Batch Job Problem

Hello,
I have a BDC Session created for sales order change delivery, PGI. It works good in fore ground. When I create a batch job for this report it is running into errors. Is there any change that I need to do in the BDC Sessions. Please Help me
Thanks
Viky

Hi!
Sometimes it occurs with BDC, when a warning message appears on the screen.
In foreground you simple press and enter, but in background it is going to stop.
You might try to enter into your code enter ok-codes (OK-CODE '/00'), on the dynpro there is a warning.
Regards
Tamá

Similar Messages

How to solve problem :- rep-188-Report Server acccepts only Batch jobs

How to solve problem :- rep-188-Report Server acccepts only Batch jobs
Report server :- 10gR1

Hello,
Could you give us some details about the command line ?
What is the value of DESTYPE ?
Regards

Problem in creating Batch job for programs in different servers.

Hi All,
I have a requirement like i have 2 different programs ( PRG1,PRG2 ) running in 3 different SAP servers (SER1,SER2,SER3).
I want to create a batch job for the programs.
Here When I run the PRG1 in Server SER1,it will create a file1 in SER1 as well as the other 2 servers (SER2 and SER3).
It just create a file and there is no content in the file.Once i start writing records to file1in SER1,the same record will be started writing in SER2 and SER3.This is using PRG1.
Once PRG1 will complete writing records in file,Next PRG2 will run in SER2 using file created by PRG1.
I want to create a batch job for PRG1.
How to trigger the PRG2 after completing job1 for PRG1 without any manual interaction.
Please help me for this.

Hi Ambili
You can set steps in these jobs in transaction SM36.
You can define that Job 2 starts after Job1 complete sucessfully and same game for other jobs.
Please, check attachment for detailed information about that
Kind regards
Edited by: Carlos Machado on May 27, 2010 6:01 PM

Display error message in batch job log

Hello
I have a batch job running and I have an error coming during some validation logic.
The problem is I need to continue the batch job when this error message comes and it should not cancel the batch job as it is doing currently but display that error message in batch job log, there are more similar error messages coming in job log and job gets finished, but when my error message comes job gets cancelled.
I cannot give it as info message as it will give wrong idea about message type.
Is there any FM by which we can add message in job log?

Sanjeev I have done that but problem is I do not want to give that as Information message but Error message only and continue processing.
If you see in screenshot 3rd message is given by me as information and you can see error messages also 6th and 7th and job continued till it is finished
Basically I want that 'I' to be displayed as 'E'.
Display error message in batch job log

Two Deliveries did not go through Batch Job Runing

Hi,
In this company every evening the automatic batch Job for Billing due list is run but on Nov 23 one Deliver and on Nov 30 another delivery has not gone through i.e. the invoices were not created for these two deliveries.
I checked in VF01, the individual invoice is being created. The user is asking the reason for this and how to prevent this type of situation in future.
I don't know the Batch Job number and I think it has been done in VF06.
Please guide me how I can solve this issue.
Thanks,
Jans

Hello Tushar,
Thank you for your reply. I don't know the Variant name also and I don't know the Batch Job number eirther. The user is not aware of these things. I tried to find out from VF06 but I could not figure out anything.
Please explain me your sentece "Execute billing program in foreground and check". you mean to say after creating the same scenario in the quality, I will run the Billing program ( I will take the Billing program from the VF01). If I am correct please let me know.
Regarding debugging, if I have to do how I can do it. I know to go to Debuggiing mode if I put in the command field "/h" , I will be in the debugging mode. But my question is which transaction Should I use VL02N or VF01 to find out the Problem
I have mentioned earlier that I went to VF01 and these deliveries are fine to create invoices but the User is interested to know the Problem and to find out the cause so that they can prevent it occuring in future.
Thanks,
Jans

Invoice not generated through Batch Job

Hello
I am facing a Problem in Batch Job. When the delivery is created through VL01n transaction manually, the Invoice for this delivery is created automatically. However for one of the delivery the Invoice was not created automatically through Batch Job.
Can some one help me how to go further on this problem? I have checked the Batch Job and found that it is schedule daily, However the Delviery was created after this schedule time. So ideally this delivery should have been considered for automatic generation of Invoice in the next schedule run of the Batch Job. However this has not happened.
Any views on this
Regards
Screams

Hello,
Please check the billing date and the billing date which is in the variant. in the variant there could be that the billing date might have been specified from and to, in any case billing date for the document is not past the variant billing date it will pick up.

How to find out batch job failure and taking action:

Normally We will monitor the batch jobs through transaction code sm37 for job monitoring. In SM37 we will give a batch job name date and time as input. In the first step we will check the batch job for the reason failure or check the spool request for the batch job for failures an help in analyzing the error
I understand from the my experience is that the batch may fail due to below reasons.
1.,Data issues : ex: Invalid character in quantity (Meins) field >>>> We will correct the corresponding document with correct value or we will manually run or request the team to rerun the batch job by excluding the problematic documents from the batch job variant so that it may process other documents.
2.Configuration issues : Materials XXXX is not extended for Plant >>>> we will contact the material master team or business to correct the data or we will raise sub contract call with support team to correct he data. Once the data been corrected and will request the team to rerun the batch job.
3.Performance issues : Volume of the data being processed by the batch job ,network problems.>>>Normally these kind of issues we will encounter during the month end process as there will lot of accounting transactions or documents being posted business hence it may cause the batch job failure as there is enough memory to complete the program or select queries in the program will timeout because of volume of the records.
4.Network issues. : Temporary connectivity issues in other partner systems :Outage in other partner systems like APO or other system like GTS will cause the batch job failure as Batch job not in position to connect other system to get the inforamtion and proceed for further steps.Nornmally we will check RFC destination status by running a custom program weather connectivity between system are in progress or not. then intimate other partner system for the further actions, Once the partner system comes online then we will intimate the team to restart or manually submit batch job.
Some times we will create a manual job by transaction code SM36.

I'm not sure what the question is among all that but if you want to check on jobs that are viewable via SM37 and started via SM36. The tables are TBTCP -Background Job Step Overview and TBTCO - Job Status Overview Table.
You can use the following FM to get job details:
GET_JOB_RUNTIME_INFO - Reading Background Job Runtime Data

Batch job failing with INVALID_STARTDATE exception

Hello Experts,
our batch job runs 17th minute of every hour on daily basis.It is running successfully from 00:17 AM to 20:17 PM and gets completed within 1 hour for every run.
But when it is starting 21:17PM, it keeps on running for next 5-6 hours and then gets cancelled with error "Invalid_startdate"
Currently it is posting all the idocs.Idoc status is 53. But the problem is closing the job Function module JOB_CLOSE is throwing an exception "INVALID_STARTDATE" and gets cancelled.
Could anyone please provide us any help on this.

Usually this message is raised because of:
Unsupported combinations of specifications, such as periodic repetition of jobs that were scheduled to wait for a predecessor job
Incomplete or incorrect specifications, such as an incomplete start date.
but..is your SAP in a time zone 3 hours different from yours?
e.g. New York has already a new day when you have 9PM in LA

Launch batch job thru SOAP call : no execution, connection OK.

Hello,
I am experiencing some problems launching batch jobs thru Web Services. I have added batch job "EPN_Test_Webservices" to the Web Services and enabled the Job Attributes.
When I try to launch the job thru a SOAP call, I get a reply but the job is not executed.
This is the SOAP envelope:
<SOAP-ENV:Envelope xmlns:SOAP-ENV="http://schemas.xmlsoap.org/soap/envelope/" xmlns:SOAP-ENC="http://schemas.xmlsoap.org/soap/encoding/" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
     <SOAP-ENV:Body>
          <m:EPN_Test_Webservices_Job xmlns:m="http://www.businessobjects.com/DataIntegrator/ServerX.xsd">
               <job_parameters>
                    <job_system_profile>String</job_system_profile>
                    <sampling_rate>10</sampling_rate>
                    <auditing>true</auditing>
                    <recovery>true</recovery>
                    <job_server>JS_ict</job_server>
                    <trace>String</trace>
               </job_parameters>
          </m:EPN_Test_Webservices_Job>
     </SOAP-ENV:Body>
</SOAP-ENV:Envelope>
This is the reply I get:
<soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
     <soapenv:Body>
          <BatchJobResponse>
               <pid>3888</pid>
               <cid>13</cid>
          </BatchJobResponse>
     </soapenv:Body>
</soapenv:Envelope>
When I use the "ping" operation I get the following reply:
<soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/" xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
     <soapenv:Body>
          <pingVersion>
               <version>Business Objects Data Integrator Version 11.7.2.0</version>
          </pingVersion>
     </soapenv:Body>
</soapenv:Envelope>
...which indicates the connection works. Also the "processed counter" increases, but the job does not get executed. There is nothing in the job log, there is no result (the job is supposed to write a record in a database table). What can be wrong?

If I run the following (on the machine I'm trying to set up the share)
smbclient -L localhost -U%
I got the following output
Connection to localhost failed (Error NT_STATUS_CONNECTION_REFUSED)
so I thought it might be something incorrect with the iptables side of things, however I haven't really touched that at all and it seems to look correct
iptables -nvL
Chain INPUT (policy ACCEPT 667 packets, 79977 bytes)
pkts bytes target prot opt in out source destination
Chain FORWARD (policy ACCEPT 0 packets, 0 bytes)
pkts bytes target prot opt in out source destination
Chain OUTPUT (policy ACCEPT 157 packets, 20724 bytes)
pkts bytes target prot opt in out source destination
So from my (very little) knowledge this appears correct (I think)... However it appears that something is blocking access somewhere.

Can U set breakpoint within a batch job and look at variables?

Hello friends,
I am trying to solve a problem that occurs within a program / transaction which can only be executed in background. The transaction in question is FPCOPARA and apparently this program cannot be executed in foreground.
If I understand well, we cannot set breakpoints within a background job and as a result we cannot inspect variable etc. during job execution. So the question is how to achieve the same goal within a batch job? How did you do it? As this is a standard SAP transacrtion, no program modification can be applied.
Your help is greatly appreciated.

Hi......
After u have executed ur batch job..
go to sm37 >>select ur job using checkbox>>enter 'JDBG' in transaction box and press enter
now debugger will start ..initial it will go through system code..after after a while the debugger will reach to your code and den you can debug the remaining report....
all the best
regards
vivek

How to get batch job o/p in PDF format and automatically saved to xyz loc

Hi Experts,
Our requirement is we want output of background job in PDF format and this PDF generated should be saved in some xyz path at OS level.
Why doing this?: Business don't want hard copy o/p of some batch jobs but only want to save this output in pdf format to some OS location for future use.
We could achieve above objective by archiving method (but for some reason we cant adopt it).
So guys please propose solution in detail regarding above problem "how to get o/p in PDF format and automatically get saved to xyz location"
System : 4.0B
OS : Windows NT
Database : Oracle
Thanks in advance

Hi guys,
Thanks guys for your invaluable advise.I asked abaper to use the above report for pdf conversion. But I have another problem that o/p of batch job should come in japanese language but when i check spool or hard copy o/p its not coming in readable form (seems something like machine language) . I dont what is the reason there must be some basis setting to get the batch job o/p in japanese language.
Please help me.
thank you

Run_report_object in forms10g: Reports Server only accept batch jobs

Hi all,
We've migrated an old forms application to forms 10g R1. To run report objects from the form applications, I use the following code to run reports with a report server (10g):
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_FILENAME,'c:\path\to\report.rep'');
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_EXECUTION_MODE,BATCH);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_COMM_MODE,ASYNCHRONOUS);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_DESTYPE,CACHE);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_DESFORMAT,'PDF');
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_SERVER,'repserver');
l_rep_return := RUN_REPORT_OBJECT(l_rep_id, pl_id);
The parameter pl_id is a pre-filled parameter list, and the parameter l_rep_id is the report_object, which was added to the reports-node in the fmb.
By running this code, the reportserver successfully executes the report and via the report server queue I can open the created PDF file.
But, as the report_comm_mode is set to ASYNCHRONOUS, the code doesn't wait until the reportserver has finished the execution of the report, so it's impossible to show the report by web.show_document. So I've set the report_comm_mode to SYNCHRONOUS:
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_FILENAME,'c:\path\to\report.rep'');
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_EXECUTION_MODE,BATCH);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_COMM_MODE,SYNCHRONOUS);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_DESTYPE,CACHE);
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_DESFORMAT,'PDF');
SET_REPORT_OBJECT_PROPERTY(l_rep_id,REPORT_SERVER,'repserver');
l_rep_return := RUN_REPORT_OBJECT(l_rep_id, pl_id);
But when I executes this code, the execution of the report failes, and the following error code is shown in the report server queue:
Terminated with error: REP-188: Reports Server only accept batch jobs
But as you can see, the execution_mode is set to BATCH, so that is not the problem.
Is there anyone who can help me to fix this problem?
Regards,
Jeroen

I just sent you an e-mail, I hope it helps!

Error in Batch Job - Urgent

Hi,
Iam getting a Error
" Error returning from function G_SET_FETCH,returncode 3"
in a particular batch job, when i tried to understand where it arised from i found its from a Standard SAP program LSHL2F05 and if the FM 'HELP_VALUES_GET_NO_DD_NAME' Fails, This Error Occurs.
How to correct this Error???
Regards,
Anita

Hi All,
Thank You very Much for your response.
I checked GS02 Transaction which is used to maintain SET ID's. The User entered the wrong SET ID and that was the problem. Now , Its fine.
Rich, Thanks for turning my attention to SET ID. I was not looking at it at all and was looking at the Job log error message rather.
Thank you Everyone.
Regards,
Anita

Is there a way to access ABAP OO instances from a batch job report

Hello,
I am looking for a way to access ABAP OO instances from a batch job report. My circumstances are the following:
I have got some ABAP OO coding that identifies other objects (class instances) that have to be processed (they have a DoIt method that does some calculation). As this processing is time consuming and performace relevant I have to parallelize this in batch jobs. This batch jobs however can only be "simple" ABAP reports according to SM36. The problem is now that I dont really know how to tell the batch job report what objects to process. Somehow I have to access theses instances from that batch job report.
Does anybody have an idea?
Greetings
Matthias

Hi David,
thanks a lot for your help. After a lot of searching on the net this seems to be the only way to cope with it. However I am not sure about the locking mechanisms and if its suitable for mass data processing. In the help page you suggested the following is stated which I do not fully understand::
"The current lock logic does not enable you to set specific locks for the following requirements:
·        Many parallel read and write accesses
·        Frequent write accesses
·        Division into changeable and non-changeable areas
Although the lock logic makes the first two points technically possible, they are not practical because most accesses would be rejected."
Does this mean
a) if I dont want to set "specific locks" for frequent write accessess I am fine
or
b) I am discouraged from use shared memory technics for frequent write accessess?
In the latter case I will have a problem...
What do you think?
Greets
Matthias

Spool not getting created in batch job

Hello experts,
We have a requirement of printing BA00, BA01 and LD00 from different application.
We have done same code for all BA00, BA01, and LD00.
Normally the code is working fine except in few cases, when batch job is created but spool is not created.
DATA: job_name TYPE tbtcjob-jobname,
              number   TYPE tbtcjob-jobcount,
              print_parameters TYPE pri_params,
              wv_pripar    TYPE pri_params,
              wv_arcpar    TYPE arc_params,
              wv_val       TYPE c VALUE 'X',
              wv_false     TYPE c VALUE 'X',
              gv_mandt     TYPE tsp01-rqclient,
              gv_user      TYPE tsp01-rqowner.
          CLEAR: gv_mandt, gv_user, number.
          gv_mandt = sy-mandt.
          gv_user = sy-uname.
          job_name = 'DELIVERY_PRINTING'.
          CLEAR: range1.
          range1-sign = 'I'.
          range1-option = 'EQ'.
          range1-low = 'LD00'.
          CLEAR: range1-high.
          APPEND range1 TO range.
          CALL FUNCTION 'JOB_OPEN'
            EXPORTING
              jobname          = job_name
            IMPORTING
              jobcount         = number
            EXCEPTIONS
              cant_create_job = 1
              invalid_job_data = 2
              jobname_missing = 3
              OTHERS           = 4.
          IF sy-subrc = 0.
            SUBMIT sd70av2a WITH rg_kschl IN range
                            WITH rg_vbeln IN deli_tab
                            TO SAP-SPOOL
                          SPOOL PARAMETERS print_parameters
                          WITHOUT SPOOL DYNPRO
                          VIA JOB job_name NUMBER number
                          AND RETURN.
            IF sy-subrc = 0.
              CALL FUNCTION 'JOB_CLOSE'
                EXPORTING
                  jobcount             = number
                  jobname              = job_name
                  strtimmed            = 'X'
                EXCEPTIONS
                  cant_start_immediate = 1
                  invalid_startdate    = 2
                  jobname_missing      = 3
                  job_close_failed     = 4
                  job_nosteps          = 5
                  job_notex            = 6
                  lock_failed          = 7
                  OTHERS               = 8.
              IF sy-subrc <> 0.
              ENDIF.
            ENDIF.
            WAIT UP TO 10 SECONDS.
** to give the data to the printer***
*            CLEAR gv_rqident.
            SELECT SINGLE listident INTO gv_listident FROM tbtcp
                          WHERE jobname = job_name
                           AND jobcount = number.
          IF sy-subrc = 0.
            MOVE gv_listident to gv_rqident.
            CALL FUNCTION 'RSPO_OUTPUT_SPOOL_REQUEST'
              EXPORTING
                spool_request_id = gv_rqident.
          ENDIF.
The same code is for all the output BA00, BA01 and LD00.
The issue is that for few batch jobs (which is created in the above code) , spool is not getting created.
Thanks and Regards,
Paritosh Pandey

Hi,
The code starting from WAIT UP TO 10 SECONDS. - not only does it look attrocious, is error prone (if no free process for executing batch job is available for 10 seconds, or if the job runs for more than 10 seconds, what will happen...?), but seems utterly unnecessary... Is there any reason immediate spool output can not be handled by simply setting PRINT_PARAMETERS-PRIMM = 'X'?
cheers,
Janis
Edit in:
Ok, i just read Document in spool but not printed... Do not use an output device relying on frontend access methods to do printing from background processing. Frontend is not available during background processing, period. To my knowledge there is no easy, clean solution to this problem other than defining and assigning, per user, output devices not relying on frontend printing. What if the dialog user has logged off by the time batch job finishes..? May the spool remain unprinted?
Has the SAP Basis refused to define output devices (I have hard time believing this...)? Well, tell them one time to stop being silly and if they do not cooperate, tell the owner of the requirement that it can not be implemented due to uncooperative Basis then... and that the users will have to keep going to SP01 and manualy start the output!
Message was edited by: Jānis B

Batch Job Problem

Similar Messages

Maybe you are looking for