B2B using JMS and Processing Messages with Message Driven Beans

We want to be able to use B2B to send messages to a JMS queue and then process messages from B2B using a Message Driven Bean. Is this supported.
We are using B2B 10.2.0.2 with Patchset 4.

Hello,
In 10.1.2.0.2 B2B , as part of the internal Delivery channel B2B can only send and receive messages from JMS queues.
Rgds,Ramesh

Similar Messages

To use JMS and JNDI in JDev 9.0.3.4

Do I need to add additional librararies in order to use JMS and JNDI along with EJB's in the enterprise application I'm creating?

No the article is not applicable for 9.0.3 I've never tested the compatibility of the 9.0.3 + Struts integration - obviously it does not work.
What does work is the ADF bindings used in 9.0.5 and above which can be safely used with newer versions of Struts.

I updated to yosemite and now if someone is using imessage and sends a text message to my phone it doesn't show up on my phone but does on my computer. I don't want messages on my computer! How do I get this to go away and work like it used to?

I updated to yosemite and now if someone is using imessage and sends a text message to my phone it doesn't show up on my phone but does on my computer. I don't want messages on my computer! How do I get this to go away and work like it used to?

Follow the instructions under the heading "How to unlink a phone number" on this page.

I just got the newest macbook air and it came with messages beta, how do i get rid of it?

I just got the newest macbook air and it came with messages beta, how do i get rid of it?

If the MBair has Mountain Lion installed then iChat has been replaced with Messages. (It's no longer in beta).

How to configure Integration B2B to request and process AS2 Sync MDN

Hi,
Is it possible to configure B2B to request and process sync MDN in Custom Document Over Internet scenario?
I have set up the TP Delivery Channel's Acknowledgement mode to Sync but It does not work for outgoing documents. Our trading partner sends back MDN over the same https connection but it only results in an error. The business message status of is Wait Ack for few minutes and then changes to Error:
Business Message Details
Collaboration
Revision
Business Action          PROCESS
Revision          1
Process Protocol
Exchange Protocol          AS2 - 1.1
B2B Message Id          1036
Protocol Message Id          <1036@as2test>
Protocol Collaboration Id
Receive Time Stamp          April 21, 2009 2:37:43 PM
Send Time Stamp          April 21, 2009 2:37:43 PM
Acknowledge Mode          Sync
Reply Mode          Async
Agreement          TP_TEST_AGR
Message Date Time          April 21, 2009 2:37:43 PM
Error Code          AIP-50079
Message Type
State          Error
Remaining Retry          0
Acknowledge Type          Document Exchange
Direction          Outbound
Time To Acknowledge
Sending Trading Partner          HOST_TEST
Wire Message          View
Correlated Message
Payload          Payload
Transport error: [IPT_HttpSendError] HTTP encounters send error :.
Premature EOF encountered
Also our trading partner reports that he gets the message six times during the time between Wait Ack and Error status and each time send Ack. Nothing is visible in b2b.log in that time.
When we switch to Async Ack, B2B also sends message six times and each time receives Async MDN. This time however, each MDN is received and processed correctly. Our request has status Complete, until the 6th Ack is received, then it changes to the same error as above.
Have any of you experienced above error? Is it at all possible to process AS2 MDN's correctly especially in Sync mode?
Thank you in advance.

Just consider your BPM is receiver, and sender:
Src --> BPM (BPM is Receiver)
==========
Sender Agreement (If it is IDOC or HTTP, then you do not have to create)
Commnunication Channel
Receiver Determination
Interface Determination
BPM --> Target (BPM is sender)
============
Receiver Determination
Interface Determination
Communication Channel
Receiver Agreement
If your BPM interact with other systems, you will have more Receiver Determination and Interface determination, possible Receiver agreement
Hope this clear your doubts
Liang

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again

Receiving E-Mail and processing it with ABAP

Hi,
We are able to send and receive mail from our SAP System,
i have implement Receiving E-Mail and processing it with ABAP according to following blog
/people/thomas.jung3/blog/2004/09/09/receiving-e-mail-and-processing-it-with-abap--version-610-and-higher
but when we try to send the mail to address which specified for inbound mail processing in sap it's gives me following error
554 tranasaction failed.
and in sap system following dump is generated for mailuser which is for sapconnect.
Runtime Errors         RAISE_EXCEPTION
Short text
    Exception condition "CNTL_ERROR" raised.
Error analysis
    A RAISE statement in the program "CL_GUI_CUSTOM_CONTAINER=======CP" raised the
     exception
    condition "CNTL_ERROR".
    Since the exception was not intercepted by a superior
    program, processing was terminated.
Information on where terminated
    Termination occurred in the ABAP program "CL_GUI_CUSTOM_CONTAINER=======CP" -
     in "CONSTRUCTOR".
    The main program was "RSM04000_ALV ".
    In the source code you have the termination point in line 62
    of the (Include) program "CL_GUI_CUSTOM_CONTAINER=======CM001".
plese help me to resolved this,
regards,
kinjal

Hi Kinjal,
I haven't studied to code , so cannot comment.
Try to post a comment at the blog and divert the author's attention to your question here.
Regards,
Siddhesh

Can I use Oracle BPEL process manager with other AS and DB

Can we user oracle bpel process manager with jboss application server and postgresql database.. is it possible..
and what will be the price.. per licencse when i go to just purchase Oracle BPEL process manager

MAke sure you have not set ANY environment variable related to Oracle / BEA / Java / LD_library path. Use the following script to unset / set the initial settings:
#!/bin/sh
unset ORACLE_BASE ORACLE_HOME ORACLE_SID ORACLE_TERM
unset LD_LIBRARY_PATH LD_LIBRARY_PATH_64
unset CLASSPATH JAVA_HOME
export PATH=.:/usr/sbin:/usr/bin:/usr/local/bin:/opt/VRTS/bin
export BEA_HOME=/appl/oracle/products/9.2/weblogic
Marc
http://orasoa.blogspot.com

Is it possible to create and process PO with the line without value?

Hi,
I am wondering whether is it possible to create and process the PO with the lines without the value?
I was thinking that this process would allow me to better track and understand the pallets which arrive to the site so I have set up the pallet as a material but systems doesn't allow me to order the line (pallet) without value?
Or maybe there is other way which will allow me to track the pallets within the system?
Many thanks,
Sylwia

Dave,
Thanks for the reply. Of all the suggestions I've received this seemed to
be most promising. I gave it a try and the problem is that when I attempt
to save as optimized a message box pops up and says I have to save my
document first. Low and behold when I save it, compression occurs. Even
when I select the options you suggest I'm left with a compressed document.
I'm using Acrobat Pro X
Jeff
From:   Dave Merchant <[email protected]>
To:     Jeff Ross <[email protected]>
Date:   01/06/2011 09:35 AM
Subject:        Is it possible to create and save a .PDF
without any compression to the resulting .PDF?
You don't want the UncompressPDF plugin - that's designed to split out the
COS objects but doesn't remove the Flate encoding (plus if you've never
compiled a plugin before, it's not really the time to learn).
Instead, simply save your PDF file using the PDF (Optimized) file type,
click the Settings button and under "Clean Up" - "Object compression
options", choose "Remove compression". Turn everything else off if you
want to retain the PDF content exactly as it was before.
Your document-level scripts will then be in the file as plain text.

Using Functions and/or Graphs with Custom Cell Formats in Numbers

I am attempting to use the AVERAGE function or create a graph in Numbers for cells with a custom format, however, I keep receiving an error message telling me that "Numbers can't be divided by Zero" or an empty graph.
The format I am using is for a split time for a certain distance, as in time it takes a runner to go around a track: minute:seconds.milliseconds i.e. 1:56.4
Is there a solution to the formatting or another way to accomplish having the correctly formatted cell and still be able to use functions and graphs.

Hi nich.lee,
You can't chart Duration formatted data without first converting it to another format. Also, you will get an error if you attempt to use the AVERAGE function on an empty range.
Here's an example of charting Duration data by using a conversion...
Best regards,
Jerry

Cannot burn DVD (using iDVD, and iMac G5 with Superdrive)

Hi. I'm trying to burn an iMovie onto a DVD-R (16x). I have an iMac G5 w/ Superdrive (PIONEER DVD-RW DVR-K04F). I have plenty of available disc space. iDVD goes through the entire burn process, then at the very end it spits out the disc with these errors:
The recording device reported the error #8: No additional sense information. (0x00, 0x00.)
The recording device reported the media error: Power calibration area error. (0x73, 0x03.)
Can someone PLEASE help me? What am I doing wrong?
THANK YOU!

Could be the brand of media you are using. Most users here find the most reliable to be Verbatim DVD-R.
Also, try burning at a lower speed.
Using 16x DVD media is fine - in fact it is difficult to buy any other - but there is a consensus in the Apple Support Forums that a slower burn is a better burn and that the most reliable brands are Verbatim, Maxell and Fuji, all DVD-R, burned at 2x or 4x (slow burns are better burns!). I always use Toast for burning.
I generally use Verbatim and when I can't get those, Fuji, and have never had a coaster from either.
Plenty of coasters in the early days from Sony, TDK and a few others.
The term "Best" means the fastest speed that the drive told Toast it can write to a specific disc. The drive's firmware and info on the disc decide what speed burns are available. When you press the speed setting button in Toast (after inserting a disc) you'll likely see some speeds in italics and some in bold face. The ones in bold face are supported by that media on that drive. The fastest one is what Toast calls Best.
Audio CDs in particular should be burned at the lowest supported speed.
Verification is a good indicator the disc is burned okay. However, other DVD players can still have problems with the disc. Media problems with various drives is not uncommon. Slower burning may reduce the chance of those problems, and is one of the reasons why RW (read/write) media is always rated slower than DVD-R.
There are some interesting facts here:
http://www.osta.org/technology/dvdqa/dvdqa4.htm and here:
http://www.osta.org/technology/dvdqa/dvdqa4.htm
But many will tell you that the 'slower burn is best' theory is outdated. Who really knows? At the end of the day, if your home-made DVD was verified by Toast and will play anywhere on anybody's DVD player, then that is the result we are all after!

Use of parallel processing profiles with SNP background planning

I am using APO V5.1.
In SNP background planning jobs I am noticing different planning results depending on whether I use a parallel processing profile or not.
For example if I use a profile with 4 parallel processes, and I run a network heuristic to process 5 location products I get an incomplete planning answer.
Is this expected behaviour? What are the 'good practices' for using these profiles?
Any advise appreciated...

Hello,
I don't think using parallel processing profile is a good idea when you run network heuristic, since in network heuristic, the squence of the location/product is quite important. The sequence is determined by low-level code, as you may already know.
For example, in case of external procurement, it must first plan the distribution center then the supplying plant, and in case of inhouse production, it must first plan the final product then the components.
If you use parallel processing, the data set which is sorted by low-level code would be divided into several blocks and be processed at the same time. This may mess the planning sequence. For example, before the final product is planned in one block, the component is already planned in another block. When it plans the final product, new requirement of the component is generated, but the component will not be planned again, which results supply shortage of the component .
If there're many location products, maybe dividing the data set manually is a good practice. You can put those related location products in one job, and set several background jobs to plan different data set.
Best Regards,
Ada

Using ExtensibleEnvironment and Command Pattern with 3.7.1 Release

I am trying to port my project 3.6 project to 3.7.1. I am using the Extensible environment from the jar coherence-3.6-common-1.7.3.20019.jar
While starting the cluster I am getting the below errors.
Is there a confguration showing how to configure the Command Pattern and Extensible environment with XSD validation in 3.7.1?
Exception in thread "main" (Wrapped: Failed to load the factory) (Wrapped: Missi
ng or inaccessible constructor "com.oracle.coherence.environment.extensible.Exte
nsibleEnvironment(String)"
<configurable-cache-factory-config>
<class-name>com.oracle.coherence.environment.extensible.ExtensibleEnvironment<
/class-name>
<init-params>
<init-param>
<param-type>java.lang.String</param-type>
<param-value>C:/work/development/workspace/java/Coherence-Rest/cfg/cache-s
erver-config.xml</param-value>
</init-param>
</init-params>
</configurable-cache-factory-config>) java.lang.reflect.InvocationTargetExceptio
n
at com.tangosol.util.Base.ensureRuntimeException(Base.java:288)
at com.tangosol.net.ScopedCacheFactoryBuilder.getDefaultFactory(ScopedCa
cheFactoryBuilder.java:311)
at com.tangosol.net.DefaultCacheFactoryBuilder.getSingletonFactory(Defau
ltCacheFactoryBuilder.java:48)
at com.tangosol.net.DefaultCacheFactoryBuilder.getFactory(DefaultCacheFa
ctoryBuilder.java:121)
at com.tangosol.net.ScopedCacheFactoryBuilder.getConfigurableCacheFactor
y(ScopedCacheFactoryBuilder.java:112)
at com.tangosol.net.CacheFactory.getConfigurableCacheFactory(CacheFactor
y.java:126)
at com.tangosol.net.DefaultCacheServer.getDefaultConfigurableCacheFactor
y(DefaultCacheServer.java:364)
at com.tangosol.net.DefaultCacheServer.main(DefaultCacheServer.java:197)
Caused by: (Wrapped: Missing or inaccessible constructor "com.oracle.coherence.e
nvironment.extensible.ExtensibleEnvironment(String)"
<configurable-cache-factory-config>
<class-name>com.oracle.coherence.environment.extensible.ExtensibleEnvironment<
/class-name>
<init-params>
<init-param>
<param-type>java.lang.String</param-type>
<param-value>C:/work/development/workspace/java/Coherence-Rest/cfg/cache-s
erver-config.xml</param-value>
</init-param>
</init-params>
</configurable-cache-factory-config>) java.lang.reflect.InvocationTargetExceptio
n
at com.tangosol.util.Base.ensureRuntimeException(Base.java:288)
at com.tangosol.run.xml.XmlHelper.createInstance(XmlHelper.java:2652)
at com.tangosol.run.xml.XmlHelper.createInstance(XmlHelper.java:2536)
at com.tangosol.net.ScopedCacheFactoryBuilder.getDefaultFactory(ScopedCa
cheFactoryBuilder.java:273)
... 6 more
Caused by: java.lang.reflect.InvocationTargetException
at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstruct
orAccessorImpl.java:39)
at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingC
onstructorAccessorImpl.java:27)
at java.lang.reflect.Constructor.newInstance(Constructor.java:513)
at com.tangosol.util.ClassHelper.newInstance(ClassHelper.java:694)
at com.tangosol.run.xml.XmlHelper.createInstance(XmlHelper.java:2611)
... 8 more
Caused by: java.lang.RuntimeException: Can't create a NamespaceContentHandler as
the URI scheme [http] in [http://www.w3.org/2001/XMLSchema-instance] is not sup
ported
at com.oracle.coherence.environment.extensible.DefaultConfigurationConte
xt$Scope.establishNamespaceContentHandlerFor(DefaultConfigurationContext.java:62
5)
at com.oracle.coherence.environment.extensible.DefaultConfigurationConte
xt.ensureNamespaceContentHandler(DefaultConfigurationContext.java:94)
at com.oracle.coherence.environment.extensible.DefaultConfigurationConte
xt.processElement(DefaultConfigurationContext.java:254)
at com.oracle.coherence.environment.extensible.DefaultConfigurationConte
xt.processDocument(DefaultConfigurationContext.java:204)
at com.oracle.coherence.environment.extensible.ExtensibleEnvironment.set
Config(ExtensibleEnvironment.java:438)
at com.tangosol.net.DefaultConfigurableCacheFactory.<init>(DefaultConfig
urableCacheFactory.java:193)
at com.tangosol.net.DefaultConfigurableCacheFactory.<init>(DefaultConfig
urableCacheFactory.java:179)
at com.tangosol.net.DefaultConfigurableCacheFactory.<init>(DefaultConfig
urableCacheFactory.java:155)
at com.oracle.coherence.environment.extensible.ExtensibleEnvironment.<in
it>(ExtensibleEnvironment.java:154)
... 14 more

Hi
Is there a reason you are using the 3.6 version of the incubator with Coherence 3.7 and not the latest INC-10 version? I suspect the 3.6 Incubator does not support normal XML schemas.
JK

Is it possible to use fullscreen and exclusive mode with a jfilechooser?

is there a way to use them together? while in fullscreen exclusive mode the jfilechooser doesn't attach to fullscreen window and it halts the program.. I've tried setting the parent frame as the fullscreen frame but it's all glitched.. am I missing something?
thank you,
best regards,
Jacopo

For reference, the cross-post can be found here:
Is it possible to use network devices (cDAQ-9188) with a PXI Real Time system?
Jayme W.
Applications Engineer
National Instruments

Using generics and J2SE together with JSF

Hi
Has anybody experience with using JSF together with J2SE 1.5? Especially generics? I would like to use generics and other improvements from J2SE in the model objects.
Thnaks in advance ... Rick

JSF 1.1 is specified for J2SE 5, and the new specification (JSF 1.2 and JSP 2.1) does not include generics.
If you are talking in terms of ValueBindings or MethodBindings, there really isn't any point since the implementation could only make the cast for you; and it would still not be able to garuantee type safety (the only reason to use generics).
That's not to say you couldn't use generics in your own development, but I don't think you will see generics incorporated into the specification any time soon.
Jacob Hookom (JSR-252 EG)

B2B using JMS and Processing Messages with Message Driven Beans

Similar Messages

Maybe you are looking for