Cannot mount NTFS file system on USB drive
I plug in external disk via USB drive. I attempt to mount drive. I've downloaded several NTFS rpms.
I believe the issue is that I do not yet have the correct NTFS rpm. Any help?
[root@kclinux1 media]# mount -t ntfs /dev/sdc1 /media/usbdrive/
mount: unknown filesystem type 'ntfs'
[root@kclinux1 media]# cat /proc/filesystems |grep ntf
[root@kclinux1 media]# uname -a
Linux kclinux1 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:41:04 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
[root@kclinux1 media]# rpm -qa|grep ntfs
ntfsprogs-1.9.4-1.2.el4.rf
kernel-module-ntfs-2.6.18-128.1.1.el5xen-2.1.27-0.rr.10.11
kernel-module-ntfs-2.6.18-128.el5xen-2.1.27-0.rr.10.11
[root@kclinux1 media]#
try
step 1)
# Red Hat Enterprise Linux 5 / i386:
rpm -Uhv http://apt.sw.be/redhat/el5/en/i386/rpmforge/RPMS/rpmforge-release-0.3.6-1.el5.rf.i386.rpm
# Red Hat Enterprise Linux 5 / x86_64:
rpm -Uhv http://apt.sw.be/redhat/el5/en/x86_64/rpmforge/RPMS//rpmforge-release-0.3.6-1.el5.rf.x86_64.rpm
# Red Hat Enterprise Linux 4 / i386:
rpm -Uhv http://apt.sw.be/redhat/el4/en/i386/rpmforge/RPMS/rpmforge-release-0.3.6-1.el4.rf.i386.rpm
# Red Hat Enterprise Linux 4 / x86_64:
rpm -Uhv http://apt.sw.be/redhat/el4/en/x86_64/rpmforge/RPMS/rpmforge-release-0.3.6-1.el4.rf.x86_64.rpmstep 2)
apt-get updatestep 3)
> yum install ntfs-3g
> ntfs-3g /dev/sdxy /<mount directory>
rgrds
Similar Messages
-
I am trying to reinstall Windows (would not launch). I removed the partition and started over. I downloaded the support files and Windows 7 iso file to a USB drive. However, when I try to run the setup.exe program I get the message "this program cannot be run in DOS mode." I was successful before, what am I doing wrong this time?
Try a restart.
If that doesn't fix the problem, shut down the computer and then power it back up. Immediately after hearing the startup chime, hold down the shift key and continue to hold it until the gray Apple icon and a progress bar appear. The boot up is significantly slower than normal. This will reset some caches, forces a directory check, and disables all startup and login items, among other things. If the system operates normally, there may be 3rd party applications which are causing a problem. Try deleting/disabling the third party applications after a restart by using the application unistaller. For each disable/delete, you will need to restart if you don't do them all at once.
Safe Mode
Safe Mode - About
General information.
Isolating issues in Mac OS X
Troubleshooting Permission Issues
Step by Step to Fix Your Mac -
Ive just changed from windows to mac. I am now having a bit of a problem. With my old windows computer i used a 180gb usb hardrive on NTFS file system. I can read the files on my new mac but i cant put anything on there. So i now realise i have to convert the hardrive to a mac file system. But i have lots of files on there and i assume reformating will wipe all the files??? Does anyone have any suggestions of what i can do? I also have one final question if and when i do format which is the best file system to use? and is there anyfile system other than FAT32 that will work with mac and windows?
The Mac can only read NTFS, not read.
My suggestion would be a) move the things to another already formatted external drive, b) get lots of DVD's and start making those archive copies that you've been putting off for so long, c) move the files onto the Mac temporarily and reformat the drive and then put them back on the external drive.
For maximum interoperability you'll want FAT32, if you are going to do that it'd probably be easier to offload the files onto your PC, reformat and then move them again.
I recently did this and I went through the files on the drive first and found that I could delete a lot of the files that I had on there so good luck. -
Cannot emtpy trash containing a file from FAT32 USB drive
Hi
I had copied a .app file from another mac over a network to my FAT32 USB drive. I then deleted the file from the USB drive per normal it went to trash. The problem is that i cannot empty this one file out of trash.
What iv tried thus far:
- I tried restarting.
- I tried dragging it back onto the USB and deleting again.
- I tried dragging it onto my desktop, upon which it asked for my system password, and then deleting again.
- I tried putting it back on the USB drive, restarting in windows XP, and tried deleting in windows.
None of the above has worked. The file is Zero KB. Windows gave an error with something about the file is not completed...?
Thanks in advance
cheersThanks but this did not work either. Below i have pasted the result form the terminal screen:
rm: random.app/Contents/Resources/BrushStrokes_TextOnly.Label.pox/Contents/Material /A317E08E-39E8-11D9-8C94-000A95C37E10.: No such file or directory
rm: random.app/Contents/Resources/BrushStrokes_TextOnly.Label.pox/Contents/Material : Directory not empty
rm: random.app/Contents/Resources/BrushStrokes_TextOnly.Label.pox/Contents: Directory not empty
rm: random.app/Contents/Resources/BrushStrokes_TextOnly.Label.pox: Directory not empty
rm: random.app/Contents/Resources/Picture-in-Picture_TextOnly.Label.pox/Contents/Ma terial/AFEBFBC8-39E8-11D9-8C94-000A95C37E10.: No such file or directory
rm: random.app/Contents/Resources/Picture-in-Picture_TextOnly.Label.pox/Contents/Ma terial: Directory not empty
rm: random.app/Contents/Resources/Picture-in-Picture_TextOnly.Label.pox/Contents: Directory not empty
rm: random.app/Contents/Resources/Picture-in-Picture_TextOnly.Label.pox: Directory not empty
rm: random.app/Contents/Resources/Postcard_TextOnly.Label.pox/Contents/.de0490.002/ BBB1382E-39E8-11D9-8C94-000A95C37E10.: No such file or directory
rm: random.app/Contents/Resources/Postcard_TextOnly.Label.pox/Contents/.de0490.002: Directory not empty
rm: random.app/Contents/Resources/Postcard_TextOnly.Label.pox/Contents: Directory not empty
rm: random.app/Contents/Resources/Postcard_TextOnly.Label.pox: Directory not empty
rm: random.app/Contents/Resources: Directory not empty
rm: random.app/Contents: Directory not empty
rm: random.app: Directory not empty -
After 10.7.2. update cannot see SD card reader in usb drive. Used to appear on desktop and start iPhoto but now nothing happens. It is recognised by system profiler (usb hub), but cannot find it anywhere. Any ideas?
Zap the PRAM and Reset the SMC, then try again.
-
Is there a way to configure NTFS file system on an NSS 324 SmartStorage unit. So far I can setup ext 3 or ext 4 but no option for NTFS. This unit should be joining a Windows Server 2008 R2 network and needs to be shared with all users. This unit will replace a File server running Win 2003 SP2.
Message was edited by: Hermann Koster
Thank you very much for your reply. The idea is to decommission the Windows file server which is running Windows Server 2003 SP2 operating system but is not running as a DC but just a member server. All this server is doing is providing file server services so my idea is to replace it with the NSS 324 box. My only concern is that when my NSS joins the domain all my users would be able to see and access network shares transparently, the same way they saw the former W2003 file server. After I transferred the data from File server I will use the same for NSS that was used for file server as well as same IP address and folders path as before.
Any suggestions or advice?
Once again thank you very much for your reply.
Cheers,The internal HDDs must be formatted in either EXT3 or EXT4 file system because NSS uses Linux OS. This is mainly because the RAM designed to fit with the customized Linux OS's size.
You can connect to an external HDD via a USB or eSATA port. The external HDD's file system can be NTFS, FAT32, AFT or EXT3/4 to be recognized for read/write. You can connect a 2TB USB/eSATA drive connec to the NSS via USB port to format your HDD for NTFS, AFT, FAT32, or EXT3/4 partition.
You can join the NSS to a Windows domainr so all domain users to access NSS. You cannot replace the NSS for the Windows 2003 SP2 server. They are two different products and do different jobs. Windows server is features sets server while the NSS is the files/data server.
Hope that helps!! -
Can't open office files from my usb drive
Dear forum
Sins a few weeks ago i am not able to open office file from my USB-drive.
However i can copy the file to the desktop and than i can open them.
I have this problme only (for as far i know) with office files.
greetings YpkobaIf the drive is NTFS format, the Mac can read, but not write thiose drives natively.
So the issue may be that the temp file and the output file cannot be created on the same drive. -
How to create a system recovery USB drive?
My U845-S406 crashes every 15 minutes with a BSOD referencing iastor.sys.
Multiple diagnostics say it is all good.
Multiple virus softwares say it is clean.
It crashes even quicker in safe mode.
I have the latest Toshiba raid drivers, but updated to a more recent Intel set. The error changes to iastora.sys, and goes back to iastor.sys when I switch back to the Toshiba drivers.
I booted holding down 0, and told it to restore; but it promptly crashes.
I made a W7 disk and tried to load it, but it promptly crashes.
As a last resort before throwing the computer out, I want to create a system recovery USB drive, format the harddrive and try recovering from the USB; but I don't have the Toshiba Recovery Media Creator (or any Toshiba software at all...) I downloaded a copy and ran it, but it says I don't have a HDD Recovery Area.
I know I have one because 1) I can access it by hold down 0, and 2)Partition Wizard showes it.
So, how can I create a system recover USB drive (or make Recovery Media Creator find the HDD recovery Area...)
Interestingly, the other day it spent 90 minutes installing a W7 update without a problem, but crashed immediately when done. Maybe that means something.Satellite U845-S406
Downloads here.
Please zip up a few of the corresponding *.dmp files from the C:\Windows\Minidump folder and attach them to your reply.
So the procedure in the section Creating recovery media (p. 53 in the User's Guide) doesn't work? Exactly where does it go wrong?
Satellite/Satellite Pro U800W Series User’s Guide
-Jerry -
Memory Management, Crit Structure Corrupt, Bad Pool Caller, ntfs file system error
So after freshly installing Win 8.1 I was happy, untill I started to play some games that I previously played on Win 7, I've started to get a whole heap of errors, I did have more written down but have lost the bit of paper they were written on.
Here are the list of errors I can remember.
Memory Management, Crit Structure Corrupt, Bad Pool Caller, ntfs file system error
Specs:
Operating System
Windows 8.1 Pro 64-bit
CPU
AMD Athlon II X2 250
35 °C
Regor 45nm Technology
RAM
6.00GB Dual-Channel DDR2 @ 400MHz (5-5-5-18)
Motherboard
ASUSTeK Computer INC. M3N-H/HDMI (Socket AM2 )
40 °C
Graphics
SyncMaster (1440x900@60Hz)
SAMSUNG (1440x900@60Hz)
ATI Radeon HD 4800 Series (Microsoft Corporation - WDDM v1.1) (Sapphire/PCPartner)
Storage
698GB Western Digital WDC WD7500AAKS-00RBA0 ATA Device (SATA)Adam
These are Related to
atikmdag.sys ATI Radeon Kernel Mode Driver. Yours is 2+ years old. I would update to the newest driver available.
Microsoft (R) Windows Debugger Version 6.3.9600.16384 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\Ken\Desktop\A040614-65203-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
************* Symbol Path validation summary **************
Response Time (ms) Location
Deferred SRV*H:\symbols*http://msdl.microsoft.com/download/symbols
Symbol search path is: SRV*H:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 8 Kernel Version 9600 MP (2 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 9600.16384.amd64fre.winblue_rtm.130821-1623
Machine Name:
Kernel base = 0xfffff803`be013000 PsLoadedModuleList = 0xfffff803`be2da9b0
Debug session time: Mon Apr 7 00:35:03.785 2014 (UTC - 4:00)
System Uptime: 0 days 0:08:48.334
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck 3B, {c0000005, fffff80001cf7d73, ffffd0002305c470, 0}
*** WARNING: Unable to verify timestamp for atikmdag.sys
*** ERROR: Module load completed but symbols could not be loaded for atikmdag.sys
Probably caused by : atikmdag.sys ( atikmdag+70d73 )
Followup: MachineOwner
0: kd> !analyze -v
* Bugcheck Analysis *
SYSTEM_SERVICE_EXCEPTION (3b)
An exception happened while executing a system service routine.
Arguments:
Arg1: 00000000c0000005, Exception code that caused the bugcheck
Arg2: fffff80001cf7d73, Address of the instruction which caused the bugcheck
Arg3: ffffd0002305c470, Address of the context record for the exception that caused the bugcheck
Arg4: 0000000000000000, zero.
Debugging Details:
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
FAULTING_IP:
atikmdag+70d73
fffff800`01cf7d73 8a040a mov al,byte ptr [rdx+rcx]
CONTEXT: ffffd0002305c470 -- (.cxr 0xffffd0002305c470;r)
rax=0000000000000000 rbx=ffffcf80021783a0 rcx=ffffcf8002334ff5
rdx=0000307ffdccb010 rsi=ffffcf8004734470 rdi=ffffcf80021783a0
rip=fffff80001cf7d73 rsp=ffffd0002305cea8 rbp=ffffd0002305cf00
r8=0000000000000006 r9=0000000000000000 r10=0000000000000384
r11=ffffcf8002334ff0 r12=0000000000000001 r13=ffffcf8004734470
r14=0000000000000000 r15=ffffcf8004734470
iopl=0 nv up ei ng nz na po nc
cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00010286
atikmdag+0x70d73:
fffff800`01cf7d73 8a040a mov al,byte ptr [rdx+rcx] ds:002b:00000000`00000005=??
Last set context:
rax=0000000000000000 rbx=ffffcf80021783a0 rcx=ffffcf8002334ff5
rdx=0000307ffdccb010 rsi=ffffcf8004734470 rdi=ffffcf80021783a0
rip=fffff80001cf7d73 rsp=ffffd0002305cea8 rbp=ffffd0002305cf00
r8=0000000000000006 r9=0000000000000000 r10=0000000000000384
r11=ffffcf8002334ff0 r12=0000000000000001 r13=ffffcf8004734470
r14=0000000000000000 r15=ffffcf8004734470
iopl=0 nv up ei ng nz na po nc
cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00010286
atikmdag+0x70d73:
fffff800`01cf7d73 8a040a mov al,byte ptr [rdx+rcx] ds:002b:00000000`00000005=??
Resetting default scope
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VERIFIER_ENABLED_VISTA_MINIDUMP
BUGCHECK_STR: 0x3B
PROCESS_NAME: csrss.exe
CURRENT_IRQL: 0
ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
LAST_CONTROL_TRANSFER: from fffff800025cf3d7 to fffff80001cf7d73
STACK_TEXT:
ffffd000`2305cea8 fffff800`025cf3d7 : ffffcf80`04734470 ffffcf80`04734470 00000000`00000000 ffffcf80`01f52450 : atikmdag+0x70d73
ffffd000`2305ceb0 ffffcf80`04734470 : ffffcf80`04734470 00000000`00000000 ffffcf80`01f52450 ffffd000`2305cf00 : atikmdag+0x9483d7
ffffd000`2305ceb8 ffffcf80`04734470 : 00000000`00000000 ffffcf80`01f52450 ffffd000`2305cf00 fffff800`025f48d3 : 0xffffcf80`04734470
ffffd000`2305cec0 00000000`00000000 : ffffcf80`01f52450 ffffd000`2305cf00 fffff800`025f48d3 ffffcf80`04734470 : 0xffffcf80`04734470
FOLLOWUP_IP:
atikmdag+70d73
fffff800`01cf7d73 8a040a mov al,byte ptr [rdx+rcx]
SYMBOL_STACK_INDEX: 0
SYMBOL_NAME: atikmdag+70d73
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: atikmdag
IMAGE_NAME: atikmdag.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 4fdf9bbd
STACK_COMMAND: .cxr 0xffffd0002305c470 ; kb
FAILURE_BUCKET_ID: 0x3B_VRF_atikmdag+70d73
BUCKET_ID: 0x3B_VRF_atikmdag+70d73
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0x3b_vrf_atikmdag+70d73
FAILURE_ID_HASH: {1ec4cdaf-008d-03dd-4ca9-ade1993441da}
Followup: MachineOwner
Wanikiya and Dyami--Team Zigzag -
Can i format ipod classic with NTFS file system on win7?
can i format ipod classic with NTFS file system on win7?
Not if you want to have an iPod as opposed to an ordinary external drive.
(60693) -
Portal on Unix cannot mount Windows File server
Hi Experts,
We had installed a NW 7.0 portal onto HP-UNIX server and integrated it with MS AD server. Now, we are facing an issue that we cannot mount windows files server when we tried to configured it with TREX. Had anyone tried this function or it is the limitation? Is the following statement still correct or do we have workaround solutions?
"If you are using the Microsoft Active Directory Service, you can only integrate documents into a Windows portal. The combination of Microsoft Active Directory Service and a UNIX portal is not supported."
Best RegardsHi Tom,
have a look at this link:
[http://help.sap.com/saphelp_nw04s/helpdata/en/ed/b334ea02a2704388d1d2fc3e4298ad/frameset.htm]
Your issue should work, but the prerequisite is for using the windows permissions:
"If you are using Microsoft Active Directory Service, you have to operate the Windows domain in mixed mode". If it is running in Native mode you cannot use the windows permissions. Nevertheless integrating documents into KM should work. The KM uses its own permissions instead.
Best regards,
Denis -
Hi Guys,
Im trying to create a repository .I have a single node OVM server and have presented two LUN's (Hitachi HUS110 direct attached (via FC))
I've created a server pool and unchecked the clustered server pool. I see the LUN's (physical disk from Oracle Virtual manager) .But when creating the repository i'm having this error
"OVMRU_002030E Cannot create OCFS2 file system with local file server: Local FS OVMSRVR. Its server is not in a cluster. [Thu Dec 04 01:33:10 EST 2014]"
Any steps i missed?Appreciate anyone's input
Regards,
RobertHi Robert,
did you actually add the OVS to the server pool, that you created? -
I am trying to install lightroom on a new computer and am getting error message 2203.database Cannot open database file system error 2147287037. Can anyone help me with this?
This site has some info
Error 2203 | Install | Creative Suite 4, 5, or 5.5 products or updates -
After boot can't mount SDS file systems on 3300 mount: cannot mount /dev/md
Hi
I have a SUNW,Netra-440 with two SE 3300 SCSI each with two controllers. The server was working fine but after a boot, it can not see the metadevices stored in the 3300.
I have tried restarting the SE3300 and a boot -r from ok prompt but I still can see those disks or partitions.
Metaset Import
metaset: log01: setname "appvol": no such set
mount all SVM filesystems for group appvol
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d101
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d102
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d103
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d104
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d105
mount: No such device
mount: cannot mount /dev/md/appvol/dsk/d106
metaset: log01: setname "dbvol": no such set
mount all SVM filesystems for group dbvol
mount: No such device
mount: cannot mount /dev/md/dbvol/dsk/d107
mount: No such device
mount: cannot mount /dev/md/dbvol/dsk/d108
i can see the devices in /dev/md/appvol but i can't mount them.
Any ideas what this could be? using metaset shows nothing, metastat -s dbvol hangs.
Am I missing some patch or am I missing something here? is the SE3300 damaged? or is it a problem with SDS (solstice). I have solaris 9.
The system was working fine until we had to boot and power off to perform power tests in the rack.
thanks
Ryck
this is the output of prtdiag
root@log01 >prtdiag
System Configuration: Sun Microsystems sun4u Netra 440
System clock frequency: 177 MHZ
Memory size: 8GB
==================================== CPUs ====================================
E$ CPU CPU Temperature
CPU Freq Size Implementation Mask Die Amb. Status Location
0 1593 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 - - online -
1 1593 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 - - online -
2 1593 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 - - online -
3 1593 MHz 1MB SUNW,UltraSPARC-IIIi 3.4 - - online -
================================= IO Devices =================================
Bus Freq Slot + Name +
Type MHz Status Path Model
pci 66 PCI5 scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1c,600000/scsi@1
pci 66 PCI5 scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1c,600000/scsi@1,1
pci 66 MB pci108e,abba (network) SUNW,pci-ce
okay /pci@1c,600000/network@2
pci 66 PCI4 scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1d,700000/scsi@1
pci 66 PCI4 scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1d,700000/scsi@1,1
pci 66 PCI2 pci100b,35 (network) SUNW,pci-x-qge
okay /pci@1d,700000/pci@2/network@0
pci 66 PCI2 pci100b,35 (network) SUNW,pci-x-qge
okay /pci@1d,700000/pci@2/network@1
pci 66 PCI2 pci100b,35 (network) SUNW,pci-x-qge
okay /pci@1d,700000/pci@2/network@2
pci 66 PCI2 pci100b,35 (network) SUNW,pci-x-qge
okay /pci@1d,700000/pci@2/network@3
pci 33 MB isa/su (serial)
okay /pci@1e,600000/isa@7/serial@0,3f8
pci 33 MB isa/su (serial)
okay /pci@1e,600000/isa@7/serial@0,2e8
pci 33 MB isa/rmc-comm-rmc_comm (seria+
okay /pci@1e,600000/isa@7/rmc-comm@0,3e8
pci 33 PCI0 SUNW,XVR-100 (display) SUNW,375-3290
okay /pci@1e,600000/SUNW,XVR-100
pci 33 MB pciclass,0c0310 (usb)
okay /pci@1e,600000/usb@a
pci 33 MB pciclass,0c0310 (usb)
okay /pci@1e,600000/usb@b
pci 33 MB pci10b9,5229 (ide)
okay /pci@1e,600000/ide@d
pci 66 MB pci108e,abba (network) SUNW,pci-ce
okay /pci@1f,700000/network@1
pci 66 MB scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1f,700000/scsi@2
pci 66 MB scsi-pci1000,30 (scsi-2) LSI,1030
okay /pci@1f,700000/scsi@2,1
============================ Memory Configuration ============================
Segment Table:
Base Address Size Interleave Factor Contains
0x0 2GB 4 BankIDs 0,1,2,3
0x1000000000 2GB 4 BankIDs 16,17,18,19
0x2000000000 2GB 4 BankIDs 32,33,34,35
0x3000000000 2GB 4 BankIDs 48,49,50,51
Bank Table:
Physical Location
ID ControllerID GroupID Size Interleave Way
0 0 0 512MB 0,1,2,3
1 0 1 512MB
2 0 1 512MB
3 0 0 512MB
16 1 0 512MB 0,1,2,3
17 1 1 512MB
18 1 1 512MB
19 1 0 512MB
32 2 0 512MB 0,1,2,3
33 2 1 512MB
34 2 1 512MB
35 2 0 512MB
48 3 0 512MB 0,1,2,3
49 3 1 512MB
50 3 1 512MB
51 3 0 512MB
Memory Module Groups:
ControllerID GroupID Labels Status
0 0 C0/P0/B0/D0
0 0 C0/P0/B0/D1
0 1 C0/P0/B1/D0
0 1 C0/P0/B1/D1
1 0 C1/P0/B0/D0
1 0 C1/P0/B0/D1
1 1 C1/P0/B1/D0
1 1 C1/P0/B1/D1
2 0 C2/P0/B0/D0
2 0 C2/P0/B0/D1
2 1 C2/P0/B1/D0
2 1 C2/P0/B1/D1
3 0 C3/P0/B0/D0
3 0 C3/P0/B0/D1
3 1 C3/P0/B1/D0
3 1 C3/P0/B1/D1
root@log01 >Hi,
thanks for your answer.
Yes format displays the physical devices, but metadb -i only shows the internal disks of the netra 440, not the ones in the 3320. metadb -s dbvol -i doesnt show anything.
metaset which is supposed to show me the metadevices, says the program is not registered.
cat /etc/lvm/md.tab has the configuration but since the scsi can be seen, the devices aren't mounted.
Any suggestions?
Cheers
Oscar
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848> bootdisk
/pci@1f,700000/scsi@2/sd@0,0
1. c1t1d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848> bootmirr
/pci@1f,700000/scsi@2/sd@1,0
2. c1t2d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848> spare1
/pci@1f,700000/scsi@2/sd@2,0
3. c1t3d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848> spare2
/pci@1f,700000/scsi@2/sd@3,0
4. c2t8d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> appvol
/pci@1c,600000/scsi@1/sd@8,0
5. c2t9d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol01
/pci@1c,600000/scsi@1/sd@9,0
6. c2t10d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol02
/pci@1c,600000/scsi@1/sd@a,0
7. c2t11d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol03
/pci@1c,600000/scsi@1/sd@b,0
8. c2t12d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol04
/pci@1c,600000/scsi@1/sd@c,0
9. c2t13d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol05
/pci@1c,600000/scsi@1/sd@d,0
10. c3t8d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> dbvol06
/pci@1c,600000/scsi@1,1/sd@8,0
11. c3t9d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free1
/pci@1c,600000/scsi@1,1/sd@9,0
12. c3t10d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free2
/pci@1c,600000/scsi@1,1/sd@a,0
13. c3t11d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free3
/pci@1c,600000/scsi@1,1/sd@b,0
14. c3t12d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> hotAPP
/pci@1c,600000/scsi@1,1/sd@c,0
15. c3t13d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> hotDB
/pci@1c,600000/scsi@1,1/sd@d,0
16. c4t8d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> APPVOLm
/pci@1d,700000/scsi@1/sd@8,0
17. c4t9d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1/sd@9,0
18. c4t10d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1/sd@a,0
19. c4t11d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1/sd@b,0
20. c4t12d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1/sd@c,0
21. c4t13d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1/sd@d,0
22. c5t8d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> d6Mirr
/pci@1d,700000/scsi@1,1/sd@8,0
23. c5t9d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free1M
/pci@1d,700000/scsi@1,1/sd@9,0
24. c5t10d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free2M
/pci@1d,700000/scsi@1,1/sd@a,0
25. c5t11d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> free3M
/pci@1d,700000/scsi@1,1/sd@b,0
26. c5t12d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>
/pci@1d,700000/scsi@1,1/sd@c,0
27. c5t13d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> hotDBm
/pci@1d,700000/scsi@1,1/sd@d,0
root@log01 >metadb -i
flags first blk block count
a m p luo 16 8192 /dev/dsk/c1t0d0s7
a p luo 8208 8192 /dev/dsk/c1t0d0s7
a p luo 16400 8192 /dev/dsk/c1t0d0s7
a p luo 16 8192 /dev/dsk/c1t1d0s7
a p luo 8208 8192 /dev/dsk/c1t1d0s7
a p luo 16400 8192 /dev/dsk/c1t1d0s7
r - replica does not have device relocation information
o - replica active prior to last mddb configuration change
u - replica is up to date
l - locator for this replica was read successfully
c - replica's location was in /etc/lvm/mddb.cf
p - replica's location was patched in kernel
m - replica is master, this is replica selected as input
W - replica has device write errors
a - replica is active, commits are occurring to this replica
M - replica had problem with master blocks
D - replica had problem with data blocks
F - replica had format problems
S - replica is too small to hold current data base
R - replica had device read errors
root@log01 >
root@log01 >metadb -i
flags first blk block count
a m p luo 16 8192 /dev/dsk/c1t0d0s7
a p luo 8208 8192 /dev/dsk/c1t0d0s7
a p luo 16400 8192 /dev/dsk/c1t0d0s7
a p luo 16 8192 /dev/dsk/c1t1d0s7
a p luo 8208 8192 /dev/dsk/c1t1d0s7
a p luo 16400 8192 /dev/dsk/c1t1d0s7
r - replica does not have device relocation information
o - replica active prior to last mddb configuration change
u - replica is up to date
l - locator for this replica was read successfully
c - replica's location was in /etc/lvm/mddb.cf
p - replica's location was patched in kernel
m - replica is master, this is replica selected as input
W - replica has device write errors
a - replica is active, commits are occurring to this replica
M - replica had problem with master blocks
D - replica had problem with data blocks
F - replica had format problems
S - replica is too small to hold current data base
R - replica had device read errors
root@log01 >metadb -s appvol -i
metadb: log01: setname "appvol": no such set
root@log01 >metaset
metaset: log01: metad client create: RPC: Program not registered
root@log01 >cat /etc/lvm/md.tab
# Copyright 2002 Sun Microsystems, Inc. All rights reserved.
# Use is subject to license terms.
# ident "@(#)md.tab 2.4 02/01/29 SMI"
# md.tab
# metainit utility input file.
dbvol/d57 1 1 c2t12d0s0
dbvol/d58 1 1 c4t12d0s0
dbvol/d4 -m dbvol/d57 dbvol/d58 1
dbvol/d55 1 1 c2t11d0s0
dbvol/d56 1 1 c4t11d0s0
dbvol/d3 -m dbvol/d55 dbvol/d56 1
dbvol/d61 1 1 c3t8d0s0
dbvol/d62 1 1 c5t8d0s0
dbvol/d6 -m dbvol/d61 dbvol/d62 1
dbvol/d59 1 1 c2t13d0s0
dbvol/d60 1 1 c4t13d0s0
dbvol/d5 -m dbvol/d59 dbvol/d60 1
dbvol/d53 1 1 c2t10d0s0
dbvol/d54 1 1 c4t10d0s0
dbvol/d2 -m dbvol/d53 dbvol/d54 1
###dbvol/d51 1 1 c2t9d0s0
dbvol/d52 1 1 c4t9d0s0
#dbvol/d1 -m dbvol/d51 dbvol/d52 1
dbvol/d1 -m dbvol/d52 1
# SOFT Partitions
dbvol/d129 -p dbvol/d5 -o 19933376 -b 526336
dbvol/d128 -p dbvol/d5 -o 19407008 -b 526336
dbvol/d127 -p dbvol/d5 -o 18880640 -b 526336
dbvol/d126 -p dbvol/d5 -o 10489952 -b 8390656
dbvol/d125 -p dbvol/d5 -o 2099264 -b 8390656
dbvol/d123 -p dbvol/d4 -o 4724864 -b 133120
dbvol/d122 -p dbvol/d4 -o 4460640 -b 264192
dbvol/d121 -p dbvol/d4 -o 4196416 -b 264192
dbvol/d120 -p dbvol/d4 -o 32 -b 4196352
dbvol/d119 -p dbvol/d3 -o 30972032 -b 526336
dbvol/d118 -p dbvol/d3 -o 10489952 -b 20482048
dbvol/d117 -p dbvol/d3 -o 4196416 -b 6293504
dbvol/d116 -p dbvol/d3 -o 32 -b 4196352
dbvol/d115 -p dbvol/d2 -o 8925408 -b 526336
dbvol/d114 -p dbvol/d2 -o 8399040 -b 526336
dbvol/d113 -p dbvol/d2 -o 7872672 -b 526336
dbvol/d112 -p dbvol/d2 -o 7346304 -b 526336
dbvol/d111 -p dbvol/d2 -o 5247072 -b 2099200
dbvol/d110 -p dbvol/d2 -o 1050688 -b 4196352
dbvol/d109 -p dbvol/d2 -o 32 -b 1050624
dbvol/d108 -p dbvol/d1 -o 33554496 -b 1572864
dbvol/d107 -p dbvol/d1 -o 32 -b 33554432
dbvol/d124 -p dbvol/d5 -o 32 -b 2099200
dbvol/d138 -p dbvol/d4 -o 38416608 -b 133120
dbvol/d137 -p dbvol/d3 -o 31498400 -b 264192
dbvol/d136 -p dbvol/d4 -o 21637312 -b 16779264
dbvol/d135 -p dbvol/d4 -o 4858016 -b 16779264
dbvol/d134 -p dbvol/d6 -o 69212288 -b 23070720
dbvol/d133 -p dbvol/d6 -o 46141536 -b 23070720
dbvol/d132 -p dbvol/d6 -o 23070784 -b 23070720
dbvol/d131 -p dbvol/d6 -o 32 -b 23070720
dbvol/d130 -p dbvol/d5 -o 20459744 -b 526336
root@log01 >metadb -s dbvol -i
metadb: log01: setname "dbvol": no such set
root@log01 >\ -
Automator to mount multiple ISO files on external USB drives
I have several ISO files on an external USB drive on a Mac mini. Double clicking on any of the ISO mounts it, one at a time.
I need to have an automator that mounts ALL ISO it can see on a given USB external drive. I have written an Apple script but that hangs up the Mac mini. I need help because I am not familiar with Applescript or Apple automator. I used Unix years ago, butg have a hard time with AppleScript.Macs can't normally write to NTFS drives:
http://discussions.apple.com/click.jspa?searchID=7426620&messageID=4582486
Your other problem sounds like another computer has the files open or application has the files open simultaneously. Try shutting down your Mac, and isolating your Mac from any network and try rebooting again in safe mode by holding the shift key at startup.
Maybe you are looking for
-
The MBP makes no noise after this. I can't recall ever dropping it. I purchased it in Jan 2011 (so I'm guessing it's a 2010 model? No idea. Has black keys & new, slim charger!) Happens when I've turned it off and on & when I restart. What do you t
-
Placed PDF missing text after re-exporting to PDF
I'm using OSX 10.6 with InDesign CS3 504. When I place PDFs into an InDesign file, and then PDF that InDesign file, some of the PDFs are missing text. All text boxes have been made from the same original text box, just modified for content, and shap
-
How to create own Selection Parameter for ME2M list
Dear Sir, We use ME2m tcode for getting list related to Purchase Order . We have been told that we can create our own "SELECTION PARAMETER" for ths report . Kindly guide us as what steps need to be done for this pl . With Thanks and Regards Sonia Mit
-
Convert smalldatetime type SQL format to Date in OBIEE
I have a SQL database which holds date in the smalldatetime type SQL format. I want to read this date in the OBIEE. How I can achieve this. I didn't find any direct CAST for this OBIEE Answers. thanks, Naresh
-
Kicking off a workflow via Event
Hi. How do you kick off a workflow via Event? I created a simple workflow with start--assign--stop. I created an event and subscription but when i raise it nothing happens. the workflow though runs when i use the launch process. What am i missing? I