Catalyst (3750 24 10/100/1000T) and (3750 12 SFP) Stacking Problems

Dear all
I'm having a very strange situation here (at least for me)
we have 4 core switches
2 x WS-C3750G-24T-S Catalyst 3750 24 10/100/1000T + IPB Image
and
2 x WS-C3750G-12S-S Catalyst 3750 12 SFP + IPB Image
Stack configuration is done this way
when the switches are powered on, the first two SFP core switches are seen as a single stack with the stack master LED turned green on the first switch
the other two (24 10/100/1000T) switches have the RPS LEDs always green, mode cannot be changed, and cannot be accessed by Console connection
but when the (24 10/100/1000T) are powered off, the first (SFP) switch in the stack reports that " Switch 3 and 4 has been removed from Stack "
which means they are stacked but there's something wrong, because
only the SFP ports are shown in the " Show interfaces status " , the ethernet ports of the bottom switches are not present !!!
can you please tell me what's the poblem ?

Dear Daniel
Sorry for my delayed response but i was actually quite busy
but the problem was actually in another sense
the default profile for the Catalyst 3750 SFP is the Aggregate SDM Template
while the 3750 10/100/1000 ethernet Switch Default SDM profile was Desktop profile
so i had an SDM mismatch
DATACENTER#sh switch detail
Switch/Stack Mac Address : 081f.f3cf.1c80
                                           H/W   Current
Switch# Role   Mac Address     Priority Version State
*1       Master 081f.f3cf.1c80     1      0       Ready
2       Member 081f.f3cf.5900     1      0       Ready
3       Member aca0.16ac.0180     1      2       SDM Mismatch
4       Member aca0.16a3.bc80     1      2       SDM Mismatch
         Stack Port Status             Neighbors
Switch# Port 1     Port 2           Port 1   Port 2
1        Ok         Ok                2        4
2        Ok         Ok                3        1
3        Ok         Ok                4        2
4        Ok         Ok                1        3
all i did was changing the default profile of the SFP switches into the Desktop Profile and problem was solved
switch 1 provision ws-c3750g-12s
switch 2 provision ws-c3750g-12s
switch 3 provision ws-c3750g-24t
switch 4 provision ws-c3750g-24t
system mtu routing 1500
ip subnet-zero
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface GigabitEthernet1/0/1
interface GigabitEthernet1/0/2
interface GigabitEthernet1/0/3
interface GigabitEthernet1/0/4
interface GigabitEthernet1/0/5
interface GigabitEthernet1/0/6
interface GigabitEthernet1/0/7
interface GigabitEthernet1/0/8
interface GigabitEthernet1/0/9
interface GigabitEthernet1/0/10
interface GigabitEthernet1/0/11
interface GigabitEthernet1/0/12
interface GigabitEthernet2/0/1
interface GigabitEthernet2/0/2
interface GigabitEthernet2/0/3
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet2/0/4
interface GigabitEthernet2/0/5
interface GigabitEthernet2/0/6
interface GigabitEthernet2/0/7
interface GigabitEthernet2/0/8
interface GigabitEthernet2/0/9
interface GigabitEthernet2/0/10
interface GigabitEthernet2/0/11
interface GigabitEthernet2/0/12
interface GigabitEthernet3/0/1
interface GigabitEthernet3/0/2
interface GigabitEthernet3/0/3
interface GigabitEthernet3/0/4
interface GigabitEthernet3/0/5
interface GigabitEthernet3/0/6
interface GigabitEthernet3/0/7
interface GigabitEthernet3/0/8
interface GigabitEthernet3/0/9
interface GigabitEthernet3/0/10
interface GigabitEthernet3/0/11
interface GigabitEthernet3/0/12
interface GigabitEthernet3/0/13
interface GigabitEthernet3/0/14
interface GigabitEthernet3/0/15
interface GigabitEthernet3/0/16
interface GigabitEthernet3/0/17
interface GigabitEthernet3/0/18
interface GigabitEthernet3/0/19
interface GigabitEthernet3/0/20
interface GigabitEthernet3/0/21
interface GigabitEthernet3/0/22
interface GigabitEthernet3/0/23
interface GigabitEthernet3/0/24
interface GigabitEthernet4/0/1
interface GigabitEthernet4/0/2
interface GigabitEthernet4/0/3
interface GigabitEthernet4/0/4
interface GigabitEthernet4/0/5
interface GigabitEthernet4/0/6
interface GigabitEthernet4/0/7
interface GigabitEthernet4/0/8
interface GigabitEthernet4/0/9
interface GigabitEthernet4/0/10
interface GigabitEthernet4/0/11
interface GigabitEthernet4/0/12
interface GigabitEthernet4/0/13
interface GigabitEthernet4/0/14
interface GigabitEthernet4/0/15
interface GigabitEthernet4/0/16
interface GigabitEthernet4/0/17
interface GigabitEthernet4/0/18
interface GigabitEthernet4/0/19
interface GigabitEthernet4/0/20
interface GigabitEthernet4/0/21
interface GigabitEthernet4/0/22
interface GigabitEthernet4/0/23
interface GigabitEthernet4/0/24
that's it !
: D
cheers

Similar Messages

Drag the 100 files and drop at treenode problem

< Problem >
I drag 20 files & drop those at one Treenode,
Now, those files got transparent background color
and stay on the treenode for a while and then disappear.
to the right--side--of Panel, where it should be.
--> Possible solution for this?
Please, let me know.

Please post a small, compilable and runnable example of what your problem is

Alternative switch to Cisco Catalyst 3750v2-24FS and 3750-24FS

I`m looking for an alternative to these two switches:
1. WS-C3750V2-24FS-S Cisco Catalyst 3750V2-24FS Switch with 24 100FX SFP + 2 Gigabit Ethernet SFP Ports
2. Cisco Catalyst 3750-24FS (WS-C3750-24FS-S 100BASE-FX)
They are now EOL and not available.
I have a campus style network and need to be able to connect multiple 100FX fibre switches back to a central switch. The 1st unit uses 100FX SFP modules and the second has in-built 100FX ports. I`m struggling to find anything from Cisco that will give me multiple (i.e 12+) 100FX ports.
Could anyone please point me in the right direction?
Many thanks,
Paul

Hi Paul ,
Replacement for both switch is WS-C3650-48TS-S.
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps5528/eos-eol-notice-c51-730227.html
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps5023/end_of_life_c51-687707.html
Regards
Don't forget to rate helpful posts
Sent from Cisco Technical Support iPhone App

Comparison between 3750 and 3750-metro

hi folks,
is there any links which will provide me on the comparison between 3750 and 3750-metro? for exapmple, isis is not support on 3750 but it support on 3750-metro. The product information from cisco site is insufficient in term of the main differences :p
rgd
josh.w

Hi Josh,
The Cisco Catalyst 3750 Metro Series is built for Metro Ethernet access in a customer location, enabling the delivery of more differentiated Metro Ethernet services. These switches feature bidirectional hierarchical QoS and Traffic Shaping, intelligent 802.1Q tunneling with class-of-service (CoS) mutation, VLAN translation, MPLS, EoMPLS, and Hierarchical Virtual Private LAN Service (H-VPLS) support, and redundant AC or DC power. They are ideal for service providers seeking to deliver profitable business services, such as Layer 2, Layer 3, and MPLS VPNs, in a variety of bandwidths and with different SLAs.
The metro switches have the PXF chips (which allow hierarchical QoS on the 2 "WAN" GigE ports, so several logical links can share a connection, and have soft bandwidth limits).
For more details on 3750-M switches have a look at this link
http://www.cisco.com/en/US/products/hw/switches/ps5532/products_qanda_item09186a00801eb822.shtml
HTH
Ankur
*Pls rate all helpfull post

Stacking 3750 switches with EMI and SMI versions

Hi!,
Is it possible to have in a stack Catalyst 3750 with EMI version and Catalyst 3750 with SMI?. In my case, it is a WS-C3750G-12S-E with WS-C3750-48PS-S. I didn't find clear information about this issue. I know different major releases are not compatible but nothing is mentioned about the feature set.
Thanks,
MONICA

Hi,
It's possible but not recommended. If you decide to do this you should buy 2 EMI so that if the master fails the backup can still route traffic. (Having 2 EMI is TAC supported, even if the rest is SMI - not sure about just having one EMI and one SMI)
HTH - plz rate if useful.
Andrew.

Connection between 5508 WLC and 3750-24PS switch

I have to realize a connection between an 5508 WLC and 3750 switch using one SFP cable. I found on Cisco documentation some reference about two different SFP cables.
The first one is CAB-SFP-50CM, but this is used to interconnect two 3560 switches.
The second is SFP-H10GB-CU1M. This one has SFP+ transceivers on both ends which I don’t know if are compatible with the standard SFP ports that can be found both on WLC and switch.
My question is if I can use one of these cables in order to connect my devices, or if you know other one piece SFP cables.
Many thanks

I know that you can use those SFP transceivers, but I want to know if someone tried to use the SFP-H10GB cables for this kind of connection. Because I saw on another vendor website that the SFP+ cables are compatible with standard SFP ports, and I wanted to see if it is the same for Cisco cables too.
Regards

How often should the Cisco 6509 and 3750 switches be rebooted? Does Cisco have a best practice recommendation?

How often should the 6509's and 3750's switches be rebooted?
Does Cisco have a best practice document on this and recommendation how long the switch should be up before it gets rebooted?
Why is a reboot needed if there are no indications of issues on the log?

I'd agree with Larry here.
If you're not seeing any issues with your IOS revision and there are no relevant PSIRTs (security notices applicalble to features and or exposure of your device requiring an IOS upgrade) then you can go a very long time without rebooting, if ever.
I'm sure it's far from a record, but our corporate distribution router that supports >1000 downstream devices day in and day out has never been rebooted since installation just over 5 years ago. I have a top of rack Layer 2 switch (2900 series running CatOS) that's almost at 10 years.
That said, you should have some monitoring scheme that assures you everything is healthy. But as long as memory and cpu are happy, the device will run forever.

QoS on 3560, 2960 and 3750 does not work (Policy-map).

Hi
I am tryng to configure QoS on 3 switches (2960, 3560 and 3750) with this configuration:
mls qos
class-map match-all QOS_DATA_CLASS
match access-group name QOS-DATA
class-map match-all QOS_DEFAULT_CLASS
match access-group name QOS-DEFAULT
class-map match-all QOS_VOICE_CLASS
match access-group name QOS-VOICE
class-map match-all QOS_SIGNALING_CLASS
match access-group name QOS-SIGNALING
policy-map QOS-SOFTPHONE-POLICY
class QOS_DEFAULT_CLASS
set dscp default
class QOS_SIGNALING_CLASS
set dscp cs2
class QOS_DATA_CLASS
set dscp cs1
class QOS_VOICE_CLASS
set dscp cs3
interface GigabitEthernet0/34
no switchport
ip address 10.10.11.1 255.255.255.252
ip ospf network point-to-point
priority-queue out
service-policy input QOS-SOFTPHONE-POLICY
interface GigabitEthernet0/47
switchport access vlan 150
spanning-tree portfast
service-policy input QOS-SOFTPHONE-POLICY
ip access-list extended QOS-DATA
permit tcp any any eq 22
permit tcp any any eq 465
permit tcp any any eq 143
permit tcp any any eq 993
permit tcp any any eq 995
permit tcp any any eq 1914
permit tcp any any eq ftp
permit tcp any any eq ftp-data
permit tcp any any eq smtp
permit tcp any any eq pop3
ip access-list extended QOS-DEFAULT
permit ip any any
ip access-list extended QOS-SIGNALING
permit tcp any any range 2000 2002
permit tcp any any range 5060 5061
permit udp any any range 5060 5061
ip access-list extended QOS-VOICE
permit udp any any range 16384 32767
but when I check the show commands I see that QoS is not working.
CoreA#sh policy-map interface g0/34
GigabitEthernet0/34
Service-policy input: QOS-SOFTPHONE-POLICY
Class-map: QOS_DEFAULT_CLASS (match-all)
3 packets, 198 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DEFAULT
Class-map: QOS_SIGNALING_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-SIGNALING
Class-map: QOS_DATA_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DATA
Class-map: QOS_VOICE_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-VOICE
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
CoreA#sh policy-map interface g0/47
GigabitEthernet0/47
Service-policy input: QOS-SOFTPHONE-POLICY
Class-map: QOS_DEFAULT_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DEFAULT
Class-map: QOS_SIGNALING_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-SIGNALING
Class-map: QOS_DATA_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-DATA
Class-map: QOS_VOICE_CLASS (match-all)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: access-group name QOS-VOICE
Class-map: class-default (match-any)
0 packets, 0 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
What do I do bad?
The flow is the next:
Computer with CIPC --------> Switch 2960 or 3560 or 3750 ------------------> switch core ---------------> CIPC
I have wireshark in a port mirror on switch 2960, 3560 and 3750. In wireshark I always see the packets marked with default label.
I hope you can help me.
Regards.

Try this config:
policy-map QOS-SOFTPHONE-POLICY
class QOS_VOICE_CLASS
set dscp cs3
class QOS_SIGNALING_CLASS
set dscp cs2
class QOS_DATA_CLASS
set dscp cs1
class class-default
set dscp default
BR

URGENT: MPLS P/ PE support on 7600/Sup720-BXL and 3750 Metro switch

I'm need to design a MPLS network for a Cable Operator.
They will start small with some Cisco CMTS doing MPLS-PE and needing only two devices to aggregate these PE and delivering Services (Internet connection, VoD, ...) , so they will need to work has P/PE.
For that I want to know if it's possible to:
1 - Use 3750 Metro and 7600/Sup720-BXL as P and PE
2 - Who many customers (L2VPN/VLANs and/or L3VPN/VRF) can they support?
Searching in CCO I found these values/features but, need URGENT to check:
1 - sup720-bxl supports P and PE but 3750 only PE?
2 - 3750 supports 1024 VLANs and 8,192 MPLS labels but no values on L3VPN/VRF?
SUP720 supports more than 1000 VRF?
Really need urgent HELP on this design/capabilities for these two devices.
Thanks in advance,
MP
Network Consultant - CCIE

before you even get anywhere close to the numbers of L2/L3 on a 7200 I would seriously consider asking what throughput you can get through a 7200 with MPLS, QOS, L3vpns and L2vpns configured. I have done this testing already but dont think it is appropriate to quote the figures publically.

WLC 7.4.100.60 and roaming problems on 8500

Hello,
After installing an 8500 controller on 7.4.100.60 and migrating 1000 APs do this controller, we have the following problems:
[1] clients get disconnected and loose sessions (note: client is mobile gun and is heavily mobile). I have the impression there are more coverage holes. This might be due to bug CSCue13108, but says fixed in 7.4.100.60, we wil be upgrading to 7.4.110.0 anyway shortly.
[2] we have lots of L3 roaming problems between clients, especially when clients roam between old WISM controller and new 8500 controller. They don't roam, they get disconnected and reconnected, resulting in ip address change, resulting in sessions loss. Old controller still runs 7.0.230.0 but compatibility matrix says these two versions are L3 roaming compatible.
However, the release notes of 8500 mention this: "Cisco 8500 Series Controller cannot be configured as a guest anchor controller. However, it can be configured as a foreign controller to tunnel guest traffic to a guest anchor controller in a DMZ"
Because Layer 3 roaming is similar to guest traffic tunneling, does this mean that the 8500 can be the initiator of a L3 roam tunnel, but cannot be the endpoint of a L3 roam tunnel ?
We have done a test that seems to confirm this: client starts on 8500 in state "local", goes to AP on old controller (7.0.230.0), but roam doesn't work. Client gets re-associated with ip address change. Then when moving back to the 8500 controller, the client does roam successfully, keeps its ip address in the 7.0.230.0 vlan and gets status "foreign" on 8500 controller. controllers are in same mobility group and mobility connections are all up.
In the 7.5 release notes, this limitation is not mentioned anymore. Does it mean it is solved and 8500 can be used as guest anchor controller in 7.5 ??
regards,
Geert

[2] we have lots of L3 roaming problems between clients, especially when clients roam between old WISM controller and new 8500 controller. They don't roam, they get disconnected and reconnected, resulting in ip address change, resulting in sessions loss. Old controller still runs 7.0.230.0 but compatibility matrix says these two versions are L3 roaming compatible.
Roaming from one AP to another that shares the same controller is totally different with inter-controller roaming, which you have now. I believe WiSM-1 has 180 ms compared to the 90 ms on a 5508. And this time difference means alot.
So when your client goes from one controller to another, they actually have to do a full re-authentication to the new controller.
I presume both the old and new controller are in the same Mobility Group?
However, the release notes of 8500 mention this: "Cisco 8500 Series Controller cannot be configured as a guest anchor controller. However, it can be configured as a foreign controller to tunnel guest traffic to a guest anchor controller in a DMZ"
Pffft! That'll be the most expensive Guest Anchor Controller if I follow this solution.

I resized the window to 150% and now I can't get it back to 100% view and keep it that size. How do I get it back to the right size?

I resized the adobe window to 150% and now I can't get it back to the 100% size and keep it that size. How do I get the original 100% back and keep it that size?

Hi Linda,
To control the page zoom option you can also go to Edit> Preferences> Page Display.
Regards,
Rave

Mdnsresponder will not quit. Consumes above 100% CPU and kills my battery. Also causes my fan to run constantly and my computer to get extremely hot. Force quitting doesn't work. It just comes back.

The mdnsresponder will not quit. Consumes above 100% CPU and kills my battery. Also causes my fan to run constantly and my computer to get extremely hot. Force quitting doesn't work. It just comes back. I posted about this earlier and never got an answer. Somebody, please help.
Thanks.

mDNSResponder is a background process that runs all the time. If you kill it, it's relaunched automatically.
Please launch the Console application and select "system.log" from the file list. Enter "mDNSResponder" (without the quotes) in the search field. Post a sample of the log messages in the Console window -- only one example of each repeated message, please.

Why do my PRO-100 black and white prints have a color tint?

I am printing on the PIXMA Pro-100 printer and sometimes, for no apparent reason (?), my black and white prints will have a color tint (usually a "redish brown"), and then when printing again... same print, same settings... the same print will be fine, neutral with no tint at all.
Any ideas why?
Also (maybe related?) I don't understand why the Photo-Cyan and Magenta ink cartridges are being depleted when I am NOT printing color, but only Black and White. Am I missing something? When setting up for printing I always make sure the "Black and White Print" feature is selected in the settings dialog "Quick Setup". Doesn't this insure that only the black and grey inks are used as long as I am not "toning"? In other words... if ONLY the black and grey inks are used, isn't the print supposed to be a neutral black and white print? Again... am I missing something?
FYI:
I am printing on Canon Pro Luster and Plus Semi-Gloss papers.
Under "Options - Color Management" I have selected:
(color handling) Photoshop Elements Manages Colors
(image space) Adobe RGB (1998)
(printer profile) Canon PRO-100 <LU> 1/2 Photo Paper Pro Luster
(rendering intent) Perceptual
Solved!
Go to Solution.

It looks like you have the settings pretty close. But the fact is all printers use all their cartridges to print B&W.
Whoa, why?
Yes it is true and the reason is this. B&W consists of 256 shades of gray. From totaly black which is 0 to white which is 256.
If you have just one, two or three cartridges to make 256 different blacks and grays all the way to white, it simply isn't possibile.
The ony thing a printer can do is, amount of ink and how long. So it makes up for this by using all it's cartridges. However, in Canon it seems like the Pro-100 tints show up more than it should. There are dedicated B&W printers but they are designed differently to accomplish true B&W.
The tint will be different on different papers. You can experiment to find the paper that does best for you. Try a more gloss type paper and see if you like the B&W. You can try Red River papers, too. They will assist you in picking a good B&W paper.
You can also experiment with filters in PSE. Adding a little blue may help. Just give it a try.
But the bottom line is you are no doing anything wrong. It is just the charchter of the beast.
EOS 1Ds Mk III, EOS 1D Mk IV, EF 50mm f1.2 L, EF 24-70mm f2.8 L,
EF 85mm f1.2 L II USM, EF 70-200mm f2.8 L IS II,
Sigma 120-300mm f2.8 EX APO, Photoshop CS6, ACR 9, Lightroom 6

How to avoid the hard limit of 100 column and items per page?

I have created a Form on a Table with Report. I need to create/edit approximately 175 items. The items on the Form have a limit of 100 column and items per page. What is the best way to carry the remaining items to another Form and doing an insert or update? or is the 100 column limit on the insert/update per table as well?
Thank You.

Hi Rick,
The 100 item limit is on a page, not a table, so you shouldn't have any trouble with your insert or update processes.
Here's a thought:
Report currently has a column that links to the first page of items (page 14) with the retrieved row. Presumably you also have a Add New button on the report page that links to page 14 for a new row.
Define a Next button on page 14 that branches to the second page of items (page 16). Also define a Previous button on page 16 to return to page 14. But page 16 would be the only page with a Save button.
Now, if user clicks Add New, user will get a blank page 14. Once user enters the info and passes validation they click Next and will be sent to page 16 to enter the remaining info and Save.
If user clicks one of the column links, they will be brought to page 14 with the clicked row - they can change whatever info there and click Next, or just click Next, to get to page 16. After any changes are made, they click Save.
I'm assuming you've been thru the tutorials and realize that you'd really have two Save buttons defined for page 16 - one conditional on your primary key item having a value (existing record) and one conditional on it being null (new record) - check out the tutorials for more info, but this is how the application would know whether to run an insert process or an update process.
Hope this all makes sense and can help,
John

3com 3c90x fast ethernet 10/100 card and solaris 8 (x86)

I am completely new to solaris, I am trying to install solaris 8 for x86 in a computer with a 3com 3c90x fast ethernet 10/100 card and looks like the o.s. does not recognize it at first. Reading the 02/02 hardware compatibility list I found out that this device needs to be configured after the instalation (with the device configuration floppy). The point is... I have no clue on how to do this. Can someone help me with that or point me in the right direction? The machine is ment to be a back-up file server.
Since now, thanks for the attention.
lucdepaula

Maybe the 3Com card works by adding it's PCI-ID to /etc/driver_aliases:
http://sun.drydog.com/faq/s86faq.html#6.7
Maybe you also need the (unoffical) elxl driver update for some of the
newer 3Com 3c905 variants:
http://groups.yahoo.com/group/solarisonintel/files/elxl.tar

Catalyst (3750 24 10/100/1000T) and (3750 12 SFP) Stacking Problems

Similar Messages

Maybe you are looking for