Buggy VPN setup

Hi,
I've successfully setup generic ikev2 vpn profile on my z10 and made it to auto connect over mobile network, and link it with my wifi.
Now here is something that I don't understand :
1. On the VPN screen, it says tap profile to edit. It won't happen, and tapping it will always pop up error to connect. Need to click edit and tap.
2. If mobile is switch off, vpn will never be activated even wifi is on and connected to the net. Seems like vpn can only be used when cellular is active.
3. There is no way to tell whether the vpn is active or not other than going back into the setting.
Is this being done on purpose?

Hey DingDang,
To edit the connection you must select Edit at the bottom first, clicking on the profile attempts to connect your VPN.
To see if you are connected, open Network Connections> VPN will say Connected, you can also check the status by selecting the three dots and choose View Status Details.
Do you have a firewall on the Wi-Fi network?This may be why it is not connecting when you are on Wi-Fi only.
Thanks.
-HB
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Similar Messages

  • Remote Access VPN Setup

    Hello Support,
    I have a question regarding a remote access VPN setup with the following. I have a Cisco 6500 with multiple VLANs, and an FWSM setup in mutliple context mode. Each of our clients sits behind their own context, and has their own associated VLANs. Each context has a shared interface, so that one network (our management network) can see all of the networks. We are using a Cisco ASA to terminate P2P VPNs as the FWSms cannot do so, but I would like to setup a remote access VPN from the ASA, but I will need to connect in and have access to all networks. Currently the ASA has an outside interface for internet, two client inside interfaces, and one interface on the shared network.
    If I setup a remote access VPN from the ASA with a separate scope will I be able to see all the networks that I setup routes and nonats for or is there more to it?
    I provided a brief diagram showing all the vlans, I will need to be able to access all of the 6500s vlans when connected using the VPN.
    Thanks in advance for all ideas, suggestions, and assistance.

    Hello John,
    You will need to configure the respective IP Address pool for the Anyconnect users,
    Then create the no_nat rules from all of the internal subnets to the Anyconnect Pool.
    That should do it bud . I mean just make sure the internal network (core) knows that in order to reach the anyconnect pool must send the traffic to the ASA.
    Rate all of the helpful posts!!!
    Regards,
    Jcarvaja
    Follow me on http://laguiadelnetworking.com

  • I do not see where to enter IP addresses in the Open VPN setup. Also, how can I set it up so that I can choose different servers in the same way as I can currently choose them with my VPN app but for PPTP?

    I think I have it working on my iPhone 5. But, I do not see how I can control the exit point that I would like for the VPN. Are all the exit points shown in the VPN setting now going to work with Open VPN, or do they remain PPTP? If I am reading correctly, they look like they remain PPTP. If I cannot control the exit point for open VPN, which exit point is the default in the profile you provided me?I note that Open VPN Connect does not work with any of the new 64 bit devices like the iPhone 5S, the iPad Air, and the new iPad MIni. Is there any chance that you guys will come up with an update for your app so that open VPN can be made to work on all iOS devices? That would be nice, particularly if the Open VPN Connect app does not give me a choice of exit points.Thanks,
    I do not see where to enter IP addresses in the Open VPN setup. Also, how can I set it up so that I can choose different servers in the same way as I can currently choose them with my VPN app but for PPTP?
    Just a quick note to tell you that Open VPN has updated their app so that it is compatible with 64 bit ARM devices like the iPhone 5S, the iPad Air, and the iPad Mini Retina.That does not resolve the problem of how to easily choose among the various possibilities for the exit server. We need to find an easy way to choose.

    Thank you for trying the new Firefox. I'm sorry that you’re unhappy with the new design.
    I understand your frustration and surprise at the removal of these features but I can't undo these changes. I'm just a support volunteer and I do not work for Mozilla. But you can send any feedback about these changes to http://input.mozilla.org/feedback. Firefox developers collect data submitted through there then present it at the weekly Firefox meeting
    I recommend you try to adjust to 29 and see if you can't make it work for you before you downgrade to a less secure and soon outdated version of Firefox.
    Here are a few suggestions for restoring the old design. I hope you’ll find one that works for you:
    *Use the [https://addons.mozilla.org/en-US/firefox/addon/classicthemerestorer/ Classic Theme Restorer] to bring back the old design. Learn more here: [[How to make the new Firefox look like the old Firefox]]
    *Use the [https://addons.mozilla.org/en-US/firefox/addon/the-addon-bar/ Add-on Bar Restored] to bring back the add-on bar. Learn more here: [[What happened to the Add-on Bar?]]

  • To run VPN setup my iphone is requesting for 4 digit pass code ... can you pls assisit?

    To run VPN setup my iphone is requesting for 4 digit pass code ... can you pls assisit?

    Hello RozR,
    We've an article that can help circumvent the new passcode and restore access to your iPhone.
    iOS: Forgotten passcode or device disabled after entering wrong passcode
    http://support.apple.com/kb/HT1212
    Cheers,
    Allen

  • RV120W VPN Setup - basic help needed

    Hi all,
    I've recently bought a RV 120W Wireless-N VPN Firewall hoping it would ease me in creating VPN and remote connectivity. But I seems to be struggling with this.
    Here is my situation.
    When I bought my Cisco router I didn't know it had an ethernet port for WAN. I thought it would have a RJ11 compliant port. So now I am having to put the router behind my modem.
    I gave my modem's LAN 192.168.2.1 and to RV120W I gave 192.168.2.2.
    All PC's are not connected to internet via RV120W. For RV120W, the local IP network is 192.168.1.0. I've set 192.168.1.1 as the management IP of the Cisco RV120W. All the PC's can get internet from the above layout arrangement.
    With frustration, I've portforwared all my ports on the modem (except 1 port) to RV120W i.e to IP 192.168.2.2.
    If I enable PPTP on RV120W I can ping its port (1723 i remember) from outside. If I connect to port 80 from outside my network, I can get the managemnt interface of the RV120W.
    With the help of the RV120W's userguide I managed to create VPN policy stuff via the 'basic VPN Setup' menu. The guides says to use a wizard but there is no wizard for VPN setup.
    With that I have even created users (of every type) but I just can't make the connection.
    When I use the QuickVPN to connect... its goes from "Connecting", "Activating Policy" again "Connecting" and then a big error saying a couple of things that might have caused the error.
    I want to start from the beginning.
    Can somebody please help me.
    First... what I am I supposed to put in the fields of the following screenshot. Especially the fields "Remote WAN's IP Address", "Local WAN's IP Address" and "Local LAN IP Address".

    Once I knew about the bridge mode thing from this discussion, I started reading the manual of the modem in regard to the brigde mode setup.
    According to the manual, the 'Data' bulb on the modem would be off if the modem is in bridge mode. and I've successfully put the modem on bridge mode I guess. It was pretty easy. I just deleted all the WAN setup rules/configs and began with the initial setup wizard which basically had the option to set the modem to bridge mode. After so, the 'Data' bulb got off meaning the modem is now in bridge mode. I am happy about that
    But... still not done.
    I put one ethernet cable into of the LAN ports of the modem and put the other end in RV120W WAN port. Logged into to RV120W, configured new PPPoE profile (I have the user and pass details) and attached it to the WAN internet setup config.
    I went back to the dashboard of RV120W to see if WAN was up. It didn't. I gave some time. It didn't work. It says 'connecting' but never connects.
    What am I doing wrong? Am I putting the cable between the modem and router the right way?
    ...and also, when the modem is in bridge mode will it forward all packets from lan to wan and vice versa or is it like forwarding packets to all ports once recieved.
    (I am learning so much with this RV120W )

  • Simple VPN Setup Fails with "NOTIFY PROPOSAL_NOT_CHOSEN protocol"

    Hi,
    This is pulling my hair out! Must be overlooking something very simple!
    Simple lab setup with 3 routers. VPN setup between R1 & R3 with static routing. R2 connects R1 & R3. All interfaces are reachable, including loopbacks. I am trying to encrypt traffic between loopback on R1 (69.69.69.69) to loopback on R3 (192.168.100.223).
    With no Crypto Map applied to outgoing interfaces on R1 and R3 ping is successful (sourced via local loopback) between the loopbacks. As soon as I add the Crypto Map the same ping fails and and I get the following debug messages.
    When ping initiated via outgoing interface, ping successful!
    *Oct  6 11:44:26.121: ISAKMP: set new node 0 to QM_IDLE
    *Oct  6 11:44:26.125: SA has outstanding requests  (local 103.13.216.8 port 500, remote 103.13.215.236 port 500)
    *Oct  6 11:44:26.129: ISAKMP:(1002): sitting IDLE. Starting QM immediately (QM_IDLE      )
    *Oct  6 11:44:26.133: ISAKMP:(1002):beginning Quick Mode exchange, M-ID of -1381344893
    *Oct  6 11:44:26.137: ISAKMP:(1002):QM Initiator gets spi
    *Oct  6 11:44:26.145: ISAKMP:(1002): sending packet to 172.1.1.1 my_port 500 peer_port 500 (I) QM_IDLE
    *Oct  6 11:44:26.145: ISAKMP:(1002):Sending an IKE IPv4 Packet.
    *Oct  6 11:44:26.149: ISAKMP:(1002):Node -1381344893, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
    *Oct  6 11:44:26.153: ISAKMP:(1002):Old State = IKE_QM_READY  New State = IKE_QM_I_QM1
    *Oct  6 11:44:26.301: ISAKMP (0:1002): received packet from 172.1.1.1 dport 500 sport 500 Global (I) QM_IDLE
    *Oct  6 11:44:26.305: ISAKMP: set new node -1825528760 to QM_IDLE
    *Oct  6 11:44:26.313: ISAKMP:(1002): processing HASH payload. message ID = -1825528760
    *Oct  6 11:44:26.317: ISAKMP:(1002): processing NOTIFY PROPOSAL_NOT_CHOSEN protocol 3
            spi 2376679447, message ID = -1825528760, sa = 670DD6A4
    *Oct  6 11:44:26.317: ISAKMP:(1002): deleting spi 2376679447 message ID = -1381344893
    *Oct  6 11:44:26.321: ISAKMP:(1002):deleting node -1381344893 error TRUE reason "Delete Larval"
    *Oct  6 11:44:26.325: ISAKMP:(1002):deleting node -1825528760 error FALSE reason "Informational (in) state 1"
    *Oct  6 11:44:26.329: ISAKMP:(1002):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
    *Oct  6 11:44:26.329: ISAKMP:(1002):Old State = IKE_P1_COMPLETE  New State = IKE_P1_COMPLETE
    R1
    crypto isakmp policy 1
    authentication pre-share
    crypto isakmp key cisco address 172.1.1.1
    crypto ipsec transform-set TEST esp-3des esp-sha-hmac
    crypto map CRYPTO 1 ipsec-isakmp
    description IPSec Peer to R3
    set peer 172.1.1.1
    set transform-set TEST
    match address ACL1
    interface GigabitEthernet1/0
    ip address 192.250.156.6 255.255.255.0
    no ip route-cache cef
    no ip route-cache
    negotiation auto
    crypto map CRYPTO
    ip access-list extended ACL1
    permit ip host 69.69.69.69 host 192.168.100.223
    R1#sh crypto isakmp sa
    IPv4 Crypto ISAKMP SA
    dst             src             state          conn-id slot status
    172.1.1.1       192.250.156.6   QM_IDLE           1002    0 ACTIVE
    R3
    crypto isakmp policy 1
    authentication pre-share
    crypto isakmp key cisco address 192.250.156.6
    crypto ipsec transform-set TEST esp-3des esp-sha-hmac
    crypto map TEST 1 ipsec-isakmp
    description Primary IPSec Peer to R1
    set peer 192.250.156.6
    set transform-set TEST
    match address ACL1
    interface GigabitEthernet1/0
    ip address 172.1.1.1 255.255.255.0
    no ip route-cache cef
    no ip route-cache
    negotiation auto
    crypto map CRYPTO
    ip access-list extended ACL1
    permit ip host 192.168.100.223 host 69.69.69.69
    R3#sh crypto isakmp sa
    IPv4 Crypto ISAKMP SA
    dst             src             state          conn-id slot status
    172.1.1.1       192.250.156.6   QM_IDLE           1002    0 ACTIVE
    Any help appreciated,
    Thanks.

    Hi Paul,
    "processing NOTIFY PROPOSAL_NOT_CHOSEN protocol 3" indicates the remote VPN peer rejected the phase 2 proposal.
    The configuration snippet you have shared here seems fine, ISAKMP and IPSec debugs (debug crypto isakmp and debug crypto ipsec) from the remote VPN peer will be helpful in troubleshooting further.
    Following is a useful doc on VPN troubleshooting:
    IPsec Troubleshooting: Understanding and Using debug Commands
    Cheers,
    Rudresh V

  • Issues with basic VPN setup and split tunneling

    I have created an SSL VPN to a CISCO ASA 8.6 running ASDM 6.6.
    Im able to connect to the VPN and reach all the devices with the LAN but  Im not able to browse the web. When I enable the split tunnel Im able  to browse the web but then Im not able to reach any internal device.
    Here is part of the show run:
    object network RedInterna
    subnet 150.211.101.0 255.255.255.0
    description Red Interna
    object network NETWORK_OBJ_10.4.1.0_28
    subnet 10.4.1.0 255.255.255.240
    access-list inside_access_in extended permit ip object RedInterna any
    access-list VPN_INTERNET standard permit 150.211.101.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu outside 1500
    mtu inside 1500
    mtu management 1500
    ip local pool VPN_POOL 10.4.1.1-10.4.1.14 mask 255.255.255.240
    failover
    failover lan unit secondary
    failover lan interface fail-1 GigabitEthernet0/2
    failover key *****
    failover interface ip fail-1 10.3.1.21 255.255.255.252 standby 10.3.1.22
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-66114.bin
    asdm history enable
    arp timeout 14400
    nat (inside,outside) source static any any destination static  NETWORK_OBJ_10.4.1.0_28 NETWORK_OBJ_10.4.1.0_28 no-proxy-arp  route-lookup
    nat (inside,outside) after-auto source dynamic any interface
    access-group inside_access_in in interface inside
    route outside 0.0.0.0 0.0.0.0 187.217.68.145 1
    route inside 10.0.0.0 255.0.0.0 10.1.1.78 1
    route inside 150.211.0.0 255.255.0.0 10.1.1.78 1
    webvpn
    enable outside
    anyconnect image disk0:/anyconnect-win-3.1.00495-k9.pkg 1
    anyconnect enable
    tunnel-group-list enable
    group-policy GroupPolicy_VPN_ internal
    group-policy GroupPolicy_VPN_ attributes
    wins-server none
    dns-server value 8.8.8.8
    vpn-tunnel-protocol ssl-client
    default-domain value dominio.com.mx
    tunnel-group VPN_ type remote-access
    tunnel-group VPN_ general-attributes
    address-pool VPN_POOL
    default-group-policy GroupPolicy_VPN_
    tunnel-group VPN_ webvpn-attributes
    group-alias VPN_ enable
    I´m not sure if Im missing some small details or setup. Any help will be highly appreciated.
    Thanks!!!

    Hi,
    When you are using Full Tunnel VPN (which is the default setting) you will have a couple of things that you need to configure on the ASA.
    First, the ASA by default won't allow traffic to enter through an interface and then leave through that same interface. This is what essentially happens when the traffic from the VPN Client comes to the ASA and then heads out to the Internet.  In your case the traffic comes through the "outside" and leaves through the "outside" interface.
    You will need this command
    same-security-traffic permit intra-interface
    You can check if its enabled at the moment with the command
    show run same-security-traffic
    Second, the VPN users will need to have NAT configuration just like any LAN users behind the actual ASA. So you will essentially have to configure Dynamic PAT for traffic from "outside" to "outside"
    You can accomplish that with the following configuration
    object network VPN-PAT
    subnet 10.4.1.0 255.255.255.240
    nat (outside,outside) dynamic interface
    I would imagine that this should do it for you to be able to connect to the Internet and to the LAN network when the VPN is active.
    Hope this helps
    Let me know how it goes.
    - Jouni

  • VPN setup problem

    I have installed Snow Leopard Server on a new XServe. I have updated to 10.6.2.
    Other services are working Related to VPN I have configured the VPN Service using L2TP.
    I have no additional network routing defined.
    Every time I try to setup a connection (from my macbook pro --> running snow leopard 10.6.2) I get the following log messages:
    2009-11-15 14:44:41 CET Incoming call... Address given to client = 192.168.1.160
    Sun Nov 15 14:44:41 2009 : Directory Services Authentication plugin initialized
    Sun Nov 15 14:44:41 2009 : Directory Services Authorization plugin initialized
    Sun Nov 15 14:44:41 2009 : L2TP incoming call in progress from '192.168.1.15'...
    Sun Nov 15 14:44:41 2009 : L2TP received SCCRQ
    Sun Nov 15 14:44:41 2009 : L2TP sent SCCRP
    Sun Nov 15 14:44:41 2009 : L2TP received SCCCN
    Sun Nov 15 14:44:41 2009 : L2TP received ICRQ
    Sun Nov 15 14:44:41 2009 : L2TP sent ICRP
    Sun Nov 15 14:44:41 2009 : L2TP received ICCN
    Sun Nov 15 14:44:41 2009 : L2TP connection established.
    Sun Nov 15 14:44:41 2009 : using link 0
    Sun Nov 15 14:44:41 2009 : Using interface ppp0
    Sun Nov 15 14:44:41 2009 : Connect: ppp0 <--> socket[34:18]
    Sun Nov 15 14:44:41 2009 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : lcp_reqci: returning CONFACK.
    Sun Nov 15 14:44:41 2009 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : sent [LCP EchoReq id=0x0 magic=0x7dd4d1cd]
    Sun Nov 15 14:44:41 2009 : sent [EAP Request id=0x1 Identity ]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoReq id=0x0 magic=0x1e217556]
    Sun Nov 15 14:44:41 2009 : sent [LCP EchoRep id=0x0 magic=0x7dd4d1cd]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoRep id=0x0 magic=0x1e217556]
    Sun Nov 15 14:44:41 2009 : rcvd [EAP Response id=0x1 Identity <"]
    Sun Nov 15 14:44:47 2009 : LCP terminated by peer (Failed to authenticate ourselves to peer)
    Sun Nov 15 14:44:47 2009 : sent [LCP TermAck id=0x2]
    Sun Nov 15 14:44:47 2009 : L2TP received CDN
    Sun Nov 15 14:44:47 2009 : Connection terminated.
    Sun Nov 15 14:44:47 2009 : L2TP disconnecting...
    Sun Nov 15 14:44:47 2009 : L2TP sent CDN
    Sun Nov 15 14:44:47 2009 : L2TP sent StopCCN
    Sun Nov 15 14:44:47 2009 : L2TP disconnected
    2009-11-15 14:44:47 CET --> Client with address = 192.168.1.160 has hungup
    What does that mean:
    "Failed to authenticate ourselves to peer" ???
    Are there some configurations which can solve this problem ???
    Best regards
    Andreas

    This are the related client side log entries:
    Sun Nov 15 14:44:40 2009 : L2TP connecting to server '192.168.1.10' (192.168.1.10)...
    Sun Nov 15 14:44:40 2009 : IPSec connection started
    Sun Nov 15 14:44:40 2009 : IPSec phase 1 client started
    Sun Nov 15 14:44:40 2009 : IPSec phase 1 server replied
    Sun Nov 15 14:44:41 2009 : IPSec phase 2 started
    Sun Nov 15 14:44:41 2009 : IPSec phase 2 established
    Sun Nov 15 14:44:41 2009 : IPSec connection established
    Sun Nov 15 14:44:41 2009 : L2TP sent SCCRQ
    Sun Nov 15 14:44:41 2009 : L2TP received SCCRP
    Sun Nov 15 14:44:41 2009 : L2TP sent SCCCN
    Sun Nov 15 14:44:41 2009 : L2TP sent IRCQ
    Sun Nov 15 14:44:41 2009 : L2TP received ICRP
    Sun Nov 15 14:44:41 2009 : L2TP sent ICCN
    Sun Nov 15 14:44:41 2009 : L2TP connection established.
    Sun Nov 15 14:44:41 2009 : using link 0
    Sun Nov 15 14:44:41 2009 : Using interface ppp0
    Sun Nov 15 14:44:41 2009 : Connect: ppp0 <--> socket[34:18]
    Sun Nov 15 14:44:41 2009 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : lcp_reqci: returning CONFACK.
    Sun Nov 15 14:44:41 2009 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <auth eap> <magic 0x7dd4d1cd> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x1e217556> <pcomp> <accomp>]
    Sun Nov 15 14:44:41 2009 : sent [LCP EchoReq id=0x0 magic=0x1e217556]
    Sun Nov 15 14:44:41 2009 : rcvd [LCP EchoReq id=0x0 magic=0x7dd4d1cd]
    Sun Nov 15 14:44:41 2009 : sent [LCP EchoRep id=0x0 magic=0x1e217556]
    Sun Nov 15 14:44:41 2009 : rcvd [EAP Request id=0x1 Identity ]
    Sun Nov 15 14:44:41 2009 : sent [EAP Response id=0x1 Identity <"]
    Sun Nov 15 14:44:47 2009 : Connection terminated.
    Sun Nov 15 14:44:47 2009 : rcvd [EAP Request id=0x2 EAP KRB <00003f000001000101>]
    Sun Nov 15 14:44:47 2009 : L2TP disconnecting...
    Sun Nov 15 14:44:47 2009 : L2TP sent CDN
    Sun Nov 15 14:44:47 2009 : L2TP sent StopCCN
    Sun Nov 15 14:44:47 2009 : L2TP disconnected

  • OS X server:  VPN setup

    Hi,
       I am using OS X server (10.9.1).   I try to setup VPN service.    But, I do not know what went wrong.    Below is the log.    Any tips?
    1st time:   I use wwmm.wwmmhome.private...
    2013-12-31 14:23:19 SGT     Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:23:19 2013 : Directory Services Authentication plugin initialized
    Tue Dec 31 14:23:19 2013 : Directory Services Authorization plugin initialized
    Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:23:19 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:23:19 2013 : PPTP incoming call in progress from '183.90.37.225'...
    Tue Dec 31 14:23:19 2013 : PPTP connection established.
    Tue Dec 31 14:23:19 2013 : using link 0
    Tue Dec 31 14:23:19 2013 : Using interface ppp0
    Tue Dec 31 14:23:19 2013 : Connect: ppp0 <--> socket[34:17]
    Tue Dec 31 14:23:19 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
    Tue Dec 31 14:23:19 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
    Tue Dec 31 14:23:19 2013 : lcp_reqci: returning CONFACK.
    Tue Dec 31 14:23:19 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
    Tue Dec 31 14:23:22 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
    Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
    Tue Dec 31 14:23:22 2013 : lcp_reqci: returning CONFACK.
    Tue Dec 31 14:23:22 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x38d3186b> <pcomp> <accomp>]
    Tue Dec 31 14:23:22 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x729c77b1> <pcomp> <accomp>]
    Tue Dec 31 14:23:22 2013 : sent [LCP EchoReq id=0x0 magic=0x729c77b1]
    Tue Dec 31 14:23:22 2013 : sent [CHAP Challenge id=0xd5 <663e256443001f6c0163674232734908>, name = "wwmm.wwmmhome.private"]
    Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoReq id=0x0 magic=0x38d3186b]
    Tue Dec 31 14:23:22 2013 : sent [LCP EchoRep id=0x0 magic=0x729c77b1]
    Tue Dec 31 14:23:22 2013 : rcvd [LCP EchoRep id=0x0 magic=0x38d3186b]
    Tue Dec 31 14:23:22 2013 : rcvd [CHAP Response id=0xd5 <63847a83bdb04f9fba56d82397d7213e00000000000000003d68f95fbd5d9f5e90ad10d4e8403c f53e5940402f913a6b00>, name = "test"]
    Tue Dec 31 14:23:22 2013 : sent [CHAP Failure id=0xd5 ""]
    Tue Dec 31 14:23:22 2013 : CHAP peer authentication failed for walter
    Tue Dec 31 14:23:22 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
    Tue Dec 31 14:23:22 2013 : Connection terminated.
    Tue Dec 31 14:23:22 2013 : PPTP disconnecting...
    Tue Dec 31 14:23:22 2013 : PPTP disconnected
    2013-12-31 14:23:22 SGT       --> Client with address = 192.168.1.240 has hung up
    2nd time, I use wwmm.dyndns.org
    2013-12-31 14:38:38 SGT     Incoming call... Address given to client = 192.168.1.240Tue Dec 31 14:38:38 2013 : Directory Services Authentication plugin initialized
    Tue Dec 31 14:38:38 2013 : Directory Services Authorization plugin initialized
    Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:38:38 2013 : publish_entry SCDSet() failed: Success!
    Tue Dec 31 14:38:38 2013 : PPTP incoming call in progress from '183.90.37.225'...
    Tue Dec 31 14:38:39 2013 : PPTP connection established.
    Tue Dec 31 14:38:39 2013 : using link 0
    Tue Dec 31 14:38:39 2013 : Using interface ppp0
    Tue Dec 31 14:38:39 2013 : Connect: ppp0 <--> socket[34:17]
    Tue Dec 31 14:38:39 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
    Tue Dec 31 14:38:39 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
    Tue Dec 31 14:38:39 2013 : lcp_reqci: returning CONFACK.
    Tue Dec 31 14:38:39 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
    Tue Dec 31 14:38:42 2013 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
    Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
    Tue Dec 31 14:38:42 2013 : lcp_reqci: returning CONFACK.
    Tue Dec 31 14:38:42 2013 : sent [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3298b0f1> <pcomp> <accomp>]
    Tue Dec 31 14:38:42 2013 : rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0x5b1829ce> <pcomp> <accomp>]
    Tue Dec 31 14:38:42 2013 : sent [LCP EchoReq id=0x0 magic=0x5b1829ce]
    Tue Dec 31 14:38:42 2013 : sent [CHAP Challenge id=0x5a <4a753b2e091d155a1414337d40401750>, name = "wwmm.dyndns.org"]
    Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoReq id=0x0 magic=0x3298b0f1]
    Tue Dec 31 14:38:42 2013 : sent [LCP EchoRep id=0x0 magic=0x5b1829ce]
    Tue Dec 31 14:38:42 2013 : rcvd [LCP EchoRep id=0x0 magic=0x3298b0f1]
    Tue Dec 31 14:38:42 2013 : rcvd [CHAP Response id=0x5a <2f54770187524125079b5d74e01b09e800000000000000004359e904d9814bc5e0eb4bb880e7e5 23181a0d22b9164e2400>, name = "test"]
    Tue Dec 31 14:38:42 2013 : DSAuth plugin: unsupported authen authority: recved ShadowHash;HASHLIST:<SALTED-SHA512,SMB-NT,CRAM-MD5,RECOVERABLE,SALTED-SHA512-PB KDF2>, want ApplePasswordServer
    Tue Dec 31 14:38:42 2013 : DSAuth plugin: MPPE key required, but its retrieval failed.
    Tue Dec 31 14:38:42 2013 : sent [CHAP Failure id=0x5a "S=8DDCFFC7EA287D3A141E5594392BCBD87C35F76B M=Access granted"]
    Tue Dec 31 14:38:42 2013 : CHAP peer authentication failed for walter
    Tue Dec 31 14:38:42 2013 : sent [LCP TermReq id=0x2 "Authentication failed"]
    Tue Dec 31 14:38:42 2013 : Connection terminated.
    Tue Dec 31 14:38:42 2013 : PPTP disconnecting...
    Tue Dec 31 14:38:42 2013 : PPTP disconnected
    2013-12-31 14:38:42 SGT       --> Client with address = 192.168.1.240 has hungup

    The VPN server in Server.app is these days pretty feeble, it only does PPTP and L2TP and does not support using security certificates or VPN on demand. (Which requires security certificates.) As a result the security of Apples VPN server is only capable of functions which have all been successfully cracked. Now for most people that might not be too much of a concern but if your a law, health, finance, or government customer then it should be a concern.
    However...
    While the VPN server itself does not support clustering nor in fact do any of the services in Server.app there might be a way to achieve what you want. If you have a DNS load-balancer then you can point all the clients to the load-balancer and it will distribute the requests to two or more Apple VPN servers. You just need to make sure each Apple VPN server gives out a different range of IP addresses with no overlaps.

  • PIX 501 VPN setup

    Can any one please advise me I am trying to set up a VPN on my PIX 501 and for some reason it is not working. I have posted the scrips below. If someone can advise me what I need to change that would be great.
    interface ethernet0 auto
    interface ethernet1 100full
    nameif ethernet0 outside security0
    nameif ethernet1 inside security100
    enable password P@55w0rd! encrypted
    passwd P@55w0rd! encrypted
    hostname CFSLXAKALAZ
    domain-name akademic.com
    fixup protocol dns maximum-length 512
    fixup protocol ftp 21
    fixup protocol h323 h225 1720
    fixup protocol h323 ras 1718-1719
    fixup protocol http 80
    fixup protocol rsh 514
    fixup protocol rtsp 554
    fixup protocol sip 5060
    fixup protocol sip udp 5060
    fixup protocol skinny 2000
    no fixup protocol smtp 25
    fixup protocol sqlnet 1521
    fixup protocol tftp 69
    names
    name 192.168.2.0 VPN
    object-group service RemoteDesktop tcp
    port-object range 3389 3389
    access-list inside_access_in remark Allow all outbound UDP port 53 for DNS
    access-list inside_access_in permit udp any any eq domain
    access-list inside_access_in remark Allow ping to any external IP
    access-list inside_access_in permit icmp any any
    access-list inside_access_in remark Allow all outbound TCP connections
    access-list inside_access_in permit tcp any any
    access-list outside_access_in remark Allow external DNS via UDP
    access-list outside_access_in permit udp any eq domain any
    access-list outside_access_in remark Allow ping from outside to inside
    access-list outside_access_in permit icmp any any
    access-list outside_access_in remark Remote Desktop to any internal IP
    access-list outside_access_in permit tcp any any object-group RemoteDesktop
    pager lines 24
    mtu outside 1500
    mtu inside 1500
    ip address outside 10.20.58.30 255.255.255.0
    ip address inside 192.168.2.1 255.255.255.0
    ip audit info action alarm
    ip audit attack action alarm
    ip local pool donkpool 192.168.2.50-192.168.2.60
    pdm location 10.20.58.0 255.255.255.0 outside
    pdm location 192.168.2.0 255.255.255.0 inside
    pdm logging informational 100
    pdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0 0 0
    route outside 0.0.0.0 0.0.0.0 10.20.58.1 1
    access-group outside_access_in in interface outside
    access-group inside_access_in in interface inside
    timeout xlate 0:05:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
    timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
    timeout uauth 0:05:00 absolute
    aaa-server TACACS+ protocol tacacs+
    aaa-server TACACS+ max-failed-attempts 3
    aaa-server TACACS+ deadtime 10
    aaa-server RADIUS protocol radius
    aaa-server RADIUS max-failed-attempts 3
    aaa-server RADIUS deadtime 10
    aaa-server LOCAL protocol local
    http server enable
    http 10.20.58.0 255.255.255.0 outside
    http 192.168.2.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server community public
    no snmp-server enable traps
    floodguard enable
    vpngroup donk address-pool donkpool
    vpngroup donk idle-time 1800
    vpngroup donk password P@55w0rd!
    telnet 10.20.58.30 255.255.255.0 outside
    telnet 192.168.2.0 255.255.255.0 inside
    telnet timeout 5
    ssh 10.20.58.0 255.255.255.0 outside
    ssh 192.168.2.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd address 192.168.2.128-192.168.2.252 inside
    dhcpd dns 158.152.1.58
    dhcpd lease 3600
    dhcpd ping_timeout 750
    dhcpd auto_config outside
    dhcpd enable inside
    terminal width 80
    terminal width 80

    You are missing a lot of config, depending on what type of vpn you are trying to setup please follow the links below to complete it:
    http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/ipsecint.html
    http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html
    http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html

  • Can someone interpret this vpn setup directions?

    http://vpn.bcc.bilkent.edu.tr/mac/
    this is my school's website with the instructions about how to setup the vpn. but im using mountain lion and somehow all my attempts are failing. and options in mountain lion are not the same with the pictures in the website. I think there is no problem with the vpn server because I used it with a pc before.

    Hello TimmyCoogs21,
    I may not be able to give you a direct answer on this. I am not sure of your familiarity with log files. PID refers to a Proceess ID. I am not sure which process has an ID of 94 that is causing you this non-sleep issue. Others have had similar issues in the past, i.e.The HIDD after could possibly mean it is some form of Human Interface Device. If you have a USB or something plugged into your mac at night, or a faulty hardware piece entirely. (These are just speculations)
    Bluetooth drivers prevent system from sleeping in Mavericks - what's going on!?
    Do not let the title fool you as he states that it is not a problem that is caused by bluetooth. Ultimately he sought support from apple, which in your case, I would do the same.
    You could restore/refresh your system and see if this continues if not I would recommend seeking apple support.
    I know this does not fix your problem, however I hope you find some help in it.
    Cheers.

  • Checkpoint VPN setup

    Hi,
    I've got the following issue regarding connecting to a Checkpoint VPN in windows 8.1:
    Message from VPN App: [test]
    Connect: System.Exception: Failed to communicate with the server.
       at CheckPointVpnPluginAppBg.CCC.cccPost(VpnChannel channel, String data, Certificate clientCert, Int32 retryCount)
       at CheckPointVpnPluginAppBg.CCC.cccConnect(VpnChannel channel, Boolean authNeeded)
       at CheckPointVpnPluginAppBg.CCC.snxConnect(VpnChannel channel, StreamSocket socket, VpnRouteAssignment& routeScope, VpnNamespaceAssignment& nameScope)
       at CheckPointVpnPluginAppBg.VpnPlugin.Connect(VpnChannel channel)
    HRESULT 80131500 System.Exception
    What does this mean?
    When I setup the connection and add my certificate, It connects to the server, then I need to supply a password. I get a result back from the server.
    But when it's trying to establish a VPN it gives this error.

    Hi,
    According to your description, let us know your version of Checkpoint VPN.
    Meanwhile, considering that the issue should be related to Checkpoint VPN ,and it is a third-party software, I suggest you contact Checkpoint VPN support for help.
    https://forums.checkpoint.com/forums/index.jspa
    Note: Microsoft provides third-party contact information to help you find technical support. This contact information may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.
    Regards,
    Kelvin hsu
    TechNet Community Support

  • Two RV042 VPN setup

    We are a small business in Indiana and have someone in Idaho connected to us via VPN that does freelance graphic design for us.  She is currently connected to us via a VPN on two Linksys WRV54g routers but our connection is dropped constantly.  I have read online this seems to be a problem so I have purchased 2 RV042 routers to do this since people seem to be much happier with them.  Is there some documentation that will walk me through setting this up?  I will probably want to set them up to be the internet router for the two locations as well (right now in Indiana we have a separate router for that purpose).  We would like to see each other both ways.  She also uses our server as her DNS server since she is in our domain.  Does this make sense?  I know enough to get myself in trouble on this!  Thanks

    There are two ways to do this. one is Gateway to Gateway. This uses two RV042 Router praferably with static or reserved IP addresses on both ends.
    The second is Client to Gateway this uses one RV042 Router and the built in Microsoft VPN Client. This requires one static or reservered IP on your end.     Best way to test this is build it between two internet connections like work and home or if you have two internet connections at work.
    If you chose VPN Gateway to Gateway
    add a new tunnel
    give the tunnel a name like "business name city name"
    chose the LAN port to use WAN1
    next is local group setup.
    I use IP Only
    the router WAN ip address is there and greyed out. take note of this IP
    Local Security Group Type SUBNET
    enter your internal IP segmant. (if you are using 192.168.1.1 then enter 192.168.1.0
    enter subnet 255.255.255.0
    Remote group setup is next.
    again IP only
    enter Her WAN IP address
    Choose Subnet
    then enter her internal IP segmant. note it has to be different then yours. (if you are using 192.168.2.1 enter 192.168.2.0)
    Ike with preshared
    Group 1
    DES
    MD5
    28800 and so on
    Enter the pre shared key and take not of it
    Look at page 36    http://www.cisco.com/en/US/docs/routers/csbr/rv042/admin/guide/RV042_V10_UG_C-WEB.pdf
    Now do the same thing on the other router just revers the local and remote security groups. it is important that the two router are on different Ip segments.
    if you have any question just ask.
    Peter Labelle

  • Which RV220W VPN-setup do I choose in the following situation?

    My RV220W has a fixed IP-address on its WAN and there is an ISP-provided FQDN with reverse lookup available. Is it possible to setup an IPsec VPN on this box that a Mac laptop can connect to the VPN from any location world wide that does not actively block VN traffic in some way?
    I know a PPTP connection to the server on my LAN works, but I'd rather have an IPsec connection to the RV220W and turn the PPTP server on the host inside my LAN off.
    If this is possible, what do I enter where in the wizard?
    I have been unable to get this from the manual or by trying to find a recipe somewhere on the net,

    It explains how to set up the RV220w for IPSec, and connecting using free IPSec clients on both Windows and MacOS.
    https://drive.google.com/file/d/0B0EERf9TN4v1Ym9uaWRlMXhfVGM/edit?usp=sharing

  • ISA570 to RV220 vpn setup

    Good day,
    I need to setup a site to site VPN link between an ISA570 and an RV220.
    I tried using the wizard on the 570 but I still can't get this up.
    The network for the ISA570 is 10.10.0.0/255.255.0.0 and the network for the RV220 is 192.168.5.0/255.255.255.0.
    Both (ISA and RV) have FQDN.
    Would anyone have some screen captures or suggestions ?
    Use to have an old RV082, was replaced by the ISA570.
    Thanks,
    Dan.                  

    http://azure.microsoft.com/en-us/documentation/articles/virtual-networks-setup-hybrid-cloud-environment-testing/
    Okay. Check out if the above link helps you with the setup. If you do not have a VPN device, it might be easy to configure it with RRAS server. What you need to make sure with your big brother is to make sure the pubic IP get routed to the RRAS server (once
    it is setup).

Maybe you are looking for