Bandwidth Calculation based on Network IP Address on SNMP Cisco 3750
Dear All,
Instead of getting bandwidth calculation on cisco switch via snmp for total in and out or based on port, is it possible to get the calculation of bandwidth for in and out for the C Class IP on the network ? That mean i can get the calculation for each of my network IP address from the Cisco, what i'm doing now is to get from my bridge server and i run the iptables and some bash script and also MRTG
Please advice. TQ
Hi Abhi,
you're welcome. Thanks for rating & marking as answered!
I have CISCO 6503 box also with me. Could you please confirm if feature would be supported on 6503 ethernet ports or not?
Have a look at the Release Notes:
http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/release/notes/features.html#wp2800031
"New Software Features in Release 12.2(18)SXF2
Support with Supervisor Engine 2 for these features, which are already supported with other Supervisor Engines:
- IP unnumbered for VLAN-SVI interfaces
-VLANs over IP unnumbered sub-interfaces"
I have to say I've never done this so far on a c6500 but I think you can rely on the RN.
HTH
Rolf
Similar Messages
-
How do I stop Firefox from redirecting me to another site based on my IPS address?
I work in California. Our corporate offices are in Oklahoma and my desktop computer is set up with an IPS address in OK. When I try to go to the CA website for AAA, Firefox redirects me to the OK website for AAA. How do I stop from being redirected to OK sites when trying to open CA sites?
hello eajames, sites can show you content and redirect you based on your IP address which will reveal your approximate location - there is not much a browser can do against this...
http://www.yougetsignal.com/tools/network-location/ -
Providing Access based on Client IP Address
Current Scenario -
SAP Portal is accessible directly and via Citrix (VPN).
Based on the URL alias - we have implemented Desktop Filtering.
eg if the URL ends with / internet - You get restricted roles
eg if the URL ends with / intranet - You get wider roles
In Production, we also have Netscaler Reverse Proxy and HTTPs settings in place for External (outside firewall) access.
New Requirement (Example) -
Based on the IP address of the client, determine which subnet it falls under and based on that -
If used within Citrix - Provide certain roles
If not used within Citrix - Restricted access / Redirect to a different URL on the redirect server.
Questions -
With the current desktop filtering in place based on URL determination and no specific restriction for inside/outside Citrix access -
1 - Please suggest which would be a good way to crack this? Inside Portal (IP address determination and SAP Logon modification) / Outside Portal (eg Citrix, Network OS Exit, Reverse Proxy etc) based on Best Practise ?
2 - Not sure if this is relevant : Find IP address of Client with webdybpro (This API works only in Web Dynpro and not PDK) ? I believe tweaking SAP Logon logic can get very painful and overtly complicated for such scenarios.
Thanks for your inputs ~ DhanzVivek,
On the coding front -
1 - Will reading the IP address in the header field x-forwarded-for retrieve right results if reverse proxy is in place ? Wouldnt it retrieve the proxy / load balancer IP instead of Client IP ?
2 - Also we have HTTPS settings for extranet access - So encrypted data (eg Client IP ) is transferred that the Web Dispatcher cannot manipulate ?
Please suggest.
Remember to be polite
Edited by: Anja Engelhardt on Jan 27, 2012 11:27 AM -
Bandwidth Limit based on Source IP?
Hi
I am trying to think of a way to apply a bandwidth limit based upon Source IP subnet.
I need to have the ability to limit both the outbound and inbound traffic.
So I created the following config:
policy-map bw-limit-inbound
class bw-limit-class
police 10000
class-map match-any bw-limit-class
match access-group 150
access-list 150 permit ip 172.16.99.0 0.0.0.255 any
If I apply the Service Policy inbound, it does police the upload to 100Kbps.
If I apply it outbound, it does nothing to the download.
Any reason for this?
I am applying this to an SVI
ThanksHi Guys
Just to update this thread, I figured out where I was going wrong!
As mentioned by Mikael, the ACL only shows traffic one way, hence why it was not applying the service policy to the download.
I have three subnets I want to Police both outbound and inbound so I started with Three ACLs:
access-list 197 permit ip 172.16.97.0 0.0.0.255 any
access-list 197 permit ip any 172.16.97.0 0.0.0.255
access-list 198 permit ip 172.16.98.0 0.0.0.255 any
access-list 198 permit ip any 172.16.98.0 0.0.0.255
access-list 199 permit ip 172.16.99.0 0.0.0.255 any
access-list 199 permit ip any 172.16.99.0 0.0.0.255
I then created the relevant class maps:
class-map match-all vlan998-download
match access-group 198
class-map match-all vlan999-download
match access-group 199
class-map match-all vlan997-download
match access-group 197
class-map match-all vlan998-upload
match access-group 198
class-map match-all vlan999-upload
match access-group 199
class-map match-all vlan997-upload
match access-group 197
Then the service policies:
policy-map download-limit
class vlan997-download
police 2000000
class vlan998-download
police 3000000
class vlan999-download
police 4000000
policy-map upload-limit
class vlan997-upload
police 200000
class vlan998-upload
police 300000
class vlan999-upload
police 400000
Then finally applied those to the relevant SVI:
interface Vlan102
ip vrf forwarding WAN2
ip address 10.20.2.2 255.255.255.0
ip nat inside
ip virtual-reassembly in
service-policy output download-limit
service-policy input upload-limit -
Interest calculation based on Net Due Date
Hi guys: I want the interest calculation based on net due date and not document date or posting date.
I tried to check the box "ALWAYS CALCULATE INT FROM NET DUE DATE in prepare item interest calculation step, but system gives me message
"Do not select "Calc.intrst from net due date" for this int.calc.type
Message no. F7128"
Here are my questions:
1- how can i make the system to calculate interest only after the item is due for payment - right now its calculating anyday after the document date
2- Is this the correct place in configuration to do this? (ALWAYS CALCULATE INT FROM NET DUE DATE )
3- Also in T code FINT, how can i run interest posting for only one item rather than all that show up in test run? I tried selecting/highlighting only one but it posts all.
thanks much
brianHI,
The system always calculates the interest from the document date of the invoice,
as of my knowledge there is no setting for the interest calculation from the net due date, so
what u need to do is when u are running the open item interest run u specify the period of only the date
from the net due date to required date as of u.
if u want to calculate the interest to paticular invoice and having two invoices
then u can run as per the document date and other thing is u can block the invoice for dunnig.
Regards,
Padma -
How to reset the network IP address from terminal/command line in Mac OSX?
Do anyone knows how to set the network IP address from terminal/command line in Mac OS X?
how about a GUI, ever heard of a GUI? it's this really neat thing, where you don't have to worry about remembering long strings of text to do something. Mac OS X actually has a rather decent one (that was sarcasm by the way, Mac is the best) you could have it done in like 30 sec, if you use the network pane of system preferences.
-
Shipment cost calculation based on HU's allowed packaging weight
Hi all,
I need to calculate a shipment cost based on the Means of Transport's Allowed Packaging Weight (MARA-ERGEW). After condition record determination of cost per ton in each case, the system must multiply this value times the allowed packaging weight.
I know that through customizing I can create a Condition Type with Calculation Base = 'C' (Handling Unit) and Calculation Type = 'D' or 'E' (Gross or Net Weight). This is almost what I need except for the Calculation Type, because Allowed Packaging Weight is not an option in the field's matchcode (Percentage, Fixed Amount, Quantity, Gross Weight, Net Weight, Volume, etc...).
Is there any way through customizing I can achieve this? Or how can I program a routine in the Pricing Procedure for the Condition Type in order to make the calculation based on the HU's Allowed Packaging Weight.
I appreciate your help!!Freight carriers charges weight on the basis of Weight / volume of the items.SAP shipment works on the same principle.
Cost of transporting ton of Potataoes is same as transporting 10 ton of aluminium between two known destinations.
Hence it is illogical to distributes cost on the basis of item value. However if still you want to distribute the same on value basis then maintain freight condition(%) in PO as per your prefined logic of distribution of freight cost.
It is well known fact that cost of freight % is always higher in Low value items & iis low in case of High value items.
Regards,
Sanjay Kohli -
Calculation based on date key figures in BEx
Hi Friends,
Hi Friends,
I need to creat report for sales order data, which involved the calculation based on dates.
In my cune iam having the data at the granual level with the dates as key figures. the calculation that i need to do is VTW = Actual PGI date - Customer want date.
1) whn i run the report at the granual level my VTW is working correctly. No issues.
2) when i run the report at higher levels the date fields are updated with X, as the system is unable to aggrigate the dates. The dates are at the material level in a sales order. I need to show the VTW at the sales order level (each one of the two dates are same for all the materials). So, when i run the report with out mataril at the sales order level...i wanto sea the bothe date fields in a single line and also the VTW calculated as the different between throse two dates.
3) Once we get the VTW correctly at the sales orde level. if i drill down the report for material, i want to sea both the dates in every record againest the matarial, but the VTW only aginest the first record...that is againest the sales order. I dont waht the VTW value repeated/duplicated for all the records againest the sales order,as VTW makes sence only at the Sales Order level.
Please suggest me hwo i can achive the resulsts by meeting both Point 2 and 3.
Thanks for ur help...in advance.
Thanks,
RenuHi..
I have the data from the extractore and in the cube as below.
SALES ORDER ITEM MATERIAL DATE1 DATE2
101 Item1 Mat1 01/01/2010 15/01/2010
101 Item2 Mat2 01/01/2010 15/01/2010
101 Item3 Mat3 01/01/2010 15/01/2010
I need the reports as below...
Report1:
SALES ORDER DATE1 DATE2 VTW (DATE2 - DATE1)
101 01/01/2010 15/01/2010 14
currently iam getting this Report1 output as below...
SALES ORDER DATE1 DATE2 VTW (DATE2 - DATE1)
101 X X 42
Report2: Out put required as below
SALES ORDER ITEM MATERIAL DATE1 DATE2 VTW (DATE2 - DATE1)
101 Item1 Mat1 01/01/2010 15/01/2010 14
101 Item2 Mat2 01/01/2010 15/01/2010
101 I tem3 Mat3 01/01/2010 15/01/2010
currently iam getting this Report2 output as below...
SALES ORDER ITEM MATERIAL DATE1 DATE2 VTW (DATE2 - DATE1)
101 Item1 Mat1 01/01/2010 15/01/2010 14
101 Item2 Mat2 01/01/2010 15/01/2010 14
101 I tem3 Mat3 01/01/2010 15/01/2010 14
As VTW is need to be measued at the sales order level and we always have the DATE1 & DATE2 as same for all the itesm, it should be shon as only 14 in the first record. It mean once iget the required output from Report one in a single line with VTW as 14, it should not repeat with every line , when i dril down the report for Items or materials.
Even if i can generate oly report2 as required in a single sheet ...that will be enough.
Plas kindly provide some solution as how we can achieve this,
Thanks,
Renu -
Query field calculation based on a characteristic field
Hi
I have a req wherein the query has a field "Balance". Now here the value of the Balance field is calculated based on another characteristic "0bal_flag". 0bal_flag has values "X" or blank. The 0bal_flag is actually a attr of 0gl_account and i have it as a nav attr in my cube.
The calculation goes like this....
If 0bal_flag = 'X' then "Balance" = balance (there is a balance field in underlying infoprovider)
else "Balance" = Debit -credit (these fields are also there in underlying infoprovider....)
So how do i achieve this...?
Since 0bal_flag is a char I cannot use it directly in a formula....
Thanks
GauravHi Gaurav,
Create a replacement path formula variable on the 0bal_flag with evaluate as boolean checked, you will get the values 1 when flag is X and 0 when the flag is initial, now you can use this 'formula variable' in the formula
((0bal_flag==1)balance)+((0bal_flag==0)(debit-credit))
hope this helps,
Rk. -
Calculation based on radio box Help PLEASE....
I am trying to make a text box perform a calculation based on whether or not a radio button is checked or not.
If the radio button named "Basting" in the "Quilting Type" group is checked then the text box "Basting Charge" should find the value of the "Total Square Inches" field and multiply that total by 0.015 and show the new total in the text box as a dollar value, if the radio button "Basting" is not checked the value in the "Basting Charge" field should be "-0-".
I can get the calculation I want from this:
var v1 = getField("Total Square Inches").value; event.value=v1*0.015;
but how to include the radio button function and the "-0-" ?Okay, I have now made a "check box" with the name of "Basting", not in a grouping.
This is the set up:
Text Field = Total Square Inches
Check Box = Basting
Export Value = Yes
Text Field = Basting Charge
Calculation for "Basting Charge" should be "0" unless the "Basting" check box is used, then it should get the value of the "Total Square Inches" and multiply that number by 0.015 and show this value in the "Basting Charge" box displaying as a dollar figure.
So if the value in the "Total Square Inches" is 12,000
and the "Basting" check box is used
The "Basting Charge" should read "$180.00"
if the check box is not used then it should read "-0-" -
Calculation based on Internal Table Row ID
Hi,
I have internal table, i want to do some calculation based on Internal table Row ID, wich will create system automaticlly and this id will uniq. I want to use this id in my program.
So how can i do this.
Ranveer.hi,
if u want to create this id automatically,use transaction SNRO,
or u can create t through programming too.eg. suppose field is 'id' in table 'customer'.
select * from from customer.
itab-id = sy-dbcnt + 1.
modify customer from itab.
u can use this id in calculations too, -
Prorate calculation based on Martial status
Dear Experts,
We have two types of the minimum of Housing Allowance(IT0014 - HA01WT):
1. 1000 Monthly for Single
2. 1500 Monthly for Married
And this changeable based on Marital Status Key on Info Type 0002. However; if the change of Marital Status happened in the middle of the month the Housing Allowance should be calculated on a pro rata basis.The System gives the employee the new Housing Allowance in full. Please provide me the logic or operation that we can use in the PCR
Pls let me know for any further clarification
Regards
SBI found solution on my own. please find below the rule
TABLEP0002 Read table fields
VARGBFAMST Tab.field VVVVV v.ky
1
WPALL?LAST ID = LAST?
N
Y
AMT?IZSHNG Comparison
ADDWT * OT Output table
<
RTE=FZ7N Set
RTE?1 Comparison
=
ZERO= NRA AmtNumRteTime = 0
RTE=FZ7T Set
AMT=IZMHNG Set
MULTI RAA Multipl.amt/no/rate
AMT/TKDIVI Division
ADDWT 1001 OT Output table
RTE-TKDIVI Subtraction
RTE*-1 Multiplication
AMT=0 Set
AMT=IZSHNG Set
MULTI RAA Multipl.amt/no/rate
AMT/TKDIVI Division
ADDWT 1001 OT Output table
>
AMT=IZMHNG Set
ADDWT * OT Output table
Now its calculating based on prorate basis for both single and married status...
Regards
Sanjai -
Query for Auto Calculation based on input of 2 Fields
Hi,
I would like to write a sql query to allow for auto calculation based on the Inputs of 2 other fields before Adding the Order.
For example. A query on Sales Order where I have Item 040634 (Code for a Flower) and Quantity 200.
I have a UDF (Bunching) where the value is 10, 15 or 20.
Based on the Bunching the result should be given in another UDF (Noofsleeves).
(Quantity) 200 / (Bunching) 10 = 10 (Noofsleeves)
The Order will be having multiple items where the Bunching can differ for each item.
Is it also possible to remove the calculated noofSleeves from Inventory.
I am using 2007A SP01 PL05Hi ,
You may try this: Apply this fms on other udf and auto refresh on the udf mentioned in the query (in your case Bunching).
SELECT $[RDR1.Quantity.number] / $[RDR1.U_UDF.number]
You may check these too.
cALCULATION OF udf ON UNIT PRICE
FMS
Thanks,
joseph
Edited by: Joseph Antony on Jul 8, 2010 12:31 PM -
Re-direct based on source ip address
Dear all,
i wish to redirect url traffic to another server based on their ip address. We currently have sharepoint server and was hoping to utilise it facilities to redirect to another server. https://www.abc.com to
http://www.abc.com/def
we have iis7 runnin in the backgroup if that help.. Would iis be a better choice?
Thanks in advance..
N DHANRAJHi Dhanraj,
I understand that you want to redirect the url from
https://www.abc.com to http://www.abc.com/def, you can try URL Rewrite rules to achieve this goal.
Here are some posts about this topic, you can take a look.
http://stackoverflow.com/questions/22182087/iis-rewrite-rule-to-redirect-specific-domain-url-to-different-url-on-same-domain
http://social.technet.microsoft.com/wiki/contents/articles/23074.sharepoint-2013-url-rewrite.aspx
Supportability of Rewrite and Redirects with SharePoint 2007/2010/2013
More about the IIS redirect, I would recommend you post in IIS forum below, there will be more experts assisting on this issue.
http://forums.iis.net/t/1153050.aspx?URL+Rewrite+for+SSL+redirection
Thanks
Daniel Yang
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected] -
Route call based on source IP address
Hello Guys,
Is there a way to route calls based on source IP address?
I want to redirect calls to specific queues based on the ip of the phone who's starting it.
Any ideas?
Thanks in advance.
Filipe LeiteHi Filipe
I'm assuming here that you are using CallManager rather than CME?
One option might be to use the 'device mobility' feature to assign a specific CSS to devices based on their IP subnet. That CSS could have the appropriate partitions to route to a seperate trigger that directs calls to a separate CSQ.
Of course, whether you can do this depends on whether it would be appropriate to override the device CSS in this way.
Aaron
Maybe you are looking for
-
IPhone 4s Voice mail notification not working after switching from Verizon to PagePlus.
iPhone 4s Voice mail notification not working after switching from Verizon to PagePlus. How can I get the notifications working?
-
Report Painter Output at Center
Dear Techis, From report painter output i m printing thru spool request i m getting output as at left side but i want it to come as center , so anybody pls tell me where i have to make setting at report painter or somewhere else.. Pls do the needful
-
Add button in POWL list and if i click on button it should dispaly details
Hi Experts, In POWL alv list for one column i need to add one button & if i click on that button i need to display data of that pertiuclar column. Please let me know if any body knows answer. Regards, Sri
-
Saving as Disc Image hangs/freezes and must force quit to exit
Hi, I've always been able to Save as Disc Image in order to make multiple copies. Now, it runs fine all the way until it gets to "Burn - Current Operation: Writing" where it freezes indefinitely. The beachball turns so I eventually have to force-quit
-
Install question CS2 Premium using CS4 Standard work?
Running iMac Power PC G5, 2GB SDRAM, and have checked all the system requirements to upgrade, good to go, now the question is... I have Adobe CS2 PREMIUM installed and need to upgrade to CS4. Will the CS4 STANDARD full version work to upgrade? or am