Can't Connect to SMP on port 8080

Hello,
I have 2 SMP 3.0 SP06 servers, one installed in remote server "azure server"and the other o is installed internally in local server that doesn't have an internet connection.
I can connect to the remote server , I can so the following :
- open admin page
-open integration gateway management page
- telnet port 8080 and port 8083
-register client on application and execute OData services from Advanced REST Client
but when I'm trying to do the same on SMP installed on the local server , I am only able to
- open admin page
- open integration gateway management page
- telnet port 8083 only
but I can't :
- telnet port 8083
- register client on application and execute OData services from Advanced REST Client, as this is done through port 8080.
I executed the command " netstat -a | find "8080" "
and it has the same result on both servers :
screenshot from local server, the other server on azure has the same result.
I have stopped and started SMP services, and still can't connect to port 8080.
I added a role in firewall for port 8080 to allow connection but still same issue, I even disabled the firewall with no hope.
this is screenshot from Advanced REST client, it gives no response after timeout:
screenshot from telnet command:
Am I missing something ?
Thanks,
Hossam

What do you see when you run?
http://localsmpserverip:8080
https://localsmpserverip:8081
when I tried to access the two links :
http://localsmpserverip:8080
https://localsmpserverip:8081
it gives me after timeout this :
but when I tried to access:
https://localsmpserverip:8083
it downloaded a file.
and as I mentioned I can access the cockpit and telnet port 8083.
do you see the same PID for all SMP ports?
" netstat -a | find "8080"
" netstat -a | find "8081"
" netstat -a | find "8082"
" netstat -a | find "8083"
8080 might being used by some other service.
they all used by java.exe and not used by any other process
You can achieve above with HTTPS (secure connection) and 8081 as well.
I tried to register using port 8081 same response :

Similar Messages

Can Prime Infrastructure 2.0 enable port 8080 for Browser access?

By the offical document, port 8080 is pre-defintied for the Browser access but it is disabled by default.
I am finding a way to enable the port, but I cannot find any guide on cisco site.
Did anyone know how to enable the 8080 port?
Thanks in advance.
Louis

HIi Hoi;
As per cisco document : http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1082023
Configuring Server Settings
The Server Settings page allows you to enable or disable the TFTP, FTP, HTTP, HTTPS, or Compliance Service. To turn the server settings on or off:
Step 1 Choose Administration > System Settings.
Step 2 From the left sidebar menu, choose Server Setting.
Step 3 If you want to modify the FTP and TFTP directories or the HTTP and HTTPS ports that were established during installation, enter the port number (or port number and root where required) that you want to modify and click Enable or Disable.
The changes are reflected after a restart.
I am not sure but try to change the port number 8080 in HTTP Forward option and save it, then restart it.
I think it will work.
Regards
Don't forget to rate helpful posts

Can't Connect to SMP 3.0 server from Client

Hello All , I am trying to connect SMP 3.0 server but i am getting error like Requesting Public Key from Server Communications error (14) Connection failed Ending transmission and i also checked with url as per my knowledge its working fine because i am getting message like I am here . I am using below Url . https://Kunal-jit:8082/MobileNorthwind Message : I am here But i think might be SSL certificate issue because its running with red cross. Can you guide ? how to solve ? Thanks & Regards, Kunal Varaiya
Tags edited by: Michael Appleby

Hello Bill ,
SMP Server logs for agentry is below :
15:45:06 06/06/2014: Starting Agentry (64-bit Windows) 15:45:06 06/06/2014: Reading system ini file. 15:45:06 06/06/2014: Starting log file. 15:45:06 06/06/2014: Loading message groups. 15:45:06 06/06/2014: Starting threads. 15:45:06 06/06/2014: 1 initial threads. Threads will auto-scale. 15:45:06 06/06/2014: Event: 0, 2, Loading the Agentry Runtime's public/private key for password exchanges. 15:45:07 06/06/2014: Event: 0, 2, Key pair loaded successfully. 15:45:07 06/06/2014: Starting Agentry: Agentry Server Agent v7.0.3.159 15:45:07 06/06/2014: Event: 0, 2, Agentry Startup 15:45:07 06/06/2014: Loading 0 front ends 15:45:07 06/06/2014: Loading front end from angelvine 15:45:07 06/06/2014: WebSockets Front End: loading configuration 15:45:07 06/06/2014: Event: 17, 14, WebSockets Front End v7.0.3.159 15:45:07 06/06/2014: Starting Agentry Server Agent 15:45:07 06/06/2014: Agentry Server Agent: Starting threads. 15:45:07 06/06/2014: 1 initial threads. Threads will auto-scale. 15:45:07 06/06/2014: Agentry Server Agent: Adding messages. 15:45:07 06/06/2014: Event: 1, 4, Agentry Server Agent v7.0.3.159 15:45:07 06/06/2014: Loading agent from ag3.dll 15:45:07 06/06/2014: Starting Server 15:45:07 06/06/2014: Server: reading config file 15:45:08 06/06/2014: Event: 20, 150, Loading Development application definitions 15:45:14 06/06/2014: Initializing SQL-Northwind from ag3sqlbe.dll 15:45:14 06/06/2014: Northwind Back End: reading config information. 15:45:14 06/06/2014: Northwind: name set to 'SQL Back End'. 15:45:14 06/06/2014: SQL Back End Back End: reading query config information. 15:45:14 06/06/2014: SQL Back End Back End: initialized 15:45:14 06/06/2014: Event: 21, 4, Loaded SQL Back End (SQL v7.0.3.159) from ag3sqlbe.dll 15:45:14 06/06/2014: SQL Back End Back End: connecting 'sa' to database 'Northwind' 15:45:16 06/06/2014: Event: 21, 101, dB Connect 15:45:16 06/06/2014: SQL Back End Back End: started 15:45:16 06/06/2014: Event: 20, 152, Loading Development application definitions for default localization 15:45:16 06/06/2014: Event: 20, 153, Finished loading Development application definitions for default localization 15:45:16 06/06/2014: Event: 20, 151, Finished loading Development application definitions 15:45:16 06/06/2014: Server: Starting threads. 15:45:16 06/06/2014: 1 initial threads. Threads will auto-scale. 15:45:16 06/06/2014: Event: 20, 4, Server v7.0.3.159 15:45:16 06/06/2014: Starting front ends 15:45:16 06/06/2014: WebSockets Front End: Opening WebSockets servlet for sub-URL /MobileNorthwind 15:45:16 06/06/2014: Event: 17, 10, WebSockets Front End v7.0.3.159 15:45:16 06/06/2014: Event: 0, 0, Old log files moved into C:\SAP_SMP\DevSMPServer\Server\log\agentry\rolled\2014-06-06-154506 15:45:16 06/06/2014: Event: 0, 23, Agentry startup is complete.
So based on logs it looks good . but when i try to run URL : https://Kunal-Jit:8081/MobileNorthwind I am getting SSL Connection error (I also followed steps provided by last post). ATE : Communication error 14
Can you please guide ? How to solve ?
Thanks & Regards, Kunal Varaiya

Can I connect hdmi and display port at the same time?

The toslink on my 2010 mini is glitchy. So I want to run the audio through the hdmi to my recevier. And the video through the minidisplay port to hdmi to a monitor. Will this work? Can I use the hdmi for audio only and the display port for video only? Thanks

Yes, that is exactly how to use dual monitors.
Optionally:
if the second monitor has DVI input, use the MiniDisplay Port to DVI adapter.
or if it has Display Port input, then all you need is a straight MiniDisplay Port to Display Port cable.
In Quick Links try Account if Sign In does not work.

Can you connect a iPad USB port into a TV and show the videos you play?

Can you sue the USB to plug into a TV and show the videos?

Sorry I meant USE not SUE.

I have a PCI-FBUS card (dual port), can't connect over 60 devices to it?

I connect to various Fieldbus devices (all from the same manufacturer and same type as we are an OEM) that I am testing (I have 80 in my test system). I have the dual port PCI Fieldbus card and am running communication manager 3.2 on Windows XP with service pack 2. As part of my pretest (getting the devices on the bus and assigning them a unique address) I connect to a device and change its address to 20 and power off the device to have it drop off the bus then relay in the next device and connect to it and change the address to 21 etc etc---this process makes it easiest for me as then all I have to do is connect to the only device on the bus and know that it is the device I am interested in assigning to it a new unique address as the others are not on the bus. I am able to get 30 devices per port (60 devices total since I have a dual port card). After the 30th device is connected, albeit no devices show up on the bus since they are all powered off, I relay in my 31st device but I can't connect to it on a given port (at this point I have 30 devices that were connected to each port but are now powered off). I have the card configured to operate within the address range of 16-102 for both ports.
What is the limit of the number of devices that can be connected to a given port? What would be the recommended way of connected say 80 devices to a PCI card (40 per port). For my application, after the so called pretest is complete, I do have to have up to 8 devices powered on at the same time (4 per port) so that is why I want to keep the addresses unique per device. By the way I know this is not a physical connection issue with my station as I can connect to all devices when I limit my test to 60 devices (i.e. I can do the first 60 or the last 60 so the wiring etc is good as well as my assigned address space/parameters for the NI card).
Some of My NI card parameters are,
Dlme Link Master Info,
Dlme Scheduling Overhead 4
Def Min Token Deleg Time 84
Def Token Hold Time 700
Target Token Rot Time 4096
Link Maint Tok Hold Time 0x0
Time Distribution Period 5000
Max Inactivity to claim Las Delav 100
Las DB Spdu Distri Period 200
System Management Info,
Primary Time Master 0x10
T1 0x75300
T2 0x2bf200
T3 0x15f900
Clock Sync Interval 10
Dlme Basic Info,
slot time 8
Slpdu Phl Overhead 0
Max Response Delay 10
First Unpolled Node 0x66
Number of Unpolled Node 0x79
This link 0
Min Inter-Pdu Delay 16
Preamble Extension 0
Post Trans Gap Extension 0
Max Inter Chan Signal Skew 0
Time Sync Class 1ms
Thanks
Jim

Hello Jim,
In NI-FBUS, the max number of devices that can be connected to a segment (port) at one same time is 32. This value is defined by FF specification.
Please try the following method.
After connecting the 30th device, restart NI-FBUS Communications Manager (CM), then connect the 31th device. Check whether the problem still occurs.
Regards
Feilian (Vince) Shen

LC Configuration Manager problem, port 8080 still in use?

I'm installing a trial version of the Adobe LiveCycle ES server using JBoss on my system for some development. I'm running Windows Vista Ultimate 64-bit. I did a turnkey installation. That goes fine. When I run the configuration manager, it gets to the deployment step and the "Verifying ports required by service JBoss for Adobe LiveCycle ES are available" step, and I get this error:
"The following ports required by JBoss for Adobe LiveCycle ES are still in use 8080.
Another instance may be running or another application may be using some of the required ports."
Nothing has port 8080 bound. I've checked with a netstat -a -o command. I can run tomcat and it binds port 8080 just fine. I've disabled UAC (I'm logged in as an administrator), disabled windows firewall, and even uninstalled and reinstalled livecycle. One thing that happens if I restart my computer and try again is that it fails for a different error about being unable to stop the JBoss service. If I stop the service manually and retry, it just reverts to the port error above.
This error is really confusing and I can't seem to figure out how to fix it. I need to get this up and running so I can develop and test my application. Anyone have any insights or suggestions?
-Sam Fahmie

I have the same problem trying to install on Vista64. Perhaps it only works on XP and 2003?
"Chances are that the installer is failing at the stage where it tries to create a Windows service for JBoss and fails"
This isn't the installer, it's the configuration manager that runs after the installer.
The installer creates the service just fine. It's when the manager tries to start the service that it fails. If you manually start jboss then run the configuration manager again then it stops at the same point complaining that an instance of jboss is already running. If jboss is already running, why doesn't the installer just skip that stage and continue?
I've found that after starting jboss manually I can connect to the 8080/adminui page (took a very long time to respond the first time I connected), but the default login doesn't work. I assume some extra steps haven't been done. Is there any way to bypass the starting of jboss in the config manager in order to complete the other steps?
I've also tried launching the configuration manager bat file from an administrator mode console, but it fails at the same point.
2 days screwing around with this software, both turnkey and manual on Linux and I haven't managed to get it to work. Quality. Next step will be to see if I can get a copy of XP from the museum and a find machine to run it on.

Wake up on port 8080 access

Hello,
I have a Mac mini, and I have configured it to wakeup on network access. It plugged to my router by a physical cable (not using wireless).
I noticed that I don't need to send a WoL package: if I just try to connect by SSH (port 22), it wakes up.
I wondered if there is any way I could configure it to also wakeup on port 8080 access.
(Basicly, I have sabnzbd installed on my mac, and flexget running on my router. I want flexget to be able to wake up my Mac just by accessing sabnzbd).
Regards,
Eduardo Antunes

Well... I have a Asus RT-N56U router, running a thrid-party firmware (http://code.google.com/p/rt-n56u), with optware installed. I have search for it, but I don't think either RT-N56U or optware offers sleep proxy suport.
But I also have a Apple TV, which I have read somewhere can act as a Sleep Proxy (maybe that's what waking up my Mac when I try to ssh it).
Do you know how I can configure my Mac to advertise port 8080?
Thanks for the reply.

How can I connect my thunderbolt on mac book pro

How can I connect my thunder bolt port, it is sayinng that it is not connected

Model Name: MacBook Pro
Model Identifier: MacBookPro8,3

How to detect what's using port 8080

I'm getting this error when runing my ANT script:
[java] LifecycleException: service.getName(): "Catalina"; Protocol handler start failed: java.net.BindException: Address already in use: JVM_Bind:8080
wonder how can I tell what's using port 8080.
thanks

windows:
c:\netstat -an | find "8080"
*nix:
netstat -an | grep "8080"

Fire fox can,t establish a connectionat port 8080. unable to connect.

i have using apache- tomcat-6.0.32...src and jdk1.6.0
when i writ http://localhost:8080/ then it not display any answer for tomcat server....it display that firefox can't establish aconnection at port 8080 and unnable to connect..
so plz solve my problem as soon as possiblle ..and reply...i will wait..thanku

"Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove the Cookies" from sites that cause problems: Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

How can I connect my 3gen apple tv with HDMI to my bush LCD32TV022HD which does not have an HDMI port but does have 1)S-Video I/P, 2)Video I/P, 3) L

How can I connect my 3gen apple tv with HDMI to my BUSH LCD32TV022HD
This does not have an HDMI port but does have:-
1) S-Video I/P,
2) Video I/P,
3) Audio Input (Left & Right)
4) Audio In jack (for VGA and DVI source)
5) DVI input
6) VGA input

Welcome to the Apple community.
The Apple TV doesn't officially support a DVI connection, however you may be able to get it to work. You will first need to check that your TV supports either 720p or 1080p as well as HDCP. If you are able to get the video working over the DVI connection, you may also require a DAC in order to connect with Apple TV's optical audio output to the TVs audio imput.
You may well wish to make sure that the DVI connection works before spending any money on a DAC..

How can I connect multiple devices to Mac mini display port? I need to connect a Canon 5D to my Mac and display the result on a VGA video projector. I am using mini hdmi to mini display for the camera. Can I connect the VGA to any other port?

Hi there I am connecting a Canon 5D to my laptop trying to use it as a webcam trough camtwist.
At the same time I need to output the streaming to a videoprojector.
The cam is connected to the mini display port do there is no port available for the VGA cable anymore.
Do I need to use a different port for the projector? Should I buy a video card?
Can't connect the camera via USB as that is too slow and it will freeze.
Many thanks for all your help
Best
Faeve

You might do better on a forum other than this one, which is "Using iPhone"

How to connect A extreme to A express in WDS so i can use A express as LAN port with RJ 45. A express is old and does allow WDS, but A extreme is n technology and doesnt allow wds anywhere in configuration. do i hvae to buy a new A extreme or new A expr

I have an airport extreme 4th generation (n) and airport express i think model 1084, which is not n technology. I want to connect the express to extreme base station wirelessly and then use the port on express to connect a non wireless PC or TV to the internet. I do not want to run a wire from base station to the computer and wanna use express's ethernet port as LAN port. I understand this can be done in wds mode, but my extreme (n) does not allow anywhere to set up a wds under the airport utility.
do i need to buy a new express or a new extreme? If i buy a new extreme can i connect the new extreme to old extreme base station without a wire and then use the LAN ports on the new extreme to connect to a computer or tv using rj45.
thanks

but my extreme (n) does not allow anywhere to set up a wds under the airport utility.
Suggest that you download and install the more functional and useful AirPort Utility 5.6 for Mac OS X Lion , which can be used to administer both the older "g" and newer "n" devices.
Open AirPort Utility 5.6
Select the AirPort that you want to administer
Click Manual Setup
Click the Wireless tab below the icons
Hold down the option key on your Mac while you click on the Wireless Mode selection box and the WDS setting will appear so that you can make further adjustments as needed.

How can i connect apple hd cinema display 30-inch DVI to my new notebook with HDMI port

I have ask this question in the local shop but they could not answer me - how can i connect apple hd cinema display 30-inch DVI to my new notebook with HDMI port

I wasn't sure how the whole thing would have work but it seems thunderbolt also acts like mini display port. Thats sweet. I can now haply continue using my 30 inch apple display.
Thanks.

Can't Connect to SMP on port 8080

Similar Messages

Maybe you are looking for