SNMP information from Cisco 2800 ISRs

I have several 2800 series routers setup as MGCP gateways with T1 PRI connections to the PSTN. Does anyone know what MIBs/OIDs to monitor for individual DS0 and DS1 activity? I opened a TAC case, but it wasn't very fruitful. Basically I just want to know how many active calls per PRI, averages, totals, uptime, etc.

Hi, the MIB would be is this:
ftp://ftp.cisco.com/pub/mibs/v2/ISDN-MIB.my
hope this helps, please rate post if it does!

Similar Messages

  • Collecting information from Cisco switchs using SNMP

    Dear All,
    I have a wide network with more than 250 sites connected using the DSL. the WAN devices are under the provider responsability and the LAN devices are directly in my responsability. In each site, I have :
    1 or 2 Cisco switchs (2960 or 3560), connecting via fibr.
    or
    Linksys switch connected via ethernet cable
    and
    cisco 877 router connected to switch
    cisco 881G router conected to switch
    pc and printers
    In order to improve the availibilty of our network, we lauch every day a script from local pc to test connectivity of LAN equipements :
    ping to switchs (Vlan 1), ping to ip fa0/0 cisco router1, ip cisco router2, ping to HSRP address (of two router). the resulting ini file will be inserted in a database and exported to excel for analysing.
    I'm asking if someone can help in order to implement SNMP and let me know the name of cisco MIB to implement to :
    - to have from SNMP information, the result of show cdp nei, show interface status, show ip int brief,...
    - to have if wan router LAN interface are up,connected
    -  others usefuls informations.
    Thanks and regards,
    AA

    Hi,
    the basic SNMP config for 2960 and 3560 is:
         snmp-server community <> RO
    The configuration for SNMP traps to get alerts from the device if there is for example a failure with a fan is:
              snmp-server enable traps
              snmp-server host <> <>
    This enables all traps available with your IOS version. You can the disable not wanted traps by using the "no"-command like this.
    Example for dot1x traps:
              no snmp-server enable traps dot1x
    With a snmp client you can then do a snmpwalk (or snmp get) without a specific OID to get all the SNMP information from the device:
    On a Linux server the following command should work:
         snmpwalk -v 2c -c <> -T <>
    -v = use SNMP version 2c
    -c = use the community string you configured on the device
    -T = output in the dotted decimal format
    But be careful, this will be a lot of data output.
    Here you will find a docu for configuring SNMP on a Cisco device:
    http://www.cisco.com/en/US/docs/ios/12_2/configfun/configuration/guide/fcf014.html
    Sven

  • MPLS CE support on Cisco 2800 ISR router

    Hi all, could I ask you for some hints about MPLS CE support on Cisco 2800 ISR router today? I`m finding restrictions and recommendations for feature implementation. Do you have any cisco web site about them?
    Thank you for your advice and/or hints.
    Peter

    Thanks for an answer. I need to use multi-VPN model on CE router, but with QoS on one physical CE-PE connection (e.g. Frame-Relay DLCI).However, all VPNs on CE router must be secured for each one. The solution is Multi-VRF service feature, but, however, with multi-DLCI model on Frame-Relay and QoS per DLCI. Now, I`m finding a scenario to provide multi-VPN model on CE router with single-DLCI model and single QoS per one DLCI for all VPNs. And that, MPLS CE feature on C2800 could be used, if possible.
    So, I don`t know more about MPLS CE on C2800 and I don`t know make a result to propsed solution...

  • SNMP traps from Cisco 4404

    I have a Cisco 4404 WLC that sends its system logs to a syslog server (kiwicat), but I'm interested in getting the snmp traps sent over there as well.  I've configured the syslog server to accept the snmp on the right ports and I've confirmed that the syslog server can receive then by sending traps manually from other devices.
    I cannot seem to actually get the WLC to send the traps to the server.  the syslog stuff gets through ok, but not the snmp.  I've added the syslog server as an SNMP trap reciever and configured it as much as it needs to be and the only difference it seems to have made is to add more things to the main trap log on the 'monitor' tab on the WLC.  Am i missing something really basic?
    p.s. the WLC and the syslog server are separated by a firewall, but the syslog rules have been altered to also allow the snmp, should it attempt to go through.
    Any help would be gratefully received.

    Yes, I think the Network Devices need to be discovered first in order to receive traps and generate alerts.
    Juke Chou
    TechNet Community Support

  • Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

    Hello,
    Currently Running:
    Cisco Unified Communications Manager 8.6.2
    Cisco Unity Connection 8.6.2
    Problem:
    when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
    example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
    we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
    I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
    upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
    I also have the message relaying to my E-mail and I get the same in the subject line.
    "Message from Cisco Unity Connection Messaging System (Unknown extension)"
    This tends to be a big deal with the Sales team as customers will call and say "Call me back"
    But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
    Any help will be appreciated.
    Thanks
    Tim

    Found another post that referenced Cisco Bug ID CSCti37610.
    CUC plays message is from Unity Connection Messaging system
    Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
    Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
    Workaround:
    Restart the Unity Connection servers
    It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

  • Curious message during activation of snmp traps in cisco router 2800

    I activated snmp traps in cisco router 2800 (I didn't specify a set of them, so all of them were activated). The thing is, when i configure "snmp-server enable traps", appears a message in the next line :
    " %Cannot enable both sham-link state-change interface traps.
       %New sham link interface trap not enabled "
    Anyway, traps are activated and are completely functional.
    I would like to know, why this message appears... and also what is the difference between  informs and traps, because I can activate both of the in a router to be sent to the network admin pc.
    Thanks in advance.

    Hi Marcelo,
    the snmp-server enable traps command enables just all types of traps that the IOS version supports.
    The message apperes because of this two, which are mutually exclusive:
    R1(config)#snmp-server enable traps ospf cisco-specific state-change shamlink interfaceR1(config)#snmp-server enable traps ospf cisco-specific state-change shamlink interface-old% Cannot enable both sham-link state-change interface traps.% Deprecated sham link interface trap not enabled.
    It's recommended to only enable the traps you really need.
    Informs were introduced with SNMPv2, and they have the same format and purpose as traps.
    The main difference is that traps are send in a hit-or-miss fashion whereas informs expect an acknowledge and will be re-send if unacknowledged.
    Hope that helps
    Rolf

  • How can I get CDP neighbor information from access point reports in Cisco Prime 2.0

    How can I get CDP neighbor information from access point reports in Cisco Prime 2.0?  I have looked through all the reports and I cannot find a report that gives me the CDP neighbor information of an access point.  I thought that information was in there, however I cannot seem to find it.
    Thanks in advance!

    Hi
    You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.
    Regards
    Rasika
    **** Pls rate all useful responses ****

  • I can't retrieve usm and vacm tables from router cisco 2800. Help please!!

    Hi, I'm doing some tests in a router cisco 2800 using snmp in versions 2c and 3. I configured views and communities for version 2c and user, groups and views for version3; I suppose that the vacm and usm parameters involved in the groups, views are stored internally in usm, vacm tables. I wanted to check if the parameters I configured were inside the tables, but when I tried to retrieve all those values through get table or get next commands, I obtained the answer "end of mib view" in the application I'm using (SNMP J MANAGER) and also in wireshark where the requests are sent but the responses contain the OIDs belonging to  the tables but with the value end of mib view.
    I know for experience doing the tests, that "end of mib view" is obtained in a response when you try to request a OID that is outside of the view being used by a community. But the last thing I did was create a community related to a view with access to internet included. Later, I used that community (comlectura) in version 2c to retrieve those values of usmtable (1.3.6.1.6.3.15.1.2.2 ) and vacmtable (inside of 1.3.6.1.6.3.16.1) and nothing.
    These are some commands I configured in the router:
    snmp-server group readonly v3 auth read readview
    snmp-server group writeonly v3 auth write writeview
    snmp-server view readview internet included
    snmp-server view writeview internet included
    snmp-server view viewcomlectura mib-2 included
    snmp-server view viewcomlectura2 system included
    snmp-server community comlectura view readview RO
    snmp-server community comlectura2 view viewcomlectura2 RO
    snmp-server trap-source FastEthernet0/1
    I think the cause of this error perhaps is because these tables don't exist in the CISCO MIB, but I don't thinks cisco devices ONLY have cisco mibs (
    1.3.6.1.4.1.9) inside of them, because I can make request with OIDs of mib-2 branches. Anyway, please someone that can guide me in this problem. Thanks in advance.

    You cannot use Mavericks. Ask a friend who still runs windows or any Mac OS except Mavericks to bring their laptop and help you out.
    Or plug in a USB drive for instance and create a bootable version of any previous version of OSX since 10.5.x -10.8 all of which will work fine.
    Or dual boot to windows where the latest airport utility is still 5.6

  • Migrating from Brocade 2800/ 3900 to Cisco MDS 9509

    What is the best procedure from migrating from Brocade 2800/3900/12000 to Cisco MDS 9509 especially connected to HP-UX and AIX server.
    Without any Downtime I should be able to migrate these servers.
    I thought about these options:
    1. Use vgexport and vgimport or exportvg and importvg (AIX) after connecting to Cisco MDS. But this requires complete downtime on the application.
    2. Take one path down or HBA down and switch the cable and vgextend the devices.
    Please let me know if somebody has procedure.
    I was successful in HP-UX server using the second options but I cant see all the LUNs. That might be array specific problem also.
    If anybody has detailed procedure on migrating this scenario. please let me know.
    We are using Persistent FCIDs on our MDS switches.
    Thanks in Advance

    After connecting 1 cable from server HBA to Cisco S/w, why you are not able to see all LUNs, did you cross-check that...I mean HBA Configuration (max 256 LUNs) or Disk Array library driver to be installed on host side.if that can be sorted out, you can mirror the volumes across the disk arrays.are you using HDS Arrays? I don't know but what is vgextend command you are mentioning...
    also did you take a reboot of server or is it online addition on new LUNs...
    Also any how if you are not able to see all LUNs that is going to be an issue later as well for migration...pls cross-check that...

  • Cisco 881 ISR IPSec VPN Tunnel does not pass traffic from the vlan.

    I have a cisco 881 ISR Router with a site-to-site IPsec vpn tunnel to a mikrotik device on the other end (I inherited this from my client). The tunnel is constructed properly and is up, however traffic does not pass or get routed to the FA4 interface. I see in my packet captures that it hits the vlan1 interface (vlans are required on the L2 ports) and does not pass to the tunnel.
    This is my configuration:
    141Kerioth#sh config
    Using 3763 out of 262136 bytes
    ! Last configuration change at 01:02:41 UTC Mon May 26 2014 by admin
    version 15.2
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname 141Kerioth
    boot-start-marker
    boot-end-marker
    logging buffered 51200 warnings
    aaa new-model
    141Kerioth#do wr mem
                  ^
    % Invalid input detected at '^' marker.
    141Kerioth#wr mem
    Building configuration...
    [OK]
    141Kerioth#sh run
    Building configuration...
    Current configuration : 5053 bytes
    ! Last configuration change at 01:38:06 UTC Mon May 26 2014 by admin
    version 15.2
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname 141Kerioth
    boot-start-marker
    boot-end-marker
    logging buffered 51200 warnings
    aaa new-model
    aaa authentication login default local
    aaa authentication ppp default local
    aaa session-id common
    memory-size iomem 10
    crypto pki trustpoint TP-self-signed-580381394
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-580381394
     revocation-check none
     rsakeypair TP-self-signed-580381394
    crypto pki certificate chain TP-self-signed-580381394
     certificate self-signed 01
      30820229 30820192 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
      30312E30 2C060355 04031325 494F532D 53656C66 2D536967 6E65642D 43657274
      69666963 6174652D 35383033 38313339 34301E17 0D313430 35323231 38323333
      365A170D 32303031 30313030 30303030 5A303031 2E302C06 03550403 1325494F
      532D5365 6C662D53 69676E65 642D4365 72746966 69636174 652D3538 30333831
      33393430 819F300D 06092A86 4886F70D 01010105 0003818D 00308189 02818100
      B001A012 2CA6970C 0648798B 2A786704 84F2D989 83974B19 9B4287F2 4503D2C9
      173F23C4 FF34D160 202A7565 4A1CE08B 60B3ADAE 6E19EE6E 9CD39E72 71F9650E
      930F22FE C4441F9C 2D7DD420 71F75DFC 3CCAC94E BA304685 E0E62658 A3E8D01C
      D01D7D6A 5AF0B0E6 3CF6AF3A B7E51F83 9BF6D38E 65254E1F 71369718 ADADD691
      02030100 01A35330 51300F06 03551D13 0101FF04 05300301 01FF301F 0603551D
      23041830 168014D6 24878F12 1FFADF2F 537A438E 6DD7FB6B D79E4130 1D060355
      1D0E0416 0414D624 878F121F FADF2F53 7A438E6D D7FB6BD7 9E41300D 06092A86
      4886F70D 01010505 00038181 00771667 FCA66002 8AB9E5FB F210012F C50B586F
      9A9640BB 45B4CEFD 030A38C0 E610AAC8 B41EF3C4 E55810F9 B2C727CF C1DEFCF1
      0846E7BC 1D95420E 5DADB5F8 EFE7EB37 B5433B80 4FF787D4 B1F2A527 06F065A4
      00522E97 A9D2335C E83C4AE1 E68D7A41 9D0046A7 ADCC282B 7527F84D E71CC567
      14EF37EA 15E57AD0 3C5D01F3 EF
            quit
    ip dhcp excluded-address 10.0.16.1
    ip dhcp pool ccp-pool
     import all
     network 10.0.16.0 255.255.255.0
     default-router 10.0.16.1
     dns-server 8.8.8.8
     lease 0 2
    ip domain name kerioth.com
    ip host hostname.domain z.z.z.z
    ip name-server 8.8.8.8
    ip name-server 4.2.2.2
    ip cef
    no ipv6 cef
    license udi pid CISCO881-K9 sn FTX180483DD
    username admin privilege 15 secret 4 CmmfIy.RPySmo4Q2gEIZ2jlr3J.bTBAszoe5Bry0z4c
    username meadowbrook privilege 0 password 0 $8UBr#Ux
    username meadowbrook autocommand exit
    policy-map type inspect outbound-policy
    crypto isakmp policy 1
     encr 3des
     authentication pre-share
     group 5
    crypto isakmp key 141Township address z.z.z.z
    crypto isakmp keepalive 10
    crypto ipsec transform-set TS esp-3des esp-sha-hmac
     mode tunnel
    crypto map mymap 10 ipsec-isakmp
     set peer z.z.z.z
     set transform-set TS
     match address 115
    interface Loopback0
     no ip address
    interface Tunnel1
     no ip address
    interface FastEthernet0
     no ip address
    interface FastEthernet1
     no ip address
    interface FastEthernet2
     no ip address
    interface FastEthernet3
     no ip address
    interface FastEthernet4
     description $FW_OUTSIDE_WAN$
     ip address 50.y.y.y 255.255.255.240
     ip nat outside
     ip virtual-reassembly in
     duplex auto
     speed auto
     crypto map mymap
    interface Vlan1
     description $ETH_LAN$
     ip address 10.0.16.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly in
     ip tcp adjust-mss 1452
    ip forward-protocol nd
    ip http server
    ip http access-class 23
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip nat inside source list 115 interface Vlan1 overload
    ip nat inside source list 199 interface FastEthernet4 overload
    ip nat inside source route-map nonat interface FastEthernet4 overload
    ip route 0.0.0.0 0.0.0.0 50.x.x.x
    access-list 110 deny   ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
    access-list 110 permit ip 10.0.16.0 0.0.0.255 any
    access-list 115 permit ip 10.0.16.0 0.0.0.255 10.0.1.0 0.0.0.255
    access-list 144 permit icmp host c.c.c.c host 10.0.1.50
    access-list 144 permit icmp host p.p.p.p host 10.0.16.105
    access-list 199 permit ip a.a.a.a 0.0.0.255 any
    no cdp run
    route-map nonat permit 10
     match ip address 100
    line con 0
     no modem enable
    line aux 0
    line vty 0 4
     access-class 1 in
     exec-timeout 30 0
     privilege level 15
     transport preferred ssh
     transport input ssh
    line vty 5 15
     access-class 23 in
     privilege level 15
     transport input telnet ssh
    cns trusted-server all-agents x.x.x.x
    cns trusted-server all-agents hostname
    cns trusted-server all-agents hostname.domain
    cns id hardware-serial
    cns id hardware-serial event
    cns id hardware-serial image
    cns event hostname.domain 11011
    cns config initial hostname.domain 80
    cns config partial hostname.domain 80
    cns exec 80
    end

    Why do you have following command on the PIX?
    crypto map outside_map 40 set transform-set 165.228.x.x
    Also you have this transform set on the PIX:
    crypto ipsec transform-set 10.112.60.0 esp-aes-256 esp-sha-hmac
    This does not match the transfor set on the router:
    crypto ipsec transform-set tritest esp-3des esp-md5-hmac
    Where are you using the access-list/route-map
    101 ?

  • What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

    Hi Cisco Community / Friends,
    I am new to this site though I have cisco account for many years. I am a CCNA ,I  passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
    We have a new project for the VSAT Comm'n of  Coast Watch Station ,  The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of  subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site  are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for? 
    Appreciate your comments and help on this matter.. Thank You very much
    Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
    (Errors see below)
    CWS_4_Pandami(config-erm)#mmi polling-interval 60
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#no mmi auto-configure
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#no mmi pvc
                                                           ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                            ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
    CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
    CWS_4_Pandami(config-if)# bandwidth 256
    CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
    CWS_4_Pandami(config-if)# duplex auto
    CWS_4_Pandami(config-if)# speed auto
    CWS_4_Pandami(config-if)# priority-group 1
                                                        ^
    % Invalid input detected at '^' marker.
    CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
    CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                                                    ^
    % Invalid input detected at '^' marker.

    Hi
    From Cisco's website:
    The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
    The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
    So because this is your device, you don't want to use MMI anyways.
    And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

  • Prime Infrastructure 2.1 - getting informations from Nexus7Ks about ip to mac to physical pot table

    Hello,
    does anybody know if there's a way to get the following informations out of nexus 7000 and nexus 5000/2000 switches?
    Environment/requirements:
    - snmp v3 has to be used
    - N7ks are configured with several vrfs
    - SW N7K: 6.2.8a
    - SW N5K: 6.0(2)N2(4)
    - Prime Infrastructure 2.1
    I want to see under Clients and Users entries about mac-address, ip-address, interface and vlan.
    At the moment, I only get informations from N5Ks/N2Ks without ip-addresses. From the N7ks I don't get any informations.
    Any hints or tricks, how to get these informations with PI2.1 out of the nexus boxes?
    best regards
    Markus

    Hi Andy,
    Check the below link , as per this Doc .. User tracking is supported in 2.0:
    http://www.cisco.com/en/US/prod/collateral/netmgtsw/ps6504/ps6528/ps12239/guide_c07-729089.html
    Thanks-
    Afroz
    [Do rate the usefu post]

  • Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

    Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
    and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
    My questions are How do you direct this utility to point to the desktop or the TFTP folder
    does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
    My router is suppose to have 10.0.0.3 255.0.0.0
    Gateway of 10.0.0.1 255.0.0.0
    My TFTP Server 10.0.0.2 255.0.0.0
    How do I get the MAC address of the Router or the TFTP Server and which one  is required?
    my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
    =====================================================================================
    rommon 10 >
    rommon 10 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    ?=0
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=
    rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    rommon 12 > TFTP_CHECKSUM=0
    rommon 13 > SET
    monitor: command "SET" not found
    rommon 14 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    ?=0
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    rommon 15 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 16 >       " not found
    rommon 17 >FE_SPEED_MODE=2
    variable name contains illegal (non-printable) characters
    rommon
    rommon 18 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    ?=0
    rommon 19 > tftpdnld [ur]
    usage: tftpdnld [-hr]
      Use this command for disaster recovery only to recover an image via TFTP.
      Monitor variables are used to set up parameters for the transfer.
      (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
      "ctrl-c" or "break" stops the transfer before flash erase begins.
      The following variables are REQUIRED to be set for tftpdnld:
                IP_ADDRESS: The IP address for this unit
            IP_SUBNET_MASK: The subnet mask for this unit
           DEFAULT_GATEWAY: The default gateway for this unit
               TFTP_SERVER: The IP address of the server to fetch from
                 TFTP_FILE: The filename to fetch
      The following variables are OPTIONAL:
              TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
          TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
              TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
             TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
              TFTP_MACADDR: The MAC address for this unit
                   FE_PORT: 0= (default), 1
             FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                            5=Auto (default)
          TFTP_DESTINATION: The flash destination device for the file
                            flash:(default), usbflash0:, usbflash1:
      Command line options:
       -h: this help screen
       -r: do not write flash, load to DRAM only and launch image
    rommon 20 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 21 >

    What I notice in the original post is this error
    ARP: address resolution for 10.0.0.2 timed out.
    which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
    HTH
    Rick

  • How Do I Configure A WRT54G to Work With A Cisco 2800 Router

    I'm helping my dad set up a new network.  He has a Cisco 2800 series router that connects to the internet via two T1 lines.  From this connection, he supplies internet service to his customers.  The router was installed and configured with help from AT&T who monitors the router and advises my dad if there are problems. 
    The Cisco 2800 is not my reason for posting.
    He wants to connect his home computers to the 2800.  He has one desktop and two wireless laptops and wants to use a WRT54G to connect those computers to the 2800 router.  How should he configure the WRT54G to connect to the 2800?  
    Thanks!

    That's what I thought.  So it is really no different than connecting the WRT to a DSL modem or cable modem as far as the setup goes. Good then.
    Now, next question;
    Would this network setup be correct?
    Connect a 5-port switch to the 2800
    Connect the WRT54G to the 5-port switch.
    Configure the laptops to connect throught the WRT54G.
    Connect the desktop (Ubuntu 9.10) to the 5-port switch via Ethernet cable (bypass the WRT54G).
    Would there be IP conflicts or domain problems?  I ask this because this is how his LAN is presently setup and he seems to be getting random connectivity problems on his Ubuntu desktop machine.  One day it works fine.  The next day it won't connect.  Sometimes, even after he is connected, it stop works midstream.  It also takes 10 minutes or so to boot up.  The laptops always work without issue.
    The two laptops would be issued IP addresses of 192.168.1.xxx but the desktop would be getting 12.83.xxxx.xx(something similar).  The desktop's internet IP would receive its internet IP from the 2800 via DHCP just like the WRT54G is receiving its IP from the 2800.  The two would essentially be on different LANs connected to the same router.  Do you forsee any issues here?
    Thanks!

  • What I would like from Cisco is the meaning of all level 3 or lower email messages my Router can send to me. So, that I can take the appropriate actions.

    v\:* {behavior:url(#default#VML);}
    o\:* {behavior:url(#default#VML);}
    w\:* {behavior:url(#default#VML);}
    .shape {behavior:url(#default#VML);}
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0in 5.4pt 0in 5.4pt;
    mso-para-margin-top:0in;
    mso-para-margin-right:0in;
    mso-para-margin-bottom:10.0pt;
    mso-para-margin-left:0in;
    line-height:115%;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;
    mso-bidi-font-family:"Times New Roman";
    mso-bidi-theme-font:minor-bidi;}
    My Small Business Router has been sending me email messages. This is a RVS-4000 version 1.
    I just want to understand what my Router is emailing me or telling me...
    The last message I received from my RVS-4000 was:
       Oct 30 13:44:09 - IPSEC EVENT: KLIPS device ipsec0 shut down.
    IPSEC EVENT sounds important. Whatever it is... And what is a KLIPS device ipsec0 shutdown????
    I have Log Levels 0-3 selected...
    Log Level
    Setting which level log Router should recorder. Level from 0 ~ 7 means:
    0: LOG_EMERG(system is unusable)
    1: LOG_ALERT(action must be taken immediately)
    2: LOG_CRIT(critical conditions)
    3: LOG_ERR(error conditions)
    4: LOG_WARNING(warning conditions)
    5: LOG_NOTICE(normal, but significant, condition)
    6: LOG_INFO(informational message)
    7: LOG_DEBUG(debug-level message)
    So, when I get any messages... I'm a little concerned. Because the RVS-4000 thinks it's an Error or better.
    What I would like from Cisco is the meaning of all level 3 or lower email messages my Router can send to me. So, that I can take the appropriate actions.
    I know Cisco inhered these Small Business Routers. When they bought Linksys. However, they have not discontinued them totally and they are still for sale. And Cisco has released a new version 2 of the same Router. So I believe Cisco should support them as well.
    Yes, I'm a pain to Cisco. However, I think you understand I'm being scared by my Routers messages to me... And would like some relief.
    Bruce

    Great suggestions. Problems is this is not the forum for your "wish list" as Apple does not read these USER forums.
    Send your feedback to http://www.apple.com/feedback/iphone.html

Maybe you are looking for