Cannot connect to the network after fresh install

Hello everyone. So I followed the Beginner's Guide to the letter during setup. Everything was all peachy, including the network (since I used the FTP/HTTP ISO to install Arch Linux). My NIC got assigned an IP address from my router via DHCP. However, after the installation process was finished and I booted to the actual system, it seems that I cannot get an IP address from the router at all. When I try to run dhcpcd eth0, it always times out.
There have been a couple of posts about this in the past month, and I tried all the solutions that were mentioned there. None of them worked. I double-checked my /etc/rc.conf, /etc/dhcpcd.conf, and /etc/hosts files. They are correct as far as I can tell. No typos or anything like that. Heck, I even tried increasing dhcpcd's timeout to a full minute. Still no dice. This post seems to suggest that dhcpcd has a regression bug.
So... does anyone have any suggestions as to the next course of action I should take? I would appreciate any help.
EDIT: For what it's worth, I'm trying to install Arch Linux on a Dell Inspiron 9300 laptop. I'm not too sure about the exact model for the built-in NIC, but I suspect it is one of those built-in NICs from Intel.
Last edited by Kirby54925 (2009-08-08 12:50:43)

No, I have not even installed any DE/WMs yet (how can I if the network doesn't even work?). Hell, X.org is not even set up yet. Keep in mind that my problem takes place IMMEDIATELY after I finished running the FTP/HTTP installer (so in the Beginner's Guide, I would be right at the beginning of Part II, which is configuring the new Arch system). The kernel version is 2.6.30.4. The ethernet card is a Broadcom 440x 10/100, I believe. I don't believe a driver is needed for that card due to kernel support (this card does indeed work with Ubuntu as well as the Arch livecd itself). And yes, I did read the relevant wikis, including the Beginner's Guide and the Network wiki.
So to summarize, the network does indeed work while I'm going through the initial stages of installation with the Arch livecd. Since I am using the FTP/HTTP installation CD, I have to download all of the packages I need for installing the base system. It is after that point when the base system is fully installed, allowing me to boot off the hard drive, when the network fails to get an IP address from the router.
Anyhow, thank you very much for the welcome and for your response! Hopefully we will be able to get to the bottom of this problem.
EDIT: This person and this other person seem to have the same problem I do. They, unfortunately, did not come up with a sufficient resolution to the problem. I hope this helps in making the issue clear.
Last edited by Kirby54925 (2009-08-08 18:29:39)

Similar Messages

Configuration Manager Cannot Connect to the Site After SP1 Install

I've been working on this all morning and can't seem to get anywhere on it. I've updated SCCM 2012 to SCCM 2012 SP1 and SQL Server 2008 to SQL Server 2008 SP3 CU4 and I can no longer connect to the site database. I've checked though the SQL settings as well
as SPN settings and everything checks out. I've looked at the SMSAdminUI log and to me it looks like SCCM can't even see the site database.
[4, PID:4948][01/28/2013 09:49:03] :System.Management.ManagementException\r\nProvider load failure \r\n at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
at System.Management.ManagementObjectCollection.ManagementObjectEnumerator.MoveNext()
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlQueryResultsObject.<GetEnumerator>d__0.MoveNext()\r\nManagementException details:
instance of __ExtendedStatus
Operation = "ExecQuery";
ParameterInfo = "SELECT * FROM SMS_Site WHERE SiteCode = 'ISD'";
ProviderName = "WinMgmt";
\r\n
[4, PID:4948][01/28/2013 09:49:03] :Transport error; failed to connect, message: 'The SMS Provider reported an error.'\r\nMicrosoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlQueryException\r\nThe SMS Provider reported an error.\r\n
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlQueryResultsObject.<GetEnumerator>d__0.MoveNext()
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.Connect(String configMgrServerPath)
at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\nConfigMgr Error Object:
instance of __ExtendedStatus
Operation = "ExecQuery";
ParameterInfo = "SELECT * FROM SMS_Site WHERE SiteCode = 'ISD'";
ProviderName = "WinMgmt";
Error Code:
ProviderLoadFailure
\r\nSystem.Management.ManagementException\r\nProvider load failure \r\n at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
at System.Management.ManagementObjectCollection.ManagementObjectEnumerator.MoveNext()
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlQueryResultsObject.<GetEnumerator>d__0.MoveNext()\r\nManagementException details:
instance of __ExtendedStatus
Operation = "ExecQuery";
ParameterInfo = "SELECT * FROM SMS_Site WHERE SiteCode = 'ISD'";
ProviderName = "WinMgmt";
\r\n
[4, PID:4948][01/28/2013 09:49:03] :System.Management.ManagementException\r\nNot found \r\n at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
at System.Management.ManagementObject.InvokeMethod(String methodName, ManagementBaseObject inParameters, InvokeMethodOptions options)
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.ExecuteMethod(String methodClass, String methodName, Dictionary`2 methodParameters, Boolean traceParameters)\r\nManagementException details:
instance of __ExtendedStatus
Operation = "ExecMethod";
ParameterInfo = "SMS_ObjectLock";
ProviderName = "WinMgmt";
\r\n
I tried to re-compile smsprov.mof and I get the following error (Yes, I was logged on as Admin with elevated rights):
Microsoft (R) MOF Compiler Version 6.2.9200.16398
Copyright (c) Microsoft Corp. 1997-2006. All rights reserved.
Parsing MOF file: E:\SCCM\bin\X64\smsprov.mof
MOF file has been successfully parsed
Storing data in the repository...
An error occurred while processing item 3 defined on lines 29 - 37 in file E:\SC
CM\bin\X64\smsprov.mof:
Error Number: 0x80041026, Facility: WMI
Description: Class has instances
Compiler returned error 0x80041026
Is it possible there is something wrong with my WMI? I'm not really sure where to go from here and I'm dead in the water. Any help would be greatly appreciated!

Since no one has answer this post, I recommend opening a support case with CSS as they can work with you to solve this problem.
Garth Jones | My blogs: Enhansoft and
Old Blog site | Twitter:
@GarthMJ

I cannot connect to the Internet after installation of Windows Vista Ultimate edition.

I cannot connect to the Internet after installation of Windows Vista Ultimate edition. For some odd reason, it seems my ethernet has not yet been installed to my operating system and I do not know how to do that even with the internet, I have the LAN cable hooked up to my computer but I do not know exactly what to do about it. Is there some sort of driver I need to install, or what? How do I do that without the internet?
This operating system is on a separate partition to my other operating system that is connected to internet already (Windows Vista Premium) that I do not wish to use anymore because of it's corruption. I tell you this because you may know a way of finding the driver files on my previous operating system that I may be able to transfer to the other.

In order to avoid board clutter, we ask that you post your topic on one board only.
Please look ---> HERE for replies to your topic. Thank you.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer that solved your issue as the accepted solution.

I cannot connect to the internet after switching providers. I've changed the email address associated with the new account but am sure there is something else I need to change. Can anyone help me?

I cannot connect to the internet after switching providers. I've changed the email address associated with the new account but am sure there is something else I need to change.   I have also changed the apple information as well including user name and password. Can anyone help me? (This is an ipad question).

Apple ID: Changing your Apple ID
http://support.apple.com/kb/ht5621
Using your Apple ID for Apple services
http://support.apple.com/kb/HT4895
Apple ID: What to do after you change your Apple ID
http://support.apple.com/kb/HT5796?viewlocale=en_US&locale=en_US
iTunes Store: Associating a device or computer to your Apple ID
http://support.apple.com/kb/ht4627
iOS: Changing the signed-in iTunes Store Apple ID Account
http://support.apple.com/kb/ht1311
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at
http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are drooping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
iPad: Issues connecting to Wi-Fi networks
http://support.apple.com/kb/ts3304
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.hmL
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Signal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

TS1398 I did everything you are recommend to do and still cannot connect to the network. "Unable to join network" shows up even that is a university network working for other users - students and staff. I am very unhappy with my new iphone 5 :(

I did everything recommended on apple store support site and still cannot connect to the network with my new iphone 5 but my co-workers and students (I work for the university) can keep connectivity all the time. I am very unhappy with my new phone

Be patient, Apple is coming out with a update soon, its been reported that they have sent the update to the carriers to test, which means it will be soon. And is suppose to address this issue.

Cannot connect to the net after installation

Hi All:
I tried to install and work with Archlinux today but was not successful at all.
I downloaded the ISO image of archlinux and burnt it to a CD (Archlinux-i686-2007.05-Duke). I tried to install the distro to my Compaq presario 700AP laptop (AMD Duron/128 MB RAM) Installation went smoothly and then the problems began. I coud not get networking to work. Here are the contents of the /etc/rc.conf file (networking section only given here):
<--- contents of /etc/rc.conf ------------->
lo="lo 127.0.0.1"
eth0="eth0 192.168.1.10 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(lo eth0)
gateway="default gw 192.168.1.1"
ROUTES=(gateway) ......................."I removed the ! sign to activate the gateway"
<-------/contents ------>
<--------- contents of /etc/resolv.conf ------------>
and in the /etc/resolv.conf, I have
nameserver 208.67.222.222
nameserver 208.67.220.220
search opendns.com
I typed opendns.com since I have these dns addresses from opendns.
<-------------
When I ping my nameserver (208.67.222.222), it puts out several lines of messages like:
64 bytes from 208.67.222.222: icmp_seq=55 ttl=252 time=284 ms
Likewise, when I ping default gateway, I get several lines of messages like:
64 bytes from 192.168.1.1: icmp_seq=1 ttl=128 time=1.62 ms
Yet I cannot ping google (http://www.google.com), and the error message is: "unknown host", nor can I use pacman to update packages from online repositories.
What am I doing wrong? I have followed the networking guidelines and installation guidelines from the websites.
Do I reinstall archlinux? I am lost.
Best wishes,
/Arin

Thanks for the advice, but I still am not successful and I cannot figure out why.
Dear All:
Thanks for all your responses, but I still cannot connect to the Internet and this is a strange problem.
I use a broadband connection, provided by India's BSNL broadband service, using an external modem (Huawei Corporation; SmartAx MT882). The internet service has provided me the following information:
IP Address: 192.168.1.10
Subnet mask: 255.255.255.0
Default gateway: 192.168.1.1
DNS servers: 218.248.255.145
DNS server(2): 61.1.96.71
In addition, I use opendns and the dns server names are:
208.67.222.222
208.67.220.220
Here are the contents of my /etc/rc.conf (networking section):
HOSTNAME="maurine"
Io="Io 127.0.0.1"
eth0="eth0 192.168.1.10 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(Io eth0)
gateway="default gw 192.168.1.1"
ROUTES=(gateway)
Contents of my /etc/resolv.conf
search maurine.com
nameserver 218.248.255.145
nameserver 61.1.96.71
nameserver 208.67.222.222
nameserver 208.67.220.220
If I try using pppoe -I eth0, it waits for some time and then returns a message "timeout waiting for PADO packets"
If I "try /etc/rc.d/adsl start", it returns [FAIL] after some time.
This has never been a problem with my ubuntu or windows installations before, I could easily connect to the web.
What should I do to make sure I can connect to the Internet?
When I ping 192.168.1.1, it takes me to my modem page and from there, when I run the diagnostics, it returns everything ok.
Where may be the problem and what do I need to do to resolve this problem?
Thanks in advance,
Arin Basu

"Configuration Manager cannot connect to the site" after site update from SP1 to R2

Our dev SCCM environment only has a single primary site with a remote SQL database. Initially, the dev primary site had SP1 Beta (5.00.7782.1000) installed but as everyone is aware there is no upgrade path available to SP1 or R2 from Beta; so, we uninstalled
the site and removed the database, re-installed SP1 non-Beta (5.00.7804.1000), then proceeded to update all devices with the latest client agent. Afterwards, we attempted to upgrade the site from SP1 non-Beta (5.00.7804.1000) to R2 (5.00.7958.1000).
All seemed well until we attempt to open the Configuration Manager console and we get the following error message:
Configuration Manager cannot connect to the site (Site Name)
The Configuration Manager Administrator console could not connect to the Configuration Manager site database. Verify the version of the console is compatible with the version of the site server you are connecting to and then try to connect again.
So we tried reinstalling the console directly from here...
"C:\Program Files\Microsoft Configuration Manager\tools\ConsoleSetup\AdminConsole.msi"
still the same error message persisted, so we tried installing it from here...
"C:\Program Files\Microsoft Configuration Manager\tools\ConsoleSetup\ConsoleSetup.exe"
still the same error message persisted, so then we tried installing it directly from the R2 (5.00.7958.1000) installation media, and afterwards the same error message persisted....
All along, we were checking the AdminConsole log from here:
"C:\Program Files (x86)\Microsoft Configuration Manager\AdminConsole\AdminUILog\SmsAdminUI.log"
Here are the contents:
[4, PID:4836][04/22/2014 15:21:10] :Property: 'Features'\r\nSystem.Management.ManagementException\r\nNot found \r\n at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
at System.Management.PropertyData.RefreshPropertyInfo()
at System.Management.PropertyDataCollection.get_Item(String propertyName)
at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlResultObjectBase.get_Item(String name)\r\nManagementException details:
[4, PID:4836][04/22/2014 15:21:10] :ReadExtraProperties: Failed to initialize extra properties
[4, PID:4836][04/22/2014 15:21:11] :Transport error; failed to connect, message: 'The Configuration Manager Administrator console could not connect to the Configuration Manager site database. Verify the version of the console is compatible with the version
of the site server you are connecting to and then try to connect again.'\r\nMicrosoft.ConfigurationManagement.ManagementProvider.SmsConnectionWithDetailException\r\nThe Configuration Manager Administrator console could not connect to the Configuration Manager
site database. Verify the version of the console is compatible with the version of the site server you are connecting to and then try to connect again.\r\n at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.ValidateConnectionParameters(ConnectionManagerBase
connection)
at Microsoft.ConfigurationManagement.AdminConsole.SmsSiteConnectionNode.GetConnectionManagerInstance(String connectionManagerInstance)\r\nNo details are available for this error.\r\n
Once again, we validated we could connect to the SQL database from this box, and that the console was at the same version as the site. Any help or guidance with getting our access to the console restored after the SP1 to R2 upgrade would be greatly
appreciated.

From the Primary Site Server, I tried uninstalling the Admin Console and re-installing using:
consolesetup.exe /q TargetDir="%ProgramFiles%\Microsoft Configuration Manager" EnableSQM=0 DefaultSiteServerName=<SiteServerName>
Of course replacing <SiteServerName> with the FQDN of my Primary Site Server. Console installed successfully however the same error message persists.
Also tried installing the console on a clean Windows Server 2008 R2 installation. I tried it from the R2 (5.00.7958.1000) installation media, from the "C:\Program Files\Microsoft Configuration Manager\tools\ConsoleSetup\" both without any luck, the
same error message persists. I verified I could ping the FQDN of the site server also, and that the firewall between the two permits communication over the ports listed here: http://technet.microsoft.com/en-us/library/hh427328.aspx
Any help would be greatly appreciated.

TS1398 i have a good signal on my ipad wi fi but cannot connect to the network

I have a good wi fi connection on my ipad but cannot connect to the network

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Domain users cannot connect to the network folders when logged in via rds remote apps

Hi,
recently I setup an RDS farm for remote apps on server 2012 r2.
all users can connect to the apps published. no problems there.
but when users connect via rds they cannot connect to the networkfolders and cannot store the resultance of there work (docx and xlsx files)
all users are normally connected to the networkfolders using a small login batch file handing down the unc path needed. when I log in as domain admin, also using a login batch, connections are setup correctly. It seems to me to be an security issue on the
rds session host.
how to alter this?
greetz, Fons
Fons system and network engineer Balie Amsterdam

Hi,
Thank you for posting in Windows Server Forum.
We use WMI to communicate with the RDSH server. Various issues can cause WMI to deny access or return error codes. Here's a few things you can try:
1. Check if the "TS Web Access Computers" security group on the RDSH server has incorrect permissions in DCOM and/or WMI:
For checking DCOM security settings:
1. Start the Component Services MMC snapin
2. Navigate to Component Services -> Computers -> My Computer
3. Right-click on My Computer and select properties
4. Go to the COM Security tab
5. Under Access Permissions, click the Edit Limits button
6. Ensure that TS Web Access Computers is in the list, with all of the permissions set to “allow”.
7. Under Launch and Activation Permissions, click the Edit Limits button
8. Ensure that TS Web Access Computers is in the list, with all of the permissions set to “allow”.
For checking WMI security settings:
1. Start the WMI Control MMC snapin
2. Right-click the WMI Control node and select properties
3. Go to the Security tab
4. Navigate to Root->CIMV2->TerminalServices
5. With TerminalServices selected, click the Security button
6. Ensure that TS Web Access Computers is in the list with Execute Methods, Enable Account, and Remote Enable set to "allow"
2. Verify the RD Session Host server's firewall allows WMI calls.
3. Verify that the RD Connection Broker hasn't lost its trust relationship with the domain.
4. See if non-RDS related WMI calls can be successfully made to the RDSH server. This can help differentiate between a general WMI issue and an issue calling the RDS WMI provider.
(Quoted from following thread.)
RemoteApp Source not working from RDWeb
http://social.technet.microsoft.com/Forums/windowsserver/en-US/173d4546-e12f-47c1-ac66-8b4f69826892/remoteapp-source-not-working-from-rdweb?forum=winserverTS
Hope it helps!
Thanks.
Dharmesh Solanki

Cannot connect to college network after installing Vista business on Satellite A215

I have a Satellite A215-S4757, which i brought with me to college, I was told that the college's server has a problem running on vista home, which is what I had, currently the wireless is down, so after installing business and connecting the ethernet cable my notebook does not pickup any of several networks available, wireless or otherwsie

What to say you can also access the network using Vista.
But please note that the Vista OS supports additional network access security settings which must be either disabled or reset.
This How to website released by Microsoft should help you to configure the network settings with Vista:
http://windowshelp.microsoft.com/Windows/en-US/networking.mspx
Here several hints:
You should try to Open Network Diagnostics by right-clicking the network icon in the notification area, and then clicking Diagnose and repair.
The Vista supports additional firewall options. Please disable it while trying to connect to the server.

Cannot connect to sql server after re installing IIS 6?

I re installed IIS 6, after the restart i couldn't connect to sql server engine nor seeing it when using browse for me, i was trying to install team foundation server, at first it could see that i have an sql server running after re installing IIS it can't
see it also. I'm using windows server 2003 SP2. Also i cannot remotely access it after the re installation

Just type the IP or name of the server (localhost) and try to connect.. SSRS 2005 requires IIS but how does it relate to SQL Server connection?
What error are you getting? Make sure that SQL Server is running up.
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Consulting:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance
SQL Server Integration Services:
Business Intelligence

Cannot connect to 4G network after update to OS 10.3.1

Have a Q10 through Sprint and after updating to OS 10.3.1 from the Blackberry site, phone will now only connect to 3G network despite availablity of 4G network. Phone used to connect to 4G network with OS 10.2,

I do have same problem, i'm unable to connect to even 3G network and it connect to 2G network only when there is full network
My page on: App World
Check out my Apps 1). QFileExplorer 2). My ABCD
System Explorer APPID: 35601892

Cannot connect to iTunes Store after iOS installed on iPad wifi 3rd generation

My iPad 3rd generation was just updated to iOS yesterday without any problems. I can use the Internet and the wifi network just fine.
But, I am unable to access the iTunes store no matter what I have done. I reset the router / modem. I am really ****** that this has happened. At home there are no problems. There is nothing that I have done that caused this as far as I can tell. I took my Apple ID off and then put it back on the iTunes & App Store a number of times. Nothing works. It keeps asking me to Sign In and then it says I can't

Hey tpolevoy,
Thanks for the question. After reviewing your post, it sounds like you can't connect to iTunes store on the iOS device. A frustrating situation for sure. I would recommend that you read this article, it may be able to help you resolve or isolate the issue.
Can't connect to the iTunes Store
Troubleshoot issues on an iPhone, iPad, or iPod touch
If you haven't been able to connect to the iTunes Store:
Make sure your date, time, and time zone are correct in Settings > General > Date & Time.
Note: Time Zone may list another city in your time zone.
Make sure that your iOS software is up to date by tapping Settings > General > Software Update (iOS 5 or later) or connecting your iOS device to iTunes and clicking Check for Update on your device's Summary page.
Check and verify that you're in range of a Wi-Fi router or base station. If you're on a device with cellular service, make sure that cellular data is turned on from Settings > General > Cellular.
Note: If connected to cellular data, larger items may not download. You may need to connect to Wi-Fi to download apps, videos, and podcasts.
Make sure that you have an active Internet connection. You can check the user guide for your device for help with connecting to the Internet.
Make sure that other devices (portable computers, for example) are able to connect to the Wi-Fi network and access the Internet.
Try resetting (turning off and then on again) your Wi-Fi router.
If the issue persists, try troubleshooting your Wi-Fi networks and connections.
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Cannot connect to cellular network after 6.1.2 upgrade

I just upgraded my iPhone 5 to 6.1.2 this morning via an over-the-air update on my WiFi network. The upgrade appears to have been successful, however, it can no longer connect to the Verizon cellular network.
I tried restarting the device, but no luck.
I tried turning Airplane mode on and off....no luck.
I confirmed that Celluar is on in the General settings.
My wife's phone and my phone are on the same Verizon account and I had service (full bars) just prior to performing the upgrade. My wife's phone has not been upgraded and it still has full bars.
I'm at a loss as to what to do next.

I tried resetting the phone back to the factory settings, but still had the same problem. I made an appointment at the Apple Store and took it in.
I told the tech everything that I tried and he checked a couple of other things behind the counter. Ultimately, he diagnosed it as a problem with the SIM slot on the phone--he took the SIM out and it didn't give him a "missing SIM" message (or the like) which apparently the phone is supposed to do when you remove the SIM.
He replaced the phone with a new one. Fortunately, I had all my stuff backed up on iCloud so within about 20 mins, my phone was back to normal (less all my music content, which I synced when I got home.)
The tech mentioned that the troubleshooting steps I tried were sound, so if you experience the same problem give varjak paw's suggestions a try first. :-)

I need help......I just cannot connect to the internet after changing my passcode.

Hello all,
I feel extremely stupid. Today I was changing my seetings in the http://192.168.1.1 page. But when I clicked OK I lost connection and when I try and put in my new passcode it connects to the access point but the internet cannot be found. I can only imagine that i typed the passcode in incorrectly. Now i am unable to connect to http://192.168.1.1 even when I am using my wired connection as I presume I need to be connected to my wireless router. Is there any way of changing the passcode? Can I restore the factory settings? Please help....I feel as though I may have made a huge mistake .
Jon

if you connect the PC to the router directly using a cable would you be able to get online???

Cannot connect to the network after fresh install

Similar Messages

Maybe you are looking for