BarCode Not Reading

Hi Experts,
I connected BarCode reader to my system. When i tried to scan the barcode in item master its not displaying. i am new to Barcode . Can you tell me what i have to do to sort it out. Also tell me what are the settings i have to make to scan the code from my item and display in edit text of Itemmaster

Hello,
1.st Your scanner probable supports or not supports the bar code type what you are reading?
Open a NotePad, and read the barcode.In the notepad the scanner will print the readed code... it works...
2. In Item Master, if the Code you are reading with the scanner is a barcode switch to find mode, and stay on the BarCode field. Scan the code into the BarCode field. (if not found, the barcode field is not filled in Item Master Data)
3. Scanners can be customized command (chars) to be entered after reading... I am suggesting to send a TAB Key after a sucessfull read (you can find more informatiion in the Guide of the Scanner).
4. By Tab you can use a scanner in sales / purchase documents, by moving the barcode field to the first column of the Document lines.
5. No more development is necessary for scanners which are used as Keyboard input....
Regards,
J.

Similar Messages

Barcode not read by scanner

hi all.
i have create programe for printing barcode.programme running fine and i can print barcode on laser printer.but when i try to scan from barcode reader.its not reading by scanner.
whats problem with it????
i used following tutorial .
https://www.sdn.sap.com/irj/scn/wiki?path=/display/profile/newBarcodePrintinginSAPusingSmartforms

>
Usha Kommalapaty wrote:
> Hi,
>
> Software to be installed in all desktops in order to enable printing of barcode from their systems.
> So, for printing barcodes on laser and dot matrix printers, additional software should be made available on all desktops.
Not True, new barcode technology does not need any additional software in the desktop. (Refer Introduction part [here|https://www.sdn.sap.com/irj/scn/wiki?path=/display/profile/newBarcodePrintinginSAPusingSmartforms])
What symbology you have used, did you check whether your scanner supports the used symbology?
Regards
Karthik D

Leading zeros not reading in Barcode

I am trying to get a number field to read in a barcode. The field has leading zeros hard coded into the field to make it a uniform amount of digits. These zeros are not typed. The barcode will only read the information that is typed and will not read the zeros. Is there a way to change that.

If you are getting the values form an unformatted text field, then use the "valueAsStrting" property or you could pad the value to include leading zeros.
You can pad a value with leading zeros either by concatenating a string of zeros for the length to the value and them taking the right most number of digits or use 'util.printf()' method to format a fixed length string with leading zeros.

Barcode is not reading using the barcode reades

hi
In my application i am generating barcode.But the barcode scanner is not reading this value.I am using CODE128 and also tried with code128A.
it is urgently neede pls help me.
will give points for helpful answers
Warm regards
Shanto Aloor

Hi Shanto,
The problem might be the width of the barcode. Try increasing the width, and the reader would recognise it.
Regards
Anil Madhavan

Barcode scanner not read Quantity like 10 ,20,40...

HI ALL Experts
My barcode scnner gun not read Quantity of item they only read item code read as barcode
please if any setting in barcode scanner then tell me
Thanks
kalpen

I have not tried it but generate a barcode from some app and have it sepperate from the item code. When the user selects quantity then scan the quantity code it should work. try this site. http://www.barcoding.com/upc/

Enable paperforms barcode in reader

Please forgive me if this is the wrong forum or if this has already been answered (first time post). I've done extensive searching and reading and, despite many articles and posts related to the topic (here and other blogs) I can't get the answers I'm looking for - and can't seem to get an adobe representative to return a call.
I am an existing Adobe Acrobat Pro customer (group license - windows7 32/64b) looking to enable paperforms barcode extensions in reader. We are a relatively small shop and expect that we would add pdf417 codes to a handful of existing forms and expect returns from several hundred users. If I understand documentation correctly, licensing can be on a per-form basis or per-user basis. I do not expect that the per-form basis (max 25?) would be exceeded over several years.
I've designed a set of forms in LiveCycle Designer 8.2 with pdf417 barcodes and need to add whatever licensing is necessary to extend this functionality to Reader. We do not have, nor want to build out a full livecycle enterprise system/server/integration. I believe this is a bit of overkill for our needs. We have a decoding and data extraction workflow in place that satisfies the downstream data needs.
What I'd like to see is a licensing option that would allow us to extend paperforms barcodes to reader and continue to design forms in livecycle designer. If someone can point me in the right direction or an Adobe representative can contact me directly to discuss particulars that would be greatly appreciated.
Cheers

George,
Thanks very much for the response. I've contacted the datalogics folks and they've been very helpful (got a test version of pdfjt). I haven't actually built out a test for this (gonna do this today) but it seems like this would be more involved. Do you know if the datalogics extension key/certificate can be embedded in existing forms - without having to build the forms through the pdfjt? If this is how these sorts of tasks are accomplished - then I'll move in this direction but it does seem like one should be able to embed the key (even manually if needs be) without all the overhead of a server-based solution.
regards,

Adobe Media Encoder for CS4 error Could not read from the source

Hello,
I get an error when I try to export from Premiere CS4. It doesn't matter how I export. Seems like an easy fix, but I can't figure it out. Any help is appreciated:
- Source File: C:\DOCUME~1\ARTWHI~1\LOCALS~1\Temp\extra and b roll.prproj
- Output File: E:\Living Accused Movie Transfers\video\Cindy at table.avi
- Preset Used: NTSC DV
- Video:
- Audio:
- Bitrate:
- Encoding Time: 16:10:34
1/21/2009 9:50:25 PM : Encoding Failed
Could not read from the source. Please check if it has moved or been
deleted.
Thank you
Art

When you attempt to encode media with Adobe Media Encoder CS4 on Windows, the following error message appears in the text file (AMEEncodingErrorLog.txt) that opens when you click the error icon: "Encoding Failed. Could not read from the source. Please check if it has moved or been deleted."
If it's that correct, you removed an earlier version of Adobe Premiere Pro or Adobe Creative Suite on the same computer.
Do one or both of the following solutions:
Solution 1: Create a shortcut to the Premiere Pro executable file, rename the shortcut to Premiere, and move the shortcut to C:\Program Files\Common Files\Adobe\dynamiclink.
Close all Adobe applications.
In Windows Explorer, navigate to C:\Program Files\Adobe\Adobe Premiere Pro CS4. (If you installed Premiere Pro CS4 in a location other than the default of C:\Program Files\Adobe, then navigate to your custom installation location.)
Right-click on Adobe Premiere Pro.exe (which might appear without the .exe extension) and choose Create Shortcut.
Rename the newly created shortcut to just Premiere.
Important: The name of the shortcut must be exactly Premiere with no other characters.
Open a second Windows Explorer window, and navigate to C:\Program Files\Common Files\Adobe\dynamiclink.
Move the Premiere shortcut that you created into the dynamiclink folder.
Solution 2: Remove and reinstall all Premiere Pro CS4 components or all Adobe Creative Suite 4 components.
Do one of the following:
Windows XP: Choose Start > Control Panel > Add or Remove Programs.
Windows Vista: Choose Start > Control Panel > Programs and Features.
In the list of installed programs, select Adobe Premiere Pro CS4, Adobe Creative Suite 4 Production Premium, or Adobe Creative Suite 4 Master Collection.
Click Change/Remove (Windows XP) or Uninstall (Windows Vista).
Follow the on-screen instructions to remove all components of Premiere Pro CS4 (including Adobe Encore CS4 and Adobe OnLocation CS4) or to remove all components of your edition of Adobe Creative Suite 4.
Re-install your Adobe software.

When I was talking on phone, suddenly the phone was switched off. i tried to switch it on but it gave the message....connect to itunes for set up. when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it

when I was talking on phone, suddenly the phone was switched off.
i tried to switch it on but it gave the message....connect to itunes for set up.
when I connected it to itunes...it gave the message, itunes can not read data from this iphone, restore it to factory settings. It also said while restoring ypu will lose all media data but you can restore the contacts.
I restored the factory settings....the phone was on recovery mode...it was verified by itunes and all that..but in the end it again said that iphone has some problem and can not function right now.
after that when ever i connect it with itunes, it gives the message, it can not activate the iphone further, try again later or contact customer service.
What to do now?????? Customer service people say..it is hardware problem

If it's a hardware problem, then the phone will need to be replaced.
There is no magic that can fix a hardware problem.

VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction id in results:

Subject: VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction
id in results:
Hello All,
I am facing the following error while running a loadtest (when i choose the scenario to be executed for No of test iterations). But the same loadtest with the Run duration for X minutes is running fine without any issues.
Any suggestions on the issue i am facing
error is :
could not read result repository: unknown transaction id in results:
or
could not read result repository: unknown request id in results:
Thanks
Satish

Hi Kotapati,
>>Subject: VSTS loadtest error while running Loadtest with Runsettings as No of test iterations , ERROR is : could not read result repository: unknown transaction
id in results:
According to your description, you mean that when you run your load test using the Test Iterations way and then get the error message, am I right?
If yes, please you try to close the VS, and then open this VS again. Then clean your load test project/solution and then re-build it, run your load test again check this issue again.
In addition, I suggest you could try to create a new load test and then run it using Test Iterations way check if you get the issue for the specified load test or all load tests.
If possible, I suggest you could share me simple load test for us so that we will further help you.
You could upload your load test to OneDrive and then copy link here.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

I am trying to import cr2files from the camera into lightroom 5 and keep getting an error message saying Lightroom can not read the files and therefore will not import them. Has anyone had a similar problem-.thanks

I am trying to import cr2files from the camera into lightroom 5 and keep getting an error message saying Lightroom can not read the files and therefore will not import them. Has anyone had a similar problem….thanks

If you are having the same problem, i.e. a disk permission problem, open your favorite search engine and search on, "change disk permissions", and I think you'll find plenty of information on how to fix the problem. This is a Lightroom forum. Your problem is with your operating system. There is no sense in rewriting instructions that are already available if you do a simple search.

I have a brandnew 7th gen classic ipad, it does not read in my itunes anymore. i bought it cause apple was suppose to be good, now i am lost as i just want my music, any help. tried the rec. steps to fix it and nothing

let em elaborate more, the unit is less than 5months old, i bought it just for music, i use to have a lot of cds, well it does not read anynore in my computer nor the itunes programe, i reset it, i put it to disk mode, i down loaded the newest itunes program, i want to know how to fix this as i paid apple good money for a product that died after 5months, for real.
this is bad business and i need some help

Does the iPod work okay otherwise apart from not being able to connect with and communicate with iTunes?
Have you tried connecting the iPod to another PC or Mac running iTunes to see if it is properly recognized there?
Is iTunes up to date on your PC? Does it appear in Device Manager when you plug it in? To access Device Manager, click start, right->click on Computer (or My Computer in Windows XP) and choose Manage. When the window opens, select Device Manager in the left hand pane if necessary.
Any unknown devices listed or does the iPod appear anywhere under USB Host Controllers?
B-rock

My PC is not reading my itunes music files, all I get is '!'

Hi, my computer recently crashed and I had to recovery the HDD and lose all my materials, but I still had all my itunes media on a separate drive. Anyway, I redownloaded itunes and now I added a folder of over 4800 songs, all either individual mp3 files or albums in folders. Now that all the albums are up (I lost a lot of the album covers too) I am having trouble playing music on itunes.
Whenever I click on most songs, I get a '!' saying that I have to now search for the file because it cannot be found. I have to search for EVERY song before it can find it. I have over 4800 songs, so I can't realistically search for EVERY ONE. Under 'Preferences' I went into "Advanced" and chose the folder where my songs would be read from. Yet still I have this problem. Funny thing is that it doesn't do it for EVERY song, but I would say about 90% of them. Why is my itunes not reading my files? I have the latest version of itunes on my PC and there is no problem with any of my mp3 files as they are all well and play fine on my ipod. The strange thing here is that all of my movies play just fine, I have 34 digital copy movies on my itunes. I have Windows 7.
Please help, this is a really annoying thing to deal with!

Since you mention PC, I'm guessing that you are referring to a Windows machine. If so, then see this support document. http://support.apple.com/kb/TS1538

Problem: this mac is not reading an excell file after upgrading to yosemite.   My Mac is from 2009, it use to work perfectly but it wasn´t able to open some apps, thats why i upgrade it.   Now it once i donwload the zip it appears with an ".ods" ext

Problem: this mac is not reading an excell file after upgrading to yosemite.   My Mac is from 2009, it use to work perfectly but it wasn´t able to open some apps, thats why i upgrade it.   Now it once i donwload the zip it appears with an ".ods" extension
i even already download a link
http://www.microsoft.com/en-us/download/confirmation.aspx?id=44026
which i read on another support page... but it doesnt allowed me to install it cause it says that i already have the disk of this program....
Im afraid to erase it and not being able to get it back...
What can i do!??
Thanks in advance for this kind answer!!!

fsolution wrote:
Problem: this mac is not reading an excell file after upgrading to yosemite...   Now it once i donwload the zip it appears with an ".ods" extension...
If the "it" refers to a compressed (zipped) spreadsheet that you downloaded, the ".ods" extension is used by LibreOffice and probably OpenOffice (which are free versions of MS Office) for spreadsheets, which would suggest that wherever you're getting that "Excel" file from has switched to one of those programs. I've tried opening an .ods file from LibreOffice using MS Office 2013 for Windows and it does open though with a warning that some things have been changed. I don't know if Office for Mac can normally open .ods files. But if your need is to just open .ods files, take a look at LibreOffice.

MacBook Pro (Retina, 15-inch, Mid 2014) will not read an SD card in the SDXC card reader. Does anyone know whats going on?

MacBook Pro (Retina, 15-inch, Mid 2014) will not read an SD card in the SDXC card reader. Does anyone know whats going on?

Hi David. I don't have as modern a Macbook Pro as you, mine is a 2012 model, but perhaps I can help. I often find that my SD card will not load when I first insert it. I have to remove it and then put it into the slot again firmly.
You also haven't posted any information about the SD card. What size is it, do you know how it is formatted, has it worked in that same mac previously, where did it come from, does it currently work in another device (such as your camera)? This sort of information will help to narrow down the problem.
If you post some more information I'm sure people will try to help you. In the meantime, if you look at your post again you should see "More Like This" at the bottom of the page and you may find an answer in some of those related posts.
Hope that helps.
Ivan

TS3694 My computerwill not read the lastest version of i tunes. i lost theold version how do i get it back to hold my music again???????help

My computer will not read the lastest version of i tunes ,i don;t know how to get the old version b. pleae help. i can't get my music back on my computer

what do you mean it will not "read" the latest version? you downloaded, installed, and nothing? it doesnt open?
does your computer meet the minimum requirements for itunes 11?

BarCode Not Reading

Similar Messages

Maybe you are looking for