Cannot configure and connect to Airport Express Base Station Model A1264 with Windows 7 (x64)

I am not able to connect Airport Express Base Station Model A1264 with Windows 7 (x64). I did a factory reset, uninstalled and reinstalled the AirPort Utility for Windows v. 5.6.1.
My objective is to extend a non-Apple WiFi network with Airport Express Base Station Model A1264 and use it for direct ethernet and/ or wireless connection. Any guidance as to how I can get set up here?

This is very common, we run a mix of mac and various pc brand desktops and laptops, what I have found is that using the windows wireless client rather than manufacturers on some laptops helps, getting the latest wireless drivers from the manufacturer has helped, make sure all your windows updates XP and Vista are current.
If all the above is covered try the different WEP WPA WPA2 variants or even without for test purposes. I have most success with WPA2.
Finally I am assuming your running the latest firmware on the express unit, whilst this hasn't attributed to better connectivity for us I did it regardless.
Message was edited by: Fence Rider

Similar Messages

User guide airport express base station model A1264

I want to add a Airport express into my exsisting system but lost user guide

The link below should contain a PDF copy of the required manual.
http://support.apple.com/manuals/#Airport%20express

Setup airport express base station model A1088

Ik heb een oudere airport express base station model A1088 die ik wil configuren en gebruiken met een imax met maverics erop. Het airport configuratie programma geeft echter aan dat deze versie van het configuratie programme dit basisstation niet meer ondersteund. Hoe is dit eventueel op te lossen?
Groet,
Martin

To configure an original A1088 or A1084 AirPort Express requires an older version of AirPort Utility and an older version of OS X.

How do I connect the airport express base station to the DSL modem? Can it be done wirelessly?

Can the airport express base station be wirelessly connected to the DCL modem?

Alan1111 wrote:
Can the airport express base station be wirelessly connected to the DCL modem?
Alan,
Please provide more information. (Make/model of the modem and airport express, Mac OS version, etc.)
Most likely your modem is the source of your internet connect and you sound like you are trying to extend your network through the airport express (which is a router).
I don't know what a "DCL modem" is. Perhaps you meant "DSL".
Most internet modems are either a "Cable Modem" or a "DSL Modem".
Time Warner (TMC) and Comcast typically provide cable modems, which use a coaxial (round) cable.
"DSL Modems" are used with AT&T and they are connected to your telephone wires.
Both of these types of modems usually includes a router built-in, some include a wireless router, too.
Either way, I don't know of any way to connect an Airport base station to a router wirelessly.
That would be called a "bridge" in networking terms and while it may be possible, it is not common.
Most routers use a direct ethernet cable connection, because the data flows much faster than wirelessly.
Normally, one connects to their airport base station with an ethernet cable from the primary home/office computer.
It can be accessed wirelessly, but only if you enable that option in the Airport utility (not the default).
Again, connecting or bridging one router to another router is not a common method.

Airport Express Base Station and HP Laserjet 1020 printer connected

Dear all,
I have a Laptop (PC) Sony Vaio PCG-Z1XSP and an Airport Express Base Station which work perfectly together (internet access and I-tunes). I recently bought a printer HP Laserjet 1020 and connected it to the Airport Express USB soket. I managed to make it work and print a couple of times, but as soon as I turn off the printer or the computer or Airport Express, the next time I want to print, it doesn't work anymore.
The Airport Admin Utility recognises the printer (I can see it listed). I have updated the Airport Express software to the Firmware version 6.3 as well as downloaded the latest driver available on HP's website for my printer. I've also substituted the USB cable. Can anybody help me here? Thank you very much and best regards.

Hallo everybody,
Thanks for all the answers. I have contacted HP's chat online and gone through the problem with 3 different technicians. I've tried a lot myself too. The issue was partially solved by restarting the printer spooler, i.e. stop, then start and then restart it.
However after I was so happy that the printer worked, I turn off everything. When I turn on again, it was not working anymore. Then I tried to see by exclusion what the problem is, I had to restart the Hardwar I don't know how many times.
Conclusion:
1. The USB cable must be plugged into the airport express before turning on anything.
2. Turn on the printer first.
3. Turn on the airport express and the computer.
4. If you try to print it doesn't work, even if you reset the airport express through the airport express utility software. The printer is recognized and appears in it though.
5. Disconnect the USB cable from the airport express and connect it to the PC directly.
6. Print a document.
7. Disconnect the cable and reconnect it to the airport express.
8. Now you should be able to print wireless. You may need to reset the airport expresst with the utility softwar, but I managed to print without having to do it.
9. The pörinter works even if you turn off and on again the computer, or you suspend the windows session and restart it, or if you put it in standby and restart it.
10. The printer works even if you turn off the airport express and the computer, or the airport express alone and restart them/it.
11. The printer doens't work anymore if you turn it off and onn again. In such a case you have to plug in/out as discribeb above.
Solution: Leave the printer always on, or make the plug in/out every morning when you start the computer and print one page direclty before being able to print wireless.
Does anybody have a solution to this problem? I mean it prints, but it is annoying to plug in/out every day, no?
HP's technician says that it is not a recommanded solution the HP Laserjet 1020 with the airport express, since the printer works on a host based server basis... I mean it is easy to say that, but one expects to buy a printer that works always and not to have to plug in/out everyday, restart spooler and so on.
Can anybody comment or suggest anything I can do to avoid this? Thank you and I hope this helps others too.

Connecting to multiple Airport Express base stations for internet and TV?

I want to be able to use wireless internet and stream music to my stereo at the same time, but I only have a single ethernet connection behind my stereo and it's connected to the Pay TV. My options seem to be an ethernet splitter (maybe - any ideas?), getting a new ethernet connection installed behind the stereo so I can insert this into the same Airport Express base station I use for my music, or buying a second Airport Express base station and connecting it to one of the other internet connections in the room, then connecting to both Airport Express base stations at the same time.
Is this possible? Are there other alternatives?
Many thanks

Nate, Welcome to the discussion area!
Once you have a network, you can connect multiple AirPort Express (AX) to that network (wirelessly or via Ethernet). When your computer joins that network it can access all the AX.
You could take your current internet connection and run it into an inexpensive router with multiple Ethernet ports (not the AX). If this is a wireless router then your AXs could be located elsewhere and connect as wireless clients to that network. Once you computer joined that network it could stream music to the AXs.

Hey, I have a AirPort Express Base Station ( 2nd Generation ), and I wanted to ask that if I join my network at home with the Express Station, will it still run the 2.5 GHz and the 5.0 GHz?

Okay, well I have just bought a AirPort Express Base Station ( 2nd Generation ) and I'm new to it, but I wanted to ask that if it join's a network you have setup at home, will it still run with the 2.4 GHz and the 5.0 GHz.

The AirPort Express will "extend" both the 2.4 GHz and 5 GHz networks and provide more wireless signal coverage when it is connected to another Apple AirPort router and configured correctly.
The AirPort Express cannot provide more wireless coverage though, if you are trying to connect it to another 3rd party wireless router using wireless only.
It should be possible to set up the Express to provide more signal coverage if you connect it back to the main router using a wired Ethernet connection or using Ethernet powerline adapters.

Airport Express Base Station and AirTunes

I was given an Airport Express Base Station and I purchased
a PCMCIA wireless card (802.11g). After installation of both items I then upgraded the iTunes software to v4.9. I want to transmit music from my laptop to the Airport Express Base Station. I understand I require the AirTunes software butI cannot find a download site for that application. The CD that came with the Base Station does not have Airtunes (obviously an older version of the application software). Is AirTunes available as a download?
Thanks

Airtunes support is built in to iTunes version 4.9 - there is no other software you need to download or install. If your PC has been successfully set up to connect to the Airport Express wireless network, a drop down box will appear in the lower right corner of the iTunes application window where you can select the place your iTunes should be playing (ie internal speakers, or the Airport Express).
You did not mention either (a) configuring your Airport Express or (b) setting up your PC to connect to the Airport Express wireless network. To do this:
(a) read the configuration manual for the Airport Express. Then download the Airport 4.2 update for Windows (from Apple's web site) - it provides the latest Windows versions of the Airport Express configuration software.
(b) to get your PC to connect to the Airport Express wireless network, see the links to "accessing an airport network" provided at:
http://www.efelix.co.uk/tech/windowsxp.html

I have two airport express base stations that I want to configure on two separate sets of speakers in two separate rooms. How do I do this? Airport Utility only seems to scan one express at a time.

I am currently running a PowerPC G5 imac and have a wired broadband modem via ethernet with airport wireless network turned on, on the G5. I have the computer in the bedroom and have an airport express wired into a mixer that connects to my stereo. I have recently bought another airport express base station to connect to a pair of active monitors in the kitchen. When I try to scan these on Airport Utility version 5.42 I am only managing to scan one base unit at a time. I have plugged them in separately and reset them, they both have firmware updates, however the utility will only read one at once. I have read that you can link base stations to the same WDS. I would like to know how to go about doing this if it will only scan one airport express at a time. I have looked it up on the net and not found anything that is a simple fix. Can anyone help? In Apple Support it says that multiple Base Stations can be used. I would like to get both Apple Airport Express units to be able play airtunes separately or at the same time depending where I am in my flat. I do not need different music in each room. I would like to stream music from the computer to multiple rooms in the flat without having to continually unplug and configure the Base Stations. Has anyone come across such a challenge? Any help would be welcome.

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Can't read airport express base station configuration wirelessly

The setup:
2TB time capsule that takes the ethernet feed from the cable modem for internet access.
Airport express 802.11g plugged into speakers for Airtunes. No ethernet connection, just a wireless network.
The problem:
I can only read the airport express base station configuration when the mac is plugged into the time capsule by ethernet cable. This does not happen with the other mac I have on the network. It can connect to both the time capsule and the airport express without any problems. So unless I'm plugged in, iTunes and airtunes doesn't connect to the base station, and neither can Airfoil 3.5 or Airport Utility. Airport Utility does see the airport express. It just doesn't read the configuration wirelessly.
I think this had something to do with elgato eyetv not liking airfoil, but I can't say for sure.
Any thoughts?

When I switch it on all three lights flash, but then after a while the middle one stays on and nothing happens.
You posted in the AirPort Express area, but it sounds like you have an AirPort Extreme Base Station (AEBS)--correct?
If so, let's start by performing a complete power recycling of your network components to make sure that the BT Voyager router "recognizes" the AEBS.
Modem/Router Power Recycling - Quick
- Power-off the BT Voyager modem, AEBS, & computer(s); Wait at least 5 minutes.
- Power-on the BT Voyager modem; Wait at least 5 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
- Power-off the BT Voyager modem, AEBS, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
- Power-on the BT Voyager modem; Wait at least 30 minutes.
- Power-on the AEBS; Wait at least 5 minutes.
- Power-on the computer(s)

I have got a Airport Extreme Basestation and an 3 x Airport Express Base station.

Hi
I have a netgear modem. Would like help with how to create one network with strong wireless signal all around the house and the gym outside. I basically know how I will setup the Airport Extreme and One Express ( for streaming music from Itunes ). How to use the other two Expresses to extend the wireless side of the network to have a strong signal all around the residental area.
Please help

Not knowing your exact building floorplan, I would start with the following basic setup of your AirPorts:
Connect the 802.11n AirPort Extreme Base Station (AEBSn) to the Netgear router by Ethernet.
Reconfigure the AEBSn as a bridge.
Configure the AEBSn for the option "Allow this network to be extended" enabled.
Configure each of the 802.11n AirPort Express Base Stations (AXn) with the option "Wireless Mode = Extend a wireless network" enabled.
Both AXns will be connected back to the AEBSn by wireless.

I want to re-use my old airport express base station but airport utility doesn't recognise it anymore (it dates from 2005) i would like to use it to connect to my speakers only

I have an old airport express base station from 2005
I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
Can i update the firmware? has it become useless because too old or what can i do?
I work on macbook pro with macOSX 10.9.4
Can someone give me some tips please
thanks
J

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

Steady green light on A1084. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it. Is there a fix?

Steady green light on A1084. Mac OS X 10.7.5. IMac. Verizon DSL Actiontec GT704-WGB modem. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it and send a signal to airport express to play airtunes through my stereo amplifier. Is there a fix?

I plugged a model A1034 Airport Extreme Base Station into the Verizon DSL Actiontec GT704-WGB modem with an ethernet cable and now the AirPlay icon appears in the Itunes window immediately to the right of the volume control and I can select it and play Airtunes wirelessly through the A1038 Airport Express Base Station in another room connected to a stereo amplifier by a Monster mini-to-RCA left/right audio cable running from the output jack on the A1034 Airport Express Base Station into the CD jacks on the amp. The problem is that I have to select the Apple Network Airport Express Base Station as my network in order to select the Airport Express Base Station when I click the AirPlay icon, which means I have no Internet signal to the Imac. If I select the Airport Extreme Base Station or the Verzion modem as my network, then I have an Internet signal to the Imac, but the Airport Express Base Station is grayed out when I click on the AirPlay icon, so I cannot select the Airport Express Base Station and send tunes to the Airport Express. It would be nice to play Airtunes while simultaneously accessing the Internet. I don't understand your question about what program I am using for which I require AirPlay. I am not learned about computers in general, and even less so about Macs than PCs. I thought the program I was running was Itunes, and there was no separate program to run to use AirPlay for the purpose of sending a signal from the Itunes on the Imac to the A1084 Airport Express base station in a another room, and then out as described above to the stereo amplifier to listen to Itunes music remotely in the other room, without any kind of cable, wire, etc., connecting the Imac to the stereo amplifier. I would guess that the most common use for the A1084 is to play Itunes through a stereo in another room without the need to run wires from the computer to the stereo. I realize it would be easy simply to run a very long mini-to-RCA left/right audio cable across the floor connecting the Imac to the amp without the need to use AirTunes, Airplay or any kind of AirPort, but it would be both unsightly and a tripping hazard.

Why have all 3 airport express base stations stopped working, BT have checked and improved line still not working?

Why have all 3 airport express base stations stopped working, other users are on ipads and BT have checked and improved line but I still have an intermittent/no connection?

You must tell us the whole setup.. what is the main router?? How are the express connected to each other?
On ipad it works ok?? But you are on a computer?? MBP early 2011 running Lion?? That doesn't work.. even if you are right next to the main router??
Plugged in by ethernet does it work??
Have you installed a wireless diagnostic program.. ?? Actually Lion has one installed but hidden I believe.
Later version bought it to the surface.
About Wireless Diagnostics
If you do run Lion please install the 5.6 airport utility as it will give you loads more info on how the units are connected.. and link speeds for extend wireless.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

HELP: Airport Express Base Station over PPPoE and Static IP

Hi there,
I recently purchased a Airport Express Base Station after doing some preliminary research as to wether it would work with my Windows XP Machine.
After finally acquiring it today, I have been trying to set it up with ZERO luck so far.
I open the neat package and plug in the wires as mentioned in the manual and get the AE on. I install the AE software from the CD, my computer recognises the wireless network, all going well.
I setup the airport express using the setup assistant for windows and then open the Airport admin utility. Now here is where I come across the first stumbling block.
My ISP provides each end user with LAN connectivity(primitive), what they do is install a router in every apartment complex and then provide internet through LAN connectivity to every apartment. In doing this they assign each users network adapter a static IP alongwith a lock-in for the MAC address for the specific adapter.
So if you have to change network adapters you have to call them, they release the lock temporarily and you can connect using another adapter without issue.
Another thing they also provide is a Username/password for every apartment user to be able to access the internet once connected. I am not a expert but I am guessing that is what they call PPPoE.
Now I have been trying to setup my Airport Express using the admin utlity but I discovered that it is not possible to specify a Static IP and use PPPoE both together.
How do i get this to work now? .. In addition I have a HP 1010 USB laserjet which I would like to share using my AE, I am guessing I can just create a TCPIP Port for this with the IP of the AE and it should work.
Please help, really require to get this working ASAP with 3 windows machines (2 laptops and 1 desktop)
Many thanks

The Airport Admin utility internet TAB reads as follows
Connect Using Ethernet
Configure TCP/IP using Ethernet
Configure Manually
IP Address: 192.168.3.170
Subnet Mask: 255.255.255.0
Router Address: 192.168.1.1
DNS Servers: blank
blank
Domain Name: Blank
WAN Ethernet port: Automatic
The Network Tab reads as follows
Distribute IP Addresses [CHECKED]
Share a Single IP Address (using DHCP & NAT) [CHECKED]
Use 10.0.1.1/24 addressing [used option]
No other options checked on this tab.
The IPCONFIG reveals the following
===========================================================
C:\Documents and Settings\TAPAN>ipconfig
Windows IP Configuration
Ethernet adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 10.0.1.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.0.1.1
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.3.170
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
==========================================================
Ethernet shows up here because I am using the internet on my computer directly right now.
But the AE is connected and printer and Airtunes is working fine. It still flashes Amber though.
Any other details you require to further analyse the problem? .. I have tried various combinations of basic IP settings. Resets to the AE, restarts to the Computer already. But I am willing to follow any additional instructions you might have for me and provide you any other information you might require.
Many thanks, You should realise that your continuing support is very encouraging and means a lot to me.

Cannot configure and connect to Airport Express Base Station Model A1264 with Windows 7 (x64)

Similar Messages

Maybe you are looking for