AUTH command is not enabled.
I have just fresh installed a new MTA, everything is fine but when telnet <own-ip> 25 and when I try to do auth login, I have got this error:
*AUTH command is not enabled.
I supposed the auth login is by default being enabled, may I know how to enable it?
Regards,
gthian
haw_9368 wrote:
I have just fresh installed a new MTA, everything is fine but when telnet <own-ip> 25 and when I try to do auth login, I have got this error:
*AUTH command is not enabled.
I supposed the auth login is by default being enabled, may I know how to enable it?SMTP authentication is only enabled if you have mustsaslserver or maysaslserver keyword on the channel which you are connecting to.
By default the tcp_intranet channel doesn't have this keyword. Try adding maysaslserver to the tcp_intranet channel, then run ./imsimta cnbuild;./imsimta restart.
When you telnet <own-ip> 25, type in, EHLO blah.com, you should see the following:
250-AUTH PLAIN LOGIN
250-AUTH=LOGIN
This means SMTP Auth is enabled.
Regards,
Shane.
Similar Messages
-
AUTH Command is not enabled, when try to enable webmail with smtp auth
Hi,
I'm trying to force all the webmail users to authenticate (smtp auth) when they send an email.
I already configure this:
local.service.http.smtpauthpassword = xxxxx
local.service.http.smtpauthuser = admin
and reload the http service. (the password is correct)
Then, enter to the webmail interface and tried to sent an email but when pressed "sent" the following message appears:
SMTP: Error 5.7.1 AUTH Command is not enabled.
Do I have to do something else? Any lead?
RegardsThanks Jay,
I know about the little use of the webmail authentication but it is something I need to do because in my configuration I have to differentiate between users who can send emails to internet and users who can not, and in order to do that, I need to authenticate all the users. So far is working if the user uses an email client.
For webmail I did not know that I have to add in the tcp_intranet channel definition the attribute: mustsaslserver. -
3640 - AAA/AUTHOR: config command authorization not enabled
Hello, I have a 3640 router with c3640-ik9o3sw6-mz.122-8.T.bin version but when I try to validate the username and password with a radius server, the debbug message is "AAA/AUTHOR: config command authorization not enabled" and I'm sure that the radius validates the user and the packet arrive to the router.
I've tried to update the IOS with c3640-ik9o3s-mz.122-46a.bin and I can validate but I cannot use "crypto isakmp client configuration group mygroup" to configure Easy VPN server.
I attach you the files with config and logs.
Thanks you in advance.Yep! I'm really running 12.1!
I'm receiving the message once i include "aaa authorization exec default group radius local if-authenticated" in the config.
Login is successful, however authorization does not allow me to go directly into enable mode. If I take the aaa authorization line out I can login to user mode and then use the enable password to move forward but that is not what I wish to achieve.
sh run | i aaa
aaa new-model
aaa authentication attempts login 5
aaa authentication banner ^C
aaa authentication fail-message ^C
aaa authentication login My-RADIUS group radius local
aaa accounting exec My-RADIUS start-stop group radius
aaa session-id common
Is there somewhere specific I was suppose to configure the aaa authorization enabled, because I'm not seeing it.
Let me know what other thoughts you may have.
Thanks
Nik -
Config command authorization not enabled
Can someone tell me why I'm getting this message. I'm beginning to think this has something to do with my device failing authorization.
Show version
Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.1(19)EW1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)Yep! I'm really running 12.1!
I'm receiving the message once i include "aaa authorization exec default group radius local if-authenticated" in the config.
Login is successful, however authorization does not allow me to go directly into enable mode. If I take the aaa authorization line out I can login to user mode and then use the enable password to move forward but that is not what I wish to achieve.
sh run | i aaa
aaa new-model
aaa authentication attempts login 5
aaa authentication banner ^C
aaa authentication fail-message ^C
aaa authentication login My-RADIUS group radius local
aaa accounting exec My-RADIUS start-stop group radius
aaa session-id common
Is there somewhere specific I was suppose to configure the aaa authorization enabled, because I'm not seeing it.
Let me know what other thoughts you may have.
Thanks
Nik -
DACP commands are not working on Ipv6 enabled Airplay ITune service on MAC book.
DACP commands are not working on Ipv6 enabled Airplay ITune service on MAC book.
As we have gone through the source code(Airplay
Audio POSIX receiver v190.9.p6) in dnssd_clientshim.c file and in API DNSServiceGetAddrInfoResponse has provided the implementation for ipv4 only.
The test setup to test the DACP over IPV6 is by disabling the IPV4
from MAC book and only enabling the Ipv6 .
We are not sure if the test procedure is correct, please clarify the same.Hi,
It is because of the license. In WS-C3750X-48P-L, you have a LANBASE license whereas in WS-C3750X-24P-S you have an IPSERVICES license.
FDR_SW#show version
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE5, RELEASE SOFTWARE (fc1)
License Level: lanbase
License Type: Permanent
Next reload license Level: lanbase
In a LANBASE license, ip routing and ip multicast commands are not supported.
Hope this helps.
Thanks,
Arun -
BitLocker not Enabled on HP ElitePad 1000 G2
I have an HP ElitePad 1000 G2 that I am using MDT to apply our 8.1 x64 Update image. This task sequence works fine on all other systems on which it has run. On the ElitePad, when the task sequence completes, BitLocker is not enabled.
Running manage-bde-status returns:
Disk volumes that can be protected with
BitLocker Drive Encryption:
Volume C: [OSDisk]
[OS Volume]
Size: 115.58 GB
BitLocker Version: 2.0
Conversion Status: Used Space Only Encrypted
Percentage Encrypted: 100.0%
Encryption Method: AES 128
Protection Status: Protection Off
Lock Status: Unlocked
Identification Field: Unknown
Key Protectors:
TPM
If I look in the BitLocker applet on the control panel, it says "OSDisk (C:) BitLocker is waiting for activation"
the ZTIBDE.log just stops at:
Attempting to intiate ProtectKeyWithNumericalP@ssword
<Message containing password has been suppressed>
A successful system shows:
Attempting to intiate ProtectKeyWithNumericalP@ssword
Success protecting Key with numerical p@ssword
If I click Turn on BitLocker in the control panel applet or run the following commands:
manage-bde -protectors -add c: -recoverypassword
manage-bde -on c: -recoverypassword
The recovery key protector is created and uploaded to AD and BitLocker shows as enabled.
Any ideas to why this is happening?after some more investigation, I found the following article
http://netecm.netree.ch/blog/Lists/Posts/Post.aspx?ID=80 and adding the registry key referenced in the article fixed the issue. -
Please i need a help, I try to recovery the password of One AP Aironet 1200 series (AIR-AP1231G-E-K9) but the bouton mode is not Enable, so can you help me ,
Note: i already try to press esc when the flash is loading but i no think is happen
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
ether_init
tftp_init
boot
button pressed for 15 seconds
process_config_image_recovery Failure
Mode-Button not enabled
Loading "flash:/c1200-k9w7-mx.123-8.JA2/c1200-k9w7-mx.123-8.JA2"...############################################################################button pressed for 15 seconds
process_config_image_recovery Failure
Mode-Button not enabled
Loading "flash:/c1200-k9w7-mx.123-8.JA2/c1200-k9w7-mx.123-
I see this message when i try the first option and for the second it's not possible because i have not the the password. -
I've written a powershell script to prep server for SCCM 2012 and the only annoyting thing I can't seem to get rid of is the yellow warning message that appears as a result of installing new Windows roles/features. The specific message is: "Warning:
Automatic updating is not enabled. To ensure that your newly-installed role or feature is automatically updated, turn on Windows Update."
Is there an "undocumented" silent switch that I can append to the "Install-WindowsFeature" command-let that suppresses this?
Thanks for any guidance anyone has found for this.
jclHi,
I'm not completely sure about this, but you could try setting the $WarningPreference variable to SilentlyContinue.
http://technet.microsoft.com/en-us/library/hh847796.aspx
Don't retire TechNet! -
(Don't give up yet - 12,950+ strong and growing) -
How to restoring controlfile when autobackup was not enabled from TAPE?
Database was dropped an year back and we need to restore the database
1)controlfile autobackup was not enabled
2)backups are in tape
3)no catalog db used
4)DBID is known.
we can request to load tapes that are holding backups from 1 week prior of db drop date
we can not use "restore controlfile from autobackup" as autobackup was not enabled. So how can we restore the controlfile?user8860934 wrote:
Database was dropped an year back and we need to restore the database
1)controlfile autobackup was not enabled
2)backups are in tape
3)no catalog db used
4)DBID is known.
we can request to load tapes that are holding backups from 1 week prior of db drop date
we can not use "restore controlfile from autobackup" as autobackup was not enabled. So how can we restore the controlfile?Do you have full backup... did include current controlfile mentioned in the script?
1)catalog those backupsets
2)check the backup summary for controlfiles & datafiles, SPFILE(optional)
3) if exist then you can restore using DBID or catalog start with commands.
Thanks -
trying to install Lion. says this disk is not enabled (journaled) - but when I look at the drive it actually is os extended journaled - Stuck! Have tried repair disk permissions and still no luck - any thoughts? Have spent two weeks trying to get apple support and itunes to help me get lion after a hard drive fail and now they are closed and I really just want to get moving!
Are you installing OS X Lion over an existing installation of Snow Leopard, or are you reinstalling?
First be sure you have everything on your system backed up. Then reboot with the Command-R keys held to get to the OS X Lion recovery volume. In here, select Disk Utility and use the First Aid tab in here to run a verification on your boot drive. If there are any errors, fix them and then try the installation again.
The next step would be to format the drive, so with your backup secured, use Disk Utility's Erase tab to re-format the drive to Mac OS X Extended (journaled), and then quit Disk Utilty and attempt the installation again. -
Port security not enabling/ sticky/static
ok i tried both commands. port security is not enabling (shows disabled in output) its cisco ip phone connected to port.
static and sticky
H(config-if)#$port-security mac-address 001E.13AF.893C
H(config-if)#no shut
H(config-if)#end
H#show por
H#show port-security in
H#show port-security interface g2/0/38
Port Security : Disabled
Port Status : Secure-down
Violation Mode : Shutdown
Aging Time : 0 mins
Aging Type : Absolute
SecureStatic Address Aging : Disabled
Maximum MAC Addresses : 1
Total MAC Addresses : 1
Configured MAC Addresses : 1
Sticky MAC Addresses : 0
Last Source Address:Vlan : 0000.0000.0000:0
Security Violation Count : 0Did you enable the port by adding :
switcport port-security
what is the output of "sh run int gi2/0/38"
HTH -
Hi,
I have a problem in create user in TimesTen.
When I write command:
create user testuser identified by 'test';
command line give me an error:
15007: Access control not enabled
The command failed.
My ttVersion is:
TimesTen Release 7.0.3.0.0 (32 bit NT) (tt70_32:17000) 2007-09-19T16:04:16Z
Instance admin: dominik
Instance home directory: C:\TimesTen\tt70_32
Daemon home directory: C:\TimesTen\tt70_32\srv\info
My OS is Windwos 2000.
I found advice on this forum but it doesn't work. I tell about doing this command:
ttDaemonAdmin -stop
ttuser -init c:\TimesTen\tt70_32\srv\info\ttpasswd -admin dominik
ttDaemonAdmin -start
Can anyone have idea how to make access control enable??
DominikFirst of all, I want to thank you Chris for so many suggestions :)
So I answer to your sentences:
You need to uninstall and re-install TimesTen in order to enable the access control facility.I think that this solution won't help.. I really remember that I check Access Control during the instalation, because I install TimesTen first time and I use viewlet from oracle site for help!!
Do you have a supported version of the Oracle client installed? Yes I'm sure that both of the system have supported Oracle version (Oracle 10g)
Is the environment setup properly for the Oracle client? Did the user you were logged in as when you installed TimesTen have a valid Oracle client environment. In 99.99% of cases, this issue is because the Oracle client is not installed or the TimesTen service does not have a valid Oracle client environment.As I said, I install TimesTen with viewlet, so I think that properly setup environment
Actually, you van enable access control without uninstalling and re-installing. You need to run the command: ttmodinstall -enableaccesscontolI try this command on Windows and that is the result:
Would you like to enable access control for this instance? [ no ] yes
NOTE: The daemon must be stopped before enabling access control.
Would you like to stop the daemon? [ yes ]
Retrying ...
Retrying ...
Retrying ... <- and process doesn't retry :/
Even if I start this process on Administration Panel -> Services and write command ttVersion in command line, still Access Control is not shown :/
I try this command on Linux too..
And this is the result:
Would you like to enable access control for this instance? [ no ] yes
NOTE: The daemon must be stopped before enabling access control.
Would you like to stop the daemon? [ yes ]
Enabling access control ...
Patching successful ...
Restarting the daemon ...
Warning: library libclntsh.so does not exist at /oracle/10g/lib or /oracle/10g/lib32. Check ORACLE_HOME for proper operation of Cache Connect.
TimesTen Daemon startup OK.
Access control is now enabled for this TimesTen instance.
It look nice, but when I try co connect:
connect "dsn=ttdemo;oraclepwd=myuser";
It not work :/
Can anyone help me now?? Chris?? -
Map is not enabled in your country (which is US)
I installed the lightroom in US, but it says "map is not enabled in your country".
Language of Lr is Chinese, but it should not be the problem since the message still exists after I re-installed it in English.
Things I tried:
re-install Lr
re-install Adobe Flash Player
Update Windows
Use VPN
Close firewall
All didn't work.
When I try to switch map style, the program do successfully connect to Google server. I can see lightroom.exe connected from IP 169.231.36.247:52674[My school in Santa Barbara CA] to 74.125.25.95:443[Google's server in Santa Clara CA]. I tried to use ping command on this IP, everything is fine.
So WHY it keep telling me map is not enabled in my country?! (Of course in "my country" Google disabled map because I'm from China but I'm not in China now!)
The only reason I can come up with is that "Adobe can somehow find out where the computer is bought or where the people sitting behind the computer is from and disable the map". I believe Adobe is not likely to do things like that.
If people from Adobe can see this discussion, please tell me how Lightroom detect the country. I will do anything I can do to enable that map.Thank you for your suggestion but I can't find that " Lightroom Registration" button.
-
I am running a 2106 controller with 1242 AP,
Had them on a POE injector on the same switch worked fine, mounted them in the ceiling now the radio will not enable."error in enabling admin status". any ideas?Hi Paul,
I think you might be running into this issue because the 1242 AP supports the Intelligent Power Management feature (which I didn't even know existed until recently). Have a look at the following.
Power Issue with the AP
When an AP uses a power injector as the power source, in some cases, the AP displays this error message:
CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC inline
This message indicates that the AP is in low-power mode with all radios disabled and detects a Cisco switch that is unable to supply sufficient power to the AP. Even though the power injector, which can provide sufficient power, is connected with the AP, the AP still displays a LOW POWER error message and disables the radios. Therefore, the AP remains in low-power mode.
One possible reason for this issue might be that the AP supports the Intelligent Power Management feature. The Intelligent Power Management feature uses Cisco Discovery Protocol (CDP) to allow powered devices, such as an AP, to negotiate with a Cisco switch for sufficient power. The AP supports the Intelligent Power Management feature. As a result of the power negotiations, the AP either enters full-power mode or remains in low-power mode with the radios disabled.
In this case, the AP might be connected to a switch which cannot provide the necessary power to the AP. Therefore, even though the power injector is connected to the AP that uses this Intelligent Power management feature, it gives priority to the CDP information to identify whether or not the switch can provide the power. Once the AP knows, via CDP message, that the switch does not provide sufficient power, it disables the radios and remains in low-power mode.
The workaround to this issue is to tell the AP to ignore the CDP information for power. You can perform this by telnetting into the APs. Issue these commands to enable the APs to use the power injector:
power inline negotiation prestandard source
power inline negotiation injector H.H.H
The power inline negotiation command configures the Cisco Aironet 1130AG or 1240AG Series AP to operate with a later version of switch software that does not support Cisco Intelligent Power Management power negotiations.
The prestandard source portion of the command specifies that the Cisco switch runs a later version of software that does not support Intelligent Power Management negotiations, but is able to supply sufficient power to the AP.
The injector H.H.H portion of the command specifies that a power injector supplies power to the AP, and that the AP connects to a new switch port with the indicated MAC address (H.H.H). Enter the MAC address (in xxxx.xxxx.xxxx hexadecimal format) of the new switch port where the power injector is connected.
Note: This command should only be used when you move an AP and power injector to a different switch port.
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps441/products_tech_note09186a00800a86d7.shtml#new3
Hope this helps!
Rob -
Hi,
We're running SCCM 2012 R2 CU2. Our boot images have Enable command support enabled. I am able to use F8 to get a command window at the Welcome to the Task Sequence Wizard. After the first restart, F8 and Shift-F10 have no effect.
I have a computer that keeps getting hung somewhere in the task sequence but I have no way to get to the logs. If I force power off and power on again, the computer is stuck in the same place again with no command window support. I tried booting to WinPE
and use CMTrace but it cannot access the OS drive from the "in-progress" deployment which I believe could be due to drive encryption.
How do I get the command prompt (F8) to work? I have done some searching and haven't found a solid answer yet.
Thanks,
RobYou've confirmed that F8 works to open a command prompt in the initial WinPE, but not after the next part, which is an indication that the task sequence switches to using a boot image that doesn't have command prompt enabled. Although you may have already
done this, confirm that the boot image used by the task sequence does indeed have command prompt support enabled.
If all of your boot images do have command prompt support enabled (which, you should be using only one if at all possible), try disabling and re-enabling the support, and confirm that the process finishes correctly.
F8 will work throughout the entire task sequence, if enabled properly.
Maybe you are looking for
-
Assigning a value to a number field through a button
11gxe , apex 4.x , hi all , i am trying to assign value to a number field through a button , i created a button , then a dynamic action for this button , when it is clicked , the dynamic action is based on Pl\Sql code , and the code is begin :p2_assi
-
I haven't even had a job before and it's asking me what my favorite job was and what my worst was... But I have no clue what the answers are
-
Hi all, Need to figure out whether we can change or edit a PERSONNEL SUBAREA. My client is planning to move from 4.6c HR to 4.7 HR. during this change they need to change some of the personnel subarea (i think just rename).So they need to do
-
Rebuild RAC phsical standby with RMAN
Hi all, Can anyone give any advice as to rebuilding an ACTIVATED RAC physical standby using RMAN? We have been able to revert the db with flashback but I need to know the rebuild method. Is there any extra steps with the OCR? I am guessing the steps
-
Respected sir, I want to know about how to delete the key based on the key and data value. Eg:- Key = 100 data = aneesh Key = 100 data = nobu Key = 200 data = vava. i want to delete key = 100 and data = aneesh. please give me the answer of the above.