Can an AEBS extend a wireless network and provide 3 LAN ports?

I have just reorganised my wireless network by replacing an AEBS GigE (MC053B/A) {AEBS1} with an AEBS Sim Dual-Band II (MC340B/A) {AEBS2}. Whereas before I used an AE G {AE1} to provide a dedicated G wireless network and bridged it via LAN to AESB1, which was configured for 5GHz N only, the new setup is all taken care by AEBS2.
The setup is basically this:
AEBS2:
- Internet gateway with shared IP from the cable modem.
- all client wireless connections are made to AEBS2, no other base station will accept client wi-fi.
- provides separate 5GHz N and 2.4GHz B/G networks with WPA2 authentication
- performs all DHCP assignment
- uses MAC address access control
- allows networks to be extended
AE1:
- set to 'join' the G network for AirTunes
*AE N* {AE2} :
- set to extend N network but no wireless clients: this enables the LAN port to be used to connect to my FreeSat HD TV's ethernet port, for upcoming BBC iPlayer support.
*Wi-Fi clients:*
- Various client devices all connect via N or G to AEBS2
This all works just fine.
The problem I have is with AEBS1. I have a Mac Min Core Duo that only has G wireless. I would like to configure AEBS1 to extend the N network so that its LAN ports can be used by the Mac Mini (and turn off the Mini's wi-fi). The idea is similar to what I've done with AE2: no wireless clients, just LAN.
I've restored AEBS1 to default settings and then configured it to 'extend' the N network with no wireless clients.
While testing I find that AEBS1 connects to the N network but only for 70 seconds, it then disconnects for 31 seconds, after which it reconnects. This cycle is predictable and I've monitored it from an iMac PINGing AEBS1's wireless IP address while following the ethernet (en0) status in the Console app on a LAN attached MacBook.
The MacBook gets its DHCP assigned IP address from AEBS2 when AEBS1's connection is up, but the IP address is dropped as soon as AEBS1 drops the connection.
The MacBook quite happily connects when I tested it using AE2's LAN port.
So either AEBS1 has a problem, or AEBS2, or both.
Has anyone else experienced something like this?

Thanks Bob. I've read extensively here of the limits of 5GHz, but I've not experienced these as my house doesn't have solid (concrete) floors or (many brick) walls. I also have the main WiFi point upstairs and I've put AEBS2 upside down on its 'head' near the floor.
I'm able to get good Wi-Fi throughout the house on both N and G. The Apple TV, which is under the TV and near AE2 gets good N connectivity. Mainly, the worse WiFi device is the Mac Mini and it always has been.
Since AE2 can join/extend the 5GHz N network and it is downstairs, I think there is some problem with with how AEBS1 tries to extend 5GHz N networks. BTW AEBS1 is on my desk and AEBS2 is under the desk about 1m away.
For the moment I've set AEBS2 to "802.11n only (5 GHz) - 802.11b/g/n" and have AEBS1 set to extend the 2.4GHz b/g/n network. At least the Mac Mini will get 2.4GHz N some of the time and more consistent connectivity all of the time.

Similar Messages

  • Can an Airport extend a wireless network and support a USB printer at the same time?

    Can an Airport extend a wireless network and support a USB printer at the same time?

    Yes, if the AirPort Express is extending the wireless signal produced by another Apple router. The Express cannot wirelessly extend a network produced by a non-Apple router.
    In addition to extending the network and connecting a printer, AirPlay can also be enabled on the AirPort Express, with all services operating simultaneously.
    Please note that only the print function will work if you connect an All-in-One type device to the USB port on the Express. Advanced features like copy, scan, mainentance, etc are not supported when an All-in-One device is connected to the USB port on an AirPort router.

  • Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?

    Can AirPort Extreme join a wireless network and share the connection to ethernet connected devices?

    Yes, if the AirPort Extreme is joining a wireless network that has been created by another Apple router. In this case, it will be extending the wireless network and the Ethernet ports are enabled on the "remote" AirPort Extreme.
    No, if the AirPort Extreme will be used with another router from another manfacturer.
    Ironically, the less expensive AirPort Express can do what you ask about with virtually any wireless network using a special feature called ProxySTA. It won't extend the wireless with a non-Apple router, but the Ethernet port will be enabled.

  • The Difference between Extending a Wireless network and WDS?

    I have an Extreme (n) and an Express (n).
    I want to make sure the signal is strong upstairs and share a printer (connected to the express) and use AirTunes. I also may add an external drive to the Extreme.
    What's the difference between Extending a Wireless Network and using WDS? Will there be a speed difference?
    Message was edited by: J. Christopher Edwards

    I think you don't get it
    If I have another draft N router that operates at 2.4G and I have only n devices I can still use WDS and it will connect using draft n in the 2.4G band.
    If one g device connects to the network will go in mixed mode.
    The AEBS will still report 130 Mbps for your n clients and 54 for your g clients.
    If the other router is g only obviously you can't connect between the two router at n mode but still the AEBS will be in mixed mode and not in g. The Extreme will still report 130 Mbps for the connected n clients.
    I can tell you that because I have actually implemented it am not taking off the documentation.
    The same device if I try to use the "extend n network" does not even see the AEBS but will happily keep the n in the WDS mode and though the bandwidth is halved it is still more than g.
    In any case enough for this!

  • When using an airport extreme to extend a wireless modern, will the lan ports work?

    When using an airport extreme to extend a wireless modern, will the lAN ports work?

    The AirPort Extreme can extend the wireless signal from another Apple wireless router. When it does, the Ethernet ports on the extending AirPort router are enabled.
    Apple's "extend" feature appears to be a proprietary Apple function, so it would be extremely unlikely that an AirPort Extreme...or any other Apple router....could extend a 3rd party router product wirelessly....if that is really what you are asking here.

  • Why can't I extend my wireless network on my Time Capsule?

    So I'm having trouble extending my wireless network in my house with my Time Capsule. I just recently moved into an apartment and had Time Warner install a modem with a bult in router. I then tried to install my TC upstairs and attempted to extend an exisiting network, however my current network doesn't appear on the list of networks to choose from. Why is this?
    *I've read that you cann't extend a network if the original router you're extending from ISN'T an apple router? I'm having a hard time believing that, since all network providers provide you with their own equipment. Any help would be appreciated. Thanks!

    Connect your Time Capsule to your router with an Ethernet cable. That is the only way to "extend" a network created by a non-Apple product.
    *I've read that you cann't extend a network if the original router you're extending from ISN'T an apple router? I'm having a hard time believing that, since all network providers provide you with their own equipment.
    All network providers provide you with the cheapest possible junk. Ask TW how to disable their router and use their equipment strictly as a modem. ISPs have different names for this such as "bridge mode" or "transparent bridging". That way, you can use all the Time Capsule's features.

  • How can I use an Airport Express to join my wireless network and provide an internet signal to my Power Mac g5 via an ethernet cable?

    I have a power mac g5 that does not have a wireless card, and connects to the internet via ethernet cable.
    I want to know how to set up an airport express so that it joins my wireless home network and provides the G5 with an internet signal.
    This via an ethernet cable that is plugged  into the airport express and then into the ethernet port on the g5.
    Please advise as I have configured the airport express in every way possible, the green light is on and when I plug the ethernet cable into the G5 my network cofigurations shows nothing and says that the ethernet cable is not plugged in (It is).
    I get an internet signal if the ethernet cable is plugged directly into my wireless router, so the ethernet port works.
    Please assist. Thanks.

    Two requirements that must be met to do what you want.......
    1) An AirPort Express 802.11n must be used. Check the Model No on the label on the side of the Express. It needs to be A1264. Any other model number will not do what you want.
    2) The Express must be configured to "Join a wireless network" and the option to enable Ethernet Clients must be checked. 
    Open AirPort Utility and click Manual Setup
    Click the Wireless tab below the row of icons
    The box to "Allow Ethernet Clients" must be checked
    Please check to verify that your AirPort Express meets both requirements

  • Can AirPort extend current wireless network and a seperate AirTunes source?

    I currently have an AirPort Extreme Base Station. I would like to have multiple Express base stations set up throughout the house as seperate AirTunes networks. Is it possible to have seperate AirTunes receiving points while at the same time using these Express base stations to extend my current network?

    Thanks. Just paragraph 3 of this article seemed to suggest that you can't have the best of both worlds.
    And other articles only address how to setp up the base station in a client mode without setting it up as a realy station and audio distribution point.
    http://docs.info.apple.com/article.html?artnum=107454
    http://docs.info.apple.com/article.html?artnum=302153

  • Time Capsule - Extend a Wireless Network Disappeared

    I was going in my Time Capsule settings within the Airport Utilities... I wanted to extend my wireless network so I clicked on this option.  When I clicked it... the Time Capsule restarted and now is not showing up in Airport Utilities and there is a flashing amber light on my TC.  Any way I can remove the extend my wireless network and put it back to Join a Wireless network?
    Any help would be awesome...
    Thanks.

    We need a bit more information to understand your setup.
    What version of AirPort Utility are you using?  If you are not sure, open AirPort Utility and click on the AirPort Utility menu at the upper left corner of the screen. Then click on About AirPort Utility. Post back with the version number that you see there.
    The Time Capsule cannot "extend" a wireless network unless it is connecting to another Apple router....an AirPort Extreme, AirPort Express, or another Time Capsule.
    http://support.apple.com/kb/ht1766

  • Can I use a Time Capsule to extend my wireless network.

    Hi, I have just bought a 3TB time capsule as my old (flat style) 500GB TC is reaching full capacity. The old style TC will then be surplus to requirements as a data storage unit, at least for myself, though it might be useful for my son to use as his Time Capsule.
    Ideally, as we have a wireless 'blind spot' out in the rear extension of the house, it would be useful to use the unit to extend my wireless network (and also use it as a separate TC if possible). Is this possible? If it is how would I go about it?
    Hope someone can help . . . .
    Cheers
    John

    Is it possible for you to consider connecting the Time Capsules together using a wired Ethernet connection?
    Here is what Apple has to say in their support document about extending:
    Adding Wi-Fi base stations when it is unnecessary can reduce Wi-Fi throughput because the Wi-Fi network will require more data management overhead. The network configuration also becomes more complex. In the case of a wirelessly extended network, throughput may be reduced to less than 60 percent of that of a single device. The general rule is to keep the Wi-Fi network as simple as possible. You can accomplish this by using the minimum number of Wi-Fi base stations required to service the physical network area and by using Ethernet wherever possible.
    Extending the range of your Wi-Fi network by connecting Wi-Fi base stations together using Ethernet is always the best option, and will provide the best throughput.
    Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations

  • Can I create a unique subnetwork when extending a wireless network using Airport Extreme?

    My office building has an Airport Extreme to provide wifi to our individual suites.  I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers.  Is this possible and how do I do it?  I have currently set up my Airport Extreme in wifi-mode "extending a previous wireless network" and have the router with its unique router name.  But once I extended the wireless network, I could not find the network name of my router, only the office name (the one I was extending).  The computers connected via ethernet to my Airport have internet access but none of my wireless computers see my airport name, it sees the office building network name.  I'm assuming they are connecting to my Airport since the signal level is much higher than before and it appears that my Airport is rebroadcasting the network name of my office building.  Is there a way to have my Airport broadcast its unique identifier for wifi, still connect to the internet via wifi signal to the Office building airport and maintain segregation between my computers and the rest of my office building?
    Also, when I use the Airport Utility on my Iphone, I see the internet -> the office airport extreme -> and then 2 different base stations connected in a Y.  Mine and my neighbors (who is probably doing the same thing as I am).  But there is a dotted line to my base station, does that mean I'm connected to the internet via my neighbor's airport?
    Any thoughts?

    I would like to create a sub-network using my Airport Extreme for my suite only that uses the wifi signal from our office building and provides internet to the computers (both wired and wireless) in my suite but have it protected so that other suites in my building can't see my computers.
    It is not possible to configure a single Apple AirPort router in this manner using wireless only, but it would be possible to do this with a single AirPort if you connect your AirPort Extreme to the "main" router using a wired Ethernet connection.
    As for wireless only....you could probably do what you want by using two Apple routers....an AirPort Express to join the wireless network and provide an Ethernet signal to the AirPort Extreme's WAN port. Then the AirPort Extreme could then be configured to provide a separate network using a different subnet.
    Users on the "main" network would not be able to "see" any devices on your "private" network and vice versa.
    I use the two router set up all the time at hotels that only provide a wireless signal. The first Express "joins" the wireless network and feeds an Ethernet signal to the second AirPort which is configured to "create a wireless network" in router mode.
    This way, I can connect multiple devices to my "private" network, but only pay the hotel for one connection since the hotel router only "sees" the AirPort Express that joins the network.

  • How can I boost signal by extending a wireless network?

    I have an Airport Express serving Wi-Fi and Airplay in my living room, and the signal is just strong enough that my devices will remain connected all the way in my back yard, which would be great for outdoor parties but the signal isn't strong enough to stream reliably. I thought I could resolve this problem by getting a second Airport Express to extend my wireless network and it would act as a repeater. However, it doesn't work when my devices (specifically an iPhone 4S) will not disconnect from the first Airport Express.
    Is there another configuration I can use to get a more reliable Wi-Fi network in my back yard, one that doesn't require stringing an ethernet cable between the Airport Expresses? My base station is stuck in its location since that's where my cable modem and stereo are. Thanks!

    Okay, after further experimentation, it appears the iPhone's Wi-Fi refuses to even recognize the existence of the extending unit. I walked out to the neighboring field, far enough away that the base station's signal cannot reach, but the extending unit still has line-of-sight. The MacBook has about -77 RSSI from the extending unit (verified BSSID is that of the extending unit with Airport Utility) and decent throughput - I was able to load a webpage rapidly - but the iPhone cannot find my network at all.
    I also walked to the far end of the field with the iPhone, power cycled it, and performed Wi-Fi scans as I approached my house. It did not detect my network at all until it could connect to the base station, which I could verify in Airport Utility where it shows the iPhone connected to the base station unit and only the Macbook (still sitting under the extending unit) connected to the extending unit.
    Anybody know how I can fix this so that I can apply the suggested workaround (power cycle the iPhone when outside of range of the base station but within range of the extending unit)?
    Firmware checks verify all devices have the latest firmware. 7.6.1 for the older, extending Airport Express, 7.6.2 for the new hockey puck base station Airport Express, and 5.1.1 for the iPhone.

  • Will extending a wireless network using airport express cause weaker signal?

    Hoping someone can advise on the following please....
    I have installed an Airport Express to extend my wireless network and have confirmed with Apple tech support that it's connected and configured properly. I'm using an Airport Extreme base station as a wireless router.
    The AX does not seem to be extending the signal range at all, and since the setup the signal strenght from the Extreme base station seems to be at half previous strengh.
    Has anyone experienced this please and, if so, what's the fix?
    Any replies gratefully received.
    Regards

    Let's check the settings on your Express. Temporarily, move it to the same room or an adjacent room to the Extreme and power it back up.
    Open AirPort Utility - select the Express - Click Manual Setup
    Click the Wireless tab below the icons and make sure that your settings look like this:
    Wireless Mode = Extend a wireless network
    Wireless Network Name = Same name as the Extreme wireless network
    Check mark entered next to Allow wireless clients
    Wireless Security = Same setting as the Extreme network
    Wireless Password = Same password as the Extreme network
    Confirm Password
    Update to save settings, wait for green light.
    Then move the Express another room or two further away from the Extreme....and restart both the Extreme and the Express. Then perform the BSSID test again.

  • Questions regarding extending a wireless network

    Hi, I have three questions about extending my network.
    1- Is the option "Create a wireless network" on a Time Capsule creating a second wireless network if I use the same name and exact same settings as the wireless network created by an Airport Extreme or just extend it?
    2- If yes, why using the "Create a wireless network" option to extend a wireless network since there's an option to "Extend a wireless network"?
    I've discovered something I don't understand while plugin my Time Capsule. I've set it up using the option "Extend a wireless network" and everything is fine, but if I plug an ethernet cable on my Time Capsule that is relied to my Airport Extreme router that creates the network, I loose all signal.
    3- Why I loose all signal if I connect my Time Capsule to my Airport Extreme via ethernet while my Time Capsule is on "Extend a wireless network" option.
    Thanks!

    1- Is the option "Create a wireless network" on a Time Capsule creating a second wireless network if I use the same name and exact same settings as the wireless network created by an Airport Extreme or just extend it?
    If you have the Time Capsule (TC) connected by Ethernet to another AirPort or non-AirPort router, then this setting will create a second wireless network. However, if both routers are configured for roaming, both of these wireless networks will perform as "one."
    2- If yes, why using the "Create a wireless network" option to extend a wireless network since there's an option to "Extend a wireless network"?
    The "Extend a wireless network" option is for when you want the connection between AirPort routers to be wireless. The AirPort that would be extended would have the option: "Allow this network to be extended" enabled as well. Please check out this Apple Support article for more details on configuring an extended network with two or more 802.11n AirPorts.
    3- Why I loose all signal if I connect my Time Capsule to my Airport Extreme via ethernet while my Time Capsule is on "Extend a wireless network" option.
    It's because you have your network mis-configured for what you are trying to do. Again, that is because this option is only relevant when two AirPorts are interconnected by wireless.

  • How can I extend my wireless network using Airport Express and an Airport Extreme on BT Infinity?

    I have BT Infinity and I am using the Time Capsule with Airport Extreme as my router. Working well (even on wireless). I want to extend the wireless network with an Airport Express, but I cannot work out the settings necessary in Airport Utility. I am using Mountain Lion 10.8.2 on a Mac Pro. Please help!

    BT,
    I've read several of your posts, thanks for taking the time to share your wealth of knowledge.
    I'm in a situation similar to the one described by 'scoutusmaximus'.  Seeking the flexibility of a standalone router, I finally upgraded my 4-yr old ATT DSL gateway (modem+router) to a Comcast standalone modem + the ASUS RT-AC66U: http://www.asus.com/Networks/Wireless_Routers/RTAC66U/
    Typically, I stick with all things Apple but the ASUS router seemed fairly superior to the current-gen base station (on paper, anyway; time will tell when it comes to performance) so, for once, I jumped ship.  My plan was to extend the ASUS wired/wireless network using my TimeCapsule and 2 Airport Expresses in bridge mode, however, a google search turned up several unhappy customers that claim those devices don't play well with non-Apple routers, especially when it comes to 'extending' a network. 
    Questions:
    1. Can I successfully extend the wired/wireless network created by the ASUS router using the 3 airport devices listed above w/out negatively impacting performance?  I'd rather have 1 wireless network as opposed to creating a new wireless network with the TC and then extending it with the AP Expresses... though I'd consider that option down the line if it came to that.
    2. Will the LAN ports on the TimeCapsule remain functional?
    Btw, my house is wired so, I can reach all 3 devices via ethernet cable coming off of a central, managed switch.  Supposedly, you only lose the LAN ports on the TC if you extend wirelessly.
    Any advice would be appreciated.

Maybe you are looking for