Button execution issue

I've been having issues with buttons that are tied to my emerson drive talking modbus ethernet. The issue being that when I press a momentary pushbutton, I get a double bump like I hit the pushbutton twice. It'll hold true every once in a while too. In the event log, it reads as followed
cwbutton1 adjusted to on by the control
cwbutton1 adjusted to off by the control
cwbutton1 adjusted to on at the source
cwbutton1 adjusted to off at the source
I'm running lookout 6.0.2. It only happens when I'm connected to a device over modbus ethernet. I'm guessing that I missed something in the setup somewhere. Any help would be appreciated
Haj
Message Edited by Haj on 04-23-2008 08:53 AM
Attachments:
lookout test.zip ‏10 KB

This problem has a long history... I have to say Lookout is designed in this way, although it looks like unreasonable.
You click the button, it turns on "by the control", a write command is being sent. After you release it, it turns off "by the control". But after the ON command is sent, Lookout will read the current value on this register before it sends out OFF command, because Lookout wants to get the ON status if there are any display or control on panel. The button is connected to the register by the remote source, so it will reflect the change on status. So, Lookout reads the ON status back and turns ON the button again "at the source". Then Lookout writes OFF command to device. On the next poll, Lookout reads the OFF status and turn OFF button "at the source".
I know that it doesn't look good in Lookout, we will consider if we need to improve it.
Ryan Shi
National Instruments

Similar Messages

Firefox back button visual issue...

Hey there,
Overall, Firefox is just amazing. I registered this forum just report a bug about the Back-Button visual issue. The Back-Button in Firefox looks broken visually on start. When I open Firefox and enter any website, Back-Button looks visually broken. But later it look okay. I've taken some screen shots about that, but don't know how to attach them here. I am running windows 8 on my computers. Don't know about other OS users, if they are experiencing the same issue or not.

Adapter Description Intel(R) Q45/Q43 Express Chipset (Microsoft Corporation - WDDM 1.1)
Adapter Drivers igdumd32 igd10umd32
Adapter RAM Unknown
Device ID 0x2e12
DirectWrite Enabled false (6.3.9600.17111)
Driver Date 3-11-2013
Driver Version 8.15.10.2702
GPU #2 Active false
GPU Accelerated Windows 0/1 Basic (OMTC)
Vendor ID 0x8086
WebGL Renderer Google Inc. -- ANGLE (Intel(R) Q45/Q43 Express Chipset (Microsoft Corporation - WDDM 1.1) Direct3D9Ex vs_3_0 ps_3_0)
windowLayerManagerRemote true
AzureCanvasBackend skia
AzureContentBackend cairo
AzureFallbackCanvasBackend cairo
AzureSkiaAccelerated 0

Program at print button in 'Issue output to'

Hello Experts,
There is an existing output X which triggers only when output BA00 is printed from the print button in the pop up of sales order when you go to 'Isssue output to'
When trying to process the sales order output BA00 throu standard program SD70AV1A, the output X is not triggered.
Now, we have a requirement to process BA00 from another interface where we are using SD70AV1A, but output X is not triggering in this case.
So, please suggest a way through which we can use the program at print button in this requirement.
Thanks in advance.
Paritosh

Hello Max,
Thanks for your reply
BA00 is printed by program, no issues there. But, there is a requirement on other output X(medium 5) , that it should process immediately along with BA00, which is not happening with this program SD70AV1A.
Paritosh

Button image issues

Im having issues with button images in captivate 4, after designing buttons in photoshop then saving them as PNG's and putting them in the buttons folder. When i apply these buttons to a slide the button images are missing parts and look bad.. any suggestions?, please help.

Hi there
I believe Captivate uses the color value of the pixel in position 0, 0 to determine the transparent color for the button image. You need to ensure you are using a unique color for that location. What you posted seems to infer that you have a color being rendered as transparent and the color is used in other places in the image.
Cheers... Rick
Click here for Adobe Certified Captivate and RoboHelp HTML Training
Click here for the SorcerStone Blog
Click here for RoboHelp and Captivate eBooks

How can I resolve the push button dot issue in oracle forms 10g..?

Hi All,
We have migrated to forms6i to forms10g, in 6i all the push button labels are displaying properly, but in 10g forms its giving dots like this … after displaying some characters. I guess its width problem but how come its changing in 10g alone.
Kindly give me any workaround to resolve this issue
Thanks in Advance
Thangaraj.

Hi All,
We have migrated the forms 6i to forms 10g R2.We are facing push button issue like,the lable is displayed in the button is reduced.Assume the button's label name is Cancel.Actully it is displaying like Can.....Due to Java used in forming the buttons.We have forms count nearly 300.We have diffent size buttons.
We have solution like
1.Manually
2.PC Creation
3.Java Class and Jar Files
4.JDAPI
5.basejini.htm
The method five,we have tried.But there is no changes after this changes also.
Can you guys please let us know the correct menthod(with steps 1 by 1) to do this in quickly.
2.There are look and feel 2 types oracle and generic,rather than this do we have any other type.We are looking for any cusrtomized settings in config files.
Thanks in Advance.
Regards,
GR

Report Execution issues after cube comperssion

Hi Everyone.
We had performance issues with respect to report execution in SAP portal. After the analysis we have realised that the cube is growing in its size and reached 200 million already.
As per SAP suggestion, we had compressed the cube and the reports started running faster than before.
Now, after the release we have realised that some report executions with hierarchy expansion are caused exception in BEX web application.
Below is the error that we receive
When verified the query, we identified that "Active" was set to "Suppress Zeros" query properties and when we modified it is " Active ( All values =0)" it was working fine.
Could not figure out the reason behind this.
Any quick response is much appreciated.

Just wanted to help others on this issue if they face in future.
We are basically in patch 3 and SAP recommended to upgrade the system to patch 10 to solve this issue.
We are still in the process of doing this as it needs approvals, testing etc to be done.
Hope this will be solved after this upgrade and I will post the result in this blog.
Stay tuned .

Scenario/Agent execution issue

Hi Experts
I am using ODI 10.1.3.5
I have 2 scenarios which are scheduled.
Scenario1 Executes multiple times in a day.
Scenario2 Executes once in a day.
Now if i change the time of the scenario2 and do an Update Scheduling in Topology manager, my Scenarion1 execution stops for the rest of the day which affects my data.
Is there any clue to come out of this problem.
regards
Gourisankar

My Package1->Scenario1 is scheduled at 3AM and run in every 4 hours throughout the day. [ *So the cycle will be 3AM , 7 ,11 ,3PM ,7,11 and back to 3 am* ]
My Package2->Scenario2 is scheduled at 3.30AM and will run once in a day. [ *once execution at 3.30 am so no issue* ]
Now if i have to run the scenario2 again at 2.30 PM in a perticular day.
Once i change the scheduling of scenario2 to 2.30PM, i have to do an "Update Scheduling" in topology manager.
[ *Now your Scenario 2 will be executed once at 2.30 pm , so no issue in this but i dont see any reason or way that i affects the scenario 1 execution cycle* ]
Now when i do an "Update scheduling" at around 2 AM, Scenario1 stops executing the subsequent cycle after 2PM for that perticular day.Next day onwords Scenario1 starts at 3AM and executes in every 4hrs.
[ *Here your scenario 1 will again startes at 2AM and so execution cycle wil lbe 2am , 6 ,10 am, 2pm , 6pm, 10 pm and finally 2 am which is not happening ,*
Here Scenario 1 starts at 2 pm and at 2.30 pm scenario 2 starts , which means due to some reason when you update scheduling for scen2 , between 2 and 2.30 pm , the scen 1 execution got changed and went back to default of 3 am cycle , so please check your settings properly .
So can you please check the option of Execution cycle and repetition option and check your starting and ending time too in case you have mentioned
The issue is the perticular day i change scheduling time for another Scenario or same scenario(Scenario1 in this case).
Because last execution cycle for Scenario1 should be around 11.50AM .
[*Going by the details you have mentioned above there is no way the last execution cycle be at 11.50 am it should be rather 11 am* ]

Button Alignment Issue

I have some custom buttons added to the sales order screen. When the font in B1 is set to "10", the buttons show up and are aligned just fine. When the user changes the font to anything other than "10", the buttons become mis-aligned and moved on the form even though I am setting the "Left" property to be the same for all three of them.
Also, on some computers, when the user minimizes the sales order form and then restores the form, all items (even system items) don't resize correctly and the sales order matrix shrinks to about 1/2 the size it was before, leaving a huge empty space on the form. When the add-on is closed, the issue goes away. I am not changing any properties on the system items or the form (width, height etc). I'm just adding three custom buttons and filtering for certain events on the form.
Any ideas?
Thanks!
Message was edited by: Curtis Fry

Curtis,
Did you follow the Standards and Guidelines UI documentation when creating your controls and forms? I am assuming that you did, but there are specifics with respect to the creation of buttons on forms? With other add-ons that you have created, have you experienced this issue?
This is a note from the PartnerEdge Portal that you may want to check out to see if this helps ...
https://websmp130.sap-ag.de/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/smb_searchnotes/display.htm?note_langu=E&note_numm=0000655552
Let me know,
Eddy

Facebook like button widget issue!

I'm working on the website right now. The person wants the Like button on the website, I have yet to deal with it. But I worked on putting it in through the Adobe Widget browser. I like the application because it's click and drag. Yet the issue i'm having is that i want to put the like button in on area where it doesn't over flow in that area. I'm attacthing a screen shot to show the issue.
I'm trying to put the like button on the side bar and I wanted to put it above the events so it's at the top of the page. I'm working it in the sense where it's just the like button and it shows how many people like it. As you can see it makes this big space in the area where it should just be at a space that is smaller then a one enter button push. I tried to fix it through the code but i cant find anything to remove that ammount of the box.

This is exactly what is happening for me right now. Have you figured this issue out yet? Any help would be appriciated. Thanks!

Button rollover issue

Download zipped
FLA
If anyone is bored, I'm having a problem with a rollover
issue in the above movie that I have been creating. It is an
interactive, navigable map of city parks. Rollover of the
individual dots marking park locations on the map works fine. But I
am also trying to list all the parks' names on the right, where you
see the "Bergen Park" button. This is so that the user can either
mouse over the map locations and see the park name
OR
find where the park is located by mousing over the park name
on the right. I want this "Bergen Park" button to cause a section
of the movie clip that has an instance name of "bergen" to play,
making the Bergen Park dot on the map enlarge when the "Bergen
Park" button is moused over. I thought that this actionscript would
do it:
on (rollOver) {
_root.bergen.gotoAndPlay("11");
on (rollout) {
_root.bergen.gotoAndPlay("19");
But it is not working when the movie loads. Only if I mouse
over the Bergen Golf Course dot on the map does the "Bergen Park"
button start acting like a button. Otherwise it just gives me a
text cursor when I mouse over the "Bergen Park" button. Any help
would be much appreciated!
Kevin

had a look at your fla and didn't quite work out exactly what
was "working fine" for you. a few comments on your code:
1. don't you need a stop action on frame 92 ? otherwise it
continues looping.
2. flash is case sensitive - be careful of this - on
(rollout) might work even though the correct syntax is on(rollOut),
but this is because the on handler is ancient syntax (pre dot
syntax). most flash syntax requires you to have the syntax
case-correct.
3. Why is each of your dot clips inside a group? They were
very difficult to find. I can't think of a reason for them to be
inside groups, so I'd recommend selecting all of them and breaking
the group apart so that you can see where they are!
4. The way you've structured your flash file has redundancy
and is going to be a nightmare to make changes to. Imagine if you
or your client decides that they want the dot to pulse twice when
you rollover it. You're going to have to make that small change 42
times. Or even imagine if a URL changes for one of the buttons.
There is a unique line of action-script to open that URL on every
key-frame within the dot movie-clip. so changing a URL would
require making that change on 6 keyframes, let alone the park name
reference to it that you are building on the right. The minimum I
would suggest you do is to have only one movieclip which contains
the animation of the dot pulsing, and then for you to put the
button event handlers on those movieclips, rather than inside those
movieclips. There are even better ways you could go about this, (by
storing the urls and titles in arrays, or even xml, and then
placing the event handlers on the movieclips via their instance
names on one frame of action-script), but this would at least
remove your redundancy.
5. but i digress... to return to your question - the text
cursor appears not when you point to the bergen park button but
when you point to the area between {2, 0} and {502, 20}, because
this is where you created a dynamic text field:
_root.ToolTip.createTextField("TipText", 2, 2, 0, 500, 20);
_root.ToolTip.TipText.type = "dynamic";
add this line after the above code:
_root.ToolTip.TipText.selectable=false;
and your problem should be fixed...

Button Request issue

Hello ,
On a report page, I've created a button item SEARCH, which has "Button Request" set to value : 'SEARCH'.
However, after hiting this button, v('REQUEST') returns null, not 'SEARCH' (as I expected)
Anybody knows why ?
Thank you,

Hello,
>>
Javascript problem in ApEx 3.0 [Solved]
>>
Woooo there lets not get ahead of ourselves, the Pocket PC issue is very specific, if something like this was consistently not setting the REQUEST as designed we would have noticed very quickly as everybodies applications quietly explode.
Try putting this &REQUEST. in your REQUEST attribute of your branch otherwise your REQUEST gets cleared.
See it works like a charm http://apex.oracle.com/pls/otn/f?p=11933:128
If anything this might be a valid request for enhancement to make the default to carry the REQUEST value along, is a tough call because it could adversely effect older applications.
Carl
Message was edited by:
Carl Backstrom

TS4080 apple thunderbolt display image on display intermittently goes dark, does not wake from sleep after clicking mouse or keyboard, but there is "bonk" sound after clicking mouse or pressing keys. Rebooting by pressing the power button resolves issue.

My apple thunderbolt display (which I purchased 1.5 years ago; OS 10.7.5 Mac Mini) intermittently goes dark, does not wake from sleep after clicking mouse or keyboard, but there is "bonk" sound after clicking mouse or pressing keys, so am thinking it is a hardware problem with the display. Rebooting by pressing the power button turns the screen back on, but the same phenomenon has occurred several times. Could this be a software issue, or do I need to have my display repaired? Your feedback would be appreciated.

Hi ED, tough to tell, but it does sound like it's waking with the bonk, just not displaying.
Long shot but...
I wonder if it's a variation of this, of which I've seen many different symptoms...
Resolution
Move the mouse or trackpad cursor over the center area of the login window so you can see the user icons. Click on the icon of the user that you would like to login as, type in the user's password, and press Return.
If the login window is configured to show only the name and password fields, type in the user's name and password into the fields, and press Return (even if you cannot see the rest of the login window).
Additional Information
This issue will not occur if the display is not sleeping when the account is logged out. Use the steps below to confirm that the account is not configured to log out automatically while the display is sleeping:
1. Open System Preferences > Security & Privacy > General. Click the padlock to unlock the preference pane and enter your admin password. Click the Advanced button at the bottom, then see if the option "Log out after N minutes of inactivity" (where N is the number of minutes) is enabled.
2. Open System Preferences > Energy Saver and configure Display Sleep to occur after the account is logged out, by dragging the slider to a number of minutes that is greater than N was set to in the previous step.
Important: If automatic log out is not needed, disable "Log out after Nminutes of inactivity" in System Preferences > Security & Privacy > General. This will also prevent the issue.
http://support.apple.com/kb/TS4135?viewlocale=en_US

Expose / Spaces function(s) fail to work with mouse buttons, ongoing issue

Please see this now very old thread:
http://discussions.apple.com/thread.jspa?threadID=2131775&start=0&start=0
This is an issue as old as snow leopard itself. The problem varies in that it can effect spaces or expose. When using a non-apple mouse, one or more of these functions will fail to perform with a mouse button indefinitely as soon as a restart has taken place.
In my particular case, whatever mouse button I assign to "show desktop" fails to function entirely after a restart has taken place. This remains true even if I re-apply the setting in system preferences, such as changing it to another button, or changing it to nothing, and back. I can still use keyboard shortcuts and screen corners to activate "show desktop". I can continue to use other expose and spaces features with the properly assigned mouse keys. Only one feature, in my case "show desktop", fails to function with -any- mouse button after a restart.
To make this even more clear, this behavior has remained the same and consistent for the 14 months I've had snow leopard. It has even continued to exist after I recently removed and recreated my HFS+ partition, and re-installed OS 10.6, entirely from scratch. It did not exist whatsoever for the year and a month I had OS 10.5 leopard, before upgrading to 10.6. This behavior was +literally introduced upon installing snow leopard+. I have a razer death adder 1500 DPI mouse.
Several others share the exact same symptoms, with only the affected expose/spaces function and mouse model differing. A sibling of mine experienced the +exact same issue+ with an entirely different mac model and the exact same model of mouse.
As a relatively unimportant aside, certain "tricks" seem to fix the issue, but only temporarily (one involves moving the location of spaces and/or expose out of the utilities folder, another involves deleting "com.apple.symbolichotkeys.plist" from ~/Library/Preferences). Unfortunately, these tricks:
A. always only fix the problem temporarily, the issue returns
B. do not address whatever is causing the issue in the first place
This is really frustrating quite a few people, as the linked-to thread can attest to. Along with the obvious, this frustration is magnified because:
A. This issue +does not appear+ to involve terribly challenging technical difficulties (i.e., merely mouse button behaviors).
B. This issue did not seem to exist before OS 10.6.
C. This issue, with the previous two points above in mind, has remained unaddressed for 14-plus months - the entire duration of Mac OS 10.6 snow leopard. I myself originally figured a reasonable time for this issue to be addressed & resolved would be a matter of +a few days+, weeks at most, and at the very least, thought I'd be using these beloved features again +well over a year ago+.
To put it frankly, what the %$#&? Why hasn't this been addressed yet?
Message was edited by: -DrD-
Message was edited by: -DrD-

Anyone even care? I submitted this as feedback to apple, and haven't got a reply through that route, either.

RMS form Button image issue

On RMS forms Button image is not coming. I think this is some confguration issue but i am not able to locate the configuration file which is responsible for this issue.

I think this is a better way to implement your UI:
<?xml version="1.0" encoding="utf-8"?>
<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml">
<mx:Spacer height="2%"/>
<mx:Panel width="55%" height="28%" title="User Details" paddingTop="10">
    <mx:Form>
      <mx:FormItem label="Select account type: " letterSpacing="1"
        fontFamily="Arial" >
          <mx:ComboBox id="accCombo" />
      </mx:FormItem>
      <mx:FormItem label="UserName: " letterSpacing="2" fontSize="11"
        fontFamily="Arial">
        <mx:TextInput id="uname" width="100%"/>
      </mx:FormItem>
      <mx:FormItem label="Password: " letterSpacing="2"
        paddingTop="30" fontSize="11" fontFamily="Arial">
        <mx:TextInput id="password" width="100%" displayAsPassword="true"/>
      </mx:FormItem>
      <mx:FormItem label="Retype Password: " letterSpacing="2"
        paddingTop="30" fontSize="11" fontFamily="Arial">
        <mx:TextInput id="password1" width="100%"
          displayAsPassword="true"/>
      </mx:FormItem>
    </mx:Form>
</mx:Panel>
</mx:Application>
If this post answers your question or helps, please mark it as such.

Button Colour issues...

Hi people.
I'm having some colour issues with my buttons. Not the regular buttons, but the buttons in the picture windows.
http://img.photobucket.com/albums/v520/DanThe440Man/Random%20Stuff/RolloverColou rs.jpg
As you'll see in the 1st picture, 'Back To Index' goes Orange when you hover the mouse over it. When you take the mouse off it, it goes grey. On the 2nd picture, in the bottom right, the 'Next' button behaves exactly the same. This is good, because they fit the colour scheme of the website. However, out of the 9 albums I have on my website, this is the only album that does this. All the other albums buttons are white!
How do I change the colours? I've obviously done it before, but I can't figure out how. Any help appreciated!
Dan

Anybody have any ideas? My sites nearly finished....I'm too fussy to let it go!
Dan

Button execution issue

Similar Messages

Maybe you are looking for