CCM and CME integration, SIP

Hello,
This question probably was asked many times, but I'm still not able to figure out how to setup a SIP trunk between CCM (v.4.1) and CME. I read all articles about IP-to-IP SIP protocol, played around with different setting, but no luck. Can you point me to the right direction? Example configuration will be very helpful. Basically I need to make calls between 4 digits extensions between offices and to route OffNet calls.
THANK YOU!!!

Hello,
Thank you for your help. I was able to create the trunk and I'm able to make calls between CCM and CCME.
Here is my config:
SIP trunk on CCME router:
dial-peer voice 20 voip
destination-pattern [area code]80823..
session protocol sipv2
session target ipv4:10.181.0.200
session transport tcp
dtmf-relay rtp-nte
codec g711ulaw
no vad
The Trunk on CCM is simple:
- Call Classification - OnNet;
- MTP - checked;
- Destination Address - IP on CCME;
- ports - 5060, 5060, TCP, 711ulaw;
- significant digits - 4;
Thanks!

Similar Messages

Unity 4.2(1) and CME 4.1(0) Error - CME ports reregister every 60 seconds

Hello,
I have an integration between Unity 4.2(1) and CME 4.1(0) which, until Friday last week was working fine.
I got a complaint that users couldn't get theri voicemail and have found that the ports on CME unregister and register every 60 seconds (see below)
Has anyone seen this before and knows a solution.
I've checked that the TSP v8.2(1) is supported for both and I've completely removed the config from CME and redone, but no change.
Any Ideas ?
Thanks
Chris
MA-CAS-2851-01#
Apr 12 14:31:09.703: %IPPHONE-6-UNREGISTER_ABNORMAL: ephone-90:CAS-VI1 IP:10.15.28.111 Socket:14 DeviceType:Phone has unregistered abnormally.
Apr 12 14:31:09.707: %IPPHONE-6-REGISTER_NEW: ephone-90:CAS-VI1 IP:10.15.28.111 Socket:7 DeviceType:App has registered.
MA-CAS-2851-01#
Apr 12 14:31:29.931: %IPPHONE-6-UNREGISTER_ABNORMAL: ephone-91:CAS-VI2 IP:10.15.28.111 Socket:22 DeviceType:Phone has unregistered abnormally.
Apr 12 14:31:29.931: %IPPHONE-6-REGISTER_NEW: ephone-91:CAS-VI2 IP:10.15.28.111 Socket:14 DeviceType:App has registered.
MA-CAS-2851-01#

Hi,
I have already booted the server, had no choice as Unity shut down completely when I made a change in UTIM !
The only events I see are in the App log of EventViewer and they're merely telling me via a TSP error that a port has unregistered.
The Unity server has multiple integrations, ports : 24 to CM4, 6 to CM7 and 2 to CME. (32 ports in total)
Only the CME has any issues and it was working perfectly well for the last 3 months !
Any thoughts?
Chris

Building CME with SIP vs. SCCP Phones

We currently have 4 CME Systems with SCCP phones. Recently, it was discuss by our upper management to start using SIP phones. Right now the system I have configured are using a PRI for dialtone with POTS lines for backup. What needs to different on the config to use SIP? Do I replace the 'telephony-service' and current 'dial-peers' or add to them?
This is all new to me and I still have not been able to attend any formal training.
Would there ever be a reason to use SIP and SCCP phones on the same system and would that even work?
Any help is appreciated!

Aha.... that's a different question.
The choice of your trunking protocol (PRI versus SIP versus something else like FXO/analogue) is largely independent of the protocol the handsets use. You can use SCCP for your handsets and then use SIP trunking into a provider for your external calls. The CME Router will handle the signalling translation between SCCP and SIP for you.
Like everyone else here, I would always use SCCP for the handsets. Whilst Cisco are improving SIP handset features all the time between releases you still can't do everything you that you can do with SCCP. You would also need version 15 to support some of the more useful SIP handset stuff including Extension Mobility, and my own personal view of the code quality on the version 15 trains would use such language that it can't be mentioned here.
SCCP to the handset and trunking over SIP is perfectly valid and I've used it many times with great success.
Hope this helps. Barry

Ccme cwd fail coming from ccm (ccm h323 ipip ccme sip)

I have a ccm---h323---ipipgw----sip---ccme. in other words the comunication between ccm and ccme is via ipipgw first h323 and then sip.
the direct call work fine but if the ccme ext have cwd to another ccme ext the call fail. I made a test calling direct from ccm to ccme via sip trunk and work fine. only on ipipgw with cwd fail. any ideas?

the ccm is 4.1.3, the ios ipipgw is
flash:c2800nm-adventerprisek9_ivs-mz.124-3g.bin
so : I made some tests: using the ipipgw on ccm like gateway only and other test using trunk. with or without mtp check. so the result is the same. I configured the ipipgw h323 to h323 and work fine but h323 to sip not working only on cwd to internal ccme ext.
direct call work fine.
un ipipgw with h323 to sip work fine only on direct call. but not on fwd. seem to be on ccme side. I actived a error debug on ccme via ccsip error:*Nov 8 01:11:16.343: //109/806226DC4200/SIP/Error/sipSPIProcessCallInfoHeader: Call-Info header with for Unsolicited Notify Absent,Disabling Unsolicited Notifies
another test was sip trunk direct ccm to ccme and work fine the fwd. only ipipgw via h323 to ccm and sip to ccme

UC560, ATA187s and CME 9 questions.

I originally posted this in the Community forum, not the Support Community forum....so I will report here.
We recently purchased a UC560 along with some ATA187's only to find out that the ATA's are not supported out of the box...
Everyone says "Its supported in CME 9", so how does one get CME 9 on the UC560? I cannot find docuementation anywhere that shows this.
Heck is it even possible to get CME 9 running on the UC560? I see that I would need an IOS update as well, but again I cannot find the correct IOS version for the UC560.
Any help would be appreciated.
Brian

Hi Brian,
Sorry to hear about the compatibility problems your facing with the new gear you purchased. I understand your frusturation, there have been many times where the compatibility matrix and I didn't get along.
First thing I want to mention is a nifty post I found by another user on the forum, jkittle99:
CME 8.6 - ATA 187 - not working
Try this - I just did with an ATA187 and CME 8.6, and had things working
1) Lie to CME and tell it that the device is an 7961
2) 'create profile' to generate the XML config file
3) rename / copy the XML config file (SEPxxxxx.cnf.xml) to ATAxxxxx.cnf.xml (since the ATA has a different filename structure than the 7961).
4)reboot, and enjoy
Note: I haven't fully vetted all the extra 'what if's with this, but I do have an ATA187 registered and it can make/take calls.
Josh
I'm not a CCA user, but alternatively you can set the ATAs up via SIP as Paolo mentioned from the CLI. This looks to be a decent guide, though not specific to the UC560:
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_example09186a00808f33eb.shtml
Theres a great deal more information in that article than you really need, as it is looks like theyre setting up the whole cme for just the sip phones, but you can go through and pick out the pertinent parts. Just remember to backup before you give this a go.
I wish I had a ATA187 to test with
Best,
David

Oracle Portal and Discoverer Integration

Portal Version: 9.0.2.0.1
RDBMS Versjion: 9.0.1.3
OS/Vers. Where Portal is Installed:: Suse 7 SLES
Error Number(s)::
Oracle Portal and Discoverer Integration
We're trying to integrate Discoverer with Portal unsuccessfully.
We made many things in accordance with oracle's documentation until add discoverer portlets (worksheet and list of workbooks) in a test page.
In view mode, the worksheet portlet shows the error:
"The portlet has not been defined. The publisher must define the portlet by clicking on Edit Defaults for the portlet on the edit mode of this page. Please contact the publisher of this page."
We think we have to edit properties before. Is this? Anyway edit worksheet portlet crashes between step 1 and 2. The error is: "The listener returned the following Message: 500 Internal Server Error".
We have a public conection created in EM and a discoverer application which can be viewed using plus or viewer.
Furthermore, it's not possible delete the added portlets neither the page that contain it. The error at delete is:
Error: An unexpected error occurred: User-Defined Exception (WWC-44082)
(WWC-00000)
An unexpected error has occurred in portlet instances: User-Defined Exception (WWC-
44846)
An unexpected error occurred: User-Defined Exception (WWC-43000)
The following error occurred during the call to Web provider:
oracle.portal.provider.v2.PortletNotFoundException
at oracle.portal.utils.v2.ContainerException.fillInStackTrace(Unknown Source)
at java.lang.Throwable.<init>(Throwable.java:78)
at java.lang.Exception.<init>(Exception.java:29)
at oracle.portal.utils.v2.ContainerException.<init>(Unknown Source)
at oracle.portal.provider.v2.PortletException.<init>(Unknown Source)
at oracle.portal.provider.v2.PortletNotFoundException.<init>(Unknown Source)
at oracle.disco.portlet.provider.DiscoPortletPersonalizationMgr.destroy
(DiscoPortletPersonalizationMgr.java:65)
at oracle.portal.provider.v2.DefaultPortletInstance.deregister(Unknown Source)
at oracle.webdb.provider.v2.adapter.soapV1.ProviderAdapter.deregisterPortlet
(Unknown Source)
at java.lang.reflect.Method.invoke(Native Method)
at oracle.webdb.provider.v2.utils.soap.SOAPProcessor.doMethodCall(Unknown Source)
at oracle.webdb.provider.v2.utils.soap.SOAPProcessor.processInternal(Unknown Source)
at oracle.webdb.provider.v2.utils.soap.SOAPProcessor.process(Unknown Source)
at oracle.webdb.provider.v2.adapter.SOAPServlet.doSOAPCall(Unknown Source)
at oracle.webdb.provider.v2.adapter.SOAPServlet.service(Unknown Source)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:336)
at com.evermind.server.http.ResourceFilterChain.doFilter
(ResourceFilterChain.java:59)
at oracle.security.jazn.oc4j.JAZNFilter.doFilter(JAZNFilter.java:283)
at com.evermind.server.http.ServletRequestDispatcher.invoke
(ServletRequestDispatcher.java:523)
at com.evermind.server.http.ServletRequestDispatcher.forwardInternal
(ServletRequestDispatcher.java:269)
at com.evermind.server.http.HttpRequestHandler.processRequest
(HttpRequestHandler.java:735)
at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:151)
at com.evermind.util.ThreadPoolThread.run(ThreadPoolThread.java:64)
(WWC-43147)
Edit properties for portlet List of Workbook works but in view mode we have the error in the portlet area:
"Failed to refresh portlet. Please verify that the information used to create the
portlet instance or customization is still valid. Otherwise, please contact your
iAS administrator. oracle.discoiv.controller.FatalControllerException:
DiscoNetworkException - Nested exception: org.omg.CORBA.OBJECT_NOT_EXIST: minor
code: 0 completed: No null"
Any ideas?
Thanks

Hi there,
Have you applied any patches to 9ias since it was first installed? We had the same problem and had to apply a couple of patches to get the portlets working.
1. Apply the 9.0.2.53.16 one-off patch for Oracle 9iAS Discoverer which takes Discoverer up to 9.0.2.53.16. This patch appears to be password protected and you need to get someone at Oracle support to give you a password.
2. Apply the Discoverer Portlet Provider: 9.0.2.53.00c patch (patch no. 2595444) which gives you a new discportal.xsl file that actually works. It's this second step that solves your problem but you need to do step 1 before this. This is password protected as well.
3. As you've upgraded Disco on the server to 9.0.2.53, you'll need to upgrade Disco Admin & Desktop within your 9iDS installation using patch no. 2555265. This is because Disco 9.0.2.53 uses an upgraded EUL that Disco Admin & Desktop need to be patched to use.
This was the course of action Oracle support advised us about nine months ago. Of course they may have released a further patch to Disco that does 1 & 2 in one go, but we regularly carry out steps 1 and 2 on servers we use and we can use the Disco portlets successfully.
Hope this helps
Mark Rittman
[email protected]

Unit testing and system integration testing for crystal report

Hi gurus,
I am creating crystal report by oracle procedure, will you please tell me how to do unit testing and system integration testing? appreciate very much.

The focus of this forum is report design. The actual testing of reports would be subject to your own internal policies and procedures.
Jason

Question regarding MM and FI integration

Hi Experts
I have a question regarding MM and FI integration
Is the transaction Key in OMJJ is same as OBYC transaction key?
If yes, then why canu2019t I see transaction Key BSX in Movement type 101?
Thanks

No, they are not the same. The movement type transaction (OMJJ) links the account key and account modifier to a specific movement types. Transaction code (OBYC) contains the account assignments for all material document postings, whether they are movement type dependent or not. Account key BSX is not movement type dependent. Instead, BSX is dependent on the valuation class of the material, so it won't show in OMJJ.
thanks,

Jabber and O365 integration

Hello,
Do we need any additional licenses from Cisco or Microsoft to make a full possible integration between O365 and Jabber ?
For example features like :
Single Inbox Unified Messaging with SpeechView transcriptions, Microsoft Word Click to Call, SharePoint Presence & Click to Call, Jabber video calling and desktop sharing, and WebEx on desktop and iPad,
Thank you for your help
Best Regards,
Tomasz

Tomek,
There is no direct integration between Jabber and Office 365, except for Exchange Gateway integration on IMP server side which is not supported with Office 365. All other Jabber integrations do not go to Office 365, calendar client integrations are done with Outlook, and UM integration is between Office 365 and Unity Connection, which does not affect Jabber.
HTH,
Chris (Krzysiek) :-)

REPORT WITH SALES AND PRODUCTIN INTEGRATION?

HI,
HERE I NEED TO DISPLAY THE SALES AND PRODUCTION INTEGRATED (FOR MAKE TO STOCK) LIST BY DAY WISE ,I AM NOT ABLE TO FIND THE TABLES FOR THAT.
HERE LIST HEADER IS FOLOWING.
MATERIAL CODE, MATERIAL DISCRIPTION, PRODUCTION QTY, PROD. VALUE, SALES(BILLING QTY, SALES(BILLING) VALUE.
AND THAT LIST TOTAL PRODUCTION VALUE SHOULD EQUAL TO THAT PARTICULAR DAY TOTAL PRODUCTION VALUE,
AND THAT LIST TOTAL SALES(BLIING) VALUE SHOULD EQUAL TO THAT PARTICULSR DAY TOTAL SALES(BILLING) VALUE.
PLZ HELP OUT FROM THIS,
REWARDS IN ADVANCE....
REGARDS,
NAVEEN

Have you tried the txn code MC-Q or the report program RMCV0500.

Facebook and Twitter integration not working

I'm have trouble using Facebook and Twitter integration in Mountain Lion. When I click 'Click to Tweet', or 'Click to Post', nothing happens; I don't get the notecard looking thig, and it's like I never clicked the button. Same thing with sharing from an app, except for Twitter. I receive notifications from both just fine, but I'm unable to post. I can tweet something from the sharing menu (link to a webpage with Safari, for example), but I cannot send a tweet using the 'Click to Tweet' button in Notification Center. Also, I cannot post to Facebook by neither sharing nor the 'Click to Post' button. So far I have tried sharing with Safari, Finder, and Preview, all with the same results. (Facebook sharing with iPhoto does work, but I don't believe that is integrated with OS X.)
I have also tried the following, with no luck:
Checked my settings on the Facebook and Twitter sites.
Removed my acounts and re-added them.
Obviously, my internet connection is working.
Added my Facebook account to the 'Guest User' account, and another administrator account.
Had a friend add his Facebook account to his own (limited) account on my computer--he could not post to Facebook either.
I believe the last two things I tried indicate that this is a system-wide problem. A couple more things to note: 1) there is no kind of error message; it just sits there, like nothing happend, no 'spinning wheel' or anything. 2) It DID work before. Twitter worked when I first upgraded to Mountain Lion, and Facebook worked when I installed the 10.8.2 update. I don't use either often enough to know when exactly they stopped.
Here is a video illistrating my problem.
It's been driving myself crazy with this over the past few days, and can't seem to find an answer anywhere. I also seem to be the only one with this problem.

First, I would eject whatever it is that you downloaded. Go to Finder and eject it that way or depending how you have your system set up, do the two finger tap and Eject it. Download the link above. Once it downloads, double click it to install it. It should work. If it doesn't you need to use your Disk Utility to check for errors. Click your Finder again and then Applications. Scroll down to Utilities and then Disk Utility. Click on your hard drive and you will get a menu of items on the right side. Towards the bottom, you will see a button to Verify Disk Permissions. Click that and let it run. It may take a few minutes to finish. Once it's finished there may be a list of things wrong with your system. Click the Repair Permissions and let the computer do it's thing. Use Disk Utility at least once a month to make sure everything is in order on your system. If this doesn't fix it, I don't have any other suggestions. I'd hate to say do a fresh install but that might be the next step if this doesn't work.
Something else to consider is that is if you use Time Machine and the system did work at one point, you could go back to the last known good point and reinstall that back-up. You would lose anything you have saved since that point (obviously). If you take steps to back up your information, that should not be an issue. (For me), Time Machine works as advertised. If you are not backing system up regularly, shame on you. You need to start ASAP backing up. It's an easy process and it's times like you are having now, that make the small preventive maintenance, worth extra time and effort.
Good luck.

PS and PP integration

Dear Experts,
Good Morning....
Please suggest me PS and PP integration customization steps.
Regards
Lallan

PP is not a major player in PS as far as integration is concerned. It is through Material Management that Production Planning is informed of Production Orders using special settings in the Material Master.
One another area, the PP and PM modules share Work Centers with Project System.
The Work Center is needed for Capacity Planning and Planning costs. If we integrate this Work Center with HR module, we will be able to select only the people who have been assigned to the Work Center. We can specify the amount of work the individual will contribute. This forms the basis for capacity planning.
Hope u must have understand.
PS - Process
After creating the project next step is u want to do cost, Revenue & Budget Planning for the project
in the t-codes CJ42, CJ30 & CJ40 respectively. Next step is creating the Sale order in va01 T-code.
But I have internal project scenario, example: Overhauling of DG set. Assigned work enter & Workforce & also material to network. So shall I do costing? As explained! Is it necessary to create of Sales Order?
CMP2 - Assign workforce to activities
CAT2 - Transfer actual time to CATS. In CAT2 we have record the actual timing correct for an activity, on day basis & with personal number.
MD51 - Run Project MRP to create Planned orders.
MD04, ME21N, MIGO - Convert planned orders to purchase requisitions and P.O, and goods receipt.
MB1A - once the goods are brought is project stock; the same needs to be consumed by mb1a -281 Q on the project.
CJ20n - Attach milestones as per the payment terms.
VA02 - Copy billing plan to sales order.
VF01 - Billing
CJ20n - Project tech complete and closure.
Hope this will help you,
Regards,
ANSAR

SAP R/3 and BW integration Landscape

Hello Gurus,
Could you'll suggest a site or link where I could get a better insight into the SAP R/3 and BW integration Landscape, i.e. how Data gets transferred from SAP R/3 to BW.
Thanks,
Sebastian

Hi,
YOU can check the following for BW extraction
http://help.sap.com/bp_biv235/BI_EN/html/bw.htm
business content
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/biw/g-i/how%20to%20co-pa%20extraction%203.0x
https://websmp203.sap-ag.de/co
http://help.sap.com/saphelp_nw04/helpdata/en/37/5fb13cd0500255e10000000a114084/frameset.htm
PLease also have a look at BW data modelling guide,
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/5586d290-0201-0010-b19e-a8b8b91207b8
http://www.thespot4sap.com/Articles/SAP_BW_Metadata_Modelling.asp
Please reward points.

Brief discussion on SAP XI and its' Integration with SAP MDM.

Hi,
I have never worked on SAP XI.
I am discussing it on brief, please give your valuable replies.
SAP XI consists of System Landascape Directory(SLD).
SLD Consists of Business System and Techinical System.
Technical System contains all information about the software
component. The Business System consists of Inbound and Outbound Business
System which are used as logical names for data transfer.
There is communication Channel for Receiver and Sender Business System and n agreement
is signed between Sender and Receiver.
Outbound Interface defined for Business System Outbound and Techical System associated
with the Business System,
Inbound Interface defined for Business System Inbound and Techical System associated
with the Business System.
In SAP NetWeaver XI Integration Directory, we have defined the Integration Scenarios,
Actions, Interface Objects, Mapping Objects, Adapters Objects.
Mapping Object defines the Structure and Value Mapping.
Adapter Objects defines the Adapter program which implements RFC Adapter, FTP Adapter logic.
FTP Adapter is used for XI-MDM Communication.
RFC Adapter is used for XI-ECC Communication.
Integration Repository: Both Outbound and Inbound Interfaces are Mapped with Value mapping and
Structure Mapping inside Integration Repository.
The File Adapter takes the File from the Outbound port of MDM System
and sends it as IDOC to Receiver Business System.
Value Mapping must be done between Sender and Receiver interfaces.
Value Mapping is done by XSLT or Java based program.
SAP NetWeaver XI Integration Server at runtime:
Message Split, Interface Determination, Receiver Identifaction, Mapping, Techincal Routing
and Call Adapter Proccess are done.
In SAP XI 3.0 and MDM 5.5:
Step 1: Create busines system as service.
Step 2: Create communication channel for each business service. If the system can communicate
through different channels, then create all possible channel types if necessary.
Step 3: Create receiver agreement between the systems.
Step 4: Interface determination:
- Here you see for the first time the software component mentioned;
there are some special requirements regarding this software component in relation to the customizing ID mapping.
- To modify this software component, the customer needs to copy the SAP standard delivered software component
into its own namespace. The customer is able to modify to create archives
for the customized ID mapping.
Receiver determination.
Configure an FTP Server on the MDS.
Create a send folder for outbound messages using outbound port(s) for
remote systems(s).
Create receive folder inbound messages using inbound port(s) for remote systems.
This ia all about concept of SAP XI Infractsture and its' Integration with SAP MDM 5.5.
Regards
Kaushik Banerjee

Hi Kaushik,
You must be aware of File types that MDM Import Manager can Import i.e. we have XML, Excel etc. Now there are two transactions to extract data from R3
1. MDMGX -
         - For lookup table extraction
         - Output in XML format which MDM can import without using XI.
          - FTP can be configured to put the file in the desired folder which will be then picked by Import Server.
2. MDM_CLNT_EXTR -
          - For Main table records.
          - Output is in Idoc format which MDM doesn't understand hence we need XI in between which converts Idoc file received from R3 into XML which can then be imported using Import Manager or Import Server. For this we need to implement XI Scenario that consists of Source System, Receiver System, Type of Data etc.
Just a basic understanding...
Regards,
Jitesh Talreja

Business Object and SAP Integration

All,
We've BOJ Data Services XI installed.
Would like to integrate with SAP, does anyone know how or have good information about Business Object and SAP Integration?
Please adivce.

Hi Lynn,
If you need to have Business Objects and SAP work together in conjunction you need to have the Business Objects Integration Kit for SAP. Integration Kit provides the database drivers and other features for reporting off SAP.
Link to download the useru2019s Guide:
- Please go to Http://help.sap.com
- Click on Business Objects tab
- Select the product as Integration Kit for SAP
User guide: Business Objects Integration Kit for SAP Useru2019s Guide.
I hope that helps you.
Regards,
Prashant

CCM and CME integration, SIP

Similar Messages

Maybe you are looking for