all devices except for line/mic
Tried other input devices.
Tried with different audio and sound codecs, tried without any.
Might have been or 2 other things I tried I cannot think of now.
Is there anyone that experienced similar problems and got it fixed? Any help would be appreciated.

Hi Bill,
Can you be more specific about which steps were not recorded?
There some things that will not be recorded. The release notes list some known issues.
Known Issues:
Tutorial Builder can only capture actions in Photoshop that are recorded by the ScriptListener plug-in. While this includes most of Photoshop's functionality, some features/tools are not recorded. In particular, brushing actions are not captured. We hope to address this in future releases of Tutorial Builder.
Some of the the actions that Tutorial Builder captures are not yet instrumented to produce detailed text instructions in the final tutorial. For such actions, the generated tutorial will include a step that says "The (action name) is not yet supported by Tutorial Builder," and the tutorial author will have to edit the HTML to provide more descriptive text. Note that the "Show me in Photoshop" link is still generated for such actions.
Some Photoshop actions allow the user to specify a set of parameters in multiple ways, but Tutorial Builder cannot detect how the user specified those settings during the recorded demonstration. Thus, the text in the generated tutorial may not describe exactly what was demonstrated. For example, in the Image > Adjustments > Levels tool dialog box, you can update the parameters using three different eye droppers. Since Tutorial Builder does not know which (if any) of these eye droppers were used, the text for a Levels adjustment does not describe exactly how the settings are specified. Again, the tutorial author can simply edit the HTML to provide a more accurate description.
Thanks!
Mira

Audigy 2 ZS + Microphone Is

I have an incredibly annoying problem with my microhpone, and it seems a great deal of other people do as well. I'm using an Altec Lansing AHS602i Gaming Headset on an Audigy 2 ZS Platinum Pro. Both my headphones and mic cable have 6.5mm connections attached to them and are connected to the front of my I/O dri've. The output volume on my headphones and the recording quality on my mic is fine. It's the mic output volume that is extremely low. Even with all volume/mic settings turned up in the volume control panel, in games, on my headset and on my I/O dri've, the recording volume is barely audible.
Also, I have an issue with steam games. When I start up a steam game, such as Half-Life or Half-Life 2, my recording device is automatically changed to Wave, when my recording device was initially set to Line-In /Mic before I started up the game. The only solution I've found for this is to alt tab into windows and set the recording device back to Line-In /Mic, then alt tab back into the game. I've tried changing the command "voice_forcemicrecord" from to 0, but that didn't help.
Is there a solution to either of these issues? Is Creative working on new drivers that will fix these issues?Message Edited by skulleh on 09-28-2005 04:0 AMMessage Edited by skulleh on 09-28-2005 04: AM

This is down to the game itself. As long as you set the mixer for the card to the settings you want, that's all you need to do on the card.
Here is a specific page on the Steam website, referring to a problem like this:
http://support.steampowered.com/cgi-...hp?p_faqid=237
And some generic microphone troubleshooting/settings:
http://support.steampowered.com/cgi-...php?p_faqid=26
If those don't help, I'd advise you contact them directly to see what they advise, it seems to be down to the game itself, it defaults to the mic setting rather than accept the record setting you have chosen in the mixer.
Cat

Audigy 2 ZS Microphone problems & SBA2_PCWDRV_LB_1_84_55-R1 patch FAO Jerem

Jeremy - Creative's Audigy 2 ZS card DOES NOT appear to work properly with a selection of both basic and more expensi've microphones. There is some pick up of sound but at a very low level making most chat and telephony software useless. I have had this problem from Day with your card in an expensi've top of the line DELL desktop. DELL engineers who man a dedicated line for the particular machine I purchased have not been able to explain or resolve the issue - even on-site. I can't see any post from you or your team that addresses this satisfactorily. DELL have replaced the sound card to no avail which rules out a specific faulty card, the XP pro OS has been re-installed etc and please, please - yes, the sound level is up full and the 20dB boost has been applied etc etc etc. Having spoken to DELL, it would seem that there is a growing body of complaints from customers about this issue. I suppose , if not already, your may have these referred to your company as the OEM supplier. Finally, like many others, your 2th May driver patch won't load. Again, I guess you know what the error message says by now. Again, I see no solution to this one. I would be grateful if you can spell out how to resolve the mic issue. What do you suggest ? Regards,

Yeah, I have this prblem too. I went to the automatic update page & it showed a bunch of updates. I ran the 0303.exe update which is required for _84_55-R.exe. Rebooted the system, reran auto updates, and no updates showed up. Downloaded the file manually & when I ran it, install said it couldn't find an audigy card!! What the heck is going on here?
Also, does anyone a good method for installing this card on XP? I have tried installing it with SP & then running SP2. Each gives a different install. If you install the card with SP and then update to SP2, you get a remote icon in the system tray. If you install the card after SP2, there is no remote center available; but you get a play center icon in the quick launch area. Why do you get a different install depending on the XP service pack?

Sound Blaster Audigy 2 ZS Microphone H

Ok, I just bought a brand new Microphone, a Sennhesier pc-50 and a brand new sound blaster audigy 2 ZS. When i go to test my mic in a team-speak server of mine, the green button wont light up at all (meaning it wont work). The odd thing is, people in team-speak hear key clicks, my msn beeps, and music that i play, but not my voice. I've tried to switch the wires around while recording myself but it still wont work. I also looked to see if i placed my head phones in the right slot, and the mic in the right slot and it still wont work. The headphones are brand new, and work on another computer. Its just not working on this one. Please help

Hello and welcome to the club. There are tons of use out here.. with the same problem.. Seems we have to sit tight.. they have not let us know a THING about our problem.. Whether or not they are looking into this or otherwise. No one has had the problem solved.. and if someone has and reads this .. LET US KNOW. At the moment, however, I have learned one thing based on this problem: Don't buy any more SB / CL Products!!!

Audigy 2 value microphone auto-adj

I'm having a problem with my creative software auto-adjusting the recording level when I use my microphone; the louder I speak, the lower the input level goes, so the louder I have to speak. I'm using it to record to another program and having the levels change on me all the time is really messing things up. Anyone know how to turn this "feature" off?

The analog outputs and the mic input are seperate connectors, so yes this is possible.
Cat

Audigy 2 ZS - Microphone volume too low (using front case pan

Hi,
I've searched the forums for my particular problem and was unable to find a solution
I'm hoping someone here can guide me.
My microphone volume is extremely low whenever i plug it into the front jack of my case. Now if i were to plug it in directly at the back on the soundcard the volume is just fine.
I've checked my settings in the control panel, my mic is selected, the +20db boost is on. I've re-checked those settings both times ( while plugged in the back and in the front panel )
For the life of me, i cant figure out why the input volume just drops when i plug it in the front.
Any one have any ideas?
*note: i've checked settings in creative surround mixer and they are proper, the mic is selected and boost is enabled. I read somewhere about a line2/mic2 ? i do not see this option anywhere (in surround mixer or control panel sound options)
Any help is appreciated

im sorry that i cant help you, but how have you connected your case mic/headphone jacks? i thought this is barely possible on creative cards.. or do you have that creative bay-thing?
edit: ah sry i thought you have x-fi..Message Edited by zenu on 2-30-2005 2:24 AM

About Audigy NX and Microphone

I just want to know if the Sound Blaster Audigy NX accepts a micphone which needs 48v phantom power.
Thanks

jackczl wrote:
I just want to know if the Sound Blaster Audigy NX accepts a micphone which needs 48v phantom power.
Thanks
By the specs there is no 48V phantom power feed on that device --> you need a separate mic-pre w/ phantom power to get your mic working.
Here are some low priced USB devices w/ 48V phantom power onboard:
Alesis IO2 (from ~120US$ -->) - http://www.zzounds.com/item--ALEIO2
M-Audio MobilePre USB (~145US$) -
http://www.musiciansfriend.com/product/Recording/Computer/Hardware?sku=701368
Tapco by Mackie LinkUSB (~150US$) - http://www.zzounds.com/item--TAPLINKUSB
Behringer BCA2000 (~180US$) - http://www.zzounds.com/item--BEHBCA2000
jutapa

Audigy SB0570 And Modem - Prob

Hello, I am from Serbia and I don't speak English language very good. I was buy sound card Audigy SE SB0570 and when I listening music or working in audio programs and surfing on the Internet my computer is not functioning good. And only is restarting without warning... I am download new drivers from Creative site and when I install drivers problem is not fixed...
Please, help me... I have U.S. Robotics modem.
This problem...
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=62875#M62 875

Ban me and see if I care. I just think that people should know that the people at creative Labs have products that advertise being compatible with all windows oses and it is just not true.
banning me for telling the truth is confirmation of the fact.
I have heard that the truth hurts and I guess in this case it is true.
I have recieved no help and from reading other users posts I am not the only one.So go ahead it it nothing to me.
Have a nice day

Daniel_k we need microphone effects in windows 7 please

Hi please we need new driver support EAX Console & Microphone like Concert Hall effects in windows 7
Karaoke_feature1.jpg
my sound Card is creative Audigy SE SB0570
please if u can just add EAX Console & karaoke .
i try driver SB Audigy Series recompiled Install u made Unofficial When I try to install a window installation says that the card is not supported
i just want EAX console & karaoke & mixer to set what u hear .... please please i wait u

Heya
Im not 100% sure how Daniel is supposed to help you with this.
If he is an employee at Creative it mite be out of his control to add EAX Presets back into the creative control panel.
But speaking of which. I recently upgraded from my X-Fi Xtreme Gamer to a Z and I am extremely annoied that Creative decided to remove EAX presets like Jazz Club etc I really like the EQ but it would be better to have both and be able to use both at the same time.
I am still looking for alteritive software that will allow me to pick or set a effect that will give me the live sound for my music like Jazz Club
If these features your asking for where once there, use the last driver you had that had these features available
Uninstall your drivers this way to unsure that they are completely gone.
DOWNLOAD EVERYTHING FROM CREATIVE THAT YOU MAY NEED FOR YOUR SOUND CARD BEFORE UNINSTALLING, E.G WAVESTUDIO ETC
Close any programs that can make sound, even steam. (A message from a friend will play a unwanted sound when uninstalling the driver, part of the driver component will then be in use and may not be able to be removed) This is a Common cause of errors. Thats why it tells you to ensure every program is closed before installing and uninstalling.
Open Control Panel, Then At the top where its says View By click the small arrow pointing down on the right side of "View By" and select small icons, Then select Programs and Features,
Remove Everything that says Creative starting with Creative Control Panel,
Before Restarting your Pc
Open Control Panel, Then Select Device Manager,
In Device Manager click the arrow pointing right on the left of "Sound Video and Game Controllers"
Then right click your Creative Sound card if its still there after uninstalling everything from the creative uninstaller.
If its still there Right click your sound card and select Uninstall. When the window pops up "TICK" the check box saying "Delete All The Software For This Device" "DO NOT PERFORM THIS STEP FIRST!!!!!!!!!!!!!!!!"
Restart the computer and install the Original latest driver that had the funcions you desire.
I haven't proof read this to check for spelling mistakes so sorry if there is any lol

Microphone Volume on MSI x48c Platinum

I purchased a logitech 600 analog microphone and tried plugging it into both my rear mic jack and the case mic jack which is wired to the HD audio header on the x48c.
The mic is instantly recognized correctly by the Realtec audio manager and I have the latest drivers installed for the board off of the MSI download page...
However I cannot hear normal speech through it... the sound input is so weak.... I am pretty sure the mic is working fine... Only get a weak voice if mic is next to your mouth and you talk really really loud.
Has anyone else had this problem on this board...are there some hidden settings that need to be changed. I set the input volume to max in windows and it was not on mute so I checked all the obvious things.
Any ideas?

Could be a microphone impedance mismatch. I would test the mic in another PC to compare the results and also test another mic on your PC to see if there is a difference. Recheck/Reconnect the HD Audio connector plug. Test also with the non-HD Audio connector to see if there is a difference.

W520 Owners: Compatible Splitter for combo Headphone/ Microphone Port

The w520 has a combo Headphone/ Microphone Port. You can use either a headphone or a microphone but NOT both UNLESS you have a ...
1. Headset with special 3 ring jack such as
      a. ThinkPad In-Ear Headphones (#57Y4488)
      b. 3.5mm TRRS Plug type Headphones for Smartphones (e.g. iphones, etc.) -- so you use the same headphone/mic you use for your cellphones (but lesser sound quality)
2. Splitter - so you can you use your own microphone and your own headphone/ stereo speaker (for better sound quality)
This solution was found here...
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/Where-is-the-Stereo-out-on-the-W520/ta-p/47306...
But a list of Compatible Splitters was not listed...
The aim of this thread is to verify and list compatible Splitter for W520 combo Headphone/ Microphone Port
The specs of the splitter are as follows: (Kindly verify if correct)
3.5mm (1/8") TRRS male plug (aka Smartphone plug) TO
3.5mm TRS Audio-Out Jack/ female plug AND 3.5mm Microphone-In Jack/ female plug
I browse online and found possible splitters. (In no particular order)
1. Sound Professionals Part# - SP-SMARTPHONE-CABLE
http://www.soundprofessionals.com/cgi-bin/gold/item/SP-SMARTPHONE-CABLE
--it was mentioned in the details tab that it is compatible with " Lenovo T410, T410s, T510, X, L & Edge computers"
so it is possible that W520 is compatible if the other Lenovo have the same combo port
- nickel contacts
2. Headsetbuddy Gold PC Computer Headset to 3.5mm Smartphone Adapter (Part# 01-PC35-PH35G )
http://www.theheadsetbuddy.com/gold-pc-computer-headset-to-3-5mm-smartphone-adapter/
- it was mentioned "Convert two 3.5mm plugs to single smartphone 3.5mm headset plug (TRRS) with mic and audio"
   so it fits the specs but I am not sure if it was tested for W520...
- gold contacts.
3. Headsetbuddy Gold PC Headset to 3.5mm Smartphone Adapter (Part# PC35-PH35G )
http://www.theheadsetbuddy.com/gold-pc-computer-headset-to-3-5mm-smartphone-adapter-1/
- same description as above but different part#. I am not sure if this is the same product or just a typo error on their website.
-gold contacts
4. Headsetbuddy PC Computer Headset to 3.5mm Smartphone Adapter (Part#01-PC35-PH35 )
http://www.theheadsetbuddy.com/pc-computer-headset-to-3-5mm-smartphone-adapter/
- - it was mentioned "Convert two 3.5mm plugs to single smartphone 3.5mm headset plug (TRRS) with mic and audio"
   so it fits the specs but I am not sure if it was tested for W520...
- nickel contacts
5. KV Connection iPhone 1/8 inch microphone and headphone adapter - 3.5mm 4 conductor TRRS Male to 3.5mm TRS Jacks (Part# KM-IPHONE-2TRS)
http://www.kvconnection.com/product-p/km-iphone-2trs.htm
It was mentioned that they have "Premium shield coax a/v cable for EMI/RFI interference...DC blocking protection ... microphone impedance matching"
They say it will "work with most 3.5mm mono or stereo microphones except for for unpowered ECM (electret condenser mics). If your microphone is an ECM without batteries then this special version of the adapter KM-IPHONE-2TRS-ECM is the adapter you would need."
So I guess the the type of microphone will have an effect also on what splitter to get.
On this site..
http://www.wfu.edu/~yipcw/lenovo/2011/T420s/review/
It says that on using the Part# KM-IPHONE-2TRS, with a "mono mic [Sony F-V410 cardioid imp 600 Ω vocal] in , it reverts to internal microphone for some reason.) and headphone"
So there can be incompatible mics for any splitter you use... OR is the defective splitter or the computer setting that is wrong...???
-nickel contact
6. KV Connection iPhone 1/8 inch electret condenser microphone and headphone adapter - 3.5mm 4 conductor TRRS Male to 3.5mm TRS Jacks (Part#KM-IPHONE-2TRS-ECM)
http://www.kvconnection.com/product-p/km-iphone-2trs-ecm.htm
-On site it says "This adapter is specifically for unpowered ECM (electret condenser mics). If your microphone is an ECM with batteries then the standard adapter, KM-IPHONE-2TRS is the adapter you would need."
-nickel contacts
7. eVerbatim splitter
http://www.everbatim.net/store/index.php/hardware/microphones-audio/headphone-microphone-jack-splitt...
- It says "This adapter has been designed and tested to work with all current Lenovo ThinkPad computers with a combined audio (VOIP) jack running Windows 7. Some ThinkPads that have the combined jack and that are running XP do not work with the adapter, which is a software issue and not a defect of the adapter. "
-nickel contacts
8. Startech 3.5mm 4 Pin to 2x 3 Pin 3.5mm Headset Splitter Adapter - M/F (Part# MUYHSMFF)
http://www.startech.com/Cables/Audio-Video/Audio-Cables/35mm-4-Pin-to-2x-3-Pin-35mm-Headset-Splitter...
It says "allowing you to add a mono microphone input as well as a stereo output to your PC or Laptop, through a single 3.5mm audio port."
-nickel contacts
Kindly tell if you have used any of this on your laptop. And tell...
1. Compatible with your headphone? (what kind you use)
2. Compatible with your microphone? (what kind you use)
3. Any problems with sound?
I hope we can continue this thread to list the compatible splitters for the Lenovo Thinkpad W520... Please do add if you have seen other brands.
Thanks

Hi all
To be frank, some of the multimedia laptops, with SRS Premium Sound, etc. are having the same speakers as W510 / W520 and is very loud (AFAIK, Dell Inspiron N5110 have the same speakers as W520 and the placement is just below the palmrest like surround sound). Theoretically, it makes the sound less focus and soft, but it works well with that laptop.
The Mic and Speakers are powered by the amp / drivers. The hardware in fact is very good, the only problem with it is the driver / software not well written. Good Hardware + Bad Software = Bad Product.
If you want a better sound / mic, you could try my Dolby Home Theater v4 solutions, hopefully it could meet more than your expectations and solve your problems without any cost. In fact, Dolby GUI is more customizable than Conexant. Most of us would not think it's more complicated, as techies would prefers more options to have fun.
1. I don't even need a external mic, an internal mic does the job with this fix.
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/W520-bad-microphone-Usable/m-p/528497
2. Dolby makes the sound much better and louder with correct settings. If not, my post are not able to stay active till now, reaching 100+ posts.
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/W520-Sound-Enhancement-Thread/td-p/442761/pag...
Installation steps:
Simplifications of installing and optimizing Dolby Home Theater v4 threads. Message 77 and 78 + Attachment.
3. Get a USB solution only if you need multichannel audio, stereo / wave mix or studio grade quality, if you are just using for entertainment, etc. W520 with Dolby Home Theater v4 should be more than sufficient.
Cheers
Peter
=============================================
Does someone post helps you? Give them a kudos as a reward, as they will do better to improve
Mark it as solved if the solution works for you, so it could be reference for others in the future
Refunded Set: W510, 4876-A11
Current Set: W520, 4284-A99
Dolby Home Theater v4!:
http://forums.lenovo.com/t5/W-Series-ThinkPad-Laptops/W520-Sound-Enhancement-Thread/m-p/451401#M155...

Headphones and Win FM 5.31 no longer work after installing Audigy SE (Windows

[color="#ff0000"]I had the new Sound Blaster Audigy SE SB0570? installed in my computer. I have 2 front stereo speakers next to my computer monitor which are connected to the green output on the sound card and they work fine.
I get sound from Windows Media Player or either CD/DVD player. [color="#ff0000"]?[color="#ff0000"]But now my headphones, when plugged into the jacks in the front of my computer case?have no sound coming through. They will work from the same green output as my speakers use -- but that defeats the functionality and convenience of using headphones.[color="#ff0000"]?[color="#ff0000"]Is there another way to connect the headphones without having to share the same output as for the speakers ?[color="#ff0000"]I have tried using the other?2 outputs next to the green output -- but they don't work for the headphones.[color="#ff0000"]. ?[color="#ff0000"]I am having problems with my radio online. I am using winFM 5.3 and I can not get any sound though my speakers. I get sound from Windows Media Player or either CD/DVD player. [color="#ff0000"]?[color="#ff0000"]Help, please !!!![color="#ff0000"]?[color="#ff0000"]P.S.: when I installed the software cd, all went well except for this message:[color="#ff0000"]??"Windows Media Player 0"?? This version of Windows Media Technologies is incompatible with this version of windows. For more information, view the information at the Microsoft web site.[color="#ff0000"]??

Solved after reinstalling Win XP. Wasted too much time on trying other possible solutions.
Hope other people may learn something out of it.

Audigy SE SB0570 microphone impeda

Similar Messages

Maybe you are looking for