Cisco 857w PPTP client?

Hello,
Looks like cisco 857w does not support pptp client in my IOS version, only l2tp is supported. Does there is some IOS version I can upgrade/downgrade to configure cisco as pptp client?

None of Cisco devices can be configured as PPTP client. Cisco devices can only be configured as PPTP server.

Similar Messages

Cisco 1841 as PPTP client Does not work

Dear All,
I have Cisco 1841 router running the below roles
1) SSL VPN Server
2) PPTP Server
3) Site to Site Connection with Sonicwall router
I want the router to be configured a pptp client to internet vpn server (so that i will get a fixed public ip )
Once i get this ip address i want to use this connection to accept in coming connection and forward ports to internal host,
I went through below
http://www.mreji.eu/content/cisco-router-pptp-client
https://supportforums.cisco.com/thread/2167562
But it does not work as i do not have the option for the below 2 commands in vpdn-group 2 section.(Please see section in blue)
protocol pptp
rotary-group 4
Please Advise and Help
Regards
Hasan Reza
My Current Config is as below
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.09 17:55:23 =~=~=~=~=~=~=~=~=~=~=~=
exit
Gateway#show run |
Building configuration...
Current configuration : 25109 bytes
! Last configuration change at 13:33:57 UTC Sun Jun 9 2013 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Gateway
boot-start-marker
boot system flash c1841-advsecurityk9-mz.151-2.T1.bin
boot-end-marker
logging buffered 4096
no logging console
enable secret 5 $1$SciF$TlX1tR5qaG9ZE7pdZHcRJ/
no aaa new-model
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 10.236.5.1 10.236.5.20
ip dhcp excluded-address 10.236.5.21 10.236.5.50
ip dhcp excluded-address 172.21.51.2 172.21.51.50
ip dhcp pool ContosoPool
   network 10.236.5.0 255.255.255.0
   default-router 10.236.5.254
   dns-server 213.42.20.20 195.229.241.222
ip dhcp pool DMZ
   network 172.21.51.0 255.255.255.0
   dns-server 172.21.51.10
   default-router 172.21.51.1
   domain-name contoso.local
ip cef
ip domain name contoso.local
ip name-server 213.42.20.20
ip name-server 195.229.241.22
ip name-server 195.229.241.222
ip ddns update method dyndns
HTTP
add http://xxxxxx:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://xxxxxx:yyyyy@@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 0 1 0 0
multilink bundle-name authenticated
vpdn enable
vpdn-group 2
request-dialin
protocol l2tp
initiate-to ip 173.195.0.42
vpdn-group RAS-VPN
! Default PPTP VPDN group
accept-dialin
protocol pptp
virtual-template 1
l2tp tunnel timeout no-session 15
crypto pki token default removal timeout 0
crypto pki trustpoint TP.StartSSL.CA
enrollment terminal pem
revocation-check none
crypto pki trustpoint TP.StartSSL-vpn
enrollment terminal pem
usage ssl-server
serial-number none
fqdn ssl.spktelecom.com
ip-address none
revocation-check crl
rsakeypair RSA.StartSSL-vpn
crypto pki trustpoint TP-self-signed-1981248591
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1981248591
revocation-check none
rsakeypair TP-self-signed-1981248591
crypto pki trustpoint VMWare
enrollment terminal
revocation-check crl
crypto pki trustpoint OWA
enrollment terminal pem
revocation-check crl
crypto pki certificate chain TP.StartSSL.CA
certificate ca 01
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP.StartSSL-vpn
certificate 0936E1
    (removed the certificate info for clarity)9
   quit
certificate ca 18
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP-self-signed-1981248591
certificate self-signed 01
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain VMWare
certificate ca 008EDCE6DBCE6B
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain OWA
   (removed the certificate info for clarity)
license udi pid CISCO1841 sn FCZ122191TW
archive
log config
hidekeys
username admin privilege 15 password 7 1304131F02023B7B7977
username ali password 7 06070328
redundancy
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
lifetime 84000
crypto isakmp key admin_123 address 0.0.0.0 0.0.0.0
crypto isakmp keepalive 10
crypto ipsec security-association lifetime seconds 28800
crypto ipsec transform-set vpnset esp-3des esp-sha-hmac
crypto ipsec transform-set strongsha esp-3des esp-sha-hmac
crypto dynamic-map mydyn 10
set transform-set strongsha
crypto map Dxb-Auh 1000 ipsec-isakmp dynamic XXXXXXXXXX
interface FastEthernet0/0
description Internal Network (Protected Interface)
ip address 10.236.5.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
shutdown
no atm ilmi-keepalive
interface BRI0/1/0
no ip address
encapsulation hdlc
shutdown
interface Virtual-Template1
ip unnumbered Dialer1
peer default ip address dhcp-pool ContosoPool
ppp encrypt mppe auto required
ppp authentication ms-chap ms-chap-v2 eap
interface Dialer1
ip ddns update hostname XXXXXXX.dyndns.org
ip ddns update dyndns
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1450
dialer pool 1
ppp pap sent-username vermam password 7 13044E155E0913323B
crypto map Dxb-Auh
interface Dialer2
mtu 1460
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 2
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap ms-chap-v2 callin
ppp eap refuse
ppp chap hostname hasanreza
ppp chap password 7 070E2541470726544541
interface Dialer995
no ip address
ip local pool webssl 10.236.6.10 10.236.6.30
ip forward-protocol nd
ip http server
ip http secure-server
ip nat inside source list nat interface Dialer1 overload
ip nat inside source static tcp 10.236.5.12 25 interface Dialer1 25
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 172.21.51.0 255.255.255.0 10.236.5.253
ip access-list extended internal
permit ip any 10.236.5.0 0.0.0.255
ip access-list extended nat
deny   ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
deny   ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 any
ip access-list extended nonat
permit ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
ip access-list extended sslacl
ip access-list extended webvpn
permit tcp any any eq 443
logging esm config
access-list 101 permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
line vty 5 15
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
scheduler allocate 20000 1000
webvpn gateway gateway1
ip interface Dialer1 port 443
ssl encryption rc4-md5
ssl trustpoint TP.StartSSL-vpn
inservice
webvpn install svc flash:/webvpn/anyconnect-win-3.1.00495-k9.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context webvpn
ssl authenticate verify all
url-list "Webservers"
   heading "SimpleIT Technologies NBNS Servers"
   url-text "Google" url-value "www.google.com"
   url-text "Mainframe" url-value "10.236.5.2"
   url-text "Mainframe2" url-value "https://10.236.5.2"
nbns-list "ContosoServer"
   nbns-server 10.236.5.10
   nbns-server 10.236.5.11
   nbns-server 10.236.5.12
port-forward "PortForwarding"
   local-port 3389 remote-server "10.236.5.10" remote-port 3389 description "Server-DC01"
policy group policy1
   url-list "Webservers"
   port-forward "PortForwarding"
   nbns-list "ContosoServer"
   functions file-access
   functions file-browse
   functions file-entry
   functions svc-enabled
   svc address-pool "webssl"
   svc default-domain "Contoso.Local"
   svc keep-client-installed
   svc split include 10.236.5.0 255.255.255.0
   svc split include 10.236.6.0 255.255.255.0
   svc split include 172.31.1.0 255.255.255.0
   svc split include 172.21.51.0 255.255.255.0
   svc dns-server primary 172.21.51.10
default-group-policy policy1
gateway gateway1
inservice
end
Gateway#

Dear All,
I have Cisco 1841 router running the below roles
1) SSL VPN Server
2) PPTP Server
3) Site to Site Connection with Sonicwall router
I want the router to be configured a pptp client to internet vpn server (so that i will get a fixed public ip )
Once i get this ip address i want to use this connection to accept in coming connection and forward ports to internal host,
I went through below
http://www.mreji.eu/content/cisco-router-pptp-client
https://supportforums.cisco.com/thread/2167562
But it does not work as i do not have the option for the below 2 commands in vpdn-group 2 section.(Please see section in blue)
protocol pptp
rotary-group 4
Please Advise and Help
Regards
Hasan Reza
My Current Config is as below
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.06.09 17:55:23 =~=~=~=~=~=~=~=~=~=~=~=
exit
Gateway#show run |
Building configuration...
Current configuration : 25109 bytes
! Last configuration change at 13:33:57 UTC Sun Jun 9 2013 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Gateway
boot-start-marker
boot system flash c1841-advsecurityk9-mz.151-2.T1.bin
boot-end-marker
logging buffered 4096
no logging console
enable secret 5 $1$SciF$TlX1tR5qaG9ZE7pdZHcRJ/
no aaa new-model
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 10.236.5.1 10.236.5.20
ip dhcp excluded-address 10.236.5.21 10.236.5.50
ip dhcp excluded-address 172.21.51.2 172.21.51.50
ip dhcp pool ContosoPool
   network 10.236.5.0 255.255.255.0
   default-router 10.236.5.254
   dns-server 213.42.20.20 195.229.241.222
ip dhcp pool DMZ
   network 172.21.51.0 255.255.255.0
   dns-server 172.21.51.10
   default-router 172.21.51.1
   domain-name contoso.local
ip cef
ip domain name contoso.local
ip name-server 213.42.20.20
ip name-server 195.229.241.22
ip name-server 195.229.241.222
ip ddns update method dyndns
HTTP
add http://xxxxxx:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://xxxxxx:yyyyy@@members.dyndns.org/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 0 1 0 0
multilink bundle-name authenticated
vpdn enable
vpdn-group 2
request-dialin
protocol l2tp
initiate-to ip 173.195.0.42
vpdn-group RAS-VPN
! Default PPTP VPDN group
accept-dialin
protocol pptp
virtual-template 1
l2tp tunnel timeout no-session 15
crypto pki token default removal timeout 0
crypto pki trustpoint TP.StartSSL.CA
enrollment terminal pem
revocation-check none
crypto pki trustpoint TP.StartSSL-vpn
enrollment terminal pem
usage ssl-server
serial-number none
fqdn ssl.spktelecom.com
ip-address none
revocation-check crl
rsakeypair RSA.StartSSL-vpn
crypto pki trustpoint TP-self-signed-1981248591
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1981248591
revocation-check none
rsakeypair TP-self-signed-1981248591
crypto pki trustpoint VMWare
enrollment terminal
revocation-check crl
crypto pki trustpoint OWA
enrollment terminal pem
revocation-check crl
crypto pki certificate chain TP.StartSSL.CA
certificate ca 01
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP.StartSSL-vpn
certificate 0936E1
    (removed the certificate info for clarity)9
   quit
certificate ca 18
(removed the certificate info for clarity)
   quit
crypto pki certificate chain TP-self-signed-1981248591
certificate self-signed 01
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain VMWare
certificate ca 008EDCE6DBCE6B
    (removed the certificate info for clarity)
   quit
crypto pki certificate chain OWA
   (removed the certificate info for clarity)
license udi pid CISCO1841 sn FCZ122191TW
archive
log config
hidekeys
username admin privilege 15 password 7 1304131F02023B7B7977
username ali password 7 06070328
redundancy
crypto isakmp policy 10
encr 3des
authentication pre-share
group 2
lifetime 84000
crypto isakmp key admin_123 address 0.0.0.0 0.0.0.0
crypto isakmp keepalive 10
crypto ipsec security-association lifetime seconds 28800
crypto ipsec transform-set vpnset esp-3des esp-sha-hmac
crypto ipsec transform-set strongsha esp-3des esp-sha-hmac
crypto dynamic-map mydyn 10
set transform-set strongsha
crypto map Dxb-Auh 1000 ipsec-isakmp dynamic XXXXXXXXXX
interface FastEthernet0/0
description Internal Network (Protected Interface)
ip address 10.236.5.254 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
shutdown
no atm ilmi-keepalive
interface BRI0/1/0
no ip address
encapsulation hdlc
shutdown
interface Virtual-Template1
ip unnumbered Dialer1
peer default ip address dhcp-pool ContosoPool
ppp encrypt mppe auto required
ppp authentication ms-chap ms-chap-v2 eap
interface Dialer1
ip ddns update hostname XXXXXXX.dyndns.org
ip ddns update dyndns
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1450
dialer pool 1
ppp pap sent-username vermam password 7 13044E155E0913323B
crypto map Dxb-Auh
interface Dialer2
mtu 1460
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer in-band
dialer idle-timeout 0
dialer string 123
dialer vpdn
dialer-group 2
ppp pfc local request
ppp pfc remote apply
ppp encrypt mppe auto
ppp authentication ms-chap ms-chap-v2 callin
ppp eap refuse
ppp chap hostname hasanreza
ppp chap password 7 070E2541470726544541
interface Dialer995
no ip address
ip local pool webssl 10.236.6.10 10.236.6.30
ip forward-protocol nd
ip http server
ip http secure-server
ip nat inside source list nat interface Dialer1 overload
ip nat inside source static tcp 10.236.5.12 25 interface Dialer1 25
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 172.21.51.0 255.255.255.0 10.236.5.253
ip access-list extended internal
permit ip any 10.236.5.0 0.0.0.255
ip access-list extended nat
deny   ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
deny   ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 any
ip access-list extended nonat
permit ip 10.236.5.0 0.0.0.255 172.19.19.0 0.0.0.255
permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
ip access-list extended sslacl
ip access-list extended webvpn
permit tcp any any eq 443
logging esm config
access-list 101 permit ip 10.236.5.0 0.0.0.255 172.31.1.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
line vty 5 15
exec-timeout 0 0
login local
transport preferred ssh
transport input telnet ssh
scheduler allocate 20000 1000
webvpn gateway gateway1
ip interface Dialer1 port 443
ssl encryption rc4-md5
ssl trustpoint TP.StartSSL-vpn
inservice
webvpn install svc flash:/webvpn/anyconnect-win-3.1.00495-k9.pkg sequence 1
webvpn install csd flash:/webvpn/sdesktop.pkg
webvpn context webvpn
ssl authenticate verify all
url-list "Webservers"
   heading "SimpleIT Technologies NBNS Servers"
   url-text "Google" url-value "www.google.com"
   url-text "Mainframe" url-value "10.236.5.2"
   url-text "Mainframe2" url-value "https://10.236.5.2"
nbns-list "ContosoServer"
   nbns-server 10.236.5.10
   nbns-server 10.236.5.11
   nbns-server 10.236.5.12
port-forward "PortForwarding"
   local-port 3389 remote-server "10.236.5.10" remote-port 3389 description "Server-DC01"
policy group policy1
   url-list "Webservers"
   port-forward "PortForwarding"
   nbns-list "ContosoServer"
   functions file-access
   functions file-browse
   functions file-entry
   functions svc-enabled
   svc address-pool "webssl"
   svc default-domain "Contoso.Local"
   svc keep-client-installed
   svc split include 10.236.5.0 255.255.255.0
   svc split include 10.236.6.0 255.255.255.0
   svc split include 172.31.1.0 255.255.255.0
   svc split include 172.21.51.0 255.255.255.0
   svc dns-server primary 172.21.51.10
default-group-policy policy1
gateway gateway1
inservice
end
Gateway#

PIX as PPTP client

Hi.
Can I configure a PIX (515), as PPTP client to establish a tunnel with non-Cisco PPTP server ? Can my PIX initiate this type of connection ?
Today, I use a PC with PPTP client to establish this and I want replace this with a PIX and I don´t want depends of a PC.
Thank you very much.

Hi Bro
The Cisco PIX firewall cannot act as a PPTP client, only PC/laptops in general can act as a PPTP client. The Cisco PIX can act as a PPTP Server though, if running on version 7.x and later. You could also refer to the comments made by Jennifer Halim (Cisco TAC engineer) in this URL https://supportforums.cisco.com/message/3207224
You might wanna explore other solutions. SuSEfirewall2 (software based firewall) supports PPTP client configuration http://pptpclient.sourceforge.net/howto-suse-100.phtml

Native VPN PPTP client won't stay connected

Folks,
I have setup my VPN using the Mac OSX native PPTP VPN client to connect to my client's work network. However, it appears that it won't stay connected. I have been searching the net for answers. I can't find a definitely one. Does anyone have the same issue where you can share your solution with me please?
To be more specific, I have a Windows XP laptop and a Mac. I connect to the same VPN on both machines. The Windows XP laptop will stay connected while the mac will drop the connection randomly. This is particularly true when my Mac went to sleep and then wake up.
In my PPTP VPN setup, I have already uncheck the option "Disconnect when user logs out" option in the Advance setting.
Also, this appears to be Mac OSX issue because I have another client where I can use the Cisco AnyWhere VPN client to connect and the connection stays connected all the time including the time when my Mac went into sleep mode.
My mac is the new MacBook Pro with Retina display running Mountain Lion (The original OS is Lion and then upgraded to Mountain Lion) and I am using the Thunderbolt to Ethernet adapter to connect to my wire network. It doesn't make much difference even if I switch over to a Wireless connection. In both cases, the VPN just won't stay connected.
Can someone point me to the right direction as to where I can trouble shoot this please? Thanks.

Thanks sberman. In the article, it mentions something about VPN on Demand, where in the setup do you see this setup? I am in the Network setup area and I am not finding this. Also, if I turn on the "Use verbose loggin", where is the log file? Is it still the /var/log/ppp.log file
Also, one more thing, my main ethernet connection setting does not include a proxy setting. But my VPN setup includes a proxy setting. Do you think that I may need to update the main ethernet setting to add the proxy setup to it as well? But I don't want to keep updating the main ethernet connection network setting to switch between proxy or not. Any suggestion will be welcome.
Thanks.

Cisco 857W that freeze when a lot of traffic travel over a VPN tunnel...

Hi to all...
i've a serious trouble with 2 cisco 857w...
They will freeze!
Between them there is a ipsec tunnel, over the vpn tunnel there are 2/3 termianl services connections, and some outlook/exchange clients.
While all work great when only 2 terminals are working, the branch office router(sometimes also the main office router...) stop responding when someone other onen outlook or open a new ts connection. Both lines are 4mb download and 512 upload, that must be emough...
The attached config is the sh run of the router that freeze only sometimes (the other that freezes frequently is 90% identical).
I avent's still updated the adsl FW...
[code]
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42
[/code]
Until not too much traffic is sent trougth the vpn tunnel, all ok, work really well.
Someone can help me how to find where is the problem?? It's a config problem??
Thanks to all!

I meant to say I have a MBPro and an IPAD 3...

Cisco IPSec VPN Client and sending a specific Radius A-V value to ACS 5.2

This setup is to try routing Cisco VPN to either RSA or Entrust from Cisco ACS 5.2, depending on some parameter in incoming AUTH request from Cisco IPSec VPN Client 5.x. Tried playing with pcf files and user names/identity stores, none seems working

Hi Tony,
to the best of my knowledge this is currently not possible, but will be once this enhancement is implemented:
CSCsw31922 Radius upstream VSAs (Tunnel Group,Client type) for VPN policy decisions
You may want to try and ask in the AAA forum if there is anything you can do on ACS...
hth
Herbert

Small Sales Office with Cisco 857W and Wireless Skype Handset

I have a remote sales office which is connected to the internet via a Cisco 857W. One of the sales guys uses a Skype Wireless Handset. I am looking to improve the quality of the handset as much as I can with the local wireless network in the 857W. The handset has WMM (802.11e) and uses ports 1 (alternative ports 80 and 443). My question is how do I enable WMM (802.11e) on this router and how do I or should I give priority to these ports to improve call quality? Config file attached.
thanks in advance,
stuart.

I'm not an expert on this subject but this link could help.
http://www.cisco.com/en/US/products/ps5853/products_configuration_guide_chapter09186a008067cc16.html

NAC-L2-802.1x (EAP-FAST) and Cisco Secure Services Client 5.0 in wired net

Hi!
(Sorry, if this is a wrong forum.)
Does anybody have any success with Cisco SSC and EAP-FAST in the wired network?
I'm going to use NAC, so I'm trying to set up EAP-FAST. I see the pop-up window on the client to enter user credentials and I see a lot of "debug radius" messages on my 3750 12.2(44)SE switch:
Access-Requests with User-Name="anonymous"
Access-Challenges (I see certificate is sent from ACS)
Access-Reject
CS ACS Failed Attempts Report shows "ACS user unknown" failure for "anonymous".
So far as I understood, EAP-FAST is a tunneled method and it uses "anonymous" to protect user's identity during phase 0 / phase 1 transactions. The actual username is sent in phase 2 transaction.
The following is excerpt from the CS ACS documentation:
"EAP-FAST can protect the username in all EAP-FAST transactions. ACS does not perform user authentication based on a username that is presented in phase one; however, whether the username is protected during phase one depends on the end-user client. If the end-user client does not send the real username in phase one, the username is protected. The Cisco Aironet EAP-FAST client protects the username in phase one by sending FAST_MAC address in place of the username. After phase one of EAP-FAST, all data is encrypted, including username information that is usually sent in clear text."
SSC 5.0 is indeed set up with "Unprotected Identity Pattern"=anonymous and "Protected Identity Pattern"=[username] using sscManagementUtility.exe
So, the question is: Why is ACS 4.1 trying to authenticate username "anonymous" if it knows that the user is fake? Does anybody have working configuaration for EAP-FAST in a wired network?
Any help is greatly appreciated.

Correct, ACS database wasn't selected on the NAP Authentication page. It works now, but I constantly get the following message in the Windows event log: "The Cisco Secure Services Client service hung on starting". This is Windows 2000 Advanced Server system with SP4. SSC was set up with no domain authentication, no machine authentication, single sign-on. After some time the SSC service starts, but at that time my PC is already put into the guest VLAN by the switch (the tx-period is 10 seconds):
POD1-SW#sh run int fa1/0/1
Building configuration...
Current configuration : 378 bytes
interface FastEthernet1/0/1
switchport access vlan 999
switchport mode access
dot1x mac-auth-bypass
dot1x pae authenticator
dot1x port-control auto
dot1x timeout reauth-period server
dot1x timeout tx-period 10
dot1x reauthentication
dot1x critical
dot1x critical recovery action reinitialize
dot1x guest-vlan 91
dot1x critical vlan 11
spanning-tree portfast
end
After all the VLAN is reassigned by the switch, but the delay is too high. How can I troubleshoot this?
Thx.

Install Error when installing CISCO AnyConnect Mobility Client

When installing Cisco AnyConnect Mobility Client 3.1.02040, I get the following install error:
There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor.

When installing Cisco AnyConnect Mobility Client 3.1.02040, I get the following install error:
There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor.

Installing pptp client

Hi Gurus,
I downloaded pptp client from sourceforge.net i am trying to install it on Solaris 10 x86 laptop but i get the following errors, can you please help a lost friend here:
bash-3.00# /usr/local/bin/make
gcc -o pptp pptp.o pptp_gre.o ppp_fcs.o pptp_ctrl.o dirutil.o vector.o inststr.o util.o version.o test.o pptp_quirks.o orckit_quirks.o pqueue.o pptp_callmgr.o routing.o pptp_compat.o -lutil
ld: fatal: library -lutil: not found
ld: fatal: File processing errors. No output written to pptp
collect2: ld returned 1 exit status
make: *** [pptp] Error 1
thanks in advance

Hi, thanks for reply, i tried that but now i get this error:
bash-3.00# /usr/local/bin/make
gcc -o pptp pptp.o pptp_gre.o ppp_fcs.o pptp_ctrl.o dirutil.o vector.o inststr.o util.o version.o test.o pptp_quirks.o orckit_quirks.o pqueue.o pptp_callmgr.o routing.o pptp_compat.o
Undefined first referenced
symbol in file
bind pptp_gre.o
accept pptp_callmgr.o
listen pptp_callmgr.o
gethostbyname pptp.o
socket pptp.o
getsockopt pptp_gre.o
connect pptp.o
inet_aton pptp_callmgr.o
inet_pton pptp.o
inet_ntoa pptp.o
h_errno pptp.o
ld: fatal: Symbol referencing errors. No output written to pptp
collect2: ld returned 1 exit status
make: *** [pptp] Error 1
please help!

Local RADIUS in AP1242 with non-cisco WinXP wireless clients

I'd like to configure local RADIUS in AP1242 and connect non-cisco WinXP wireless clients (for example notebook with integrated radio) with it. I did configuration (config1.txt) like in instruction: http://cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c0912.shtml
But I can't connect non-cisco WinXP wireless client with AP1242 anyway. At once Cisco wireless client with Aironet Desktop Utility connects with it without any problem. I've done some other configuration (config2.txt), but with the same result. Second configuration is rather then first.
How can I connect non-cisco WinXP wireless clients with AP1242 with local RADIUS?

Hi Stephen,
Thanks for the quick reply. Below is the switchport config. I am able to ping the AP from the switch and connect to its web page from any workstations.
interface GigabitEthernet0/5
switchport trunk encapsulation dot1q
switchport trunk native vlan 151
switchport mode trunk
end

Configurate cisco ipsec vpn client at asa 5505 version 8.4

Hi dear. I want to configurate cisco ipsec vpn client at asa 5505. At my asa the software version is 8.4.
please provide me a link or some material to config ipsec vpn client at asa 5505 version 8.4
thank you.

are you looking for vpn client .pcf file or the configuration on ASA (ASDM) ?
what version of vpn client ?

Cisco Systems VPN Client Version 5.0.03.0560 Errors

Hello I am getting the following errors on my
VPN Connection Attempts
Cisco Systems VPN Client Version 5.0.03.0560
Copyright (C) 1998-2007 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 5.1.2600 Service Pack 3
Config file directory: C:\Program Files\Cisco Systems\VPN Client\
1      19:59:14.375 09/26/10 Sev=Warning/3 CVPND/0xA340000D
The virtual adapter was not recognized by the operating system.
2      19:59:14.375 09/26/10 Sev=Warning/2 CM/0xE310000A
The virtual adapter failed to enable
3      19:59:14.531 09/26/10 Sev=Warning/2 IKE/0xE300009B
Failed to active IPSec SA: Unable to enable Virtual Adapter (NavigatorQM:936)
4      19:59:14.531 09/26/10 Sev=Warning/2 IKE/0xE30000A7
Unexpected SW error occurred while processing Quick Mode negotiator:(Navigator:2238)

Please kindly check the following readme for VPN Client version 5.0.3.560:
http://www.cisco.com/web/software/282364316/22941/vpnclient-windows-5.0.03.0560.txt
Advisory:
The new client requires a kernel patch, KB952876, from Microsoft before installing first before installing the actual client.
REF: http://support.microsoft.com/kb/952876/en-us
Pls kindly check if you have kernel patch KB952876

MBA (mid 2013) and Cisco Jabber Video client not recognising any camera

The Cisco Jabber Video client is not recognising the internal Facetime HD camera nor the external USB Logitech Webcam C920.
This was not working from the beginning. Cisco is aware of this issue and promised to deliver a fix in the next release of their software.
After installing the 10.8.5 Update from App Store and the 10.8.5 Supplemental update the Cisco client was able to recognize the external camera.
After that I followed a hint to install the Combo update this should enable Skype to recognise the Facetime HD camera. After installing the Combo update Skype was able to recognize the internal and external camera (by the way the quality of preview video using Facetime HD was brilliant and much better than the internal camera of a MBA from 2012). BUT after that update the Cisco client was no longer recognising a camera.
I run a recovery installation of 10.8.4 - but the result was again a 10.8.5. If I try now to run a recovery install I only get a recovery of version 10.8.5 offered.
I did a SMC reset, a parameter RAM reset, tried to start in saved mode but nothing helped.
Any other ideas how to get a least an external camera working again with Cisco Jabber Video?

Similar problem here. I have a Logitech C615 camera/microphone plugged into my MAC mini running OSX 10.9.3. Today, JABBER could not find the camera (although it found the microphone?). I was running 4.5.7 and so downloaded v4.8.6 and reinstalled: no camera. I also downloaded the cloud version: no camera.
I was not running either Vidyo or Polycom RealPresence at the same time as JABBER
But, when I did run these apps, my camera & microphone both work.
Suggestions?
John

Why doesn't iPad PPTP client support compression?

When using iPad or iPhone as a PPTP client they don't make any use of the compression protocol available and offered by the PPTP server?
Why is that????

Because they don't, maybe.
User to user forum, no Apple here.
We have no idea why Apple does anything, all anyone here can do is speculate.

Cisco 857w PPTP client?

Similar Messages

Maybe you are looking for