Boot Error: Errata bits for controller 0x8086

Seems to be a non critical error as system functions fine. But i noticed this only recently started appearing and not sure of exact cause. But I did some checking and did find this is the USB controler and each errata error corasponds to one of the built in devices which include
each of the internal 5 USB hubs linking to the devices
isight
bluetooth
keyboard/trackpad
IR Receiver
External USB hub (for hooking up everything else outside of comp)
what's causing these errors is unknown, but the hub calling the wake state change is the IR Receiver hub. Anyone else have any experience with this? not experiencing any bad behavior devices work fine system stable, just a recent change i noticed i didn't observe prior.
Sep 2 00:43:51 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
Sep 2 00:43:51 localhost kernel[0]: USBF: 10.721 Errata bits for controller 0x8086/0x27c8(rev 0x2) are 0xe800
Sep 2 00:43:51 localhost kernel[0]: USBF: 10.797 Errata bits for controller 0x8086/0x27cc(rev 0x2) are 0x5800
Sep 2 00:43:51 localhost kernel[0]: USBF: 10.810 Errata bits for controller 0x8086/0x27c9(rev 0x2) are 0xe800
Sep 2 00:43:51 localhost kernel[0]: USB caused wake event (EHCI)USBF: 10.812 Errata bits for controller 0x8086/0x27ca(rev 0x2) are 0xe800
Sep 2 00:43:51 localhost kernel[0]: USBF: 10.815 Errata bits for controller 0x8086/0x27cb(rev 0x2) are 0xe800

Thanks for the response. I found another thread for the same issue that stated I would need to RMA the device.

Similar Messages

Which of These Methods to Permanently Boot to 64-Bit

Hi. My iMac is the late i7 2009 model with 8GB. I'm guessing at my current 32-bit mode, once it needs more than 4GB, it won't be able to do so?
Is it adviseable to boot it to 64-bit nowadays?
For those who're booting in 64-bit for some time now, what're the advantages if any. Have you encountered problems and incompatibilities? 2011 iMacs and MBP seems to boot to 64-bit by default. My peripherals are just a wireless Intuos4, Apple wireless keyboard and wireless mouse and WD My Book Studio backup for Time Machine (My Book is good I think Time Capsule is still worth more paying for coz' of the ease of update integration). Not so industry standard third-party apps I use often, 2009 model of Corel Sketchpad Express and Autodesk Sketchbook Express.
If 64-bit mode is a recommended default, I found two methods. Which one should I use?
1) <key>Kernel Flags</key>
<string>arch=x86_64</string>
2) sudo systemsetup -setkernelbootarchitecture x86_64
Thank you in advance and Gbu.

Sadnakhleh wrote:
That is a 17" right? I am going to buy a 15" I think.
The biggest problem with the Asus in question is that it will be really hard to upgrade it and I still did not find a model with SSD.
I found a comparision review here: http://www.notebookcheck.net/Review-Asus-N550JV-CN201H-Notebook.98311. 0.html
The Asus scores better in the cinebench sector (slightly with OpenGL and much with CPU) and the Lenovo is better in the Pcmark7 and the 3dmark11. What are these tests? and which one is more important when it comes to video editing?
Thank you again for your time and efferts
P.S. I am studying the article about Hard disks, it is really interesting!!! thanks
Correct it is a 17-inch, and of course it weighs and costs slightly more than a 15.6-inch
It is a very simple task to upgrade the unit to an dual SSD system, and memory upgrade is very easy. You undo one screw on the bottom and (below) this is what you see. Two disk drive carriers with my SSD's installed and two 8 GB SODIMM add on RAM modules
Those benchmarks have very little to do with editing with Premiere, there is only one real comperhensive Premiere benchmark it is our PPBM.

Cisco MCS 7835i3 CM 7.1.5, unable to boot giving ECC bit DIMM Error, Urgent help required

Hi,
One of our client is using CUCM 7.1.5, on MCS 7835i3. CM is now unable to boot. giving ECC bit DIMM error. We have serviced MCS, then started, it started working but only one hard light is blinking. Is there any problem with hard or something else. As well show hardware logs are attached.
Please find attached snapshots.
Regards,
Humza Khan

Hi ,
Try to reseat the RAID controller i it helps else follow what Terry has said.
http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=migr-5074114
http://public.dhe.ibm.com/systems/support/system_x_pdf/ibm_doc_sraidmr_10i-10.03_user-guide.pdf
regds,
aman

Where can I download Boot Camp 4.0 for Windows7 64 bit?

Hi,
I'm wondering where can i get a download of Boot Camp 4.0 for Windows7 64 bit?
Now, I'm using the latest Mac Air (Late2011) w/ OS X Lion. Or I can just using Boot Camp 3.3 for Windows without any conflicts with Boot Camp 4 on Mac OS X Lion?
Thxq for your advice.

Frequently asked questions about Lion and Boot Camp 4.0
Stefan

ITunes Error 7 (Windows error 127) after installing iTunes 64-bit for Windows

After installing iTunes 64-bit for Windows (latest build), I get an error pop-up saying:
iTunes was not installed correctly. Please reinstall iTunes
Error 7 (Windows error 127)
I've gone thru the uninstall, reboot and reinstall process three or four times now. Still nothing.
Furthermore, after clicking okay to the error, it continues to pop up on it's own every 45 seconds or so.
There was one other error I came across after trying to launch iTunes after installation.
See both error messages here:
http://screencast.com/t/DSg4PpKF5BeX

Brilliant. Thanks a lot. I've wasted a couple of hours on this nasty bug, & trying all the other suggestions across various threads again and again.
I now find I had the same registry entry hanging on, despite uninstalling & wiping everything again and again. Having now deleted this key, (I don't even have an iPod), & iTunes 11.1.14 now opens at long last.
But WHY is this bug not fixed? Enough people are suffering with this across the forum. WHERE is Apple support on this?
It should have been added to their page at
http://support.apple.com/kb/HT1923
by now, why hasn't it???
It's not good enough!
Re:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\SharedDlls]
"C:\\Program Files\\iPod\\bin\\iPodService.exe"=dword:80000000
AHA! This entry for iPodService.exe still exhisted. So I had no folders on the PC, no installs on the PC and no services running.... BUT this was still in the Registry.
Step 5 - Delete only the Registry entry above. NO REBOOT
Step 6 - Reinstall iTunes64.exe

How to limit servermgr_filebrowser to boot volume, to prevent 'Error getting quotas for volume'

Having a system with 1 boot drive and 15 backup drives, we do want to limit the server manager 'servermgrd' its 'servermgr_filebrowser.bundle' to retrieve/check the disk quota only on the boot volume ('/').
Because:
the backup drives are FAT formatted, which will fail every time with this error message: 'servermgrd: servermgr_filebrowser:Error:servermgr_filebrowser: Error getting quotas for volume /Volumes/I of type exfat'
the quota check is repeated every 2 hours (120 minutes), causing the log the be filled with these message and the drives to spin up 12 times a day (consuming more power than necessary and causing extra drive wear)
How can the server hard disk drive quotum check be limited to the boot volume only (not scanning for any other volume)?
And when that isn't possible, what is the correct way to completely disable servermgr_filebrowser?

Thank you Mark you are vary helpfull
Did you mean that (lower) by "bundle strategy"?
<cachestore-scheme>
<class-scheme>
<class-name>com.griddynamics.ticketon.app.dao.coherence.TicketCacheStore</class-name>
</class-scheme>
<operation-bundling>
<bundle-config>
<operation-name>store</operation-name>
<preferred-size>5000</preferred-size>
<auto-adjust>true</auto-adjust>
</bundle-config>
</operation-bundling>
</cachestore-scheme>
And if yes is it looks sense?
I mean by this, "send records to TicketCacheStore by 5000 per call " am i right?
I dropped delay to 10s and set factor to 0.5
Not coherece send me 5-20k records and cachestore handle whis successfuly.
But! By diferent means it may work longer sometimes, some lock in database for instance.
I want to find durable solution for the case, not only lower a chance i meet one.
Issuing heartbeat from cachestore looks best for me now.
I find that default guardian timeout is 65s and it is not looks as good idea to make it higher.

Do not upgrade to an IvyBridge processor if you need to boot into 32-bit mode with Lion

I recently upgraded to a MBP running the Ivybridge processor and tried to boot into 32-bit mode. Although it did boot after a short period (3-5 mins) it totally crashed a locked up. This was precursored by a graphics error and then the mouse cursor could be moved but nothing else could be done and it was only solved by a hard shut down (holding down the power button). Previously I had been running a MBP with the Sandybridge architecture and this booted fine into 32-bit mode and worked without a problem.
I spent a lot of time on the phone with Apple care who said they'd not had any reports of this issue and we went right though my system until they said there was nothing else they could do and I should try a re-install of Lion. I did this onto another hard-drive, booted into it and managed to get the machine to crash again... leading me to understand that it's nothing to do with my setup.
Thinking it might be an issue with my firmware on the mac today I visited an Apple store and tried booting 5 MacBook Pro's and a MacBook Air - all running IvyBridge - into 32-bit mode and managed to cause the same crash on all of them. If the machine is just booted an left with finder it didn't seem to want to crash but when I opened programs, mainly mac mail, it didn't take too much longer for the crash to occur.
If there are any Apple engineer reading this could you try and reproduce the issue and look at fixing this please as a lot of people still use 32-bit and if I'd known that the IvyBridge processors weren't going to work in 32-bit mode I would have stayed with the Sandybridge MBPs.
Many Thanks,
Adam Peters,

That is a pain then. Pretty much all of the OS included applications (finder, Mail, iTunes, Safari,...) are all fully 64-bit programs now (since Lion) so I can see where launching them when booted into 32-bit mode could cause stability issues.
If you boot into 32-bit mode and just run the Tascam software without launching anything else, will it work?
Was it alright in 10.6? And if so, how about keeping 10.6 in a virtual machine or on a separate disc or partition?

[Solved]Syslinux "booting... boot error" when booting Windows 7

Hello, I've set up my computer to dual boot windows and arch. Windows is on a separate hard drive and I was able to configure syslinux with a boot menu allowing me to select Windows at startup. For a long time this has worked without any problems whatsoever, but this morning I tried selecting windows and I got what is probably the most vague error message I have ever seen.
"Booting...
Boot Error"
According to this post this problem comes in when the ldsyslinux.sys file cannot be found. Unfortunately I was not able to use his suggested fix
syslinux -U /dev/sdb1
I wasn't aware that there was a -U flag for syslinux and after checking it seems that there isn't one.
Last edited by samstr (2014-11-26 04:48:55)

Sorry, I actually just fixed it on my own, it turns out my BIOS settings were a bit... weird. For some reason I didn't have my windows drive listed and it tried to boot a USB drive I had plugged into my computer. I just had to fix the drive order and it worked fine. Sorry about starting a fairly useless discussion.

Boot error message on new install of Paravirtualized arch

Hello,
I just finished installing a PV arch guest on xen.
I get the following error at boot:
[1.185226] i8042: No controller found
[1.1247134] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Google told me this is the driver for the hardware clock so I tried the following:
[root@coronelaurelianobuendia ~]# hwclock --systohc --utc
hwclock: Cannot access the Hardware Clock via any known method.
hwclock: Use the --debug option to see the details of our search for an access method.
[root@coronelaurelianobuendia ~]# hwclock --debug
hwclock from util-linux 2.24
hwclock: cannot open /dev/rtc: No such file or directory
No usable clock interface found.
hwclock: Cannot access the Hardware Clock via any known method.
Does anyone have any ideas? Is this a problem with my grub.cfg? A problem with PV arch? or a problem with my kernel?
Thanks for your help and advice

Hi , I see you have been troubleshooting an issue with your new LaserJet Pro MFP M127, and I may have found some items you can check.
This issue is usually caused by some sort of packing materials that may be hiding on you. I would double check Setting Up the Printer Hardware for HP LaserJet Pro MFP M127fw to make sure it's not a piece of cardboard inside the printer. The next thing that may cause this would be if you forgot to remove the orange tabs on the toner cartridge. If you take a look at Replacing the Toner Cartridge, it shows what needs to be removed from the toner before installing it inside the printer. There is a whole setup video about Unboxing and Setup of the LaserJet Pro MFP M127 you can watch as well. If the issue persists, you might still have options covered under the HP LaserJet Print Cartridges and Imaging Drums Limited Warranty Statement - I would still try to Contact HP Support to see if there is anything they can do. Fill in the model number and the form to receive a case number for expedited assistance. Please let me know if these steps resolved your issue, or if there is anything else I can do to help. I look forward to hearing from you! Thanks,

GE60 0NC booting error

Hey guys my GE60 0NC seems te have some kind of issues.
When I boot it and logg in the booting seems to stop at the WiFi connecting.
At that moment I can start a few minor programs but a lot of booting hasnt been finished yet.
To fix this I tried to:
-Systemrepair it to 1 day ago
This seemed to help, I could use it again although it ran a lot slower than normal.
In addition some programs seem to have some error, for instance League of Legends won't boot.
However when I shut it down and rebooted it again I was back to the same booting error.
What could be the problem here?
Thank you very much for your time.
Olav

I've been having the same problem for over a week (MSI GE60 - i5-3210M, 6GB RAM and GT650M; bought a bit over a year ago).
It started with a normal boot, but when I logged into my account I couldn't start any programs for 5-10 minutes. My S-Bar also stopped responding and crashed.
At first I suspected malware/virus, and actually found some shady files that I deleted with Malwarebytes Anti Malware.
The problem was still there though, so I did a system restore (I couldn't go back more than a few days) and that seemed to fix the problem - but after a reboot it was back.
I could find some errors, like the one you linked, in the Event Viewer - but also alot of Information-events from NvStreamSvc (several every sec) which is a part of Nvidia.
So today I uninstalled GeForce-experience (couldn't launch it apparently, got some error) and then installed an older display driver 310.90.
I also reinstalled my S-Bar and now it seems like I run pretty decent. The WiFi-logo has gone back to normal and I can start up programs early after a boot.
You could also try and uninstall some recent Windows Updates - I'm not sure if they're involved, but you could always give it a try.
Hopefully this helps you, or someone else, in some way.

Boot Error with grub installed...no debug instructions

* Quick Intro / About *
Hello everybody... im new to linux in general and arch caught my eye since i have an interest in learning programming... i figured arch's documentation was better than that supplied for ubuntu since it's more in depth and has the core utilities needed to get a base system running with in-depth explanations (which i like). trust me when i say, i have read almost all of the arch documentation more than
a few dozen times and have completed this successfully before...
* My Problem *
I installed my copy of Arch with the Core Utilities package and followed the wiki guides to the tee. i've done several test installations with VMware and Virtualbox OSE and decided to do it for real on my Toshiba Laptop Satellite l305d-s5895... all my hardware is currently supported by the majority of the Linux Distro's (i did my homework). I am attempting to do a dual boot with Arch and Windows
the "/etc/rc.conf" file
Localization -> default
Hardware -> default
Network ->
HOSTNAME="myhostname"
the "/etc/hosts" file is automatically adjusted during install
eth0="dhcp"
INTERFACES=(eth0)
gateway="dhcp"
ROUTES=(!gateway)
Deamons -> default
filesystem setup
win7 -> hd0,0 sda1 primary
arch -> hd0,1 sda2 primary
swap -> hd0,1 sda5 logical
cdrom -> sbd (device is auto-mounted)
/dev/sda (MBR / Single HDD Device)
After Grub Configuration ...these are my options to select for grub mount point
/dev/sda
/dev/sbd
/dev/sda
/dev/sda1
/dev/sda2
/dev/sda5
/dev/sbd
I always select /dev/sda at the very top of the list...
the "/boot/grub/menu.lst" file
Gen Config ->
timeout 5
default 0
color light-blue/black light-cyan/blue
Boot sections ->
# (0) Arch Linux
title KDM
root (hd0,1)
kernel /boot/vmlinuz26 root=/dev/sda2 ro vga=ask
initrd /boot/kernel26.img
# (1) Fallback (default settings)
# (2) Windows
title Windows 7
rootnoverify (hd0,0)
#makeactive #win7 does not require this
chainloader +1
* the Error I recieve *
At boot and during reboot, unless i have a boot medium, this is what i am prompted with...
Intel UNDI, PXE-2.1 (build 082)
Copyright (C) '97 - '00 Intel Corp.
For Realtek RTL8101E/8102E PCI-E Ethernet Controller v1.05 (071227)
PXE-E61: Media test failure, check cable
PXE-M0F: Exiting PXE ROM.
No bootable device -- insert boot disk and press any key
any help would be amazing! i have no idea why at boot the computer searches for a network connection
instead of the GRUB! >.<
i am able to boot however with the Arch Live Disc and access my filesystem for both Arch and Windows 7
and resume normal use!

well, just as an update... i believe it is a software issue... i wiped my whole HDD with gparted and set the partitions with Arch Live Core Install medium and GRUB worked perfectly... i created an NTFS partition as well for Win 7... hopefully the Win Installer wont overwrite GRUB and use its own bootloader. i was re-reading an area of the wiki and found...
- GRUB must be installed on the MBR (first sector of the hard disk), or the first partition of the first storage device to be recognized by most BIOS's.
source: https://wiki.archlinux.org/index.php/Gr … stallation
hopefully i can just reinstall GRUB if needed with the Live Disc and i can boot win7 and arch like that...
if an suggestions, or comments, please...would be nice.
Last edited by xovertheyearsx (2011-03-11 05:23:05)

EFI update tu support booting into 64 bit OS

Hello,
my mac (see signature) does not support booting into 64 bit in Snow Leopard. I also have troubles to install any 64 bit Windows.
The tool: http://www.ahatfullofsky.comuv.com/English/Programs/SMS/SMS.html says:
64 bit processor, 32 bit EFI, 32 bit kernel boot mode, 32 bit kernel
and its technically possible to boot into 64 bit kernel mode but it is not recommended by Apple.
It is possible to get a 64 bit EFI update to solve it?
thanks

Hi,
try this
http://www.ahatfullofsky.comuv.com/English/Programs/SMS/SMS.html
It seems that your model is in the list of supported models that can boot the 64 bit kernel.
I had the same issue with my macbook pro with identifier MacBookPro4,1 and booting with 64 bit kernel solved it.
I hope you can solve your problem!
Sorry for my bad English :-D

Windows 7 Pro (x64) - Boot Camp 2.0 or 2.1? Boot Camp (64-bit)?

I recently got Windows 7 Professional (x64) - note it's NOT the beta - installed on my late '08 MBP (this was no cake walk...), and I have a question regarding Boot Camp versions. I'm pretty sure I have only Boot Camp 2.0 installed. When I try to run/install the 64 bit Boot Camp 2.1 version/upgrade for 64-bit Vista (BCUpdateVista64.exe), it simply won't start.
I read someplace that this is supposed to happen, as 2.0 is better for my current situation (Windows 7). Other posts seem to suggest I should download and install 2.1 in order to get everything working properly. Which is it?
Under Control Panel in W7, I have a blank icon that says "Boot Camp (32-bit)" and says application not found when clicked. Is there a 64-bit Boot Camp I can install?
I ask all this mainly because I suspect it may bring about some answers regarding trackpad support in Windows 7 (x64). Thanks in advance!

Snow Leopard changed things

Short of dismantling and recreating a page how do i find out whats causing [Error: Invalid URL for Web Content Overlay]

Hi,
i received an indesign file to include in a folio that had links to the creators desktop where they had the assets for the web content overlay. When i try to update the folio i get the error message:
"Content generation error.
[Error: Invalid URL for Web Content Overlay]"
Which is fair enough.
The problem is, i have gone through and changed all URLs that I can see, but there is one somewhere, that I just can't find.
Is there a way to get a list of all web content overlays in a particular file? otherwise i will need to recreate the whole page again, and it has some pretty complex interactions which i rather wouldn't do.
I also cannot ask the original doc creator to just change the links as i'm sure he'll have the same issues as me, at not being able to track down the erroneous link.
The problem I have with DPS is that its not very transparent. you'll have to click on everything, and into every group to see what actions are on it, which can be extremely time consuming and frustrating when complex interactions are included.
thanks in advance for any assistance

I’ve found watching the process helpful to narrow down the page.
Working off a duplicate of the file, delete one layer at a time until you figure out what layer the problem is on.
From there it’s a bit easier to narrow down.

Error when creating custom controller

I have a non-visual WebDynpro DC that contains a single data model. The model has been added to the public part of the DC.
I have another visual WebDynpro DC that makes use of the data model in the first DC. If I explicitly reference the model in the first DC, everything works just fine. I can input data, invoke the model, and see the response displayed on the page.
However, I'm trying to create a custom controller that hides the data model. When in the data modeller for the visual WD DC, I right click on the 'Custom Controllers' pane, and select 'Apply Template'. I create a Service Controller, and select the model that's been imported (actually, that's been referenced as a used component) from the first DC. I then select the data elements from the context that I want bound into this custom controller. Click next, give a more descriptive method name, and then click Finish. I get an internal error as follows:
Source controller implementation file is not accessible (D:/src/.dtc/LocalDevelopment/DCs/example.com/test-wd-view/_comp/gen_wdp/packages/com/example/wd/AdderModelCust.java)
Exception: java.lang.NullPointerException
Am I doing this correctly, or am I missing a step or two?

Hi Ken,
you didn't miss some steps, this seems to be a bug in the tools. Please open a OSS message with the following information:
- which Studio version you use (NW04/04s? SP?)
- description of how to reproduce the effect
- Studio's error log attached (.log file in <YourWorkspaceFolder>/.metadata)
In the meanwhile to circumvent the error you should try to
- create a new custom controller manually in WD explorer and launch Service Controller template from this controller (context menu in WD explorer)
- if this fails as well, manually create the context definitions and method implementation that the template would produce.
Regards
Christian

Boot Error: Errata bits for controller 0x8086

Similar Messages

Maybe you are looking for