Bluetooth device stopped working suddenly.

Hello,
My bluetooth controller was working till yesterday and stopped working suddenly today i am not sure what caused the problem, I use a bluetooth headset and when i tried to connect it today i saw that it was failing and when i tried to reboot the system then everything is gone, the logs seems to throw some strange errors. Please see my system configuration below.
Linux computergeek 3.18.6-1-ARCH #1 SMP PREEMPT Sat Feb 7 08:44:05 CET 2015 x86_64 GNU/Linux
I can see the bluetooth device in the "lsusb".
Bus 001 Device 003: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth
Also i can see the "btusb" module is loaded properly and I haven't upgraded my kernel recently.
But "hciconfig" and "hcitool" gives me below error and i cannot bring the hci0 interace up.
[root@computergeek]# hciconfig -a hci0
hci0: Type: BR/EDR Bus: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:3 acl:0 sco:0 commands:4 errors:1
Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
Packet type: DM1 DH1 HV1
Link policy:
Link mode: SLAVE ACCEPT
[root@computergeek]# hciconfig hci0 up
Can't init device hci0: Connection timed out (110)
[root@computergeek]# hcitool dev
Devices:
From Bluetooth control,
[root@computergeek]# bluetooth
bluetooth = on
[root@computergeek]# bluetoothctl
[bluetooth]# power on
No default controller available
[bluetooth]#
My "dmesg" output says this.
[ 4510.619589] Bluetooth: hci0 urb ffff8800ae373240 failed to resubmit (113)
[ 4510.619959] Bluetooth: hci0 urb ffff8800ae373300 failed to resubmit (113)
I tried every solutions on the other thread but nothing seems to help!
Any help would be greatly appreciated!!
Thanks
Last edited by vpraveenn (2015-02-17 21:05:16)

I have the same bluetooth controller (0cf3:3005, Atheros AR3011) on my laptop (ASUS K53SV) and have the exact same problem. Bluetooth works for a while until tx errors start showing up:
[24952.326871] Bluetooth: hci0 command 0x0c1a tx timeout
[24954.332842] Bluetooth: hci0 command 0x0c52 tx timeout
[24956.338826] Bluetooth: hci0 command 0x0c24 tx timeout
[24958.344882] Bluetooth: hci0 command 0x0405 tx timeout
[24993.806536] Bluetooth: hci0 command 0x0408 tx timeout
[25033.899824] Bluetooth: hci0 command 0x0408 tx timeout
[25048.548327] Bluetooth: hci0 command 0x0c14 tx timeout
[25051.014213] Bluetooth: hci0 command 0x0c14 tx timeout
[25075.805968] Bluetooth: hci0 command 0x0408 tx timeout
Resetting the bluetooth device works sometimes but not always. There is always a chance that the device will just become unresponsive to any kinds of commands:
# hciconfig hci0 reset
Can't init device hci0: Connection timed out (110)
I've tried various methods (block/unblock them with rfkill, `rmmod btusb` & `modprobe btusb`, etc) but none works after the device is "dead". The only way to recover seems to be powering off the laptop (simply rebooting doesn't fix the problem).
Last edited by PkmX (2015-02-18 14:55:38)

Similar Messages

All input devices stop working suddenly

Every now and then ALL input devices stop working,ths is not temporary - a forced shut down is needed
What happens is that I am happily working away when suddenly all input devices stop working with no warning, so the light goes off on my Wacom (Intuous 3) tablet, the keyboard and the apple trackpad are not responded to i.e. the cursor stays where it was on the screen prevously and I am left with the only option to restart by holding down the power button
any thoughts or similar experiences

If you don't already have a current backup, back up all data before doing anything else. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve your problem. The backup is necessary on general principle, not because of anything suggested in this comment.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The procedure will help identify which such modifications you've installed, as well as some other aspects of the configuration that may be related to the problem.
Don’t be alarmed by the seeming complexity of these instructions — they’re easy to carry out. Here's a brief summary: In each of two steps, you copy a line of text from this web page into a window in another application. You wait about a minute. Then you paste some other text, which will have been copied automatically, back into a reply on this page. The sequence is copy; paste; paste again. That's all there is to it. Details follow.
You may have started the computer in "safe" mode. Preferably, these steps should be taken while booted in “normal” mode. If the system is now running in safe mode and is bootable in normal mode, reboot as usual.
Below are instructions to enter UNIX shell commands. They do nothing but produce human-readable output. However, you need to think carefully before running any program at the behest of a stranger on a public message board. If you question the safety of the procedure suggested here — which you should — search this site for other discussions in which it’s been followed without any report of ill effects. If you can't satisfy yourself that these instructions are safe, don't follow them.
The commands will line-wrap or scroll in your browser, but each one is really just a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then copy it.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. Step 1 should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click anywhere in the line of text below on this page to select it:
PB=/usr/libexec/PlistBuddy; PR () { [[ "$o" ]] && printf '\n%s:\n%s\n' "$1" "$o"; }; PF () { o=$($PB -c Print "$2" | awk -F'= ' \/$3'/{print $2}'); PR "$1"; }; PN () { [[ $o -eq 0 ]] || printf "\n%s: %s\n" "$1" $o; };{ system_profiler SPSoftwareDataType | sed '8!d;s/^ *//'; o=$(system_profiler SPDiagnosticsDataType | sed '5,6!d'); fgrep -q P <<< "$o" && o=; PR "POST"; o=$(( $(vm_stat | awk '/Pageo/{sub("\\.",""); print $2}')/256 )); [[ $o -gt 1024 ]] && printf "\nPageouts: %s MiB\n" $o; o=$(kextstat -kl | grep -v com\\.apple | cut -c53- | cut -d\< -f1); PR "Loaded extrinsic kernel extensions"; o=$(launchctl list | sed 1d | awk '!/0x|com\.apple|org\.(x|openbsd)|\.[0-9]+$/{print $3}'); PR "Loaded extrinsic user agents"; o=$(launchctl getenv DYLD_INSERT_LIBRARIES); PR "Inserted libraries"; o=$(crontab -l); PR "User cron tasks"; o=$(cat /e*/lau*); PR "Global launchd configuration"; o=$(cat ~/.lau*); PR "Per-user launchd configuration"; PF "Global login items" /L*/P*/loginw* Path; PF "Per-user login items" L*/P*/*loginit* Name; PF "Safari extensions" L*/Saf*/*/E*.plist Bundle | sed 's/\..*$//;s/-[1-9]$//'; o=$(find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $ | wc -l); PN "Restricted user files"; cd; o=$(find -L /S*/L*/E* {,/}L*/{A*d,Compon,Ex,In,Keyb,Mail/Bu,P*P,Qu,Scripti,Servi,Spo}* -type d -name Contents -prune | while read d; do ID=$($PB -c 'Print :CFBundleIdentifier' "$d/Info.plist"); ID=${ID:-No bundle ID}; egrep -qv "^com\.apple\.[^x]|Accusys|ArcMSR|ATTO|HDPro|HighPoint|driver\.stex|hp-fax|JMicron|microsoft\.MDI|print|SoftRAID" <<< $ID && printf '%s\n\t(%s)\n' "${d%/Contents}" "$ID"; done); PR "Extrinsic loadable bundles"; o=$(find /u*/{,*/}lib -type f -exec sh -c 'file -b "$1" | grep -qw shared && ! codesign -v "$1"' {} {} \; -print); PR "Unsigned shared libraries"; o=$(system_profiler SPFontsDataType | egrep "Valid: N|Duplicate: Y" | wc -l); PN "Font problems"; for d in {,/}L*/{La,Priv,Sta}*; do o=$(ls -A "$d"); PR "$d"; done; } 2> /dev/null | pbcopy; echo $'\nStep 1 done'
Copy the selected text to the Clipboard by pressing the key combination command-C. Then click anywhere in the Terminal window and paste (command-V). I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
The command may take up to a few minutes to run, depending on how many files you have and the speed of the computer. Wait for the line "Step 1 done" to appear below what you entered. The output of the command will be automatically copied to the Clipboard. Paste into a reply to this message. No typing is involved in this step.
Step 2
Remember that you must be logged in as an administrator for this step. Do as in Step 1 with this line:
PR () { [[ "$o" ]] && printf '\n%s:\n%s\n' "$1" "$o"; }; { o=$(sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix\.cron)|org\.(amav|apac|calendarse|cups|dove|isc|ntp|post[fg]|x)/{print $3}'); PR "Loaded extrinsic daemons"; o=$(sudo defaults read com.apple.loginwindow LoginHook); PR "Login hook"; o=$(sudo crontab -l); PR "Root cron tasks"; o=$(syslog -k Sender kernel -k Message CReq 'GPU |hfs: Ru|I/O e|find tok|n Cause: -|NVDA\(|pagin|timed? ?o' | tail -n25 | awk '/:/{$4=""; print}'); PR "Log check"; } 2>&- | pbcopy; echo $'\nStep 2 done'
This time you'll be prompted for your login password, which you do have to type. Nothing will be displayed when you type it. Type it carefully and then press return. You may get a one-time warning to be careful. Heed that warning, but don't post it. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: Step 2 might not produce any output, in which case the Clipboard will be empty.
You can then quit Terminal.
To prevent confusion, I'll repeat: When you type your password in the Terminal window, you won't see what you're typing.
Note: If you don’t have a login password, set one before taking Step 2. If that’s not possible, skip the step.
Important: If any personal information, such as your name or email address, appears in the output of these commands, anonymize it before posting. Usually that won't be necessary.
Remember, Steps 1 and 2 are all copy-and-paste — type only your password. Also remember to post the output.

Bluetooth device stopped working

hey,
i was wondering if anyone could help me ???
in windows, my bluetooth stopped working all of a sudden it can't find anything and no other devices can see it's look like the device has been switch off.
btw i'm using snow leopard and i just installed windows vista Ultimate.
and it's driving me insane just when i got the drivers working (the sound, the trackpad , ... ) this happened

I have the same bluetooth controller (0cf3:3005, Atheros AR3011) on my laptop (ASUS K53SV) and have the exact same problem. Bluetooth works for a while until tx errors start showing up:
[24952.326871] Bluetooth: hci0 command 0x0c1a tx timeout
[24954.332842] Bluetooth: hci0 command 0x0c52 tx timeout
[24956.338826] Bluetooth: hci0 command 0x0c24 tx timeout
[24958.344882] Bluetooth: hci0 command 0x0405 tx timeout
[24993.806536] Bluetooth: hci0 command 0x0408 tx timeout
[25033.899824] Bluetooth: hci0 command 0x0408 tx timeout
[25048.548327] Bluetooth: hci0 command 0x0c14 tx timeout
[25051.014213] Bluetooth: hci0 command 0x0c14 tx timeout
[25075.805968] Bluetooth: hci0 command 0x0408 tx timeout
Resetting the bluetooth device works sometimes but not always. There is always a chance that the device will just become unresponsive to any kinds of commands:
# hciconfig hci0 reset
Can't init device hci0: Connection timed out (110)
I've tried various methods (block/unblock them with rfkill, `rmmod btusb` & `modprobe btusb`, etc) but none works after the device is "dead". The only way to recover seems to be powering off the laptop (simply rebooting doesn't fix the problem).
Last edited by PkmX (2015-02-18 14:55:38)

Bluetooth Device not working anymore...

Hi,
I had been using this thinkpad machine from 2010. Everything was workign fine. But I don't know what and where something went wrong. THE BLUETOOTH DEVICE STOPPED WORKING.
The light on the panel of machine turns off for a couple of seconds when the machine is turned on but after that the light is turned off and it never come back on unless or untill next start. (the light of BLUETOOTH device is turned on even before something appears on the screen).
When I try to install drivers it asks to check the device is connected properly etc, but neither I can install the driver nor it is useable.
Please help me.
thanks
Regards

Your Bluetooth device inside your computer seems to be turned off. Press Fn + F5 key and see if your Bluetooth Radio is turned on.

TS4323 Hi, I have a 13" MacBook Air and my bluetooth stopped working suddenly, I receive this message: Bluetooth not available

Hi, I have a 13" MacBook Air and my bluetooth stopped working suddenly, I receive this message: Bluetooth not available

Hey csamuelnguma,
Thanks for your post, and welcome to the Apple Support Communities.
I understand that your MacBook Air's bluetooth is no longer functioning correctly. I recommend that we start by resetting both the SMC and PRAM:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
OS X Mountain Lion: Reset your computer’s PRAM
http://support.apple.com/kb/PH11243
Note: Resetting PRAM may change some system settings and preferences. Use System Preferences to restore your settings.
Thanks,
Matt M.

NB520 - Wifi stopped working suddenly on its own

Hi,
I bought my NB520 in Singapore.
The WIFI was working properly for almost 3 years until recently I have this strange problem.
It stopped working suddenly on its own last June for almost 2 weeks.
Just when I was about to send it to the repair centre, it came back on again.
But the WIFI comes on and off for a few more weeks before it stabalised.
It works ok ever since, until 3 days ago it went off again like the last time.
Usually, when I switch on the netbook, the WIFI indicator (red light) will come on within seconds.
To use Bluetooth, I just right click on the Bluetooth icon and press "Enable Bluetooth Function" and Bluetooth will turn on.
But now when I do that, it tells me to "Plug in Bluetooth device".
Is this a hardware or software problem ?
I spoke with a local technician but she is unsure too.
Would appreciate if you can help me with this problem. Thanks in advance.
Regards,
Fionna

> Is this a hardware or software problem ?
This can be answered very easily recovering the notebook back to factory settings.
But I guess this is not an option for you at this time. Isnt it?
However, the issue you are talking in your post looks like the WLan isnt enabled and chosen properly.
Usually you can use the FN + F8 key combination to enable and disable the WLan and BT module.
Pressing both keys would switch between WLan and BT as well as disable and enable the modules.
Did you test this in the past?
In case the FN + F8 would not work as it should, I would recommend you to download the Wlan driver from Toshiba page released for this notebook series and to reinstall the Wlan driver.
Your feedback would be greatly appreciated.

Bluetooth Mouse stops working after software updates

Hello,
I've been using a Bluetooth mouse with my X220 Tablet for several months now. After fiddling with device manager to ensure that the Thinkpad Bluetooth device does not have the "Allow the computer to turn off this device to save power" setting set, things were working perfectly.
However, after running through some windows & Lenovo updates, the mouse now seems to work for a while, but after any idle time, the mouse stops working. Turning the mouse off & back on seems to cause it to reconnect, and it works until the next time it goes idle for 2 minutes.
I've gone through device manager, and made sure both the Bluetooth & USB Root devices are set not to power down (per http://forums.lenovo.com/t5/X-Series-ThinkPad-Laptops/Bluetooth-mouse-stops-working-from-time-to-tim... ), but still no luck.
The software updates applied from the Lenovo System Update tool were:
ThinkPad Power Management Driver: 1.67.04.05
ThinkPad Power Manager: 6.64.4
Lenovo Solution Center: 2.4.002
Intel G1/G2 Display Driver: 9.17.10.3347
Also, some windows updates which don't seem related (mostly security), but I can lookup the list of KB numbers if helpful.
Are there any known issues with the power manager updates that might affect this? If so, what's the best way to revert to the last working version?
Thanks!

Try doing a PRAM reset and see if that helps, also put in new batteries as that may make a difference.
OS X Yosemite: Reset your computer’s PRAM

I own a HP Pavilion dv6915nr, it stopped working suddenly.

Hello,
HP Pavilion dv6915nr.
Windows Vista home premium 32-bit.
I own a HP Pavilion dv6915nr, it stopped working suddenly last night. It was working perfectly, I was watching a video on HULU and I stepped away for 2 or 3 minutes, when I came back the screen was off. The laptop seemed to be on sleep, but when I tried to use it again it didn't do anything. When I try to turn it on the keyboard lights turn on for about 2 seconds, then it goes completely off and there is a faint cracking sound on the speaker bar.
I already tried taking the batteries off and using the AC/DC adapter only, it did not work. When I plug-in the AC/DC adapter the light around the power connector turns on.
Hope someone could help me. Thanks.

Try a hard reset, works sometimes.Disconnect all external devices first.
1-remove power cord and battery
2-press power button for 30 seconds
3-reinstall only power cord for first startup.
4-power on
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Integrated microphone stopped working suddenly on my HP i-7 DV6! I tried everything!

Hi guys! Thanks to anyone seeing this. My laptop's integrated microphone stopped working suddenly. I have daily skype meetings and it worked perfectly fine but today it suddenly didn't work. I didn't make any significant changes before that.
I tried uninstalling and installing the drivers from the website but when I uninstalled, the new drivers said that a device is missing. I cannot paste the error message exactly how is written for you because it is in greek. but the translation is that a device part is missing or something.
after that I've done a system restore went back 4 days and I have now my drivers back but the microphone still isn't working.
I figured out that if i plug my apple headphones i can hear audio but it doesnt detect my recording. (i dont know if it's supposed to anyway!
Thanks in advance to anyone that might have a solution!
Windows 8
HP Pavilion DV6-2150EV
Product Number: VY101EA#B1A
Serial No.

Thank you for this. You are amazing for trying to help me. I kept on not being able to find the solution for 2 days and no voice application worked until yesterday evening. I logged into an online shop and bought a headset costing £10. As long as I entered my details and pressed PAY, my girlfriend called me on skype and voila, she could hear me. I think there might be something wrong with the insides of my laptop! Might be a significant amount of dust and dirt.
Thank you very much again. If this happens again I will read this post again carefully and get back to you.
Best Regards
Michalis Odysseos

HT1430 my iphone 4 stopped working suddenly....i held the on button and the home button at the same time and it cam on...is this a fault as i cant have my phone switching off randomly?

my iphone 4 stopped working suddenly....it wouldnt charge or anything...i was told to push the on button and the home button at the same time and it came back on.
is this a fault with the iphone????
i cant have my phone switching off randomly...any help please...thankyou.

sometimes it happens, a hard reset will sometimes solve the issue.
If the issue starts happening more often, I would consider restoring the device to factory settings to install clean software. If the issue still persists after that, the device might need a hardware repair.
More info on backing up and restoring the software: http://support.apple.com/kb/HT4137
Good luck
Stijn

Sony vaio SVF14N16SGS TOUCH screen stop working suddenly help me to fix this

hi alli buy sony vaio SVF14N16SGS and calibrate a touch screen i working with laptop but approximately befor 20 minute laptop touch screen stop working suddenly!!!!!!!!!!!!!i am very disapointment from sony Corporation for this bull******e bug please help me to fix iti appreciate it

Hi Jimmy_N,
Thank you for considering Sony Community!
We're sorry to hear this issue. Please follow the troubleshooting steps here to isolate the issue:
Power cycle - Remove the battery and all peripherals -> press and hold the power button for 5 seconds OR, if the battery is not removable, remove all peripherals-> look for a battery off button on the bottom of the laptop -> push the button for 5 seconds
Reinstall driver - Go to Device manager -> Human Interface Devices -> right click and select Uninstall (DO NOT DELETE). Restart the computer. The driver will be reinstalled.
Reset BIOS - While the unit is restarting, tap the F2 key repeatedly. Once in BIOS go to Exit tab -> Get Default Values -> Save the changes and Exit.
Update drivers from Sony's support website or from where you purchased the laptop.
Your Vaio SVF14N16SGS is not a U.S. model. We do not have the drivers and software that support your computer. For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
Hope these help.
Thanks,
Vincent
If my post answers your question, please mark it as "Accept as Solution"

Yosemite - Bluetooth speaker stops working

I have an issue where my Bluetooth speaker stops working. It shows up on the devices list under Bluetooth but when I try to connect it does not do anything.
Rebooting fixes the problem. But then the next day when I try to use the speaker again it does not work.
This started happening with the upgrade to Yosemite.
Please advise, thanks,
OS X 10.10.1. MacBook Pro 15" Retina mid 2012

Scratch that. Things have improved in 10.10.2 - I am able to reconnect to the Bluetooth speaker more often, but it does sometimes fail and I have to reboot.

Upon sync or backup, I receive the message, "iTunes could not back up the iPhone "iPhone name" because and error occurred. I have deleted my backup file and tried another computer, with no success. Also, the bluetooth function stopped working.

Upon sync or backup, I receive the message, "iTunes could not back up the iPhone "iPhone name" because and error occurred. I have deleted my backup file and tried another computer, with no success. Also, the bluetooth function stopped working.

Hi, EJ13.
I see you are having issues with backing up you iPhone and have tried a couple troubleshooting steps. There are a couple more steps I could recommend in the article below.
iOS: Troubleshooting backup issues in iTunes
http://support.apple.com/kb/ts2529
Regards,
Jason H.

My iPod nano 6G stop working suddenly; After i reset it and even afetr put it in "stand by" mode by accessing deagnostic mode, it is still not working; Now i can access it sometimes (the main screen), but is not playing and is too slow. How can i fix it

My iPod nano 6G stop working suddenly; After i reset it and even afetr put it in "stand by" mode by accessing deagnostic mode, it is still not working; Now i can access it sometimes (the main screen), but is not playing and is too slow. How can i fix it

If you do not find a solution in the iPod nano (6th generation) - User Guide, suggest that you call AppleCare if still under warranty or take a trip to your local Apple Store or AASP.

CDrom Device stopped working

We purchased an Acer package about 3 weeks ago that came with an epson printer. The CD device was working when I loaded a photo gallery file and a game. When I was about to install the printer - the CD device just stopped working at all. An error under Device Manager shows 'A driver (service) for this device has been disabled. An alternate driver may be providing this functionality. (Code 32)'
At the same time, I was waiting for my internet provider to reinstall my internet because I found out that I can't go wireless. A week later my internet was finally up and working. Someone suggested to do a system restore from the day the CD device last worked. I did and it did work. I was finally able to load the epson printer and it was all working but by this time....my internet connection was lost. 'was wondering if it had to do with the timing that the date I picked....I had no internet connection yet. I went ahead and picked another date after my internet was installed and once again, the CD device stopped working and whatever installation I did with the printer was not located. So I don't know what to do. I know I'm still in warranty with Best Buy but is this something that someone can help me out from Best Buy or Geek Squad over the phone or do I have to bring the entire system to them. I have an online business and I can't really afford right now to lose more days since it took days already to have my internet back in order. Please help.

Perhaps an expert can come up here and tell you how to remove the terms 'upper filters" and "lower filters" from a certain part of the registry. I dont feel adventureous enough to explaining it withotu sounding like a dummy
*******DISCLAIMER********
I am not an employee of BBY in any shape or form. All information presented in my replies or postings is my own opinion. It is up to you , the end user to determine the ultimate validity of any information presented on these forums.

Bluetooth device stopped working suddenly.

Similar Messages

Maybe you are looking for