Cisco 871w, radius server local, and leap or eap-fast will not authenticate
Hello, i trying to setup eap-fast or leap on my 871w. i belive i have it confiured correctly but i can not get any device to authenticate to router. Below is the confiureation that i being used. any help would be welcome!
! Last configuration change at 15:51:30 AZT Wed Jan 4 2012 by testtest
! NVRAM config last updated at 15:59:37 AZT Wed Jan 4 2012 by testtest
version 12.4
configuration mode exclusive auto
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service pt-vty-logging
service sequence-numbers
hostname router871
boot-start-marker
boot-end-marker
logging count
logging message-counter syslog
logging buffered 4096
logging rate-limit 512 except critical
logging console critical
enable secret 5 <omitted>
aaa new-model
aaa group server radius rad-test3
server 192.168.16.49 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login eap-methods group rad-test3
aaa authorization exec default local
aaa session-id common
clock timezone AZT -7
clock save interval 8
dot11 syslog
dot11 ssid test2
vlan 2
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 <omitted>
dot11 ssid test1
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 <omitted>
dot11 ssid test3
vlan 3
authentication open eap eap-methods
authentication network-eap eap-methods
no ip source-route
no ip gratuitous-arps
ip options drop
ip dhcp bootp ignore
ip dhcp excluded-address 192.162.16.49 192.162.16.51
ip dhcp excluded-address 192.168.16.33
ip dhcp excluded-address 192.168.16.1 192.168.16.4
ip dhcp pool vlan1pool
import all
network 192.168.16.0 255.255.255.224
default-router 192.168.16.1
domain-name test1.local.home
lease 4
ip dhcp pool vlan2pool
import all
network 192.168.16.32 255.255.255.240
default-router 192.168.16.33
domain-name test2.local.home
lease 0 6
ip dhcp pool vlan3pool
import all
network 192.168.16.48 255.255.255.240
default-router 192.168.16.49
domain-name test3.local.home
lease 2
ip cef
ip inspect alert-off
ip inspect max-incomplete low 25
ip inspect max-incomplete high 50
ip inspect one-minute low 25
ip inspect one-minute high 50
ip inspect udp idle-time 15
ip inspect tcp idle-time 1800
ip inspect tcp finwait-time 30
ip inspect tcp synwait-time 60
ip inspect tcp block-non-session
ip inspect tcp max-incomplete host 25 block-time 2
ip inspect name firewall tcp router-traffic
ip inspect name firewall ntp
ip inspect name firewall ftp
ip inspect name firewall udp router-traffic
ip inspect name firewall pop3
ip inspect name firewall pop3s
ip inspect name firewall imap
ip inspect name firewall imap3
ip inspect name firewall imaps
ip inspect name firewall smtp
ip inspect name firewall ssh
ip inspect name firewall icmp router-traffic timeout 10
ip inspect name firewall dns
ip inspect name firewall h323
ip inspect name firewall hsrp
ip inspect name firewall telnet
ip inspect name firewall tftp
no ip bootp server
no ip domain lookup
ip domain name local.home
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip accounting-threshold 100
ip accounting-list 192.168.16.0 0.0.0.31
ip accounting-list 192.168.16.32 0.0.0.15
ip accounting-list 192.168.16.48 0.0.0.15
ip accounting-transits 25
login block-for 120 attempts 5 within 60
login delay 5
login on-failure log
memory free low-watermark processor 65536
memory free low-watermark IO 16384
username testtest password 7 <omitted>
archive
log config
logging enable
logging size 255
notify syslog contenttype plaintext
hidekeys
path tftp://<omitted>/archive-config
write-memory
ip tcp synwait-time 10
ip ssh time-out 20
ip ssh authentication-retries 2
ip ssh logging events
ip ssh version 2
bridge irb
interface Loopback0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
shutdown
interface FastEthernet1
switchport mode trunk
shutdown
interface FastEthernet2
shutdown
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description Cox Internet Connection
ip address dhcp
ip access-group ingress-filter in
ip access-group egress-filter out
no ip redirects
no ip unreachables
no ip proxy-arp
ip accounting access-violations
ip flow ingress
ip flow egress
ip inspect firewall out
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
load-interval 30
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 2 mode ciphers aes-ccm
encryption key 1 size 128bit 7 <omitted> transmit-key
encryption mode wep mandatory
broadcast-key vlan 1 change <omitted> membership-termination
broadcast-key vlan 3 change <omitted> membership-termination
broadcast-key vlan 2 change <omitted> membership-termination
ssid test2
ssid test1
ssid test3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
rts threshold 2312
no cdp enable
interface Dot11Radio0.1
description <omitted>
encapsulation dot1Q 1 native
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description <omitted>
encapsulation dot1Q 2
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
description <omitted>
encapsulation dot1Q 3
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan1
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan2
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 2
bridge-group 2 spanning-disabled
interface Vlan3
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 3
bridge-group 3 spanning-disabled
interface BVI1
description <omitted>
ip address 192.168.16.1 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI2
description <omitted>
ip address 192.168.16.33 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI3
description <omitted>
ip address 192.168.16.49 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip http secure-ciphersuite 3des-ede-cbc-sha rc4-128-sha
ip http timeout-policy idle 5 life 43200 requests 5
ip flow-top-talkers
top 10
sort-by bytes
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.16.50 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.16.50 53 interface FastEthernet4 53
ip nat inside source static tcp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 88 interface FastEthernet4 88
ip nat inside source static udp 192.168.16.50 53 interface FastEthernet4 53
ip access-list extended egress-filter
deny ip any host <omitted>
deny ip any host <omitted>
deny ip host <omitted> any
deny ip host <omitted> any
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.10.9.255 any
deny ip 10.0.0.0 0.10.13.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.15.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
permit ip <omitted> 0.0.0.3 any
deny ip any any log
ip access-list extended ingress-filter
remark ----- To get IP form COX -----
permit udp any eq bootps any eq bootpc
deny icmp any any log
deny udp any any eq echo
deny udp any eq echo any
deny tcp any any fragments
deny udp any any fragments
deny ip any any fragments
deny ip any any option any-options
deny ip any any ttl lt 4
deny ip any host <omitted>
deny ip any host <omitted>
deny udp any any range 33400 34400
remark ----- Bogons Filter -----
deny ip 0.0.0.0 0.255.255.255 any
deny ip 10.0.0.0 0.255.255.255 any
deny ip 127.0.0.0 0.255.255.255 any
deny ip 169.254.0.0 0.0.255.255 any
deny ip 172.16.0.0 0.15.255.255 any
deny ip 192.0.0.0 0.0.0.255 any
deny ip 192.0.2.0 0.0.0.255 any
deny ip 192.168.0.0 0.0.255.255 any
deny ip 198.18.0.0 0.1.255.255 any
deny ip 198.51.100.0 0.0.0.255 any
deny ip 203.0.113.0 0.0.0.255 any
deny ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
deny ip 10.10.10.0 0.0.0.255 any
deny ip 10.10.11.0 0.0.0.255 any
deny ip 10.10.12.0 0.0.0.255 any
deny ip any any log
access-list 1 permit 192.168.16.0 0.0.0.63
access-list 20 permit 127.127.1.1
access-list 20 permit 204.235.61.9
access-list 20 permit 173.201.38.85
access-list 20 permit 216.229.4.69
access-list 20 permit 152.2.21.1
access-list 20 permit 130.126.24.24
access-list 21 permit 192.168.16.0 0.0.0.63
radius-server local
no authentication mac
eapfast authority id <omitted>
eapfast authority info <omitted>
eapfast server-key primary 7 <omitted>
nas 192.168.16.49 key 7 <omitted>
group rad-test3
vlan 3
ssid test3
user test nthash 7 <omitted> group rad-test3
user testtest nthash 7 <omitted> group rad-test3
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.16.49 auth-port 1812 acct-port 1813 key 7 <omitted>
radius-server vsa send accounting
control-plane host
control-plane transit
control-plane cef-exception
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
bridge 3 protocol ieee
bridge 3 route ip
line con 0
password 7 <omitted>
logging synchronous
no modem enable
transport output telnet
line aux 0
password 7 <omitted>
logging synchronous
transport output telnet
line vty 0 4
password 7 <omitted>
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
process cpu threshold type total rising 80 interval 10 falling 40 interval 10
ntp authentication-key 1 md5 <omitted> 7
ntp authenticate
ntp trusted-key 1
ntp source FastEthernet4
ntp access-group peer 20
ntp access-group serve-only 21
ntp master 1
ntp server 152.2.21.1 maxpoll 4
ntp server 204.235.61.9 maxpoll 4
ntp server 130.126.24.24 maxpoll 4
ntp server 216.229.4.69 maxpoll 4
ntp server 173.201.38.85 maxpoll 4
end
so this what i am getting now for debug? any thoughs?
010724: Jan 5 16:26:04.527 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/2
010725: Jan 5 16:26:08.976 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/2
010726: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010727: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010728: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010729: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010730: Jan 5 16:26:08.976 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010731: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010732: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010733: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010734: Jan 5 16:26:08.976 AZT: EAPOL pak dump tx
010735: Jan 5 16:26:08.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010736: Jan 5 16:26:08.976 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0AD05650: 01000004 04010004 ........
0AD05660:
010737: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 1
010738: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010739: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010740: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010741: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 0
010742: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
010743: Jan 5 16:26:08.980 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010744: Jan 5 16:26:08.984 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010745: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010746: Jan 5 16:26:09.624 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010747: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: req->auth_type 0
010748: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010749: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010750: Jan 5 16:26:09.624 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010751: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010752: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010753: Jan 5 16:26:09.624 AZT: EAPOL pak dump tx
010754: Jan 5 16:26:09.624 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010755: Jan 5 16:26:09.624 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010756: Jan 5 16:26:09.644 AZT: dot11_auth_send_msg: sending data to requestor status 1
010757: Jan 5 16:26:09.648 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010758: Jan 5 16:26:09.648 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010759: Jan 5 16:26:09.656 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010760: Jan 5 16:26:09.656 AZT: EAPOL pak dump rx
010761: Jan 5 16:26:09.656 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010762: Jan 5 16:26:09.656 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0B060D50: 01000009 02010009 ........
0B060D60: 01746573 74 .test
010763: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010764: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010765: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010766: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198):Orig. component type = DOT11
010767: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010768: Jan 5 16:26:09.664 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010769: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010770: Jan 5 16:26:09.664 AZT: RADIUS: 36 [6]
010771: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010772: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198): acct_session_id: 408
010773: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010774: Jan 5 16:26:09.664 AZT: RADIUS(00000198): sending
010775: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Send Access-Request to 162.168.16.49:1645 id 1645/3, len 133
010776: Jan 5 16:26:09.664 AZT: RADIUS: authenticator BF 69 DD DF 89 1F C6 FB - EF EC 12 EB C5 3F 3A CD
010777: Jan 5 16:26:09.664 AZT: RADIUS: User-Name [1] 6 "test"
010778: Jan 5 16:26:09.664 AZT: RADIUS: Framed-MTU [12] 6 1400
010779: Jan 5 16:26:09.664 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010780: Jan 5 16:26:09.664 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010781: Jan 5 16:26:09.668 AZT: RADIUS: Service-Type [6] 6 Login [1]
010782: Jan 5 16:26:09.668 AZT: RADIUS: Message-Authenticato[80] 18
010783: Jan 5 16:26:09.668 AZT: RADIUS: 5B FA 47 07 0E E3 4B 71 7F 60 6E 4E 91 37 84 A6 [[?G???Kq?`nN?7??]
010784: Jan 5 16:26:09.668 AZT: RADIUS: EAP-Message [79] 11
010785: Jan 5 16:26:09.668 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010786: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010787: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port [5] 6 661
010788: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Id [87] 5 "661"
010789: Jan 5 16:26:09.668 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010790: Jan 5 16:26:09.668 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010791: Jan 5 16:26:14.501 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010792: Jan 5 16:26:19.018 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010793: Jan 5 16:26:23.739 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010794: Jan 5 16:26:28.700 AZT: RADIUS: Fail-over to (162.168.16.49:1812,1813) for id 1645/3
router871#
010795: Jan 5 16:26:33.629 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010796: Jan 5 16:26:38.494 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010797: Jan 5 16:26:39.794 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010798: Jan 5 16:26:39.794 AZT: EAPOL pak dump rx
010799: Jan 5 16:26:39.794 AZT: EAPOL Version: 0x1 type: 0x1 length: 0x0000
0AD053D0: 01010000 ....
010800: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,EAP_START) for d8b3.7759.0488
010801: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_ignore_event: Ignore event: do nothing
router871#
010802: Jan 5 16:26:43.007 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010803: Jan 5 16:26:47.336 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/3
010804: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010805: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010806: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010807: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010808: Jan 5 16:26:47.336 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010809: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010810: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010811: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010812: Jan 5 16:26:47.336 AZT: EAPOL pak dump tx
010813: Jan 5 16:26:47.336 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010814: Jan 5 16:26:47.336 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0B060710: 01000004 04010004 ........
0B060720:
010815: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 1
010816: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010817: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010818: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010819: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 0
010820: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
router871#
010821: Jan 5 16:26:47.340 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010822: Jan 5 16:26:47.344 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010823: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010824: Jan 5 16:26:47.972 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010825: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: req->auth_type 0
010826: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010827: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010828: Jan 5 16:26:47.976 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010829: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010830: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010831: Jan 5 16:26:47.976 AZT: EAPOL pak dump tx
010832: Jan 5 16:26:47.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010833: Jan 5 16:26:47.976 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50: 01000031 01010031 ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30 r871,portid=0
010834: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: sending data to requestor status 1
010835: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010836: Jan 5 16:26:47.996 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010837: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010838: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
router871#
010839: Jan 5 16:26:47.996 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
router871#
010840: Jan 5 16:26:58.634 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010841: Jan 5 16:26:58.634 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010842: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: req->auth_type 0
010843: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010844: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010845: Jan 5 16:26:58.638 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010846: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010847: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010848: Jan 5 16:26:58.638 AZT: EAPOL pak dump tx
010849: Jan 5 16:26:58.638 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010850: Jan 5 16:26:58.638 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060710: 01000031 01010031 ...1...1
0B060720: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060730: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B060740: 72383731 2C706F72 7469643D 30 r871,portid=0
010851: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: sending data to requestor status 1
010852: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010853: Jan 5 16:26:58.658 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010854: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010855: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
010856: Jan 5 16:27:01.603 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010857: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list ingress-filter denied tcp 32.42.41.254(57443) -> 72.201.117.84(59652), 1 packet
010858: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list egress-filter denied tcp 22.3.184.118(0) -> 74.125.53.188(0), 4 packets
010859: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010860: Jan 5 16:27:12.261 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010861: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: req->auth_type 0
010862: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010863: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010864: Jan 5 16:27:12.261 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010865: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010866: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010867: Jan 5 16:27:12.261 AZT: EAPOL pak dump tx
010868: Jan 5 16:27:12.261 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010869: Jan 5 16:27:12.261 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060FD0: 01000031 01010031 ...1...1
0B060FE0: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060FF0: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B061000: 72383731 2C706F72 7469643D 30 r871,portid=0
010870: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: sending data to requestor status 1
010871: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010872: Jan 5 16:27:12.285 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010873: Jan 5 16:27:12.293 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010874: Jan 5 16:27:12.293 AZT: EAPOL pak dump rx
010875: Jan 5 16:27:12.293 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010876: Jan 5 16:27:12.293 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0AD05290: 01000009 02010009 ........
0AD052A0: 01746573 74 .test
010877: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010878: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010879: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010880: Jan 5 16:27:12.301 AZT: RADIUS/ENCODE(0000019B):Orig. component type = DOT11
010881: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: ssid [282] 8
010882: Jan 5 16:27:12.305 AZT: RADIUS: 74 6F 79 73 6F 6E [toyson]
010883: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: interface [175] 3
010884: Jan 5 16:27:12.305 AZT: RADIUS: 36 [6]
010885: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010886: Jan 5 16:27:12.305 AZT: RADIUS/ENCODE(0000019B): acct_session_id: 411
010887: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010888: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): sending
010889: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Send Access-Request to 162.168.16.49:1645 id 1645/4, len 133
010890: Jan 5 16:27:12.305 AZT: RADIUS: authenticator 6F 6C 63 31 88 DE 30 A2 - C2 06 12 EB 50 A3 53 36
010891: Jan 5 16:27:12.305 AZT: RADIUS: User-Name [1] 6 "test"
010892: Jan 5 16:27:12.305 AZT: RADIUS: Framed-MTU [12] 6 1400
010893: Jan 5 16:27:12.305 AZT: RADIUS: Called-Station-Id [30] 16 "0019.3075.e660"
010894: Jan 5 16:27:12.305 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010895: Jan 5 16:27:12.305 AZT: RADIUS: Service-Type [6] 6 Login [1]
010896: Jan 5 16:27:12.305 AZT: RADIUS: Message-Authenticato[80] 18
010897: Jan 5 16:27:12.305 AZT: RADIUS: 9D D5 62 1A 38 13 94 30 3A 43 D7 A4 AE A4 43 64 [??b?8??0:C????Cd]
010898: Jan 5 16:27:12.305 AZT: RADIUS: EAP-Message [79] 11
010899: Jan 5 16:27:12.305 AZT: RADIUS: 02 01 00 09 01 74 65 73 74 [?????test]
010900: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port-Type [61] 6 802.11 wireless [19]
010901: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port [5] 6 664
010902: Jan 5 16:27:12.309 AZT: RADIUS: NAS-Port-Id [87] 5 "664"
010903: Jan 5 16:27:12.309 AZT: RADIUS: NAS-IP-Address [4] 6 192.168.16.49
010904: Jan 5 16:27:12.309 AZT: RADIUS: Nas-Identifier [32] 11 "router871"
010905: Jan 5 16:27:16.642 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/4
Similar Messages
-
Cableone innstalled a new server and now my thunderbird email will not work. What do I do now?
Cableone, our internet provider, has changed from a Google server to their own server and now my Thunderbird email will not work. They have directions listed to make it work, but this does not work. I have also contacted Cableone's technical support and they say because thunderbird is not their system they have no responsibility to make it work. I prefer to use Thunderbird for my email - how can I make it work? Also, I have tried the Thunderbird 'Automatic Account Configuration' help and it does not work.
Ask your less than helpful provider for the server settings and setup the new account up manually.
You want to know IMAP or POP and the name of the server. The port number and if it uses SSL/TLS security.
You need the same info for the SMTP server for outbound mail. -
Cisco 1142 Wireless access point intermittently will not authenticate
Hi all,
We have a Cisco 1142 standalone access point, and from time to time I will come into the office and it will not authenticate any users to either our guest or corporate networks. I then have to go in and reboot the access point. After that, it begins to work. Any advice? Here's my configuration below:
Current configuration : 6450 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname cisco-chiap01
logging monitor errors
enable secret 5 $1$fsD8$CU42/3/Up5AAlL4hQWvvg0
aaa new-model
aaa group server radius rad_eap
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa group server radius rad_eap2
server 172.17.16.12 auth-port 1645 acct-port 1646
server 172.17.21.10 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods2 group rad_eap2
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
login on-failure log
login on-success log
dot11 syslog
dot11 vlan-name Admin vlan 100
dot11 vlan-name DevNetwork vlan 20
dot11 vlan-name Guest vlan 150
dot11 vlan-name Network vlan 16
dot11 ssid DevNetwork
vlan 20
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
dot11 ssid Guest
vlan 150
authentication open
authentication key-management wpa version 2
guest-mode
mbssid guest-mode
wpa-psk ascii 7 142407060101380B013A3A2670435642
information-element ssidl advertisement
dot11 ssid Network
vlan 16
authentication open eap eap_methods2
authentication network-eap eap_methods2
authentication key-management wpa version 2
username monkeyman privilege 15 secret 5 $1$ZZ7C$rqimu2FNONdfeacMNGAD/.
bridge irb
interface Dot11Radio0
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
parent timeout 120
speed 5.5 11.0 basic-6.0 9.0 12.0 36.0 48.0 54.0
packet retries 128 drop-packet
channel 2462
station-role root
rts threshold 512
rts retries 128
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface Dot11Radio1
no ip address
ip helper-address 172.17.19.10
no ip route-cache
encryption vlan 16 mode ciphers aes-ccm
encryption vlan 150 mode ciphers aes-ccm
encryption vlan 20 mode ciphers aes-ccm
ssid DevNetwork
ssid Guest
ssid Network
antenna gain 0
traffic-metrics aggregate-report
dfs band 3 block
mbssid
parent timeout 120
speed 6.0 12.0 basic-24.0 36.0 48.0 54.0
channel width 40-above
channel dfs
station-role root access-point
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
interface Dot11Radio1.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
bridge-group 150 subscriber-loop-control
bridge-group 150 block-unknown-source
no bridge-group 150 source-learning
no bridge-group 150 unicast-flooding
bridge-group 150 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.11
encapsulation dot1Q 11
no ip route-cache
interface GigabitEthernet0.16
encapsulation dot1Q 16 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface GigabitEthernet0.100
encapsulation dot1Q 100
ip address 192.168.100.3 255.255.255.0
no ip route-cache
bridge-group 100
no bridge-group 100 source-learning
bridge-group 100 spanning-disabled
interface GigabitEthernet0.150
encapsulation dot1Q 150
no ip route-cache
bridge-group 150
no bridge-group 150 source-learning
bridge-group 150 spanning-disabled
interface BVI1
ip address 172.17.16.251 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface GigabitEthernet0
access-list 1 permit 172.17.16.1
access-list 1 remark Admin network access
access-list 1 permit 192.168.100.0 0.0.0.255
radius-server attribute 32 include-in-access-req format %h
radius-server host 172.17.21.10 auth-port 1812 acct-port 1813 key 7 047958071C3561410D4A44
radius-server host 172.17.16.12 auth-port 1645 acct-port 1646 key 7 08045E471A48574446
radius-server host 172.17.21.10 auth-port 1645 acct-port 1646 key 7 1320051B185D56797F
radius-server timeout 15
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
access-class 1 in
endWhen the issue occurs does that affect both 2.4GHz & 5GHz devices ? I would see which band operating devices affected.
I noticed you have set CH11 under Radio 0 statically. I would prefer to configure it as below so AP can change the channel depend on the environment.
int d0
channel least-congested
HTH
Rasika
**** Pls rate all useful responses **** -
For the last 10 days I have been unable to open the Mail account on my eMac (MacOS10.4.11). When I click on the icon in the Dock the only option I get is "Force quit" and the main Mail bar will not open any choice. Any ideas?
You can setup Mail for iCloud on the eMac.
Do not delete the old account yet. sign up for an iCloud account if you haven't.
I understand .mac mail will still come through. Do not delete the old account yet.
You cannot use .mac or MobileMe as type of Account, you have to choose IMAP when setting up, otherwise Mail is hard coded to change imap.mail.me.com to mail.me.com & smtp.mail.me.com to smtp.me.com, no matter what you try to enter.
iCloud Mail setup, do not choose .mac or MobileMe as type, but choose IMAP...
On second step where it asks "Description", it has to be a unique name, but you can still use your email address.
IMAP (Incoming Mail Server) information:
• Server name: imap.mail.me.com
• SSL Required: Yes
• Port: 993
• Username: [email protected] (use your @me.com address from your iCloud account)
• Password: Your iCloud password
SMTP (outgoing mail server) information:
• Server name: smtp.mail.me.com
• SSL Required: Yes
• Port: 587
• SMTP Authentication Required: Yes
• Username: [email protected] (use your @me.com address from your iCloud account)
• Password: Your iCloud password -
Can not get email after updating to 8.1.1! Deleted account and now cannot add as will not verify due to Apple something timeout messages? Any one else having problems?
Hi tania184,
Have you contacted your email provider to make sure there are no problems on their end? If they say their email servers are working properly, check the outgoing and incoming mail servers entries on your iPhone to make sure both are entered correctly. Enter the outgoing mail server even if the account setup indicates that is optional. -
I just ran the 9.1 update for CF and now the adminastrator page will not load
I just ran the 9.1 update for CF and now the administrator page will not load, the site runs but that is it I know I'm missing something. I have rebooted the server. No change and all the services are running. I am on the server not trying remotely .
Message was edited by: Norman RothwellHi Norman,
Can you please confirm if you ran the Update 9.1 or any patch.
Regards,
Priyank -
My new apps have changed to try within creative cloud; and my installed apps will not authenticate. I recently canceled one subscription and replaced it with another. Can you please look at it and correct?
Solution for Windows 8.1: Locate the C:\Users\USER\AppData\Local\Adobe\OOBE folder. Log out of Creative Cloud and from Task Manager end task for Creative Cloud. From the OOBE folder delete ALL files. Do not delete folders (com.adobe.accc.apps & com.adobe.accc.home). When complete, restart Creative Cloud and log in with ID and Password.
-
How do i restore my wifi setting back to the factory settings? I have changed it somehow :/ and now my wifi will not connect. My Airport is on and showing full strength but will not connect.
Ok, if other devices are connecting but just not your MacBook then let's start troubleshooting the MacBook to possibly find out why.
Please try each of the following, in order, until hopefully resolved:
Note the following are excerpts from an OS X Daily article.
* Turn Airport on & off – You can do this via the Airport menu bar or from the Network Preferences. This is the first thing you should try when troubleshooting Mac wireless problems.
* Make sure Wireless/Airport card software & firmware is up to date – This is usually done just by going to the Software Update menu, if there are any updates available for your Mac or Airport, install them.
* Delete and recreate connection – Try deleting and recreating/reestablishing the wireless connection, sometimes a setting can be corrupted and this may fix it.
* Create a new Network Location – Similar to the above suggestion, try creating a new and different wireless network location to see if it resolves the connection problems.
* Change DHCP auto settings to manual – sometimes there is a problem with the DHCP server, and if you manually set an IP address on the network you can be fine. Remember to set the IP to a high number so it wouldn’t interfere with other DHCP machines. As long as you have the subnet mask, router, and DNS settings configured manually as well, this shouldn’t be a problem.
* Flush the DNS cache – Launch the Terminal and enter the following command onto one full line within the Terminal: dscacheutil -flushcache
* Zap the PRAM – Reboot your Mac and hold Command+Option+P+R during restart until you hear another chime, let the Mac boot as usual.
* Delete Wireless Config files – Delete com.apple.internetconfigpriv.plist and com.apple.internetconfig.plist files from ~/Library/Preferences and reboot
* Trash your home directories SystemConfiguration – Remove all files within ~/Library/Preferences/SystemConfiguration/ and then reboot your Mac.
* Reset your Mac’s System Management Controller (SMC) – For MacBook and MacBook Pro’s: Shutdown the MacBook/Pro, remove the battery, disconnect the power, hold the Power Key for 15 seconds. Replace the battery, reconnect power, and zap the PRAM and wait for 2 chimes before letting the keys go. Let boot as usual. -
I have a new iPhone 4s. I have a home wi-fi network using Cisco Linksys2000 router with all settings per this article - phone will not see network if set to 5 GHz channel width - solution?? 2.4 works but is not optimal with other devices in home (computers; tivo). Have others seen this? Any advice is much appreciated.
Stephen Spark is right - your best alternative is to use a simultaneous dual band wireless router like the AirPort Extreme. Your Cisco Linksys2000 is not a dual band router, meaning that it will be constrained to operate at the slowest speed of all the devices on your network.
The AirPort Extreme's dual networks will support all your 802.11n devices as well as all your 802.11b/g devices on both the 2.4 and 5 GHz frequencies simultaneously. -
W2K will not authenticate to Mac OS X Server.
My Mac OS X 10.4.3 will authenticate via Open Directory, but my Windows 2000 Pro. machine will not authenticate with Active Directory. Is there any trick to get Active Directory running on the OS X Server?
Thanks.Your question would be easier to answer if you had included information of what Mac you have and what version of Garageband you are trying to reinstall.
And why you deleted it in the first place. -
An Album (CD) that I have successfully imported into iTunes, and synced with my iPod, will NOT sync with my iPad, even though I have done everything I know how to do so. When viewing the music in "On This iPad" mode, I can actually see the album there, but it is grayed out, and in the left hand column there is a circle with dotted lines, as if it is an incomplete download--which in essence it is. But I have the album (CD) in my iTunes and on my iPod, just like hundreds of other CD's--what's up with this one?
Another characteristic is that since trying to import this CD into my iPad, I cannot get a successful sync of the iPad now; the syncing process hangs up in "Waiting for changes to be applied" for 3 or 4 minutes, and then it just stops. No message that "The syncing process is complete. Please eject before disconnecting." The sync just quits on its own, so I take it that the syncing process was unsuccessful.
Now what?
Message was edited by: PadretimoteoMake sure that your music is in the format supported by the iPhone. I use either MP3 or AAC.
A friend had the same problem a while back. All his music was in the WMA format and is therefore not playable on the iPhone and would not copy. Once he converted his songs to MP3 they copied to his iPhone without problem. -
my sound has stopped working i have speakers plugged in but computer doesnt register or recognize them. the volume is on mute and grayed out ...will not let me change,what can i do to fix this problem....i have tried unplugging and plugging back in and reset and headphones...nothing works..how do i get my sound back?
OS X Mountain Lion: If you can’t hear sound from your speakers
Read the "If you’re trying to listen through external speakers" section. -
I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?
You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
with your computer. Insert the disc into the optical drive and restart the computer.
After the chime press and hold down the "C" key. Release the key when you see
a small spinning gear appear below the dark gray Apple logo.
2. After the installer loads select your language and click on the Continue
button. When the menu bar appears select Disk Utility from the Utilities menu.
After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
size.) Click on the Partition tab in the DU main window. Set the number of
partitions to one (1) from the Partitions drop down menu, click on Options button
and select GUID, click on OK, then set the format type to MacOS Extended
(Journaled, if supported), then click on the Apply button.
3. When the formatting has completed quit DU and return to the installer. Proceed
with the OS X installation and follow the directions included with the installer.
4. When the installation has completed your computer will Restart into the Setup
Assistant. After you finish Setup Assistant will complete the installation after which
you will be running a fresh install of OS X. You can now begin the update process
by opening Software Update and installing all recommended updates to bring your
installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1. -
I just upgraded to Lion 10.7.2 and it says that it will not support Power PC programs and has blanked out my 2008 version of MS Office for Mac and Intuit's Quickbooks. How do I proceed to get these programs back?
Upgrade to newer versions compatible with Lion or downgrade to Snow Leopard:
Downgrade Lion to Snow Leopard
1. Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Quit DU and return to the installer. Install Snow Leopard.
This will erase the whole drive so be sure to backup your files if you don't have a backup already. If you have performed a TM backup using Lion be aware that you cannot restore from that backup in Snow Leopard (see below.) I suggest you make a separate backup using Carbon Copy Cloner 3.4.1.
If you have Snow Leopard Time Machine backups, do a full system restore per #14 in Time Machine - Frequently Asked Questions. If you have subsequent backups from Lion, you can restore newer items selectively, via the "Star Wars" display, per #15 there, but be careful; some Snow Leopard apps may not work with the Lion files. -
my iphone 5 screen has gone black in the middle of updating a app. i have tried to back it up using itunes and restore it however it will not restore my phone as i have got the app find my iphone switched on. i cannot turn it off as the screen is black. can anyone help me please??
christobell86 wrote:
... it will not restore my phone as i have got the app find my iphone switched on.
You can access iCloud.com on a computer to turn it off.
http://support.apple.com/kb/PH2702
Maybe you are looking for
-
I've had this 13 Inch Macbook Pro complete with the Lion since October 2011. I've been having trouble with the internet connection. I keep getting 'unable to connect to the internet' or 'website unavaiable'. We have a brand new router, so we know for
-
Sound Stuttering in Windows 7 - Please Help
Hello there, I hope you can help?! Ever since I bought my P6320UK HP Pavilion Desktop i have been having intermittent issues playing sound. The audio stops and starts and is distorted. I have gone down every available avenue, been in touch with HP, P
-
HTML, images, links in email signatures
I am trying to add hyperlinks to website addresses inside my email signature. I am also trying to add a Skype status button to my email signature. You can see the code it generates from this page: http://www.skype.com/share/buttons/wizard.html I have
-
New Skype doesn't work with my setup
Nice. I just paid for a Skype number only to find I am locked out of 6.3 version. LISTEN JERKS! I CAN'T USE VERSION 7 WITH PRETTY MAY CALL CENTER SO SKYPE IS USELESS NOW. Enjoy never getting my business again!
-
Focus box anomoly (continued from prior IE alpha issue)
The "standard" PNG fix for IE doesn't work when there are JavaScript image swaps on the page. The "Fix" for it causes the transparent background to 'flash white' for a second as the image loads. Anyone know of any other fixes? Here's an example. http