Can I use the Airport Extreme Base Station with my already existing D-Link router to increase signal strength?

I already own a wireless router that I would like to keep. Could I use this Airport Extreme Base Station to improve that signal strangth to my room from the living room or to the basement? Would I have to hard-wire both the Base Station and my existing router? You probably have read this question more than once, and I have read some questions of this product too, but for some reason these Apple products I have some trouble with.

Could I use this Airport Extreme Base Station to improve that signal strangth to my room from the living room or to the basement?
Yes
Would I have to hard-wire both the Base Station and my existing router?
Yes

Similar Messages

  • Can I use two airport extreme base station on the same network

    Can I use two airport extreme base station on the same network

    Here is my network setup:
    D-Link DCM-202 simple cable modem (DOCSIS 2.0 compliant)
    attached via ethernet to
    5th generation AirPort Extreme Base Station - Main (Bought last week)
    attached via ethernet to
    4th generation AirPort Extreme Base Station - Remote (Bought about 11 months ago)
    The main AEBS is set to:
    AirPort Section:
    Base Station Tab -> Allow setup over WAN is CHECKED
    Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
    Internet Section:
    Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Share a public IP address
    TCP/IP Tab -> Configure IPv4: Using DHCP
    DHCP Tab -> DHCP Beginning Address: 10.0.1.2, DHCP Ending Address: 10.0.1.200, DHCP Lease: 24 hrs
    NAT Tab -> The box following 10.0.1. is left blank, Enable NAT Port Mapping Protocol box is CHECKED.
    The remote AEBS is set to:
    AirPort Section:
    Base Station Tab -> Allow setup over WAN is CHECKED
    Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
    Internet Section:
    Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Off (Bridge Mode)
    TCP/IP Tab -> Configure IPv4: Using DHCP, IP Address: 10.0.1.2, Subnet Mask: 255.255.255.0, Router Address: 10.0.1.1, DNS Server(s): 10.0.1.1  (Everything else under this tab is blank)
    Hope this helps with info needed.

  • How can I set up the airport extreme base station with windows computer

    how can I set up the airport extreme base station with windows computer

    Hi - you need Airport Utility version 5.6.1 for Windows 7 - go to http://support.apple.com/kb/HT1547  to download it to your computer - the setup depends on what kind of modem you have and if you have another router connected - post back with this info to proceed - thanks

  • Can I use an Airport Extreme Base Station from the USA in Europe ?

    A friend of mine gave me an Airport Extreme Base Station from the USA to Germany. When I hook it up to my PB by ethernet cable the Computer can't find the Base Station at all. If I use my Sonnett Aria Extreme PCI card it finds the station but in the pop-up menu asking in which country I want to use the airport station it only offers North and South American countries. How do I go from here and why is my PB not finding the station when I'm using cables ? Has it something to do with different models for different countries ? Any idea ? Thanx

    Here you go ...
    Changing the Radio Channel on the AEBSn
    Either connect to the AEBSn's wireless network, or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Setup, check these settings:
    AirPort - Wireless
    o Channel: <Use Automatic or select a preferred channel>

  • Can I use the AirPort Express Base Station as a wifi 'reciever'?

    I have a AirPort Extreme base station connect to the internet in my living room. But my bedroom is a little far from the living room so that I cannot revieve a good wifi. I want buy a AirPort Express Base Station to put in my bedroom connecting my PC. Will this way work to make my PC's internet faster??

    Hello:
    You can extend a wi-fi network like this:
    http://support.apple.com/kb/HT4259
    That will not increase speed, but it will improve reception.
    Barry

  • Issue Loading Specific Web Pages Using the Airport Extreme Base Station

    I see that several other members have had this same issue - has anyone resolved their problem? Here is my issue:
    It all started when my wife tried to load her favorite Web page at http://hpana.com - the site now takes well over 5 minutes to load. This started some time after updating the recent security update 2007-009 Version 1.0 and shortly thereafter version 1.1. I have tried using the other Mac computers in the house, using the same wireless network and the same problem presents itself. I have tried loading the page using friend’s computers (Mac and PC, from out side my home) and the page loads within seconds. I have tried using Safari, IE and Firefox (at home), the problem remains. I contacted the hpana.com Webmaster and they have made no changes to their web site.
    I disconnected our cable modem, and connected the modem directly to the iMac (by passing the Apple Airport) and the page loads within seconds. I’m guessing it has something to do with the Airport Extreme.
    So, I contacted Apple Support. The issue was quickly elevated and eventually forwarded to the Airport Extreme Hardware guys – I expect to get an answer by Mid January 2008.
    I took a trip to the local Apple store and after explaining the situation, the store manger replaced the AirPort Extreme with the hope this would resolve the issue. After getting the “new” Airport Extreme up and running … the problem remained. This particular web site hpana.com still takes well over 5 minutes to load. I have no such issue with some of the other 60 or so sites I tried.
    I by passed the “new” Airport once again by connecting the cable modem directly to the iMac and, as before the web page loads within seconds.
    I’ll wait until I get a response from Apple come January, but I was wondering if anyone on the Forum would be willing to share their respective opinions.
    Thank You and Happy Holidays.

    Hi,
    There are some differences between the configuration of Airport equipment sold in different countries, however this is likely to not be the cause of your system's issues. ( See this document for details on that - http://docs.info.apple.com/article.html?artnum=58567 )
    Hong Kong has a very high density of population, especially compared to Australia.. I suspect your wifi signal is probably getting interference from your neighbours wifi, phones and microwaves. There's not much you can do about this, except getting an external antenna for the AEBS and trying to drown them out with it.

  • Can I use the AirPort Extreme to print with my iPhone on a non AirPrint compatible printer

    Can I used this as my new network router and make my printer work with my iPad and iPhone

    In order to print from an iPhone or iPad, your printer needs to be AirPrint compatible.  Check to see if your printer is compatible using this Apple support document:
    http://support.apple.com/kb/HT4356
    Simply connecting the printer to the AirPort Extreme will not make it AirPrint compatible.

  • Configure TC and Airport Extreme Base Stations with different channels

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

    I had to do some serious workarounds to use the Airport Extreme Base Stations as an access point with the same wireless network name primarily due to channel overlap.  I thought I would post my results here since I didnt' find a good article online.
    Also, I found the Snow Leopard verison (5.4.2) of the Airport Setup Utility far superior to Lion's Airport Utility (6.x) in terms of advanced setup. 
    Setup is a 3 flloor house where the 3 wired network locations have wireless overlap.  The problem was that the access points would not hand off the wireless signal because the channels for each airport/TC were automatically set to the same channel.  In non-apple setups, this is how you force a wireless client to switch access points (since the wireless software on your client/mac/windows can detect which access point is stronger and moves to the alternate channel.
    Using apple's "Extend this wireless network" option removes any ability to manually configure wireless channels.  I am writing this from memory, so feel free to ask questions and I will track this topic:
    Procedure
    Setup time capsule as your base station.  Do all the setup for your wireless and guest networks.  Manually configure the network and change the wireless channel to a specific channel for a/b/g networks (e.g., 3) and n networks (e.g, 167).
    Plug your first airport extreme/access point into your wired network.  Do not plug it into the "internet" ethernet plug, use one of the 3 ethernet switch locations
    Use the airport utility to first configure it to "extend" your wired network. 
    Then, go in and reconfigure it manually in the airport utility.  Choose the option to setup a "new network" and name the network the same as the TC wireless network name, security, etc.
    Change the channel from "auto" to a different channel than the TC (e.g., 6 and 137). 
    Now go to the top tab and click on the "internet" icon
    Go to the DHCP tab and change it to "bridge mode."  This will tell the AE to not give out IP addresses (the TC will do this for you).  If you get an error that the IP ranges conflict, you have not done this
    Note that if you have a guest network setup, you will need to set this up on the AE as well. 
    Now test your airport setup.  Take your client (macbook, iOS device) and connect to your network.  Move to a spot near the TC and pull up a web page.  Keep an eye on the signal strength and beginv moving toward the AE.  Refresh the page as you move around.  You should at some point see the signal strength increase.  Refresh your page again.  You should be now connected to to the AE.  I have found that Macbooks do a better job than iOS devices because you get an extra signal bar to measure strength, and they have larger antennas which allows you to better measure problems with handoff
    Another test you can do is to start backing up on your TC and then test the move.  The handoff will truly show you that the TC is handling the process but the AE is relaying to the TC for backup.
    If you need to setup another AE, simply follow setups 3-10.
    I hope this helps others.  I've done this setup 100 times on Linksys devices and although they are cumbersome, they at least allow me to do this setup much more quickly and easily than the apple products. 

  • Can the AirPort Extreme Base Station be plug-in to the power forever?

    Hi,
    sorry for my english but this is my question: Can the AirPort Extreme Base Station be plug-in to the power (electricity) forever? I mean, I don't have to un-plug the Base Station sometimes? Thanks
    Alvaro

    Sounds more like an issue with your router and
    network than a problem with AEBS.
    Which router?
    I certainly do not need to reboot my AEBS like that,
    I think I have rebooted it once in two years!
    I would start a new thread describing your network in
    more detail and the issues with the AEBS.
    Thank you, but my diagnosis is the result of many days
    of experiment with about hundreds of users. It's a bug,
    I know were it is. It was reported to Apple in september
    (2005).
    It isn't that easy to upgrade at the same time all the
    wireless (802.11b and 802.11g) that do have to interoperate
    smoothly within the same space.
    I don't think anyone need to waste more time on these
    bugged firmware versions (5.6 & 5.7) as I already explained
    it. They work smoothly just in a limited environment
    which they were conceived for: one Mac connected to one
    AEBS connected to one FAI.
    You can't recommand these version to colleagues who have
    to live in a real world with other wireless equipment
    (a Mac not updated, an ABS not updated,
    a Cisco wireless card emitting to 100 mW and smashing all
    the neibourhood, a pre 802.11g+ card using 2 channels at
    the same time...).
    dan

  • Using the WAN port as a "LAN" port on the Airport Extreme Base Station...

    Hi everyone,
    I'm re-building my home wireless network and I'm doing so in preparation for the Slingbox AV I ordered last week. Here's my current setup:
    I have a DSL modem attached to an Airport Express (802.11n) in my office broadcasting my internet signal. I have an Airport Extreme Base Station (802.11g) set up in my living room as a WDS extender. I currently use the base station in my living room to connect the DishNetwork ViP722 DVR to the internet and allow me to set recordings remotely on my iPhone when I'm away from home. I use the LAN port on the base station to do this, and now with the Slingbox on the way (should be here early next week), I'm wondering what I need to do to make an internet connection available for the Slingbox AV.
    My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
    Thanks in advance for your advice and insight!

    slugoo wrote:
    My question: Will I be able to simply use the WAN port as a "LAN" port since the Airport Extreme Base Station is being used as a WDS? It'd be awesome if the WAN port would become, essentially, a LAN port since it isn't being used.
    I'd be surprised if that worked. The operation of an AirPort base station depends on keeping the WAN port and the LAN port(s) separate, as those normally are on two different networks.
    You might consider buying an Ethernet hub or switch, which would allow your AirPort Extreme's LAN port to be shared. Here's an example of an inexpensive one:
    http://www.bestbuy.com/site/olspage.jsp?skuId=7169244&st=ethernet+switch&type=pr oduct&id=1110266457435

  • HT1218 After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    After a recent iTunes update attempt iTunes no longer functions and the airport extreme base station is not accessable on our computer.  We still have wifi but cannot access the base station software.

    Thanks for the reply. I appreciate the response. I tried that approach this evening and it didn't work for me. (Technically it worked for me, when I was hardwired into my base station, but would not work for me wirelessly, which is my main issue.)
    Again, using the approach you recommended works only if I have my ethernet cable attached to the LAN port so my computer is communicating directly to the base station through the hard wire. I am able to scan for my base station and make setting adjustments normally this way too.
    As soon as I disconnect from the LAN port and try to go wireless is where I run into problems. The Base Station's wireless network I created is available to choose in the top right corner of the monitor with all of the other available wireless devices/networks -- but the network I created does not have access to the internet. I am also unable to configure my Base Station wirelessly. When my Airport Utility tries to scan for the Base Station and Network, it cannot find any Apple Wireless Device. It's like the Wireless Network in my base station is not sending out a signal.
    Is there a way to resolve this issue?

  • Does firmware update 7.1 break the Airport Extreme Base Station?

    Does firmware update 7.1 break the Airport Extreme Base Station?
    See Digg
    http://www.jayhaynes.net/2007/04/donot_install.html
    April 10, 2007
    Do NOT install AirPort 802.11n Firmware 7.1
    This Firmware 7.1 update for AirPort Extreme Base Station with 802.11n should definitely NOT be installed.
    Here was my problem:
    I used AirPort Utility 5.1 to install the update. It is automatic - launch the utility and it asks if you want to install the update. I said yes because I had problems getting two AirPort n base stations networking together to extend my range (I gave up finally and just used an AirPort Express to extend the range).
    After the firmware update, some sites would not load at all (www.nytimes.com) and others took forever to load. And worse, I could not send any email from any of my IMAP accounts. It seemed to be a DNS problem.
    I have two 802.11n AirPorts, so I finally went back to the other one (7.0) and everything worked fine. The Apple tech support guy offered to replace my broken (7.1) AirPort.
    Foolishly, I wanted to make sure the problem was actually with the 7.1 update and not the AirPort itself. So I updated my second 802.11n base station with 7.1. And it casued the exact same problem (some sites not loading, no outgoing email).
    The Apple tech (at this point I was speaking with a wireless specialist) put me on hold to test a few of his AirPorts to see if he could revert back to firmware 7.0 or (ii) install a clean version of 7.1 (in case the version on my drive was corrupted).
    Unfotunately neither option was possible, which is a design flaw in AirPort Utility.
    Apple is sending me two new AirPorts in 1-2 days, which is great service, but I will not be installing firmware update 7.1 again. Fool me once...
    http://www.apple.com/support/downloads/airportextremebasestationwith80211nfirmwa re71.html
    AirPort Extreme Base Station    

    Turns out that the firmware 7.1 does not render the AEBS useless.
    My problem was resolved when I turned off my DSL modem, the AEBS and the computer. Then restarted in same order going to the next one after the first is compeletly up and running. I had no problems whatsoever after that.
    Seems that the firmware update makes the IPs 'stick' somehow. I would think that even a reset of AEBS might have done it but I never got to that stage.
    All my computers came alive in no time.
    I suggest Smith tries this. Simply reset the whole network. Ah yes, my cable modem has an internal battery, I needed to disconnect this too. Only then did the modem go into the 'acquiring' or 'distribution' mode.

  • Setting Up Comcast to Work with the AirPort Extreme Base Station

    I just set up Comcast high-speed internet through the cable modem and ethernet connection and it works fine. What I need is a step by step instruction on how to set up the connection through my AEBS. I've tried to configure using the Admin Utility, the AirPort Set-Up Assistant, the Network panel---all with no success. I'm not sure what to enter in the boxes or what to check. I've read the "Designing AirPort Networks" PDF and it wasn't much help.
    The AirPort Network was working fine with the dial-up connection I had before.

    Voila! NOT!!!
    I'm having the same problem trying to set up a friend's "new" Macs, and I cannot get them connected to the internet. I've also followed the same steps. I tried the resetting trick (unpluging, waiting, repluging the modem first, then the Airport Extreme Base Station.)
    The DSL ISP is SBCGlobal. Their dsl modem is SpeedStream 5100. The AirportEBS is the about 4 year old white base station with the phone jack, and a WAN and a LAN ethernet ports. I'm trying to connect two iBooks and a MacMini.
    Everything did fine for the past year with the modem in "regular" mode and only ONE Mac connected. When the new Macs were recently acquired, SBC techs said that the modem needed to be put into PPPoE mode so that multiple Macs could be connected at the same time. This was done. [The techs said in regular moden the modem does the authentication; in PPPoE mode the modem acts as a bridge and the AirportEBS is the router and provides the authentication. I am assuming the techs are coreect, but I don't know for sure.] The CAT5 ethernet cable from the modem goes into the WAN port on the AEBS. The computers all see the local wireless network set up by the AEBS.
    However, when any of the Macs try to connect to the internet, the error message returns "No PPPoE server available." Resetting the modem and base station has not cured this. [n.b. Bypassing the AEBS completely by connecting the CAT5 cable from the modem directly to the Mac will provide internet connection.] Any other ideas? Sounds like both of us are having the same sort of problem.

  • I told my wireless network to forget two airport expresses so that I could rename them.  Now the network does not see them even when plugged in about 10 feet away from the airport extreme base station.  Does "forget" mean forever?  How to reset?

    I told my wireless network to forget two airport expresses 1 1st gen, 1 2nd gen so that I could rename them.  Now the network does not see them even when plugged in about 10 feet away from the airport extreme base station.  The network does recognize a totally new 2nd gen express.  Does "forget" mean forever?  How to reset?

    The network does recognize a totally new 2nd gen express.
    Then, it sounds like you have already reset the 2nd Gen Express, and now you need to set it up again, like you did the first time. Only, this time, assign the device name that you want to the AirPort Express.
    Do NOT use the name that Apple suggests.....which will be something goofy like........Sueswimsf's Red Apple AirPort Express
    Assign a simple name.....something like     2ndGenExpress

  • What's the most recent opinion about Time Machine backups to Hard Drives connected to the USB port on the Airport Extreme Base Station (5th generation)?

    I have been searching the Apple communities and Internet for a final answer.  I just bought an Airport Extreme Base Station (5th generation) and LaCie d2 quadra 1TB external drive as a replacement for TWO failed Time Capsules, neither of which Apple would replace due to failed power supplies.  I formatted the 1TB drive using Disk Utility (Mac OS extended (journaled)) from my MacBook Pro, and then plugged into the Airport Extreme Base Station USB port.  The Airport Extreme Base Station see the Hard Drive, and my MacBook Pro sees the Hard Drive in my finder under shared resources.  Time Machine, however, does not see the drive.  Is there a solution for this problem?  If Time Machine will not work, is there another software product out there that will work, like Carbon Copy.  Having to plug the backup drive into the USB port of your laptop every evening kind of defeats the purpose of having a laptop.  Any suggestions would be appreciated.

    Keeping in mind that this is not supported by Apple, I have been successful at doing the following:
    1) Format the entire drive (1 Partition) as Mac Extended (Journaled). You must click in Options and set it as a GUID Partition Table (first option)
    2) Plug drive via USB to AEBS
    3) Using Airport Utility, use Manual Setup, then under Disks, select the new Disk and click File Sharing, then Enable File Sharing and Secured Shared Disks (recommended, of course). Other settings are up to you.
    4) IMPORTANT: you will NOT see this Disk in Time Machine until you open Finder and double-click on it. You will not need to do this again (hopefully).
    5) Now it should appear in Time Machine. Remember to exclude any large files like Virtual Machines, since they will be re-backed-up (is that a word?) every time it changes in any way.
    6) Remember that the first backup (over WiFi) is the longest. Leave the computer alone during this period.
    Good luck, and let us all know how it went for you!

Maybe you are looking for