Battery status stuck at 99%

So i have had my aluminum macbook for about 2 weeks or so and it has been plugged in for about the entire time(desktop replacement) and now i have noticed that the battery status has be stuck at 99%. Any tips?

Hi Joshua Conecoff: That is perfectly normal behaviour. Check out this Apple article for more details. http://support.apple.com/kb/TS1909
Enjoy
Stedman

Similar Messages

Macbook pro 17" 3g battery status indicator stuck on 100%

Battery status indicator stuck on 100% Worked normaly until today
resetting smc does not help
Battery Information:
Model Information:
Serial Number:          9G95201YS4M0A
Manufacturer:          DP
Device name:          bq20z951
Pack Lot Code:          0000
PCB Lot Code:          0000
Firmware Version:          0042
Hardware Revision:          0001
Cell Revision:          0119
Charge Information:
Charge remaining (mAh):          65262
Fully charged:          Yes
Charging:          No
Full charge capacity (mAh):          65262
Health Information:
Cycle count:          221
Condition:          Replace Now
Battery Installed:          Yes
Amperage (mA):          -1629
Voltage (mV):          8072

I closed the lid for about 10 minutes to do something and when I came back the status seemed to be working correctly (80%) and the health now seems normal. I made no other changes. I will keep an eye on it and post if it goes haywire again. Thanks for your help
Battery Information:
Model Information:
Serial Number:          9G95201YS4M0A
Manufacturer:          DP
Device name:          bq20z951
Pack Lot Code:          0000
PCB Lot Code:          0000
Firmware Version:          0042
Hardware Revision:          0001
Cell Revision:          0119
Charge Information:
Charge remaining (mAh):          9833
Fully charged:          No
Charging:          No
Full charge capacity (mAh):          12217
Health Information:
Cycle count:          221
Condition:          Normal
Battery Installed:          Yes
Amperage (mA):          -1550
Voltage (mV):          7930

The battery status is stuck in 15% in my Acer Iconia One. Charges normally. It is preventing update.

The battery status is stuck in 15% in my Acer Iconia One. Charges normally. It is preventing update.Can someone help me?

You can try 2 things: 1) let it discharge completly, then plug the AC charger without turn the tablet on and leave it until if finish charging, then power it on and check if battery charge is correct 2) do a factory reset (backup you data before doing it). settings/backup&reset - factory data reset

Battery Status Indicator (in menu bar) does not update

I've recently noticed that the battery status indicator in the menu bar gets "stuck," and won't update. I can force it to update by disabling and re-enabling it, or by changing the view style, but if I leave it alone, it won't change, even across sleep/wake cycles.
Any ideas?

Actually, the problem disappeared after a reboot. I reboot so infrequently, I didn't even consider that as a solution, but something else caused me to need to reboot, and after that, the indicator works fine.
Still no idea what caused it to get stuck in the first place, but for now, it's better.
Good luck!

Excite Pro - Battery Status Indicator at 0%

Battery status indicator is stuck at 0% - battery holds charge ok just don't know what it is. I presume the battery stats file is corrupted - is the only way to fix it a factory reset?
Calibration either needs root - not possible or 60% charge - won't work as says 0%!!!!

I think you should set it to factory settings.
Press and hold power button and volume up button. Then in the menu choose factory reset.
If this will not work, then the issue must be related to hardware failure

ThinkPad X300 battery charging stuck at 99%

Dear Community!
I have a problem with my Lenovo ThinkPad X300 computer. The battery charging stuck at 99% (remaining capacity about 69% and 300 cycles). The Power Manager displays, the battery is at 100% but "status" periodically changes - both Power Manager and Windows battery indicator - between "No activity" and "Charging".
Every time stuck at the same "Remaining capacity". As i noticed durin battery user windows and the Power Manager displays differet informatioun about the remaining battery level and time.
I wish you can help me.
(Fresh installed Windows 7 Professional 64-bit)
Thanks!
(Here is a picture about my problem. At the windows dialog "csatlakoztatva, töldőtik" means "plugged in and charging" - my windows is hungarian located.)
Link to image
mobal,
Moderator note: images totalling more than 50k converted to links per forum rules: Lenovo Community Participation Rules
Solved!
Go to Solution.

Hi Mobal,
When you say "always on", is it green and flashing or green and always on? Solid green (not blinking) means fully charged and not charging. And I think the Windows Power indicator would be the more accurate of the two.
Refer the article and see if it helps!
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

How to reset battery status in menu bar?

After upgrading to 10.5.5 I experienced sudden loss of performance with both of my batteries.
Overnight the battery yielded only 45 min, and the recharge time was usually about 40 min as well.
As a result of frustration, I decided to crack open the case of 1 battery and connect a 12V 20W bulb to fully discharge the battery.
Possibly as a result of the deep discharge, the battery took 6 hrs to recharge, and now yields approx 3-4 hrs of power.
HERE IS THE PROBLEM. The battery status in the menu bar does not seem to reflect the battery's newly found performance.
It keeps says "40 min." left, and when it runs out of minutes, it displays: "Calculating ... remaining"
The same odd behaviour occurs when charging the battery. It says: "35 min" to full charge, and when it runs out of minutes it displays: "Battery finishing charging"
MOREOVER, yesterday, the low level power indicator appeared, but the computer kept working for another 1.5 hrs before going to sleep.
Finally the System profiler shows this information
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 1661
Remaining Capacity (mAh): 1361
Amperage (mA): -1203
Voltage (mV): 11441
Cycle Count: 71
After the deep discharge, the Full Charge capacity jumped form 640 to 1661.
That's good, isn't it?
But how can I reset the battery status in the menu bar to reflect the actual performance of the
battery? Or did the deep discharge damage something?
Regards

I talked to Apple repeatedly and they refused to replace the battery in spite of the many good arguments I brought forward. Their only argument is that the battery is old (was shipped in 2006)
I even requested them to ask their own technicians whether
it is normal for a battery with only 71 cycles to discharge so soon.
My request was declined.

Storage 6180 - Both controller Battery status is Learning

I have face the problem in 6180, battery not charging. So i have reset the controller. After reset the controller, controller battery is charged and alarm is cleared. But both controller battery status is showing learning. Kindly suggest.
regards,
Anwar

user13590162 wrote:
I have face the problem in 6180, battery not charging. So i have reset the controller. After reset the controller, controller battery is charged and alarm is cleared. But both controller battery status is showing learning. Kindly suggest.
regards,
AnwarA non authorative 'guess' is that the controller is attempting to learn the rate of discharge of the battery. It needs a little time (maybe quite a few hours, even a day) to do this.
Batteries are a weak spot of things.
Get prepared to replace the battery .... otherwise I suspect (and I know not the 6180 specifically and I am not bothered to look it up, you can as well as I), the appliance may degrade and run a little slower.

HP Battery status changed from "Weak" to "Replace"....

Hi,
I had purchased HP Laptop dv4-1211 TU in India in 2009. Now i stay in US. Recently few days back, i checked a option " HP Battery Check" in my laptop. When clicked it said my battery status is "Weak". I didn't bother much. But today when i checked it back it said " Replace". How do i go about this?
My queries are:
1. Is it safe to use my laptop in this condition?
2. Battery gets heated up too much after this, so do i need to replace with a new one or can i plug in and use it, i.e i meant on AC power and not battery alone?
Waiting for the response from u.... pls help me....

Hi sweety2222!: most laptops that use batteries can also use AC as well
but to be sure I'd check the manual the manual will also tell you if you can replace it, the type of battery & how to replace it as well
good luck
hope this helps you
spacechild

After updating to ios 8.0.2 .when i'm unlocking the mobile wallpaper dont display . its shows only network and battery status .

after updating to ios 8.0.2 .when i'm unlocking the mobile wallpaper dont display . its shows only network and battery status .
then i need to switch off and switch the iphone. per day i'm doing this for 3 times.
mean while if some one calls ,its not displaying who is calling.
need to rectify this ASP

Hi Tarun 49,
If you are having issues with your iPhone such as you describe, you may want to try some things to troubleshoot.
First, quit all running applications and test again -
iOS: Force an app to close
Next, I would try restarting the iPhone -
Turn your iOS device off and on (restart) and reset
If the issue is still present, you may want to restore the iPhone as a new device -
iOS: How to back up your data and set up your device as a new device
Thanks for using Apple Support Communities.
Best,
Brett L

Battery status won't hit 100% anymore

I've had my PB about a month and a half (got it new believe it or not) and recently I noticed that even though the battery status will say "charged", the percentage will not show 100% when plugged in. At first it was 99% and now it's 97%. I've calibrated my battery and try to let it run fully down every once in a while.
The battery info in profiler shows this:
Full Charge Capacity (mAh): 5309
Remaining Capacity (mAh): 5183
Is this normal or should I be concerned or what?
Thanks everyone.

That doesn't sound out of the ordinary. See this Apple note: http://docs.info.apple.com/article.html?artnum=88344

Missing Blackberry Battery Status Indicator

I've looked all over the web, my instruction manual, the index inside the phone, and in still cannot find the meaning of this symbol in the middle of my battery bar. From what I've seen on the internet, its as almost as if it does not exist. I would probably believe so if it was not for the fact that I am staring at it right now as I type this. I have had problems with the USB port on it before and I am pretty sure that has something to do with it. Also when Its plugged into the computer and the port and USB are finally working in unison, the computer says that it is malfunctioned.
The icon appears when I've tried to connect to it to a computer or even sometimes to an outlet. It looks like a C or parentheses with a scrunched up 3 sort of like this:
C 3
or
( 3
I was surprised that no one else has seen or inferred about this icon and even more surprised that a complete index of all battery status indicators would exist; including those for malfunctioned or damaged batteries. Any help or recommendations to help me solve this problem is greatly appreciated.

Hi silvaback75
Can you send us a picture of this icon?
Thanks
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

[solved] show battery status in PS1 not working correctly (script)

Hey,
I got this script to show the battery life of my laptop in my PS1:
#!/bin/bash
BATTERY=/sys/class/power_supply/BAT1
REM_CAP=`cat $BATTERY/energy_now`
FULL_CAP=`cat $BATTERY/energy_full`
BATSTATE=`cat $BATTERY/status`
CHARGE=`echo $(( $REM_CAP * 100 / $FULL_CAP ))`
NON='\033[00m'
BLD='\033[01m'
RED='\033[01;31m'
GRN='\033[01;32m'
YEL='\033[01;33m'
COLOUR="$RED"
case "${BATSTATE}" in
'Charged')
BATSTT="$BLD=$NON"
'Charging')
BATSTT="$BLD+$NON"
'Discharging')
BATSTT="$BLD-$NON"
esac
if [ "$CHARGE" -gt "99" ]
then
CHARGE=100
fi
if [ "$CHARGE" -gt "30" ]
then
COLOUR="$GRN"
fi
if [ "$CHARGE" -gt "15" ]
then
COLOUR="$YEL"
fi
echo -e "${COLOUR}${CHARGE}%${NON} ${BATSTT}"
I made it executable: chmod +x /home/kanikuleet/scripts/battery_status.sh
Put this in my .bashrc file: PS1="[ \$(/home/kanikuleet/scripts/battery_status.sh) ] \u@\h:\w \$ "
Built it: source ~/.bashrc
Now I get this errors:
/home/kanikuleet/scripts/battery_status.sh: Line 30: [: echo $(( $REM_CAP * 100 / $FULL_CAP )): integer expression expected
/home/kanikuleet/scripts/battery_status.sh: Line 35: [: echo $(( $REM_CAP * 100 / $FULL_CAP )): integer expression expected
/home/kanikuleet/scripts/battery_status.sh: Line 40: [: echo $(( $REM_CAP * 100 / $FULL_CAP )): integer expression expected
My bash promt currently looks like this:
[ echo $(( $REM_CAP * 100 / $FULL_CAP ))% ] kanikuleet@arch: ~ $
I have acpi installed and BAT1 is my battery, I checked it.
Can anyone help??
Last edited by kanikuleet (2012-12-28 22:21:10)

kanikuleet wrote:Works! Thank you
In that case, please mark your thread as [solved] by editing the title of your post.

Nokia e7 - belle update battery status

Hi
i upgraded my nokia e7 to nokia belle recently and I was very excited but after the update I found out that there no longer was a battery status showing the percentage left. I really liked the old battery status so you would know how much battery life is left. It is just a bit weird that a very good thing from the previous version is discontinued on the belle version. I'm sure many others would agree with me on this..
Solved!
Go to Solution.

the battery level in the new structure has the same 7 levels... you can check it out just like that... not necessarily you would need a visible info on the battery level
anyways
All 7 parts filled up - 100%
6- 80%
5-65%
4-50%
3-35%
2-20%
1-10%

Default color is displayed for time, cellular and battery status‏‏

Hi all.
I'm using non-default background color for my page. Time, cellular, battery status have default color (system theme). How can I change this color?
I wrote in Page.xaml:
<Page
Background="#FFE5E9EC"
Foreground="#FF000000"
/>
But it doesn't work.
My example:
Skype example:

Set ForegroundColor property of StatusBar. Try following code
StatusBar statusBar = StatusBar.GetForCurrentView();
statusbar.ForegroundColor = Colors.Black;
https://msdn.microsoft.com/en-us/library/windows.ui.viewmanagement.statusbar.foregroundcolor.aspx
Gaurav Khanna | Microsoft .NET MVP | Microsoft Community Contributor

Battery status stuck at 99%

Similar Messages

Maybe you are looking for