Can a WLC Control AP's at 2 Sites?

I have 2 sites with 2 IOS AP's each. I would like to use a WLC to control all 4 AP's. I want to have the same SSID at both sites, but have 2 different DHCP servers, one for each site.
The reason that made me think this might be possible is that I have several sites today with their own WLC's and when one WLC failed the AP's from that site immediately connected to a WLC at another site and the users continued getting site appropriate DHCP addresses. Not sure how that happened. I realize the AP's did not have to restart, they just connected to a new WLC at a different site. Hope that is clear.

A WLC can control APs at remote sites by using APs in REAP and H-REAP modes. Just see whether these documents helps you in a way..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00807d4d32.shtml
http://www.cisco.com/en/US/products/ps6521/products_tech_note09186a0080736123.shtml
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008081103d.shtml

Similar Messages

In alv report can i use control break events? if no .whay?

Hi all,
in alv report can i use control break events? if no .whay?

hi,
you can use control break statements in ALV report.
for example: if one PO is having more than one line item, that time you need to display PO only once.

Can we use control events in smartforms

Hi all,
I am srinivas. can we use control events in smartforms, I mean at new, at end of ..... if these are not used can you suggest me any alternative....
Actually my requirement is like a classical report, for which I need to display subtotal and grand totals based on two fields....
Please help me out in this issue as it is very urgent.
<REMOVED BY MODERATOR>
Thanks in advance....
Regards,
Sri...
Message was edited by:
 Alvaro Tejada Galindo

Hi Nick,
 Thanks for the reply... it is really very useful for me.
As I discussed in my earlier mail regarding the output sequence, which should be in the below format.
 number quantity uom unitprice amount curr
plant
 material
 date
 x y z A
 e f g h
 p q r s
 subtotal date..... 1 2 3 4
 subtotal material.5 6 7 8
As you said when I using event of Begin its working fine. but while using the event of end, I am specifying date and then matnr (sort) its taking(nodes are created mean first matnr and then date) in the reverse order and when I am taking matnr and date it is placing the events(nodes) in the right order but the order date is not triggering.
can please tell me how to proceed here..
waiting for your reply..
Regards,
Srinivas

Can some body give me an advice, my cursor can not be controlled after I shut it down, and open again. But this problem goes away after I closed and opened the lid

Can some body give me an advice, my cursor can not be controlled (using pad) after I shut it down, and open again. But this problem goes away after I close and open the lid.

Boot from your OS installer disk and run Repair Disk from Disk Utility.

HT5622 Have Family Mobile with 2 phones and only one Apple ID can all be controlled by the main phone?

Have Family Mobile with 2 phones and only one Apple ID can all be controlled by the main phone?

angiefromaustin wrote:
Yes I know the password for Apple ID.
Then there should be no issue for you.
angiefromaustin wrote:
I do not know the password to get onto the 3G phone to make changes or update apps etc.
Then there is more than one Apple ID involved.... Or a Restrictions Passcode has been set.
angiefromaustin wrote:
2 phones and only one Apple ID
Then what do you mean by this ?

How can I remotely control what iTunes song my iMac is playing to multiple AppleTV's?

So I own an iMac that has homesharing enabled. I then tell the iMac to play to both of my AppleTV's by holding OPTION key down while clicking on Airplay, and checking off the devices that I want it to stream to filling my home with sound that is in sync in every room. Works beautifully. Only problem is that I can not then control the iMac remotely from let's say the bedroom to pick a new artist. The ATV's become dumb clients simply playing what the iMac is pumping to them. Is there a remote interface that allows me to control iTunes on the iMac to choose the sounds being broadcast to the other Apple devices?
NO. VNC is a ghetto work around to accomplish this. Yes, I could do that, but it is inefficient, and inelegant. I am looking for a remote control app with the functionality that allows me to connect to and see the device that I want to control, and then by choosing my iMac, see all artists/albums/songs, play them and let the iMac pump the tunes to the devices that I told iTunes to Airplay to.
Ideally, the AppleTV's should know that they are acting as clients to the iMac serving centrally, but when I pick up an AppleTV remote, it overrides the stream from the iMac, and then the ATV begins streaming independently from the other. I KNOW there is a solution to this...
Any suggestions?
Thanks!
Adam

ok... solved it. By using the Apple Remote app, you can tell the app to control your iMac (I did not know that) and that solved the issue. Now the iMac plays the song I want to all of the devices that I told the iMac to play to. Perfect.

TS1741 I have lost the original remote for my Apple TV. I went to install it at my fiancés house, and cannot use the remote app on my ipad or iPhone. Can I still control the Apple TV with the apps?

I have lost the original remote for my Apple TV. I went to install it at my fiancés house, and cannot use the remote app on my ipad or iPhone. Can I still control the Apple TV with the apps?

Welcome to the Apple Community.
Your Apple TV may have become paired with another remote. Hold the remote close to and pointed at the Apple TV, hold down the menu and Rewind buttons together for 6 seconds or until you see a broken chain icon on screen.

After updating with IOS7, i can no longer control the music on my iPhone with my car controls. I have deleted the phone and re-synced it twice????

After updating with IOS7, i can no longer control the music on my iPhone with my car controls. I have deleted the phone and re-synced it twice????

Go here: http://www.apple.com/feedback/iphone.html and report it with as much detail as possible.

Can I remote control Apple TV without TV screen ever ?

Hi,
all answers I found weren't that clear.
Can I configure & control the AppleTV remotely without using a screen ever ?
Actually, I only want to use it as a mp3 player and I need to control it using:
- mobile phones (iphone but android too)
- OSX
- windows (optional)
Is it possible ?
If the answer is yes: I'm about to buy it right now
Thanks for your answer.
Julien

vazandrew wrote:
Apple TV is a media streamer, meant to be connected to a TV. At the very least you will need a monitor to set up the device. If you are connected to speakers via optical you can then choose to stream Music while TV is off.
If you are simply looking for a way to stream audio, and never intend to use video, then an airport express is a better option.
Ok but I'd have to have a computer for streaming that.
Too bad there is no solution like that with an hard drive for storing music content on it.

Crystal report xi r2 can't show control image

i use vs2008 to develop asp.net
Crystal report xi r2 can't show control image , not show print , export and all control image and when i click
print or export image it error but other control are work. i run web application by debug mode in vs2008
please help me to solve this problem.
thank for advance

Hi,
You are facing issue as you are using non compatible environment.
VS 2003 is only compatible with CR 9.1 (Bundle version which comes with VS), CR XI R1 and CR10.
VS 2005 is only compatible with CR 10.2 (Bundle version which comes with VS), CR XI R2 and CR 2008.
VS 2008 is only compatible with CR 10.5 (Bundle version which comes with VS) and CR 2008 SP0 and SP1
You can download platform supported guide from the following link which will help you to create compatible environment:
[https://websmp105.sap-ag.de/bosap-support]
or search for BusinessObjects note #1279888 - How to find supported platform guide for any platform?
Note can be searched from [here|https://www.sdn.sap.com/irj/sdn/businessobjects-notes]
Hope this helps
Regards,
Shweta

Can i place controls from the properties dialog of an express vi on the front panel?

I'm using the spectral measurements express vi in my vi and I'd like to put the "window" and "number of averages" controls from the properties dialog on the front panel. However, there are not outputs on the express vi icon for these parameters. Can I place controls for these on the front panel somehow or do I always have to go into the block diagram and open the properties dialog to change the values?

The way to do this is to right click on the express VI and select Open Front Panel. This will convert it to a standard subVI. then go into the subVI and replace the Spectrum Averaging and Spectrum Window constants to front panel controls by right click on them. Right click the icon and select Show Connector. Wire the new controls to a free terminal on the connector. You may have to add additional terminals if there aren't any available to wire to the new controls.

Can EM12c Cloud Control agent be installed in a solaris zone?

Can EM12c Cloud Control agent be installed in a solaris zone?
If so, are Solaris 8 and Solaris 9 zones supported?
thanks

Yes we can...
Solaris 9 is supported...I have installed agents on solaris 9 and 10

After install Crystal Report Server 2011, can not access control tools

Afte install Crystal Report Server 2011, can not access control tools from web or from application.
My server OS is Windows 2008 R2 SP1. I follow the default setting. How to fix it?
Error message is above.

Is Tomcat started? On your Start menu you should have an option to get to "Tomcat Configuration" or, under the CRS menu you can run the "Central Configuration Manager" to start Tomcat.
What URL are you using to connect to the web app? By default Tomcat runs on port 8080 so your URL should look something like this: "http://<servername>:8080/BOE/CMC" or "http://<servername>:8080/BOE/BI".
If Tomcat is running and you're trying to access it from another computer, check to see if the Windows Firewall is turned on for the server - if it is, turn it off for "Domain" access.
If Tomcat won't start, go to the folder where Tomcat is installed and then look in the "logs" folder. There should be a file called "stderr.log" which you can open in Notepad to see what types of errors might be occurring (you can ignore any errors having to do with "persisted sessions".) If there are other errors, post in the BI Platform space to get assistance.
-Dell

Why can't I control iTunes windowless with the hotkeys?

You can no longer control Playback options while the window is closed while having the program selected.
This is really annoying.
How do I go back to version 9.2 again?

you might consider to switch to the Mini Player (cmd-Shift-M) instead of closing the Window. The Mini Player reacts to the play back controls.

Can I add controls at runtime in JApplet

Please also tell me what good is JApplet for. As I cannot interact with database and there are several other limitations. Should I go and use JApplet in my application or avoid using them.
My basic question remains the same "Can I add controls at runtime in JApplet"

Yes, you can add controls to an applet at runtime.
Applets are run on remote computers, in browsers for instance.
Since they are run remotely, connecting to a database can be difficult. In most cases you'll need a server that makes the connection with the database. The applet speaks with the server via a socket.
If you're writing a standard desktop application, then you should use JFrame.

Can a WLC Control AP's at 2 Sites?

Similar Messages

Maybe you are looking for