BUG REPORT FIRMWARE 5.1.7  PLEASE FORWARD TO SUPERVISOR....

BUG REPORT FIRMWARE 5.1.7  PLEASE FORWARD TO SUPERVISOR.
The spa-3102 has the following two bugs.
When the unit sends a hook-flash to the fxo port it:
a)      does not send the hook flash to the fxo port  for PSTN Hook Flash Len:  Instead it uses a very short pulse of about 100ms or 1/10 of a second.  It should honor the PSTN Hook Flash Len configurable parameter of .2 – 1.5 seconds.
b)      Does not change the line voltage from –7 (off-hook) to –48(on-hook) during a flash-hook to the fxo port.  Instead it varies the voltage only by about 2.5 volts.
This was reported as early as June 07 to linksys support.  It is reported they agreed and would fix in the next firmware release.  There is info that firmware 5.2 being released and is this fix in 5.2 and how can I get it.

Although the problem is still not solved, at least I now know WHY the problem is happening... and Apple's Firmware Update is NOT to blame!
Through a series of coincidences, I was actually lucky enough to get in touch with the engineers in Apple's Airport firmware division, and they were helping me to nail down this problem.
Turns out that Apple takes great PRIDE in the fact that they are one of the VERY FEW manufacturers who make routers that behave properly in this regards: they SPECIFICALLY test for their Airport Extreme routers to allow you to connect to servers behind the NAT by way of the public WAN IP address of the NAT box. This is the way that apparently the NAT/DHCP specification is SUPPOSED TO WORK! You're SUPPOSED to be able to connect this way, if you so desire.
So what was causing the problem on my network, then?
Something I hadn't thought about... the Vonage Linksys RTP300 router that we're using for our Vonage VoIP service. Turns out that this router does NOT support clients behind the NAT connecting to servers behind the NAT by way of the public WAN IP address.
Linksys is to blame, not Apple!
And apparently, this feature may have actually been working in an earlier
firmware update, but apparently, Vonage AUTOMATICALLY pushes firmware
updates to RTP300's, apparently without user notification:
<http://www.vonage.com/help.php?article=1066&category=90&nav=5>
And a forum thread on vonage-forums.com seems to indicate that the 1.00.60 firmware in the RTP300 started getting pushed to customer units on or before 1/26/06, making it less than a month after Apple shipped the 5.7 firmware update for AirPort Extreme Base Stations:
<http://www.vonage-forum.com/ftopic10915.html>. So if the problem cropped up then, it's possible that I accidentally attributed it to Apple when really the RTP300 got a firmware update around then too which may have broken this feature (assuming it was working before then).
Power Mac G4 QuickSilver Dual 800 MHz   Mac OS X (10.4.4)  

Similar Messages

  • Is there ANY way to report firmware bugs to nokia ...

    Nokia released firmware 51.018 for E52 6 months ago.This broke N-Gage and games which were paid for can not be activted.The problem is not corrected in later updates.
    Firmware v52,v53,v54.Nokia Care centers tell me its Network problem.I have tested 5 E52s and it is a firmware problem.Mailing to ASK nokia does not reult in bug getting known to programmers either.They lecture me about correct settings.
    Some body please tell me if  there ANY way to report firmware bugs to nokia programmers
    Solved!
    Go to Solution.

    do you think there will be a new firmware update for e52?
    E52 - Product code 0585050
    UK.
    V54.003

  • Could someone please explain to me how to file a bug report?

    Hi,
    I had a problem recently with a bug in uevnts. I found a workaround for it, However when I went to open a bug that had similar symptoms the user got mad and closed the bug. Could someone please explain to me what I need to do to correctly file a bug report, and please don't say read the wiki. As in order to get log files, I need to know where they are, etc...
    Thanks,
    MarcoRosso.

    What questions remain after consulting the wiki? Maybe you can post the bug report in question, so it will be easier for others to point out how you could have responded more constructively. First general place to look for log files is /var/log/*.
    Last edited by hokasch (2010-04-13 00:55:35)

  • Inclusion of a bug report section in Forum

    I had contacted Sony on this matter, that a Bug report Forum should be created or this functionality should be added in the existing Forum.
    I sent them tem this:
    would like to suggest you that you should start an interactive forum like website just for software updates wherein all bugs in software can be reported directly to Sony and if on the spot solution is there then should be provided and the reported bugs should be quickly removed through quick and frequent OTA updates for all Xperia Phones. This is a humble request and a must do for Sony. Regards.
    And got this:
    Greetings from Sony Xperia support.
    We would like to take this opportunity to express our appreciation for your interest in Sony products and services.
    We have taken this as a valuable feedback and we have forwarded the same to the consumer feedback division for their due consideration.
    Any update in this regard will be posted on our web site.
    If you need any assistance or clarifications, please feel free to contact Sony Xperia Support at the Toll Free number 1800-3000-2800 (Working Timings-9:00am to 9:00pm: Mon-Sun) alternately, you can email us at [email protected]
    For the latest news, information and product support please visit www.sonymobile.com/in
    Always looking to serve you better.
    Kind Regards,
    So this has to be done, where users can report bugs for their Xperia devices and Sony making use of them should quickly swnd a small firmware upgrade as soon as possible , making the users wait for 6 months or so for a bug fix update.

    Thank you again for sending us your feedback.
    At the moment we don't have any specific board for this on our forum but you can always submit any reports or issues you may experience via your local support or here on the forum (in the concerned models board).
     - Community Manager Sony Xperia Support Forum
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Bug report: vpn (ipsec) interface number in snmp always change

    Hi,
    this is a bug report for RV082 hardware version 3 and 4, firmware version 1.x, 2.x and 4.x (all latest versions). I hope someone from cisco/belkin reads it.
    Summary:
    The snmp interface number of a VPN Tunnel change when the VPN tunnel disconnect and then re-connects.
    What should happend:
    The VPN Tunnel number 1, should always have the same snmp interface number. In RV082 v4, this number should always be 10. For example, the LAN, WAN1 and WAN2 always have the same snmp interface number.
    What is the problem:
    The VPN Tunnel number 1 change the snmp interface number, from 10, to 11, to 12, etc.
    How to reproduce:
    create a VPN Tunnel using 2 RV082 or 1 RV082 and 1 RV042. Once the VPN Tunnel is connected write down the snmp interface number. A few days later, disconnect the cable of block internet access. Then restore the internet conection and write down the snmp interface number, you should note that the snmp interface number have changed.
    Tools used:
    PRTG Network Monitor
    Please take a look at the attached image, note all the "ppp" interfaces, theres only 1 VPN Tunnel (gateway-to-gateway) defined.

    Hi Tom,
    many thanks for your reply.
    I see that I have to call Tech-support, in order to report a very technical situation, explaining them this is a bug report and I want them to make a better product.
    Since I won't pay a dime for this problem to be fixed, I can only see pain in this path(calling to speak with a tech support representative).
    I also readed that Belkin has bought Linksys, so I don't know if the RV082 will remain with Cisco or will go with Belkin.
    So, my only hope is to document this bug, that is pressent inall firmware version and hardware version of the RV082 as of today.
    many thanks for your help,
    regards,
    Oliver

  • Bug report: A keyboard layout is incorrect on the remote with Hungarian and other "exotic" keyboard layouts

    This is a bug report for Microst Remote Desktop
    ===================================================
    ## Summary
    A keyboard layout is incorrect on the remote with Hungarian keyboard
    ## Version Information, I tested
    * Client
        * Case 1
            * MacBook Pro with HU101 Keyboard
    * Locale: Hungarian
            * Mac OS X Maverics 10.9.2
            * Microsoft Remote Desktop 8.0.6
    * Remote
        * Case 1
            * Windows Server 2003 R2 (English)
        * Case 2
            * Windows Server 2008 R2 (English)
        * Case 3
            * Windows 8.1 (Hungarian)
    ## Detail of bug
    When I connect to the listed remotes the client sets the keyboard layout to Latvian which is a completely different layout than Hungarian (not even close...).
    - On Windows 8 if I set the language on the login screen it stays on that language after the login.
    - On Windows Server 2003R2 and 2008R2 even if I set the language at login it will switch back to LV after the login.
    ## Attachments
    Unfortunately cannot include my shots because I'm not allowed to do this...
    ## End of report
    Please allow the users to set the correct "target" language on connection basis because the automatic method the app use to determine that is unreliable.

    Hi,
    Thanks for the feedback.
    I will forward this to the product team.
    Thanks.
    Jeremy Wu
    TechNet Community Support

  • FAQ: How do I submit a bug report or feature request or otherwise give feedback about Premiere Pro?

    The best way to submit a bug report or feature request is to use the bug-report/feature-request form.
    The Premiere Pro team doesn’t  necessarily see and record every post on every forum and social network, but we do see, record, and track every entry  through the the official feature-request/bug-report form.
    It also helps a lot if you opt into the Product Improvement Program.
    Also, be sure to use the crash reporter.
    We really do read all of the bug reports and feature  requests, and the software really does get a lot of benefit from  detailed crash reports.
    Don’t forget about contacting Adobe Technical Support or Customer  Service, too. For information on how to contact Adobe Technical Support,  see this page. (Note that you must register your product before you can open a technical support case for it.)
    If you have tried to get help from our support staff, but the service  was inadequate, I can help you to escalate your issue if you send me  your case number at kopriva at adobe dot com. You must provide me  a case number. I am not offering to solve your problem myself; rather, I  am willing to forward your information to someone if you have already  hit a dead end with our Technical Support or Customer Service.
    If you have feedback about the content of the Premiere Pro Help document,  then please add a comment at the bottom of the relevant page. You can  add comments to add information, to add links, to make corrections, or  to ask for clarification.
    If you want to keep up with the Premiere Pro team, then you can follow our blogs, Facebook page, and Twitter feed and so on.
    Oh, and I can’t resist this opportunity to remind you to update to  the most recent version of the application. Don’t be surprised when the  first thing that you hear back from us is that you need to install the  latest updates. We fix a lot of things in updates, and we don’t want to go chasing bugs that we’ve already fixed. We’ll keep you posted on our blogs, Facebook page, and Twitter feed about updates as they become available.

    Hi qwerty,
    Dun tink that creative customer support sucks cos I had been dealing with them in the past and I can say that their service are quite gd and fast. If you wanted a refund, I tink you need to contact the store that sells you the product. Dun tink creative will refund you though.

  • Acrobat X Scanning Cancelled Problem / WORKAROUND / BUG REPORT

    As you have read in other threads, Acrobat X on Windows has a serious scanning problem with HP and possibly other scanners.
    Whereas in Acrobat 9 scanning worked reasonably well, Acrobat X seems to be unable to cope with scanning documents from the flat bed of a multifunction scanner.
    So, if you are scanning from the feeder, scanning works, but if you are scanning from the flatbed, you will get a brief pause and the phrase SCANNING CANCELLED.
    This is, of course, not acceptable.
    The problem is that Acrobat X does not play nicely with the scanner drivers.  Previously, Acrobat 9 would "auto-detect" the source of a document, using the feeder if loaded, and "falling back" to the flatbed otherwise.  However, Acrobat X does not fall back.  If there is nothing loaded in the document feeder, the scan will be cancelled by Acrobat X.
    The workaround - and I would NOT call this a "solution" - is to use only the "Custom Scan" command from Acrobat X.  When the window pops up, choose the "Options" button and select "Native Mode" and "Show Scanner's Native Interface" from the two menus.  (Acrobat X does seem to remember these settings at least within a session, so if you're scanning multiple documents you only need to do this once.)  Then scan.
    You will see a new window pop up - the scanner's "native interface."  On my computer, this window shows up BEHIND the Acrobat X screen (annoyingly) so you have to watch for it and click forward.  Be sure to select "flat bed" from the "document source" menu.  On my computer, this setting is NOT remembered between scans, so you have to do this for EVERY SCAN.  Then, the document will scan, and you can do what you want with it in Acrobat X.
    Needless to say, this is a long, painful, slow process, especially if you're scanning lots of flatbed items, as I do.  Hence it's a "workaround" and NOT a "solution".
    The SOLUTION will be for Adobe to FIX this.  ADOBE:  THIS IS A BUG REPORT.  PLEASE LOG THIS IN AND FIX IT.  Acrobat 9 with CS5 worked perfectly, as did Acrobat 8 before it.  Moving to CS5.5 with Acrobat X broke this.  Sloppy.  Please fix!  Thank you!
    Glen Barney

    I used your workaround (thank you!) but it was very annoying. Although I set up the options for a single multi-page document, Adobe gave me separate files and I had to consolidate them. I also had to fill out the options (color, flatbed vs feeder) for each page. This function was working for me at some point, so I don't know what happened to make my HP Multifunction and Adobe part ways. I hope Adobe comes up with a successful patch for this problem.

  • What about a bug reporting mechanism?

    Dear SONY developers an users,
    the overview of the forum indicates that the software of our phones has some bugs. This is normal - no software is bug-free.
    The best known solution in such cases is to introduce some bug reporting and tracking mechanism.
    What do you think about it?
    B.r.
    Glorifyday
    Solved!
    Go to Solution.

    I think this idea has been posted before and it was forwarded internally. I haven't heard anything about it since so I don't know anything about what happened but I'll send it again
     - Official Sony Xperia Support Staff
    If you're new to our forums make sure that you have read our Discussion guidelines.
    If you want to get in touch with the local support team for your country please visit our contact page.

  • Bug report regarding SSL library used by Sharepoint web server

    I have attempted to report this by email to the [email protected] address, but they tell me this is not the correct address to use and have refused to give me a better one or forward my bug report on to the correct people. I'm hoping that by posting it here I will get the attention of someone who can fix the problem.PROBLEM DESCRIPTION:Accessing the Sharepoint web servers (157.55.229.87) is not possible from a Scientific Linux 6.5 system using OpenSSL 1.0.1e. Analysis of the network traffic shows the client successfully connects to the server and sends a TLS handshake. The server responds with a TCP ACK, but does not include a TLS handshake response. After 30 seconds the server tears the connection down with a TCP RST.
    This is reproducable with the following command:
    openssl s_client -showcerts -connect sexeysschool-my.sharepoint.com:443
    DIAGNOSIS:
    The client's TLS handshake contains several length fields - one in the TLSv1 record layer, another in the Client Hello handshake payload and one for each of the cipher suites list and extension list. Each of the length headers is 16 bits long, so should be able to contain any value up to 65535.
    By hand-editing the handshake packet and replaying it, I have discovered that if the value of the TLSv1 record layer length header is <= 255, the Sharepoint server responds correctly. However, if the length header exceeds 255, the Sharepoint server does not respond.
    Under Scientific Linux 6.5, 74 cipher suites (totalling 148 octets) and 5 extensions (totalling 65 octets) are presented by the client, yielding a TLSv1 record layer length of 258 octets.
    Please let me know if I can be of any further help, and if possible it would be useful to have some feedback regarding this issue so that we can keep our customers informed.

    Hi Mark,
    According to your description, my understanding is that the Article Date column displayed with the value based on GMT0 in the Refinement web part.
    Microsoft SharePoint stores date and time values in Coordinated Universal Time (UTC, but also named GMT or Zulu) format, and almost all date and time values that are returned by members of the object model are in UTC format. So the value
    of the Article Date column stores the date and time in UTC format in the database, and the search indexes the UTC value of the Article Date column after crawling the database so that it displays the UTC value in Refinement web part.
    The list column values displayed in the lists that are obtained through the indexer for the SPListItem class are already formatted in the local time for the site so if you’re working on current context list item and fetch a datetime field
    like so SPContext.Current.ListItem["Your-DateTime-Field"] you’ll retrieve a DateTime object according the specified time zone in the regional settings.
    More references:
    http://francoisverbeeck.wordpress.com/2012/05/24/sharepoint-tip-of-the-day-be-careful-when-wor/
    Thanks,
    Victoria
    Forum Support
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact
    [email protected]
    Victoria Xia
    TechNet Community Support

  • Bug Report E71 - Post (serious) bugs here.

    Hi,
    Maybe it's wise to have a dedicated bug report topic for the E71.
    So not discussions here .. just USEFULL reports.
    Bug #1 :
    Situation:
    - I am having a sip internet-call (native SIP client) with an Asterisk server.
    - put the call on 'standby' (by menu Options)
    - i press the 'Options' softkey again
    - phone freezes. Only battery removal can restart it.
    (it also freezes after doing some random key presses .. which i can't remember exactly .. but the standby is not stable.)
    Bug #2:
    - please fix color-settings for the camera . There is 'purple' all over.

    501.21.001 on RM-357 (E71-2) Since upgrading to 501, I've had two major problems. 1) rarely (it's only happened twice), the SMS application will hang when attempting to reply to a message. The original message stays on the screen and nothing will let me out of the app. The phone will respond to the power button, however, and seems to work fine after a reboot. 2) battery life and/or battery meter is terrible. Battery meter will stay near the top then suddenly drop to 2-3 bars remaining. Energy Profiler seems to confirm my power usage is about where it used to be (drawing about 0.12W with the screen off and Gravity running in the background). Phone will then reach 1 bar and give "battery low" warnings, but I'm not convinced the battery is truly low. Last night I was on one bar for over two hours, Gravity was left running, I send and received a few texts, and I was connected to my in-car bluetooth for about 25 minutes, and the phone did not die. On the original firmware, I would never have made it through all that on one bar, which makes me think the bug is with the battery meter, not the battery life itself.

  • Bug Report: Feature Request/Bug Report Form

    Re: Feature Request/Bug Report Form
    https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform
    The Feature Request/Bug Report Form does not include a drop-down option for Creative Cloud.

    Hi Stephen,
    We are collecting feature requests as idea threads here on the forums versus using that form. If you believe you have discovered a bug with Creative Cloud please post about it here on the forums.
    Thanks,
    -Dave

  • Bug report: ignore not working

    Bug report: ignore in the forum here not working
    I set some SPAM users to 'ignore' - still can see their SPAM.
    Please fix it.

    The "Ignore a community user" feature will only block private messages received from other community users. See also the community help here: http://community.skype.com/t5/help/faqpage/faq-category-id/pm#pm
    Is that what you are referring to or do you expect this also to hide public messages posted by these users (which is not what it is currently designed to do).
    If you should spot content on the community that is violating our Community Guidelines please use the "Report inappropriate content" link from the "Post Options" menu next to the message. These abuse reports will then be reviewed by our moderation team.
    Follow the latest Skype Community News
    ↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

  • Bug report: Screen times out when other side is no...

    Bug report: Screen times out when other side is not sharing video. The phone locks and of course the other party cannot see anything. Please fix.
    Using WP 8.1.1 Developers Preview.

    Hi and welcome to the Skype Community,
    Can you please share which platform and which device you are on?
    Also are you referring about a one-way video call here where only you are sending video, but the other party doesn't send their video back?
    Follow the latest Skype Community News
    ↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

  • Sending a bug report on the OS and a sleep mode problem.

    I find the bug button in Safari really convenient for sending Apple bug reports. And when other applications crash, you usually get an error dialog with a button to send a bug report. But sometimes problems arise that require reporting, but which don't fall in either of these categories. It would be very handy to have a bug "button" for the OS, or perhaps just a menu selection in the Finder menu bar that invokes a bug report dialog box. I know you can dig around and find the URL for Apple's bug report web page, but I am always forgetting it -- I suppose I could just bookmark it, but then I'd just have to dig around in all the bookmarks to find it. Better would be a utility built-in to the OS for sending bug reports (like Safari's). It could also automatically transfer necessary info about the OS rev and such.
    The problem I had was this. I have a script that puts my iMac to sleep. I put the script alias on the task bar and a single click puts the computer to sleep (easier than using the menu). Unfortunately, I sometimes click it by mistake when I am trying to click an adjacent icon in the task bar, and the Mac starts going through its cycle to enter sleep mode and is impervious to anything I do to try and cancel it. I tried pressing the space bar continuously to prevent it from going to sleep, but that did not work. Worse, when it went to sleep and I woke it up again, the task bar would not appear, clicking on app windows did not activate them, Finder menus could not be selected, etc. The cursor would move, but I could not do anything else. (I wish now I had noted if the clock in the menu bar was still advancing, but I didn't think to do that.) I powered down the iMac from the power key and rebooted. Things are working fine now.
    I wanted to send a bug report on this, but realized that unlike Safari, there was no button or menu selection for doing that. So here I am.
    Any suggestions are welcome.
    TIA,
    Drake

    [email protected]
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

Maybe you are looking for