AutoQoS Marking at CE done. PE router?
Hi there,
I've implemented an AutoQoS at managed CE router which is running MPLS VPN. At the PE router, I need to match the mpls experimental bits, kind of confuse to do at PE router.
BTW, is there a such for AutoQoS for PE router, particularly on MPLS VPN?
Thanks in advance.
Below is the config at CE:
class-map match-any AutoQoS-VoIP-Remark
match ip dscp ef
match ip dscp cs3
match ip dscp af31
class-map match-any AutoQoS-VoIP-Control-UnTrust
match access-group name AutoQoS-VoIP-Control
class-map match-any AutoQoS-VoIP-RTP-UnTrust
match protocol rtp audio
match access-group name AutoQoS-VoIP-RTCP
policy-map AutoQoS-Policy-UnTrust
class AutoQoS-VoIP-RTP-UnTrust
priority percent 70
set dscp ef
class AutoQoS-VoIP-Control-UnTrust
bandwidth percent 5
set dscp af31
class AutoQoS-VoIP-Remark
set dscp default
class class-default
fair-queue
ip access-list extended AutoQoS-VoIP-Control
permit tcp any any eq 1720
permit tcp any any range 11000 11999
permit udp any any eq 2427
permit tcp any any eq 2428
permit tcp any any range 2000 2002
permit udp any any eq 1719
permit udp any any eq 5060
ip access-list extended AutoQoS-VoIP-RTCP
permit udp any any range 16384 32767
Hi Maher,
At this point in time, Cisco only supports AutoQoS for VoIP and for Enterprises. I don't think there are too many carriers out there who would be interested in such a feature since they would want to customise QOS parameters to their network and not use a boiler-plate automatiically-generated configuration.
Paresh
Similar Messages
-
I have just deleted Macintosh HD. Now I have reset my computer and there is just a flashing folder with a question mark. I don't know what to do, I'm really worried about this so please May you get back to me as soon as possible?
Why did you delete the hard drive? If you delete the contents of the Macintosh HD you have no system to boot into. That's what the flashing folder/? means. What system were you using before deleting everyting.
You're going to have to install a system on the HD before you can boot.
OT -
How can I mark event as "done" so that I see this at one glance?
how can I mark an event on ical as "done" so that I see this at one glance? In outlook this was possible, there was a white line on the left once I had marked the event as "done".
Greetings,
If you are new iCal user read this: http://support.apple.com/kb/HT2513
Events are more along the lines of a...well...event "Appointment with Dr. Smith"..."Travel to Mexico"..."Jon's Birthday".
What you are describing is what I would call a task. iCal offers "To Dos" for that purpose which include a check box for completion.
Cheers! -
"Film Safe" and "Mark repeated frames" don't seem to work?
Hi guys!
I'm new to this forum and new to FCP Pro - though I'm not at all new to non-linear editing (Media100, Avid, etc.).
A friend of mine is editing a feature film on a brand new G5 (dual) using a newly installed Final Cut Studio. Everything is working just fine except the marking of repeated frames in the sequence. I did my best to find the answers in the pile of books that came with the s/w, then tried to consult with editors around here - to no effect, alas! FCP is not very popular in Bulgaria (it's really a shame!) and the other two film projects that make use of it also have similar problems.
Can any of you, guys, help?
The problem in more detail:
FCP Pro 5 does not mark "on the fly" the repeated frames in a sequence. To be more precise, sometimes it does and sometimes it doesn't - and in a single sequence. If that wasn't enough, I'm not able to make FCP mark those dreaded "couple of frames" needed for negative cutting (inless the corresponding dupes are produced, that is!).
I have really tried to solve the problem on my own using the books and consulting people and have done a lot of testing and trying, so please bear in mind:
- "Mark repeated frames" is checked in "Preferences"
- I am using one and the same project and sequence for these tests
- the computer is G5, dual processor, 1 month old
- the software is Final Cut Studio, latest version
- I'm a bit pressed for time, as the editing must be completed by the end of Jan.'06
I will greatly appreciate your help!
G5 Mac OS X (10.4.4)GUYS, I NEED HELP !
ANYONE? -
How do I get other team members to review and mark footage who don't have CS6
Hi
I'm using Premier Pro CS6 and and need to get sign off for 4-6 videos a day.
In older versions of Premier Pro I used to be able to export a PDF with video embedded, that worked great.
I've now found out in CS5 that CS Review replaces this functionality.
Is there a simple way other than a pen a paper or spreadsheet that I can get collegues to review footage and feed back information back to me.
Rgds
LeeCS Review for Premiere Pro was a feature in CS5, but following customer feedback it was removed and is no longer operational. PDF-based reviews in Acrobat Pro are the functional replacement within CS6, but they cannot be directly-created from within Premiere Pro or Adobe Media Encoder.
You can certainly place a video into a PDF file using Acrobat Pro - but it has to be in a format supported by Flash Player (FLV, F4V or H.264).
The workflow for CS6 is therefore:
Export media from Premiere Pro using H.264 or Flash Video presets at suitably-low quality.
Drag-drop the saved video file into Acrobat Pro
Comment Panel > Review > "Send for Shared Review"
It's advised to review using the automatic Adobe Online Services repository so that people don't have to re-upload the PDF file itself.
[PS - there's a video tutorial for Acrobat X here - the UI is now a little different but the principles are the same ] -
EOS 5D Mark III ratings don't transfer to LR 4.1
I can't see that ratings transfer to Adobe Lightroom 4.1, but they do transfer to Canon DPP just fine. I think I've looked through all EXIF and IPTC fields and can't find the ratings data anywhere in LR. Where is it supposed to show in Lightroom?
My workflow:
- Rate RAW images in EOS 5D Mark III on compact flash
- Remove compact flash form 5D and plug in to USB card reader.
- Import in Lightroom 4.1 using LR's import function (on Windows Vista 32-bit SP3)
I can't see any ratings in LR, but when looking at the images in DPP and in Windows Explorer (with latest Canon RAW codec) the ratings are there. As I can see the ratings in DPP and Explorer it feels like a setting in Lightroom isn't right.
Any help on this issue would be great.
Donald
www.dlinderyd.comThat might be true, but I've read on numerous sites (e.g. http://www.wired.com/reviews/2012/06/canon-eos-5d-mark-iii/, http://mansurovs.com/canon-5d-mark-iii-review, http://feedback.photoshop.com/photoshop_family/topics/star_ratings_set_in_5d_mark_iii_not_ transferred_to_lightroom_v4) that in-camera ratings are transferred to LR. It just doens't seem to work for me.
Any help on this issue is very welcome.
Donald
www.dlinderyd.com -
Mark Workflow Done - Business Operation Status
Hi,
In my workflow, suppose i have a Task T1 performing some business operation and i have a Event listener, which on receiving an XML event performs the action 'Mark Workflow as Done'.
At this instance what would happen to the business Operation in T1, which might be still updating the database. That Transaction is committed or Rolledback.Hi Mark,
Well I assumed that you have confirmations integration active !! But I guess not because you say that the status is not integrated always.
What you need to do:
1) I assume you have SP05 or later.
2) Implement the user exit: CONFPM05. In the implementation of this exit you need to call FM: /MRSS/RSG_PM_ORDER_CONFIRM
3) Go to customizing: Basic Settings --> Assign ERP Objects --> Status
-- Here, define an abstract status (MRS Status) for confirmed and partially confirmed
-- map it to R3 status CNF and PCNF.
After this, whenever you enter confirmation for PM order from transaction IW41, the status will be integrated.
Now you can use the MRS statuses defined in step 3 to configure the colors.
Implementing the user exit CONFPM05 might require some technical input. But it is easy. Just a few double clicks and copy paste.
Contact an ABAP developer for the same.
This should solve your issue.
Regards
Varun -
I keep getting the little blue box with the question mark
Hi
I have 10.6.7 system software and my safari is 5.0.4
I have called apple twice with this problem already but nothing has helped except for short times.
I have reset safari about one dozen times and when I do I reset the top 7 items and I've emptied the cache in addition just in case. I've also taken my safari preference plist out of my library and trashed it.
And I've run disk utilities many times and restarted my computer. Each thing I do will solve the problem for a short time, even up to a day or more (or less) but then it comes back. For instance on Facebook maybe 1/8th of the thumbnail images have the little blue boxes with the question marks but most don't. I can't figure it out. Sometimes even the iPAD safari gets them too but my firefox doesn't show them and neither does Safari on my eMac.
Yesterday the question marks even showed up in ONE mailing on all 3 computers with the question marks in the blue boxes (meaning my iMac, my eMac and my iPad) but then it just all resolved after a few hours. This does sound like possibly a server problem except today it's happening (in Safari again) only on this iMac in Safari (not firefox) and not on the other two devices.
One more thing, since they changed my radio on the roof for my wireless internet, the 5.8 phone cuts out the internet when I use it. The problem has gotten worse since they changed the radio to the same frequency as the phone, it's a much faster service than the 2.4 radio. I don't know if this is related or not.
Thank you,
Martha<Contact your ISP.
Is it possible, Carolyn, that this would mainly and almost always be only affecting the iMac and Safari in the iMac if it were a server issue? Right now Safari has more blue boxes with question marks than ever and the eMac and iPad have none. Firefox on the iMac has none also.
I should try a direct connection and by pass the router and see if that makes a difference.
I will contact them tomorrow but I want to get clear in my head first all the facts and possibilities.
Thanks!
Martha -
(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!
=================
i have a cisco router 7200 NPEG2 processor , worked as LNS for PPPOVPDN circuits (Router for ADSL clients)
i have "high ip input on my processor" and there is alot of differnce on my router between operations done by cef and operations done by router cpu
as an example , lets make show cpu process sorted
CPU utilization for five seconds: 67%/54%; one minute: 67%; five minutes: 68%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 10837056 46891299 231 6.31% 6.04% 6.32% 0 IP Input
122 4081972 38214106 106 2.47% 2.36% 2.46% 0 L2X Data Daemon
270 467844 2089101 223 0.79% 0.78% 0.79% 0 PPP Events
275 1862224 2102444 885 0.71% 0.73% 0.71% 0 SNMP ENGINE
112 627104 93588 6700 0.39% 0.36% 0.37% 0 CEF: IPv4 proces
273 854004 4207368 202 0.31% 0.26% 0.24% 0 IP SNMP
52 453256 12321 36787 0.31% 0.31% 0.31% 0 Compute load avg
258 295540 701580 421 0.23% 0.17% 0.15% 0 RADIUS
142 45792 14107303 3 0.23% 0.21% 0.21% 0 HQF Shaper Backg
78 86532 166975 518 0.23% 0.17% 0.13% 0 ACCT Periodic Pr
260 483164 248673 1942 0.23% 0.19% 0.24% 0 L2TP mgmt daemon
272 63980 1073491 59 0.15% 0.16% 0.15% 0 IPHC Admin
77 111560 184597 604 0.15% 0.08% 0.06% 0 AAA ACCT Proc
261 330572 217566 1519 0.15% 0.12% 0.15% 0 L2TUN Applicatio
274 450584 2102164 214 0.15% 0.15% 0.15% 0 PDU DISPATCHER
16 152352 1081873 140 0.07% 0.08% 0.19% 0 EnvMon
279 229040 27298 8390 0.07% 0.10% 0.11% 0 VTEMPLATE Backgr
40 23704 53593 442 0.07% 0.03% 0.02% 0 Net Background
95 4512 55604 81 0.07% 0.00% 0.00% 0 PPP Hooks
109 6844 62029 110 0.07% 0.00% 0.00% 0 IP Background
269 21384 1931910 11 0.07% 0.06% 0.07% 0 PPP manager
271 116 60672 1 0.07% 0.00% 0.00% 0 Multilink PPP
23 98400 321 306542 0.00% 0.07% 0.03% 0 AAA high-capacit
=====================
as we see above , we have high "IP Input" about differnece in cpu =67-54=13 % , which is high value process in software .
i follwed the article here :
http://www.cisco.com/c/en/us/support/docs/routers/7500-series-routers/41160-highcpu-ip-input.html
i check and found that my router is fine ,
no arp calls.
no routing loops.
no flapping links.
i checked that my router has cef enabled and no enormous routing protocol updates
i found that i have big differnce between hardware & software process on the router which is 13 %
but when the traffic is more and more , the cpu reach reach 93 % and begin to have drops.
i just want to ask , how can i debug the operations that are done on the cpu processor of the router ???
i mean that if i know that traffic , i can estimate and know the problem that increasing my cpu !!!
another question :
how to debug the packest that has a ttl exceeded 50 or ttl exceeded 100 ?????
i dont wan tto make debug ip packed , because i have a huge traffic and it will let my router hanged due to large debug !!
===============
righ now i will post my router config and some verification:
drvirus#sh running-config
Building configuration...
Current configuration : 12291 bytes
upgrade fpd auto
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service dhcp
hostname drvirus
boot-start-marker
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T7.bin
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T8.bin
boot-end-marker
logging message-counter syslog
aaa new-model
aaa group server radius radiusservers
server-private 10..f.f.f auth-port 1812 acct-port 1813 key 7 weifuhjkefkjdbhfjkasbfjka
aaa authentication login adminstaff local
aaa authentication login sdm_vpn_xauth_ml_1 group radius
aaa authentication login ahmad local
aaa authentication ppp vpdn group radiusservers local
aaa authentication ppp drvirus local
aaa authentication ppp vpdn1 local group radiusservers
aaa authentication ppp ddd none
aaa authentication ppp dddd none
aaa authentication ppp anyok none
aaa authorization network default group radius local
aaa authorization network vpdn group radiusservers local
aaa authorization network sdm_vpn_group_ml_1 local
aaa authorization network drvirus local
aaa authorization network vpdn1 local group radiusservers
aaa authorization network ddd none
aaa authorization network anyok none
aaa accounting delay-start
aaa accounting update newinfo periodic 10
aaa accounting network vpdn
action-type start-stop
broadcast
group radiusservers
aaa server radius dynamic-author
client xxxxxxxx
client 10.xxxxxx
client 10.xxxxxxxxx
server-key 7 dihcbsdjkbvcsdhmbvhsdbvsdhmbvsd
auth-type any
aaa session-id common
clock timezone GMT+3 3
no ip subnet-zero
no ip source-route
no ip gratuitous-arps
ip cef
no ip bootp server
ip domain name drvirus
ip name-server x.x.x.x.x
ip name-server 8.8.8.8
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
ipv6 dhcp pool vvv
prefix-delegation pool version6
address prefix 3333::/64
dns-server 4444::1
multilink bundle-name authenticated
vpdn enable
vpdn logging
vpdn logging local
vpdn history failure table-size 50
vpdn-group eeeeeeeeeeee
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname qqqqqq
local name rrrrrrr
lcp renegotiation on-mismatch
l2tp tunnel password 7ekfhjjeklfnlenfl
l2tp tunnel timeout no-session 60
ip mtu adjust
username drvirus@!34`!512&$8#$232!^@^FGsdGD privilege 0 password 7 000sdkjhvsdkjvnah94313085g2355091407458E32425D
interface Loopback1
ip address ttttttt 255.255.255.255
interface GigabitEthernet0/1
description ttttttt
ip address 10.60.60.2 255.255.255.0 secondary
ip address 10.200.200.200 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/1.4
encapsulation dot1Q 4
ip address ttttttttt 255.255.255.224
interface GigabitEthernet0/1.14
encapsulation dot1Q 14
ip address 192.168.50.3 255.255.255.0
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
ip address 10.160.150.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description rrrrrrr
ip address xxxxxxx 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
interface Virtual-Template1
ip unnumbered Loopback1
ip tcp adjust-mss 1412
no logging event link-status
peer default ip address pool xxxxx xxxxxx
ppp mtu adaptive
ppp authentication pap vpdn1
ppp authorization vpdn1
ppp accounting vpdn
router eigrp 2
redistribute connected metric 1 2 1 2 1
passive-interface default
no passive-interface GigabitEthernet0/1
network 10.200.200.200 0.0.0.0
no auto-summary
eigrp router-id 2.2.2.2
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.200.200.2
ip route dddddddddd 255.255.255.0 fffffff
ip route ddddddddd 255.255.255.0 ffffff
no ip http server
no ip http secure-server
ip radius source-interface GigabitEthernet0/2
radius-server attribute nas-port format d
radius-server configure-nas
radius-server host ddddddddddd auth-port 1812 acct-port 1813 key 7 dddddddddd
radius-server retransmit 0
radius-server key 7 dddddddddddddddddd
radius-server vsa send cisco-nas-port
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
drvirus#sh ip traffic
IP statistics:
Rcvd: 92454889 total, 5908020 local destination
0 format errors, 94 checksum errors, 3789577 bad hop count
0 unknown protocol, 23360 not a gateway
0 security failures, 0 bad options, 3730347 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 3730347 alert, 0 cipso, 0 ump
0 other
Frags: 1409002 reassembled, 485 timeouts, 0 couldn't reassemble
4542214 fragmented, 9089659 fragments, 2659413 couldn't fragment
Bcast: 6024 received, 0 sent
Mcast: 56503 received, 31033 sent
Sent: 15839581 generated, 2407203241 forwarded
Drop: 23 encapsulation failed, 0 unresolved, 0 no adjacency
0 no route, 0 unicast RPF, 0 forced drop
0 options denied
Drop: 0 packets with source IP address zero
Drop: 0 packets with internal loop back IP address
0 physical broadcast
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 4 unreachable
140579 echo, 33742 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 timestamp replies, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
0 time exceeded, 0 info replies
Sent: 0 redirects, 3530 unreachable, 33744 echo, 140579 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp, 0 timestamp replies
0 info reply, 46795 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements
TCP statistics:
Rcvd: 19285 total, 0 checksum errors, 7 no port
Sent: 39402 total
BGP statistics:
Rcvd: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh, 0 unrecognized
Sent: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh
IP-EIGRP statistics:
Rcvd: 39154 total
Sent: 39275 total
PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
Queue drops: 0
State-Refresh: 0/0
IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0
Queue drops: 0
UDP statistics:
Rcvd: 5632168 total, 0 checksum errors, 9605 no port
Sent: 15536481 total, 0 forwarded broadcasts
OSPF statistics:
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
ARP statistics:
Rcvd: 36012 requests, 25 replies, 0 reverse, 0 other
Sent: 3590 requests, 1883 replies (41 proxy), 0 reverse
Drop due to input queue full: 0
drvirus#sh interfaces switching
GigabitEthernet0/1 ffff
Throttle count 0
Drops RP 29334 SP 0
SPD Flushes Fast 183378 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 196591 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 50222652 1410586379 38933488 2377282438
Cache misses 0 - - -
Fast 2501299905 502401799 1732463443 1178236678
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 36178 2170680 3643 233084
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1039 385469 2067 772027
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 2266 138297 6179 370740
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
Interface FastEthernet0/2 is disabled
GigabitEthernet0/2
Throttle count 0
Drops RP 0 SP 0
SPD Flushes Fast 785 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 1900 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 382927 34296776 382540 106683985
Cache misses 0 - - -
Fast 198 31569 0 0
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1900 114000 1813 108780
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1030 378010 1031 378377
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
GigabitEthernet0/3 drvirus
Throttle count 0
Drops RP 15 SP 0
SPD Flushes Fast 22435 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 194236 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 40507058 2970006619 56462488 1872816742
Cache misses 0 - - -
Fast 1758170357 386468928 2449949282 3706868609
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 105 8085
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 5 300 7 420
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 1034 379478
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1644 105280 250040
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1644 105472 256356
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#
ANy help ??????!!!!!can some one determin if :
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
has a relation to my high cpu
her is agian my cpu process :
drvirus#sh processes cpu sorted
CPU utilization for five seconds: 69%/51%; one minute: 62%; five minutes: 59%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 22165548 147317354 150 7.60% 6.54% 5.74% 0 IP Input
16 682988 2637213 258 3.61% 0.70% 0.37% 0 EnvMon
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
270 484700 4987094 97 0.76% 0.84% 0.86% 0 PPP Events
260 746640 483367 1544 0.30% 0.51% 0.51% 0 L2TP mgmt daemon
112 1082540 228491 4737 0.30% 0.31% 0.31% 0 CEF: IPv4 proces
190 596 755 789 0.30% 0.02% 0.00% 2 SSH Process
279 461184 78909 5844 0.30% 0.39% 0.45% 0 VTEMPLATE Backgr
52 954592 29823 32008 0.30% 0.31% 0.31% 0 Compute load avg
272 53744 2782461 19 0.23% 0.17% 0.16% 0 IPHC Admin
261 513524 428266 1199 0.23% 0.38% 0.37% 0 L2TUN Applicatio
142 31888 35627222 0 0.23% 0.19% 0.20% 0 HQF Shaper Backg
258 570384 1602872 355 0.15% 0.18% 0.17% 0 RADIUS
78 43280 392561 110 0.15% 0.10% 0.08% 0 ACCT Periodic Pr
281 52340 385568 135 0.07% 0.08% 0.09% 0 IP-EIGRP: PDM
40 37300 138153 269 0.07% 0.09% 0.10% 0 Net Background
77 145860 443602 328 0.07% 0.06% 0.07% 0 AAA ACCT Proc
110 31060 53876 576 0.07% 0.03% 0.02% 0 IP RIB Update
45 11868 52400 226 0.07% 0.01% 0.00% 0 IF-MGR control p
115 20164 103667 194 0.07% 0.02% 0.00% 0 PPP IPCP
102 181600 489310 371 0.07% 0.14% 0.15% 0 SSM connection m
143 3148 1461382 2 0.07% 0.01% 0.00% 0 RBSCP Background
80 19488 22128 880 0.07% 0.02% 0.00% 0 CDP Protocol
23 189412 10771 17585 0.00% 0.15% 0.04% 0 AAA high-capacit
22 0 1 0 0.00% 0.00% 0.00% 0 CEF MIB API
21 0 2 0 0.00% 0.00% 0.00% 0 ATM Idle Timer
20 376 153594 2 0.00% 0.00% 0.00% 0 ARP Background
24 0 2 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
25 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
26 1376 26590 51 0.00% 0.00% 0.00% 0 DDR Timers
31 4 30 133 0.00% 0.00% 0.00% 0 EEM ED Syslog
27 0 5 0 0.00% 0.00% 0.00% 0 Entity MIB API
33 324 147392 2 0.00% 0.00% 0.00% 0 GraphIt
34 0 2 0 0.00% 0.00% 0.00% 0 Dialer event
28 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun
36 0 2 0 0.00% 0.00% 0.00% 0 XML Proxy Client -
We've installed a new Audiocodes Mediant 1000B gateway for our customer. They only have about 6 users enabled for Enterprise voice and using Lync for all calls. They have an intermittent problem whereby the first call attempt to a number on the
PSTN fails with 12000; reason="Routes available for this request but no available gateway at this point". There is only one PSTN gateway installed. All routes point to this gateway. What I found initially is that the calls
were failing after 10 seconds which is the default "failovertimeout" in the OutboundRouting.exe.config. I found this post http://voipnorm.blogspot.co.uk/2012/06/lync-2010-gateway-timeout-call-failures.html and
changed the value to 20 seconds. Subsequent failures failed after 20 seconds (the new value). The interesting thing is that the second attempt even a couple of seconds later succeeds. My Lync server event log has 46046 "A call to a PSTN
number failed due to non availability of gateways." for the failed call and 46047 "A PBX gateway is now responding to requests after some failures." for the successful call moments later.
My environment is Lync 2010. A single enterprise edition Front End with collocated mediation. The server is virtual and in a different physical location to the gateway. The two sites are connected via a LES1000. The RTT between the
sites is very low so it isn't necessarily networking.
In the Syslog output on the Audiocodes we don't see the call even reach the gateway. It's likely that Lync has simply marked the gateway as down and doesn't route the first call. Then it wakes up and marks it as up and routes the next call.
Update wise I'm on 4.0.7577.183, 199 and 217 for those that are up to date and the only components that are behind say that 223 is available. Those being Core Components, Lync Server, Conferencing Server and Web Components.
As I said, this is intermittent, apparently doesn't happen for every user (which I don't buy), but is easily replicated on request.
I definitely think changing the failovertimeout value has reduced the number of failures. But realistically I don't want users sitting there for 20 seconds before their call fails. Or 19 seconds for the call to route.
I've found a few posts on this and similar issues. I don't get the 25051 or 25052 errors.
Any help gratefully appreciated.
Regards
Randy Chapman
Best Regards Randy ChapmanTry to change the value of Failovertimeout to 1000.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Material Master Update from group routing.
Dear All,
When we make material routing. in CA02>scheduling>Results--->Update material master (marking). can be done for the lead time scheduling Purpose. and update in CA96.
But when we use Group Routing, and assign multiple materials in routing header, and then go for
CA02>scheduling>Results--->** (no Material Master Update tab Appeared)
Do we have a solution for this?
Thanks & regards
RaghuDear,
Follow these steps,
Scheduling in routing (CA02 ) as :
Call up the operation overview for the routing.
Choose Extras-- Scheduling -- Schedule.
You reach the Scheduling dialog box.
Maintain the data on the dialog box. The system proposes Backward scheduling for the scheduling type.
Choose Continue.
You reach the Enter overview variant dialog box 00000001.
Enter the overview variant you want to use to display the scheduling results. Choose Continue.
The routing is scheduled. You reach the Schedule Overview screen containing the scheduling data.
After the scheduling run has been carried out, click on scheduling Result-- update material master
You use this function to update material master. Go to the CA96 and update material master.
Please try and come back.
Regards,
R.Brahmankar -
How can I route my audio interface inputs to Logic Express inputs?
Hello,
Logic Express can 12 inputs to record audio on.... fair enough.
My MOTU Traveler, together with ADAT connected Mackie Onyx 800F have 16 inputs...
How can I use the first 4 inputs (XLR) together with the last 8 input (ADAT)
Logic only seems to count from 1 to 12!
(After reading the manual, It seemed to be solved by making new Audio Input Objects in the Environment, but unfortunately these objects where removed from Logic Express)
Does anybody have the solution?
Thanks a lot.
Greetings,
MarkHi Michael, thanks a lot!
Unfortunately it didn't solve my problem yet. I tried
the audio/midi utility and found that the inputs
can't be turned off. Is there not a environment patch
possible, that I can load that puts the inputs in the
right order? I hope so!
Greetz,
Mark
The Environment doesn't route audio; it routes MIDI. There are audio objects IN the Environment, but you can't shuttle audio around like that.
You have to remember that LE is an entry-level piece of software. You might think Garageband is entry level, and I think it should be, but in reality, LE is VERY crippled. Don't get me wrong, I'm not ragging on Logic as a program; I think Logic is great. But Apple has made some poor choices with respect to the features of LP that get crippled in LE.
Sorry to digress from your original topic, but I think this is a bigger issue. The difference in price between LP and LE is enormous. That difference should be due to the fact that LP has plugs and effects (and other fairly esoteric features, like surround mixing, that most people don't need), and that justifies the price difference. Remember, when Emagic sold Logic (pre-Logic Pro 6), those effects and instruments cost a LOT more than the difference between LP and LE. LP is really a steal for what you get. LE is a poor substitute.
Seriously, LE is a lot less than just a lite version of LP; it's crippled by things like the 12 input/output thing (what is the point?), the useless Auxes, and numerous other little things that keep it from really competing with other 'lite' sequencers like Cubase SL or Audiodesk.
Anyway, I think the answer to your question is, if you need to record more than 12 simultaneous tracks, or you need flexibility in accessing your hardware's inputs and outputs, you need a better program.
Fortunately, the upgrade cost to LP isn't that much, nor is the crossgrade to Digital Performer... -
Setting up a router...
i am currently trying to set up a linksys wireless router in my house. the setup wizard works only on windows so i have to do it with my roommates computer. it's now asking me for the following:
connection type, ip address, subnet mask, gateway, dns 1, and dns 2.
i have no clue where to find this information on a windows pc. can someone please help me out?
also, is there a way to bypass this ridiculous wintel wizard? i looked around and saw that you can configure the router directly by going to http://192.168.1.1. the thing is, when i get to the config page, i am at a loss for what to do to get the thing working. anyone? thanks.No problem. Sorry, I don't have an AIM account. I usually can't keep up with IMing. Must be an age thing.
I downloaded the guide from Linksys for your router, so I should have a better chance of getting you setup properly now.
Ok, let's start by making sure your connected properly. For this part, we are going to use a wired connection to the router. Once we get you on the Internet, we can tackle the wireless part. So you will need an ethernet cable to connect your Mac with the router.
Looking at the back of the router, you would (as a minimum) have the following connections already established:
1. An ethernet cable between your cable modem & the Internet port on your router, and
2. The power cable connected to the power port on the router.
We are now going to want to connect a second ethernet cable between your Mac Ethernet (<->) port and any one of the ports, marked "1" - "4" on the router. (Doesn't matter which one, pick your favorite number.)
Power up your Mac, and then, open Safari and try any website, like Google for example. Can you get it to open?
If not, our next step is to make sure you Mac is properly setup to "talk" to the Internet with TCP/IP. -
How do I use AO update in the Route signal.vi
Hi support,
My goal is to create a waveform (to buffer it) and output it using the analog card (PCI-6713) N times and with the frequency F. Apperanlty this is done using a (actually 2) digital counter(s) on the PCI-6602 card.
This is done using route signal.vi using "AO update". However I have not managed to get it working. I only get error -10341. So my questions are how do I do it? More specificly how do I use AO update in the Route singal.vi Do I need to conect the cards in any perticular way (cabels or so)? Also do you have more information about how the vi route signal works (the help file does not help me much)?
Grateful for all help.
I'm using labview 6.0 as developpement platform, and using the PCI-6601, PCI-67
13 and a PCI-7344 cards. Since the program is quite large I will only send a portion of it, the pulseGen is supposed to generate the waveform (loaded as a text file, also submitted) the digital output used is in case 1 (in pulseGen) the analog output is in case 3. The MissingWaveform.vi is just to ensure that a waveform is supplied to the pulseGen.vi
Sorry about the mess.
/ChatriCabling and Interfacing between Boards: You have capability for direct simultaneous connection between 6713 and 6602 (also 6601) via the RTSI bus, but you need to get a cable to connect between the boards. You can connect between the boards using the I/O pins of their respective signal conditioning hardware. These connections are slower. There are also PFI (Programmable Function Interfaces) connections that are set within the VI's.
All that said, it is not obvious why you want to use the RTSI. You can use the PCI-6713 to generate AO. Presumably you have some signal conditioning accessory; which ever pin of that accessory the AO appears on, you wire it over to the SC accessory for the 6601 and the appropriate pin for the counter gate or
source you want to use.
Suggestions: Don't try to work in the context of your big VI for now. Get the AO bit and the counting bit to work together by themselves. Then shoe-horn them into the big VI. Also, consider a call to the NI help line. They are very good. 800.433.3488 (800IEEE488)
In case you hadn't noticed the DAQ cards and Counter/Timer cards come in different flavors and there are specific example VI's to suit. 6602 uses NI-TIO chip, but PCI-671X are DAQ-STC. Again the NI help people are good at catching this kind of stuff.
Your question is rather large and hard to manage. Perhaps if you break it down into small chunks the advise will be more free flowing.
mike -
How do I get rid of the flashing file with a question mark in it?
I wanted to start clean on my MacBook Pro osx 10.9.4. So I did the command r and erased what I thought was the right one. I restarted my computer and did the command r again and what came up was internet recovery. It can't find my internet because it's WEP and I don't know to change it to wpa. So I restarted my computer again and I didn't do the command r but just let it load itself to see what would happen and all I get is a flashing file with a question mark. I don't know what to do. Someone please help me.
Do you get this display?
If so, you have to select an Internet connection. Do not expect quick response time in this mode. All activities in this mode will be lengthy.
Ciao.
Maybe you are looking for
-
How can I run a script when an application quit??
Greetings all, I'm trying to write a script, which can be triggered automatically (to do some stuff) at the time when a given application quit. I was playing around with this test script, taking "TextEdit" as an example - it just prints a message whe
-
What are collaborators in java?
hey, i was reading an article about dependency injection and it says: "Dependency Injection has several important benefits: For example -Because components don't need to look up collaborators at runtime, they're much simpler to write and maintain....
-
Should I use Tcode FR04 to set a new year Budget payment without having close the last year period (12/2006) ? Do anyone can help me? Thanks a lot!
-
Since the last iOS update - the one released after the location cache issue arose - my battery life has been dropping like crazy. From a full overnight 100% charge, it is dropping at a rate of 10-12% per hour. And that's in standby. Unheard of pre-up
-
Search does not work until you open folder
I tried to search for a keyword on drive F (all pictures). I had the correct drive in the "look in" box, and had the boxes checked for "search indexed and non-indexed files". I got the dreaded "No Items to display" on the screen. I then opened the fo