Bridge-group input-address-list

I have this query regarding the above command.
This is the access-list created
access-list 700 permit c89c.dca0.5539   0000.0000.0000
access-list 700 deny   0000.0000.0000   ffff.ffff.ffff
And applied to the interface
interface FastEthernet0/0.2
encapsulation dot1Q 2
ip dhcp relay information trusted
ip address 192.168.0.1 255.255.255.0
ip accounting output-packets
ip nat inside
ip virtual-reassembly in
bridge-group 2
bridge-group 2 input-address-list 700
but then an unknown device is also getting an IP. why is this so?
RTR1#sh run | i 700
access-list 700 permit 000f.fed9.dee8   0000.0000.0000
access-list 700 permit c89c.dca0.5539   0000.0000.0000
access-list 700 deny   0000.0000.0000   ffff.ffff.ffff

ah. unfortunately this command not available.
c2800nm-adventerprisek9-mz.151-4.M5

Similar Messages

Global Address List (GAL) does not show up under group Contacts

I am an exchange administrator for a large organization. One of our user has an issue where he cannot see the GAL on his phone. Goes to Contacts, tap Groups, no option for GAL available. I have set up the Exchange account on the phone and he can get emails. Mail, Contacts, Calendars are all on. I have deleted the exchange account and created a new one but still no GAL. Please help. Thank you in advance!

On my phone I go to the Groups screen and at the bottom of the list it says "(account name) Global Address List".

OWA 2010 error when access Groups address list

Exchange 2010 SP2
We use multiple ABPs for different OUs (which is different subordinates).
I found strange error in ONE subordinate.
Users in there? when they try to access an entry in Group list receive an error:
"Access is denied."
" ! The Active Directory resource couldn't be accessed. This may be because the Active Directory object doesn't exist or the object has become corrupted, or because you don't have the correct permissions. "
Any ideas?
UPD1.:
Found trouble - GAL policy didn't work correctly, so OUs GAL wasn,t wrote into AD attribute
showInAddressBook
Cure: manually add record about GAL into this attribute.
Same trouble with distr.groups not resolved YET

Hi,
From your description, I recommend you check the permission of the GAL via ADSIEdit.
Navigate to CN=Configuration, CN=Services, CN=Microsoft Exchange, CN=YOUR-ORG, CN=Address List Container CN=All Global Address Lists
On the right hand side you will now see your Global Address List. Right Click it and select properties then the security tab. Please check if there is deny to read rights for users, if yes, please uncheck it and test again.
Hope it helps.
Best regards,
Amy Wang
TechNet Community Support

How do I email a group from a list of email addresses in a pdf?

how do I email a group from a list of email addresses in a pdf?

Work Around:
On your mac:
1. Open a new email
2. Insert name of an existing group into one of the "To" fields as usual.
3. Highlight all the resulting names in the "To" entry
     [Highlight first name, and while holding shift, highlight last name and all will highlight[]
4. Copy (Command C) the highlighted emails
5. Paste (Command V) nto a pages document
6. Remove the name and anything else preceeding the first < and also the first < of only the first entry whixh will look like this:
     [email protected]>,
7. Remove the > of the last email which will look like this:
     , Jane Doe <[email protected]
8. Copy the entire altered list from the pages document
9, Go to Contact Book and click + to add a new entry
10.. Name the entry (XXX Group for iPad) or whatever you wish to call it
11. Paste all the copied altered list into any one of the email entry spaces
12. Click on "Done"
13. Create new email On iPad and click on + in any one of the "To" lines and search for "XXX Group for iPad" You cannot just key in XXX Group for iPad!!!!!!!, you must use + contact search.
14. Enter the selected iPad contact group into the "To" line.
15. All the entries will now appear in the "To" line and you are good to go.
Adding or deleting email addresses from the iPad group:
Easiest: Alter the original mac group in the usual way and repeat steps 1-14 above. It seems impossible to edit within the emai line of the iPad contact entry.
Rediculously simple once figured out.
Happy emailling, but please send Bcc so that you don't spread your groups' email addresses all over the internet for spam, viruses, and other unwanted emails. Be considerate and ask your recipients to notifiy you if they wish to be deleted from the lists you compose.

Limit when input mail address list to "TO" field in Delivery function of BI

Hi all,
I am deploying BI Publisher for my partner. I have troubled when put mail address list to "TO" field in Delivery function in BI Publisher. May be serverlet had limted it. I know that I can write a address mail list directly to DELIVERY_PARAMETERS in XMLP_SCHED_JOB which has BLOB type.
But I am thinking that, If i buy license of BI Publisher, how i can do it earsier?
Thanks all.
Please send your solution to my email: [email protected]
Edited by: user6064593 on Jul 23, 2009 1:03 AM

Hi vlp,
You can achive it with BAdI:CRM_ORDER_FIELDCHECK. Actually I've implemented the similar case with this BAdI. This BAdI is called many times because it always works when any field is changed. So you should restrict the timing your logic works.
Regards,
Masayuki

Cisco 877w -Configuration of subinterfaces and main interface within the same bridge group is not permitted

Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!

Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter

Cannot send email to Smart Group from Address Book

I created several Smart Groups in Address Book but I can't use any of them to send email. When I right-click the group name and choose Send Email, it opens my default email program (Thunderbird) and puts only the name of the Smart Group into the To: field, not the actual addresses.
If I try to actually send the message, I get the error that (name of group) "is not a valid e-mail address because it is not of the form user@host. You must correct it before sending the email."
What am I doing wrong? How can I get it to paste the actual addresses and not just the name of the group? I looked at the Edit Distribution List window and all the addresses are there.
I'm using OS X 10.5.7, Address Book 4.1.2 and Thunderbird 2.0.0.22.
Thanks in advance.

What is the exact message you get when sending fails -- does it say there are one or more invalid addresses, or what?
Having a name in the list without email address or possibly one separated by comma between last and first might result similarly in an invalid address, and Mail will likely refuse to send to any. But if the message is from the SMTP, that might depend on the provider's policies for that.
Ernie

Upgrade Default Address Lists from LDAP

Hello,
I migrated from MS Exchange 2003 to 2010 some time back. Currently trying to upgrade the address lists as per the guide here:
http://technet.microsoft.com/en-us/library/dd351283.aspx
When I run
Set-GlobalAddressList "Default Global Address List" -RecipientFilter {(Alias -ne $null -and (ObjectClass -eq 'user' -or ObjectClass -eq 'contact' -or ObjectClass -eq 'msExchSystemMailbox' -or ObjectClass -eq 'msExchDynamicDistributionList' -or ObjectClass -eq 'group' -or ObjectClass -eq 'publicFolder'))}I get the following error:what should I do? Thanks.

Hi Birenc,
the default Global Address List can be modified during the conversion from Exchange 2003. You won't be able to do it after that hence the error message.
1- Run Get-GlobalAdressList | fl and check the IsDefaultGlobalAddressList value. I believe in your case this would be False.
2- To change this you would need to change the msExchRecipientFilterFlags attribute. you can do this via ADSIEDIT. Open ADSIEDIT connect to the Configuration container. Find the Default Global Address List and change the above attribute value from 3 to
0 and apply the changes. Then change it back to 3 and apply changes.
3- Run GlobalAdressList | fl again and the IsDefaultGlobalAddressList value should now be true.
This should fix your issue.
ecsword

Can't send email to an icloud group in address book

Hi
I have set up some groups in icloud. I called one of these groups "Test", with only myself as a group member. In address book, when I right click to send email to "Test", it fires up a new email with the word Test in the email "to" field. If I try to send the email I get the error message "Test" doesn't seem to be a valid email address. It doesn't seem to be filling in the group email addresses in the "to" field.
Am I doing something wrong?, or is this a known or unknown bug?
I have other groups set up but I obviously don't want to send test emails out hence the test group "Test"
Also when I edit the distribution list and right click the group name, "send email to "Test" is greyed out.
Many thanks in advance

Bump

How can I add multiple addresses to a group within address book?

I realize you can add in addresses by going to 'Message' then 'add Sender to Address Book,' but what I'm interested in doing is within Apple Mail, adding multiple addresses into a specific group within address book. I've tried to do this using mail scripts but keep getting an error.
Is it possible to do this?
Thanks.
David

So far, FWIW all I've got is individual AddToAddressBook, then in AB itself, drag and drop one by one from the main list into the desired group.

How can I share address lists between two iCloud users

My daughter and I have two different icloud accounts. We are able to share certain calendars, but I would like also to share address lists/groups. Is there a way to do this? I think you could "subscribe" to another Mobile Me user, but how is this done in ICloud?

I do understand that if we have the same Icloud account and Apple ID then they will sync automatically. We don't. I have just separated our accounts (on purpose). Via icloud we can share calendars, but I want to share address lists too. Can address lists be shared (or subscribed to) by two different icloud users with two different Apple IDs?
Anybody know?

Can I share addresses lists between 2 different iCloud users?

Does anyone know if I can share address lists/books between two different iCloud users? I know you can do this with a calendar, but I would like to do it with addresses too.

Yes.
Go to Settings -> Mail, Contacts, Calendars
Add a new account if type iCloud, and username/pasword for the secondary account you want to access their contacts. Turn off all but Contacts, and you wll now be seeing their contacts on your iPhone.
Now in your contacts app, under Groups, there is a new section of contact from the new iCloud account you just setup. If you have the contacts app open (even minimized) you may have to force it closed and re-open to sync in the new contacts.

Cisco 1702i WAP: how to get an interface in a non-native bridge group/ VLAN to be recognized by the internal DHCP server

Does anyone know how the internal DHCP server in these access points connects to virtual interfaces and bridges in the unit?
Is there some sort of default connection that connects the DHCP server to the native bridge group or VLAN?
In a test case, with an SSID in the native VLAN and bridge group, the 1702i serves an IP address to a wireless client no problem. But with a second SSID in a non native VLAN and bridge group, no IP gets served. My only guess is that since the bvi1 defaults to the native bridge group and VLAN, sub-interfaces also in this group are assumed to be in the same subnet as bvi1, or in this case:
interface bvi1
ip address 192.168.1.205 255.255.255.0
no ip route-cache
exit
It would be the ..1. subnet.
Since the dhcp pool is set as:
ip dhcp pool GeneralWiFi
network 192.168.1.0 255.255.255.0
lease 1
default-router 192.168.1.1
dns-server 8.8.8.8
exit
There may be an assumption that anything bvi1 can talk to is in the ..1. subnet, so the above pool gets activated on a request coming through bvi1.
Is the DHCP server just hanging out waiting for a request from an "area" that is assumed to be on the same subnet as the given pool?
Do I need to somehow show the device what subnet the 2nd SSID/ subinterfaces are in so the internal DHCP server can decide it needs to go to work, or is there some sort of bridging between the DHCP server and the interfaces that needs to be done? I am trying to use the same DHCP pool for the second subnet at this point, since I assume I will need another router to service an additional subnet and DHCP pool.

Keep in mind that DHCP is a broadcast packet to start. So the AP can only listen in the subnet that it has an IP address for.
Now, for any other subnet you can use the AP for DHCP but you have to have an IP helper address on your L3 pointing back to the AP.
That being said, I wouldn't use the DHCP server on the AP as it is limited. You'd be better off using a Microsoft server or some other device that is designed for DHCP.
HTH,
Steve

How can I see the indivduals in an existing group email address - that I created

I have a group email address on Thunderbird that I created some time ago but have forgotten how to open it up to see who is on it - I need to alter it.
Thanks

click on 'Address Book'
A sub group known as a Mailing List will be a sub group to an address book.
If Mailing Lists are not showing, click on the small arrow to the left of the address book containing the Mailing List.
See image below - example shows I have a 'Test' Masiling list as a sub group to 'Personal Address Book'
Then select the Mailing list to see who is in that Mailing List.
Removing contacts from a Mailing list does not remove them from the associated address book.
Removing them from the associated address book will remove them from both address book and Mailing list.
You can drag and drop new contacts into a Mailing List, but they do need to have a valid email address.

Auto update of contact groups in Address Book when created on iphone?

So, I'm OK with how to work with two phones on the one itunes account, with regard to contacts and calendars, but can I get Address Book to automatically add any new contacts created on each phone to the correct contact group?

In iTunes, on the Info tab with the iPhone connected, there's a pop-up menu to choose the Address Book Group to which new contacts created on that phone are added. Check the box and select the proper group from the list.

Bridge-group input-address-list

Similar Messages

Maybe you are looking for