Calculate traffic amount on interface

Team:
I have not deployed any monitoring software yet; however, Cacti is in the works. But is it possible to change ‘five minute input rate / five minute output rate’ time interval from 5 min to secs and get an accurate account of traffic going over a FastEthernet interface? Would I choke the hardware (3750) if I can change this attribute? Would this be a good method to see the load/traffic values in real time?
BACKGROUD:
The server team has deployed a new SQL server, and the DB devs are complaining that it is slow. I am suspecting that more traffic is going over the interfaces then what the ‘server team’ and ‘db devs’ indicated because they know I would raise a stink. I do not have access to the database server, nor the other end, yet I have access to network gear between the points.
Since I have never faced this type of issue, or problem – I need some direction and/or suggestions on how to troubleshoot this type of issue.
Thanks
JJ

Hi Jason,
Issue the command load interval 30 on the interface and it will start displaying the input/output rate for 30 secs.
This won't impact the efficiency of the switch..
For further troubleshooting of the issue check for any output drops/ input errors/crc in the show interface fax/y output.
Thanks
Ankur
"Please rate the post if found useful"

Similar Messages

How to monitor the traffic on network interface card NIC

hello friends
i m dong a network based project
in that i need to calculate the incoming
and outgoing traffic on network interface
Can anyone help me regarding this...
any API that i van use, i know abt JPCAP
but unable to use that in this repect...
Thanks in Advance

sorry for any mistake....
i m new to java
Actually using JPCAP we can capture the packets
and process them..may save to file or some thing like that
but how to know the current incoming and outgoing traffic...on NIC
and also how much it is capable of...
can u tell me any good tutorial
i really need to do that
thanks for concern

How to calculate tax amount

Hi,
I am working in driver program of service sheet entry SF. i want calculate Tax Amount of every line item of service entry sheet number.
tax code, net value, total value mention in line item but tax amount not.
then How to calculate tax amount according tax code...............?

Hi,
Try with the below function module.
CALCULATE_TAX_FROM_NET_AMOUNT
Jshree

Calculate Excise amount as per duty rates check box in J1IEX

Hi,
              In J1IEX Duty rates tab, there is one check box as Calculate excise duty base on duty rates , but thta check box is Disable i How to make it as enable so that we can click to to recalculate the excise rate,
also my problem is that in case of import PO, the basic price in our PO is diffrent compare to basic price of custom . because custom is addding the basic frieght and insurance charges in Basic price, so while Doing J1IEX ref. to MIRO number it is taking properly amount of all excise duties but excise base amount is diffrent and when we correct the excise base amount as per custom Bill of entry all excise amount are change and it is not coming as per duty rates which are present i Duty rates tab so I want to recalculate it.
regards,
zafar

Hi ,
             As per detail which I have mention in my question, the process which we are following is after recieving import Material   first we are doing   MIRO for custom delivery cost   and there we are entering tax amount as per custom bill of entry,   and we are getting the MIRO Documnet number    after that we are Doing    Capture Excise invoice thorugh J1IEX and ref. document we are selecting as PO, after pressing enter we get a small pop up window as customs invocie number and year there we are entering the MIRO document number and Year   then ref. to that miro number All duty and duty rates are coming as per MIRO   but Excise base amount is different because it is coming from PO basic amount and there is diffrence between Custom excise base amount and PO bae amount becasue in custom bae amount they are adding frieght basic amount into excise base amount , and then we have to correct amnually exsice base amount in J1IEX   for all materials, is this proceess is same in all or we need to do some modification in pricing procedure or at any other place .
          At bottom in excsie duty tab in J1IEX there is one check box as Calculates excise amount base on excise duty but that check box is also disable   How to make that enable.
I also have found one FM : J_1IEX_DEFAULT_EXCISE_DUTY,   by doing some changes in this FM we can get what we requied , is there any other solution to get our requirement.
regards,
   zafar
Edited by: zafar_karnalkar on May 15, 2010 1:47 PM

Calculate credit amount based on a sub service order?

Hi Experts,
How do I calculate credit amount based on a sub service order? Is that in the COEP table? If yes what is the logic to calculate it? suppose I have sub service order number 000006009972. Thanks!
Best regards,
- Anthony -

Anthony
It might help if you decribe the business process...
PeteA

How to calculate the amount of viewing the uploaded document in KM?

hello
     everyone
      I want to calculate the amount of viewing the uploaded document in KM,like the iviews of topics in forum.
     thanks in advance
     lexian

Hi,
   You can develop a hitcount repository services. Each time that you open a document this counter is incremented in one. Then you can show this metadata as a typical property.
Take into account:
Dynamic Knowledge Management Content Using Groovy Scripts
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/5165
Documents read statistics
https://www.sdn.sap.com/irj/sdn/thread?threadID=174925
Patricio.

"mpls traffic eng passive-interface" mapping on XR

Dears,
ON IOS for TE-InterAS ,the command "mpls traffic-eng passive-interface" is used on InterAS link which isn't running IGP so i am seeking for the equivlent command on XR but i can't find it so please advise what is the equivlent command on XR
Thanks

Hello Amr,
There is no equivalent command on IOS-XR. Are you trying to set up Inter-AS MPLS TE on XR? In IOS-XR, inter-AS tunnels are supported only by using verbatim path-options. Verbatim path-options are supported on both IOS and IOS-XR.
HTH,
Rivalino

Routing traffice using 2 interfaces

my question is whats the best solution for routing internet traffic out one interface and production, management traffic out another interface. using a cisco ISR 2900

You can use PBR.
Here are 2 documents with examples:
http://www.cisco.com/en/US/docs/ios/12_2/qos/configuration/guide/qcfpbr_ps1835_TSD_Products_Configuration_Guide_Chapter.html
https://supportforums.cisco.com/docs/DOC-1634
HTH

Need to calculate Document amount based on below conditions

Hi Everybody
Here I need to calculate Document amount based on below conditions in the report iam having all the fields.
1)     If the Net Due Date is one or up to tens days less than the document date on any open AP item
2)     If the Net Due Date is "equal to" or "less than" the next month end date on any open AP item
3)     If the Net Due Date is "one day more than" the next month end date on any open AP item
4)     If the "GR posting date" + "payment in days (no of days)" is "one day more than" the next month end date
5)     If the Net Due Date of any open AP item is in Jan., FebDec, place the document amount in Jan, Feb...Dec month
6)     If "Payment date > net due date" from 11 to 30 days add amount
Pls write ur comments if any userexits pls forward to my id
[email protected]
Thanks in Advance
Chaitanya

you can have parameters to pass the points and you can use this inside query to filter and return the required data from query. You can then use this dataset inside chart and plot the points.
http://www.grapefruitmoon.net/ssrs-2008-using-the-top-filter-in-a-chart/
http://blogs.msdn.com/b/florianmader/archive/2013/08/10/sorting-a-chart-by-values-in-ssrs.aspx
Please Mark This As Answer if it solved your issue
Please Vote This As Helpful if it helps to solve your issue
Visakh
My Wiki User Page
My MSDN Page
My Personal Blog
My Facebook Page

Calculate depreciation amount with deduct memo value

Hi ! Guru
I configuration memo value amount with transaction code OAYI and How I set configuration about the system calculate depreciation amount with deduct memo value such as --> acquistition value - memo value / useful life = depreciation amount
How I can do?
thank you very much

Hi,
A) depr. Key LINR, useful liefe 5 years
1. 10.000
2. 8.000
3. 6.000
4. 4.000
5. 2.000
(If you want Scrap value 2.000)
B) You can change the useful liefe in AS02. This is no peroblem. The depr. will be new calculated for open fiscal years.
regards Bernhard

Possible to segment traffic between 2 interfaces? And other questions...

I would like to set my G5 up as a server utilizing a second connection and to keep traffic seperated between this server connection and my regular internet connection (would be wireless). I'm pretty sure this alone is fairly straightforward and can be accomplished by setting up the new interface and moving it down to the bottom of the connection list with wireless at the top. That should keep all non-specific traffic from flowing out the ethernet/server connection - I think.
If the above works the way I stated then I would also want to firewall ONLY the ethernet/server connection (the wireless has it's own hardware firewall). AND - this is the tricky part - I also want to add a fake interface that has a fake IP and bind that to the "real" ethernet/server connection. The reason for that is because I need a static IP to bind the service to. I know if the connection list thing works to flow the traffic that if I had an external router on the server connection, this wouldn't be needed. I'd already have a fake IP to bind to and I wouldn't have to run the firewall on the Mac. But I don't and I'd rather not have to buy one.
So can this be done through the network/sharing preferance panes? If so, are there any "gotchas" I should be aware of? If not, is there any software tool out there that would make setting this up easier/faster? I'm not opposed to doing it all via command line, but I'm a bit rusty with my linux/unix admin knowledge. Plus I'm not 100% certain how to set all that up command line wise without screwing up OS X!
Thanks.

I'm not sure I fully understand what you are attempting to accomplish. Lets see if I have the general idea.
You have a single G5, that you want to use as both your desktop machine and also to provided specific services, such as web, email, etc.
You have some type of hardware firewall/security appliance.
You have some type of wireless access point.
You don't seem to have any type of router or switch in your configuration.
You want all of your server based traffic to be sent and received on it's own Ethernet port. You want your personal Internet traffic to be sent and received on your wireless connection.
So my questions are:
Where is the server traffic going to, coming from? Who is accessing the server, is it users on the Internet, or just computers on your own LAN (which you didn't mention).
If your server is to allow data from or send to the Internet, then you need to have a way to route the traffic there. Do you have more then one method to access the Internet, or will all traffic, both personal and server being going though the same Internet access pipe?
If it is all going through the same pipe, and you only have the single computer, I don't understand why you wish to segment the traffic.
If on the other hand you have multiple computers on your LAN. then segmenting traffic may make sense. This would allow access to your server and keep your LAN well secure.
Anyway, to get to specifics, you'll need to use the terminal app to bind specific services to specific IP's and ports on your Mac. You will also need to manually configure the firewall to be able to select specific connection ports and bindings. However, while I think it can be done, I'm not sure it makes a great deal of sense.
I would be more inclined to suggest a router or switch that can provide VLAN support, or a router that provides true DMZ support, would be a good way to go.
Anyway, a little more info would be helpful.
Oh and if I have this totally worng in what I think your doing.. My mistake.
Tom N.

WCCP on ASA & traffic between physical interfaces on ASA

Hello,
I am trying to get WCCP working on the ASA for WAAS implementation. Here is a simple snapshot of my config:
Eth 0/0 : Outside (to internet)
Eth 0/1 : Vlan1 (20.20.0.0/16) (trunk port to remote office LAN)
Eth 0/1.211 : Vlan211 (20.21.10.0/24)
Eth 0/1.212 : Vlan212 (20.21.20.0/24)
Eth 0/1.220 : Vlan220 (20.22.0.0/16)
Eth 0/2 : WAAS (20.21.30.0/24)
I have the site to site tunnel working. I can ping the WAAS device from the other end of the tunnel but I cannot ping it from the 20.20.0.0/16 network. I have enabled traffic between interfaces on same security level as WAAS and LAN have same security.
I get this error message:
3 Feb 12 2007 17:54:05 305006 20.20.10.101 portmap translation creation failed for icmp src WAAS:20.21.30.230 dst LAN:20.20.10.101 (type 8, code 0)
How can I fix this?
My second question is regarding WCCP on ASA. Here is the WCCP part of the config I have:
wccp 61 redirect-list WCCP_To_LAN
wccp 62 redirect-list WCCP_To_WAN
wccp interface outside 62 redirect in
wccp interface LAN 61 redirect in
access-list WCCP_To_LAN extended permit ip any 20.20.0.0 255.252.0.0
access-list WCCP_To_WAN extended permit ip 20.20.0.0 255.252.0.0 any
I am not seeing any packets being redirected to the WAE. I once changed the access lists to 'any any' and I saw some packets but I couldn't ping or telnet to the remote site. Could it be a loop? Is there any way to exclude traffic to avoid loop?
Thanks
Ankit

common guys
Am I doing something wrong here?
No one replies to my posts. I had the same experience with the previous one.
Is this not the right forum for this query???
Ankit

How to calculate actual amount on PO

Hi,
I have to calculate tax and discount on Purchase order and have add that to ekpo-netwr to get the actual amount. Can you please tell me how to do that?
So far I have been taking the EKKO-KNUMV and going to KONV table and serach for records with that KNUMV. But here I am stuck.
I can not understand (I mean I can not find the field to distinguish) which of the records is actually being used in the PO and has an amount (non-zero) against it, which I see in ME23N in "Condition" at header label.
Reward Points Guaranteed.
Regards,
Anid

Hi,
In the PO , I hope yoy might be using the tax code at item level.
Take this tax code and go to the table A003 and get the KNUMH.
Pass this KNUMH to the KONP table to get the condition value.
Add the condition values to the net amount of the PO item. You will get the total amount.
Alaways find the conditions and taxes at thwew item level of the PO.
Regards,

Discount should calculate on VAT/CST in MM Pricing procedure.? or How to write routine to calculate discount amount after VAT/CST .?

Hi All,
Client is asking discount should calculate after Base+ED+VAT/CST. How to achieve this by configuration or by creating routine?
I am reading Discount amount from condition tab but not able to deduct it after VAT in Routine.

Hi
P is the price of the product
Y is the MRP
P&F = x1.P (x1 of P)
ST = x2.P (x2 of P)
ED = x3 .P (x3 of P)
x1 x2 x3 are constants. P = Y/(1x1x2+x3)
P&F=x1P, ST = x2.P ED=x3P
You have mentioned that all the pricing is based on MRP. Hence you will entering MRP as input price. Now P will be selling price before taxes and discounts. P&F, ST and ED will be always mentioned as % of Product and not MRP. So considering the equation
P + P(x1x2x3)=Y
Hence P = Y (1x1x2+x3) and hence further calculations.
Now in V/08 you can maintain pricing procedure. Here alternate calcualtion type will be routine which you can create new and add to the step.
Hope now its clear.
Kind regards
sandeep

The same condition type calculates different amount !

Hi there,
On the print out of an invoice (VF03) I have realized that two different rows at the end of the invoice with the same description (Min Freight Charge) display 2x different amount of freight, once I check the condition type, on the header level, I see the same condition type (ZS..) with two different amount. Can anybody explain how can the same condition type (Min Freight Charge) be found calculating 2x different amounts
Thanks
Kami

Hi,
Check your pricing procedure at SPRO-> sales and distribution -> Basic functions -> Pricing control ->Define and assign pricing procedures ->maintain pricing procedures.
There might be two condition types used to calculate the frieght value. Each might be assigned with different routines under Alternative formula for condition base value column. I assume only one frieght condition type is needed to calculate the final value with reference to another condition type. Check the settings.
Regards

Calculate traffic amount on interface

Similar Messages

Maybe you are looking for