Cisco APs not joining WLC

Hi guys,
I am in the process of configuring a WLC and got stuck due to APs are not joining the WLC.
I have configure DHCP server on the Gateway router and the WLC management interface is pointing to the Gateway as DHCP Server.
I have multiple Dynamic interfaces configured on the WLC and Interface group has been configured and mapped to Management Interface.
For each WLAN, a separate DHCP pool has been created on the router.
LAG has been configured and working fine. Connectivity works fine in the network and I can ping all devices and vlans from WLC.
Now, the APs are not joining the WLC. The error I am getting
" 44:03:a7:f1:b4:40 Received a Discovery Request from 44:03:A7:F1:B4:40 via IP broadcast address but the source IP address (10.xx.xx.xx) is not in any of the configured subnets. Dropping it "
Some one help me troubleshooting this issue with DHCP IP Assignment.
Thanks,
CJ

If you are using Broadcast method to discover WLC to AP then you need to ensure following is correctly configured.
1. Unders the switch SVI defined for AP-management (10.38.11.x) you have to configure "ip helper-address "
2. In switch global config "ip forward-protocol udp 5246"
Refer this for more detail
http://mrncciew.com/2013/05/04/wlc-discovery-via-broadcast/
There are other methods available as well (static, DNS, DHCP option 43) for the WLC discovery purpose. To verify there is no configuration issues at WLC end, you can simply configure the WLC details on AP statically & check wether AP get register to WLC. To do this you can enter following CLI commands on AP console priviledge mode.
debug capwap console cli
capwap ap ip address 10.38.11.x 255.255.255.x
capwap ap ip default-gateway 10.38.11.y
capwap ap controller ip address
In this way your AP should get registered to WLC (if no config issue at WLC end). Refer this for more detail
http://mrncciew.com/2013/03/17/ap-registration/
If you have so many APs, then as Steve pointed configuring DHCP-Option 43 would be a good option
Regards
Rasika
**** Pls rate all useful responses ****

Similar Messages

  • APs not joining WLC

    Hello community,
    I hope you can help me with my problem.
    I have a vWLC Firmware version: 7.4.121.0, I have also Aironet 1700Aps
    I have successfully configured wlc with service and management interface. In the management network I can ping the vWLC managenemt interface as well the APs in this network. The firewall is also the DHCP Server for the management network. (It is working because APs get an IP address) The problem is the APs are not joining the vWLC. This is my first time I use WLC and APs. So they are completely new and not used before.
    Here is the debug output of vWLC:
    ApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 Finding DTLS connection to delete for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 Disconnecting DTLS Capwap-Ctrl session 0x8faa580 for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.997: 84:80:2d:bd:fa:10 CAPWAP State: Dtls tear down
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 DTLS connection closed event receivedserver (192:168:200:3/5246) client (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 Entry exists for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:07.998: 84:80:2d:bd:fa:10 No AP entry exist in temporary database for 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.004: 84:80:2d:bd:fa:1e DTLS connection not found, creating new connection for 192:168:200:10 (57250) 192:168:200:3 (5246)
    *spamApTask4: Feb 11 16:31:08.472: 84:80:2d:bd:fa:1e DTLS Session established server (192.168.200.3:5246), client (192.168.200.10:57250)
    *spamApTask4: Feb 11 16:31:08.472: 84:80:2d:bd:fa:1e Starting wait join timer for AP: 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Join Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:1e Deleting AP entry 192.168.200.10:57250 from temporary database.
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Finding DTLS connection to delete for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 Disconnecting DTLS Capwap-Ctrl session 0x8faa720 for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.477: 84:80:2d:bd:fa:10 CAPWAP State: Dtls tear down
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 DTLS connection closed event receivedserver (192:168:200:3/5246) client (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 Entry exists for AP (192:168:200:10/57250)
    *spamApTask4: Feb 11 16:31:08.479: 84:80:2d:bd:fa:10 No AP entry exist in temporary database for 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.515: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 11 16:31:08.516: 84:80:2d:bd:fa:10 Discovery Response sent to 192.168.200.10:57250
    *spamApTask0: Feb 11 16:31:08.516: 84:80:2d:bd:fa:1e Received LWAPP DISCOVERY REQUEST to 40:4a:03:79:d7:20 on port '1'
    *spamApTask0: Feb 11 16:31:08.516: 84:80:2d:bd:fa:1e Discarding discovery request in LWAPP from AP supporting CAPWAP
    Sadly I don`t have a debuging cable for the APs. Therefore I have no debuging output of the APs. (It is ordered ;-) )
    But I hope the output of the APs is right now not important to solve this problem.
    Thank you
    //EDIT
    On the firewall are no ports blocked

    Okay I upgraded the vWLC to 8.0.110.0.
    I looked in the event log of the vWLC. It was successfully discovered and also the new image version was send to the AP.
    Sadly the Ap does not join to the vWLC.
    *apfReceiveTask: Feb 12 09:53:35.640: WARP IEs: (12)
    *apfReceiveTask: Feb 12 09:53:35.640:      [0000] dd 0a 00 c0 b9 01 00 00 00 08 01 01
    *apfReceiveTask: Feb 12 09:53:35.640: Wlan Feature status 0 for  AP:84:80:2d:45:75:e0 (slotID 1)
    *apfReceiveTask: Feb 12 09:53:35.640: Split tunnel status (Disabled) encoded in the vap payload for WLAN(1), AP:84:80:2d:45:75:e0 (slotID 1)
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Configuration Status from 192.168.200.10:57251
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 CAPWAP State: Configure
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Updating IP info for AP 84:80:2d:45:75:e0 -- static 0, 192.168.200.10/255.255.255.0, gtw 192.168.200.3
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Updating IP 192.168.200.10 ===> 192.168.200.10 for AP 84:80:2d:45:75:e0
    *spamApTask5: Feb 12 09:53:35.789: 84:80:2d:45:75:e0 Invalid length (9) countedlen 6 sizeUserPayload 277 for vendor-specific element 0x00409600-unknown (185) from AP  84:80:2D:45:75:E0
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Setting MTU to 1485
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Finding DTLS connection to delete for AP (192:168:200:10/57251)
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 Disconnecting DTLS Capwap-Ctrl session 0xb947000 for AP (192:168:200:10/57251)
    *spamApTask5: Feb 12 09:53:35.790: 84:80:2d:45:75:e0 CAPWAP State: Dtls tear down
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 DTLS connection closed event receivedserver (192.168.200.3/5246) client (192.168.200.10/57251)
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 Entry exists for AP (192.168.200.10/57251)
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 0
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 apfSpamProcessStateChangeInSpamContext: Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 1
    *spamApTask5: Feb 12 09:53:35.791: update ap status:84:80:2d:45:75:e0 ,index:60
    *spamApTask5: Feb 12 09:53:35.791: 84:80:2d:45:75:e0 No AP entry exist in temporary database for 192.168.200.10:57251
    *apfReceiveTask: Feb 12 09:53:35.792: 84:80:2d:45:75:e0 Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 0
    *apfReceiveTask: Feb 12 09:53:35.792: 84:80:2d:45:75:e0 Deregister LWAPP event for AP 84:80:2d:45:75:e0 slot 1
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 12 09:53:35.918: apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.918: apType = 45 apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10 port 57250
    *spamApTask4: Feb 12 09:53:35.918: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Request from 192.168.200.10:57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 200, joined Aps =0
    *spamApTask4: Feb 12 09:53:35.919: apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.919: apType = 45 apModel: AIR-CAP702I-C-K9
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10 port 57250
    *spamApTask4: Feb 12 09:53:35.919: 84:80:2d:45:75:e0 Discovery Response sent to 192.168.200.10:57250
    Sadly I don`t understand what this debugging log says :-(
    Maybe you can help me again
    Thank you
    //SOLUTION -----------------------------------------------------------------------------------------------------------------------------------------------------------
    I found something on the internet, but for all people having also this problem here is the solution:
    Change the country of your vWLC. Right now I am in China, so I changed it and then it was working flawlessly :-)
    Step 1  
    Disable the 802.11 networks as follows:
    Choose Wireless > 802.11a/n > Network.
    Unselect the 802.11a Network Status check box.
    Click Apply.
    Choose Wireless > 802.11a/n > Network.
    Unselect the 802.11b/g Network Status check box.
    Click Apply.
    Step 2  
    Choose Wireless > Country to open the Country page.
    Thank you all for your help :-)
    Paul

  • APs not joining controller errors

    I keep getting errors on different APs not joining controllers:
    Jan  5 15:54:40.097: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Jan  5 15:54:40.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.x.x.x peer_port: 5246
    *Jan  5 15:54:40.001: %CAPWAP-5-CHANGED: CAPWAP changed state to 
    *Jan  5 15:54:41.778: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.x.x.x  peer_port: 5246
    *Jan  5 15:54:41.780: %CAPWAP-5-SENDJOIN: sending Join Request to 10.x.x.x
    *Jan  5 15:54:41.780: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Jan  5 15:54:41.787: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.x.x.x
    *Jan  5 15:54:41.788: %DTLS-5-PEER_DISCONNECT: Peer 10.x.x.x  has closed connection.
    *Jan  5 15:54:41.788: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.x.x.x :5246.
    Any ideas?  I'm not sure why the peer is disconnecting the connection.  The controller that is linked to It happens on 1242 and 1231 APs mostly.  I've had it happen on a 1142 and 1252 once, but after a reboot it joined fine.
    I'm running 6.0.188.0 on 6 WISMs.  The ap-manager that these APs keep trying to join only has 5 APs on it.

    Can you get a sniffer trace of the port-channel to one of the WiSM, and if possible, the console of the AP?  Also, check the MAC address of the AP(s) that are not joining to see if they start with something other than 00:, you may also want to check the MAC of the gw for those AP for the same thing.
    The defect I'm thinking of is CSCte01087

  • Cisco APs not updating after WLC-update

    Hello everyone,
    I need to update my 5508 WLCs to a newer software, to support new AP-models.
    Started with AIR-CT5500-K9-1-7-0-0-FUS.aes and AIR-CT5500-K9-7-0-240-0.aes, everything worked fine. Pre-Downloaded the newer Image to the APs, restarted the WLCs and everything was ok.
    Now I tried to update to 7.6.100.0 as well as 7.4.121.0. Both Versions should support my APs, but it doesn't work at all.
    Any ideas are highly appreciated.
    If you need further output, just let me know.
    Regards,
    Manuel
    These are some informations about the environment, AP-info and logging after "upgrade" to 7.4.121.0, controller-information after downgrading again...
    AP#  sh ver
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA7, RELEASE SOFTWARE (fc1)
    ROM: Bootstrap program is C1240 boot loader BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    AP uptime is 1 minute System returned to ROM by power-on System image file is "flash:/c1240-k9w8-mx.124-23c.JA7/c1240-k9w8-mx.124-23c.JA7"
    cisco AIR-LAP1242AG-E-K9  (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
    Processor board ID FCZ1545812F
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on LWAPP image version 7.0.240.0
    1 FastEthernet interface
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 70:CA:9B:07:86:B8
    Part Number                          : 73-10256-07
    PCA Assembly Number                  : 800-26918-06
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC15402NP4
    Top Assembly Part Number            : 800-29152-03
    Top Assembly Serial Number          : FCZ1545812F
    Top Revision Number                  : A0
    Product/Model Number                : AIR-LAP1242AG-E-K9
    Configuration register is 0xF
    AP#dir
    Directory of flash:/
    2  -rwx      89311  Jan 18 2014 20:41:00 +00:00  event.log
    3  drwx          64  Jan 18 2014 20:43:21 +00:00  update
    5  drwx        256  Jan 18 2014 20:40:55 +00:00  c1240-k9w8-mx.124-23c.JA7
    4  -rwx        6168  Nov 2 2011 23:32:18 +00:00  private-multiple-fs
    7  -rwx        395  Mar 1 2002 00:00:05 +00:00  env_vars
    15740928 bytes total (8772096 bytes free)
    AP#dir
    Directory of flash:/c1240-k9w8-mx.124-23c.JA7/
    9  -rwx      131328  Jan 18 2014 20:39:46 +00:00  7101.img
    10  -rwx        292  Jan 18 2014 20:39:46 +00:00  info
    11  -rwx    4642714  Jan 18 2014 20:40:55 +00:00  c1240-k9w8-mx.124-23c.JA7
    15  -rwx      131328  Jan 18 2014 20:40:56 +00:00  6701.img
    #sh logging --> see attached file
    CONTROLLER (unfortunately after downgrading it again):
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.0.240.0
    Bootloader Version............................... 1.0.16
    Field Recovery Image Version..................... 7.0.112.21
    Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
    Build Type....................................... DATA + WPS
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    IP Address....................................... WLC-IP
    Last Reset....................................... Software reset
    System Up Time................................... 0 days 0 hrs 26 mins 3 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin, Rome, Vienna Current Boot
    License Level....................... base
    Current Boot License Type........................ Permanent
    Next Boot License Level.......................... base
    Next Boot License Type........................... Permanent
    Configured Country............................... DE  - Germany
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 2
    Number of Active Clients......................... 5
    Burned-in MAC Address............................ 1C:DF:0F:C6:D8:80
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Absent
    Maximum number of APs supported.................. 150
    (Cisco Controller) >show boot
    Primary Boot Image............................... 7.4.121.0
    Backup Boot Image................................ 7.0.240.0 (default) (active)
    (Cisco Controller) >show ap bundle primary
    Primary AP Image        Size
    ap1g2                  9576
    ap3g1                  6684
    ap3g2                  11208
    ap801                  5192
    ap802                  5232
    c1100                  3096
    c1130                  4972
    c1140                  4992
    c1200                  3364
    c1240                  4812
    c1250                  5512
    c1310                  3136
    c1520                  6412
    c3201                  4324
    c602i                  3716
    (Cisco Controller) >show ap bundle secondary
    Secondary AP Image      Size
    ap3g1                  6684
    ap801                  5192
    ap802                  5232
    c1100                  3096
    c1130                  4972
    c1140                  4992
    c1200                  3364
    c1240                  4812
    c1250                  5512
    c1310                  3136
    c1520                  6412
    c3201                  4324
    c602i                  3716
    Nachricht geändert durch Manuel Sporleder

    Hi Scott,
    I am not trying to pre-download it anymore, since this doesn't work at all.
    If I just restart the controller, the APs are downloading the image telling me "everything is fine", are rebooted and that stated with the old image again.
    This is what you can see in the attached log-file:
    *Mar  1 00:00:05.873: soap_prepare_new_image_crash: mini ios flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
    *Mar  1 00:00:06.242: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.662: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.054: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:09.152: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:09.181:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:11.381: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:11.440: %SYS-5-RESTART: System restarted
    *Mar  1 00:00:11.441: %SNMP-5-COLDSTART: SNMP agent on host AP is undergoing a cold start
    *Nov  2 23:31:59.107: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Nov  2 23:31:59.108: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Nov  2 23:31:59.929: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Nov  2 23:32:00.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Nov  2 23:32:00.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Nov  2 23:32:18.102: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Nov  2 23:32:18.163: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
    *Nov  2 23:32:18.345: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Nov  2 23:32:18.759:  status of voice_diag_test from WLC is false
    *Nov  2 23:32:18.847: Logging LWAPP message to 255.255.255.255.
    *Nov  2 23:32:33.181: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Nov  2 23:32:33.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Nov  2 23:32:34.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Nov  2 23:32:34.213: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Jan 20 20:32:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: WLC-1-IP peer_port: 5246
    *Jan 20 20:32:44.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Jan 20 20:32:45.479: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: WLC-1-IP peer_port: 5246
    *Jan 20 20:32:45.480: %CAPWAP-5-SENDJOIN: sending Join Request to WLC-1-IP
    *Jan 20 20:32:45.481: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Jan 20 20:32:45.484: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from WLC-1-IPperform archive download capwap:/c1240 tar file
    *Jan 20 20:32:45.494: %CAPWAP-5-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
    *Jan 20 20:32:45.499: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE
    *Jan 20 20:33:58.755: %DTLS-3-BAD_RECORD: Erroneous record received from WLC-1-IP: Duplicate (replayed) record
    *Jan 20 20:33:59.315: image upgrade successfully, system is now reloading
    This happens again and again and again...
    Regards, Manuel

  • 3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN

    Hi Guys, 
    This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
    Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC. 
    if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
    it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
    please see below for the boot up of the AP and the WLC logs: 
    AP 
    IIOS Bootloader - Starting system.
    *** deleted for breverity ***** 
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    *** deleted for breverity ***** 
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  *** deleted for breverity ***** 
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    WLC: 
    isco Controller) >show time
    Time............................................. Tue Jan 27 17:44:47 2015
    Timezone delta................................... 0:0
    Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
    NTP Servers
        NTP Polling Interval.........................     3600
         Index     NTP Key Index                  NTP Server                  NTP Msg Auth Status
           1              0                             150.101.176.226       AUTH DISABLED
    (Cisco Controller) >show ap join stats summary  
    Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
    (Cisco Controller) >show ap join stats summary all 
    Number of APs.............................................. 2 
    Base Mac             AP EthernetMac       AP Name                 IP Address         Status
    f4:4e:05:aa:a6:a0    f4:4e:05:94:c3:98    APf44e.0594.c398        10.1.1.22          Joined    
    f4:4e:05:b6:ce:f0    N A                  Test_1                  10.1.20.7          Not Joined
    (Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
    Sync phase statistics
    - Time at sync request received............................ Not applicable
    - Time at sync completed................................... Not applicable
    Discovery phase statistics
    - Discovery requests received.............................. 45
    - Successful discovery responses sent...................... 21
    - Unsuccessful discovery request processing................ 24
    - Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
    - Time at last successful discovery attempt................ Jan 27 17:45:49.705
    - Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
    Join phase statistics
    - Join requests received................................... 0
    - Successful join responses sent........................... 0
    - Unsuccessful join request processing..................... 0
    - Reason for last unsuccessful join attempt................ Not applicable
    - Time at last successful join attempt..................... Not applicable
    - Time at last unsuccessful join attempt................... Not applicable
    Configuration phase statistics
    --More-- or (q)uit
    - Configuration requests received.......................... 0
    - Successful configuration responses sent.................. 0
    - Unsuccessful configuration request processing............ 0
    - Reason for last unsuccessful configuration attempt....... Not applicable
    - Time at last successful configuration attempt............ Not applicable
    - Time at last unsuccessful configuration attempt.......... Not applicable
    Last AP message decryption failure details
    - Reason for last message decryption failure............... Not applicable
    Last AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
    - Last AP disconnect reason................................ Not applicable
    Last join error summary
    - Type of error that occurred last......................... Lwapp discovery request rejected
    - Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
    - Time at which the last join error occurred............... Jan 27 17:45:49.705
    AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
                                                                               Ethernet Mac : 00:00:00:00:00:00  Ip Address : 10.1.20.7
    (Cisco Controller) >show interface summary 
     Number of Interfaces.......................... 4
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap                               LAG  20       10.1.20.231     Dynamic No     No   
    guest                            LAG  30       10.1.30.231     Dynamic No     No   
    management                       LAG  10       10.1.1.231      Static  Yes    No   
    virtual                          N/A  N/A      1.1.1.1         Static  No     No   
    SWITCH
    witch#show run
    Building configuration...
    *** deleted for breverity ***** 
    no aaa new-model
    clock timezone AWST 8
    system mtu routing 1500
    ip routing
    ip dhcp pool WAP_Pool
       network 10.1.20.0 255.255.255.0
       default-router 10.1.20.1 
       option 43 hex f104.0a01.01e7
    ip dhcp pool Clients
       network 10.1.30.0 255.255.255.0
       default-router 10.1.30.1 
       dns-server 203.0.178.191 
    ip dhcp pool test
       network 10.1.1.0 255.255.255.0
       default-router 10.1.1.1 
    crypto pki trustpoint TP-self-signed-4082587776
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-4082587776
     revocation-check none
     rsakeypair TP-self-signed-4082587776
    *** deleted for breverity ***** 
    *** deleted for breverity ***** !
    interface FastEthernet0/3
     description *** WLC ****
     switchport trunk encapsulation dot1q
     switchport mode trunk
    interface FastEthernet0/4
     description **** AP *****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/5
     description **** AP ****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/6
    i*** deleted for breverity ***** !
    interface Vlan10
     description *** Managment ***
     ip address 10.1.1.230 255.255.255.0
    interface Vlan20
     description *** WIRELESS APS ***
     ip address 10.1.20.1 255.255.255.0
    interface Vlan30
     ip address 10.1.30.1 255.255.255.0
    ip classless
    ip route 0.0.0.0 0.0.0.0 10.1.1.1
    ip http server
    ip http secure-server
    ip sla enable reaction-alerts
    l*** deleted for breverity ***** 
    ntp clock-period 36028827
    ntp source FastEthernet0/1
    ntp server 121.0.0.42
    ntp server 202.127.210.37
    end
    I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working. 
    Thanks 

    Hey Scott, 
    I gave that a shot and still no luck, log's from AP boot up:
    IIOS Bootloader - Starting system.
    flash is writable
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 20 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 21 seconds.
    flashfs[1]: 0 files, 1 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 12257280
    flashfs[1]: Bytes used: 1024
    flashfs[1]: Bytes available: 12256256
    flashfs[1]: flashfs fsck took 1 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Initializing flashfs...
    flashfs[2]: 67 files, 9 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 40900608
    flashfs[2]: Bytes used: 20894208
    flashfs[2]: Bytes available: 20006400
    flashfs[2]: flashfs fsck took 14 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 0 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 650 entries (20 legacy/224 11n/406 11ac)
    POWER TABLE FILENAME = ram:/Q2.bin
    Radio1  present 8864 8000 0 80000000 80100000 4
    POWER TABLE FILENAME = ram:/Q5.bin
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP

  • AP not joining WLC 2504

    Hi all
    my customer has a 2504 WLC, and has problems to join APs (There are no aps joined to the controller at this moment).
    What are the Bold lines tell me?
    in the debug I see the following:
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 Discovery Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 ApModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.019: 58:f3:9c:78:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 50, 0
    *spamApTask0: Oct 10 09:20:06.019: apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.020: apType = 38 apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.020: Unknown AP type. Using Controller Version!!!
    *spamApTask0: Oct 10 09:20:06.020: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116 port 41508
    *spamApTask0: Oct 10 09:20:06.020: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 ApModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Join Priority Processing status = 0, Incoming Ap's Priority 4, MaxLrads = 50, 0
    *spamApTask0: Oct 10 09:20:06.021: apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: apType = 38 apModel: AIR-CAP3702I-N-K9
    *spamApTask0: Oct 10 09:20:06.021: Unknown AP type. Using Controller Version!!!
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116 port 41508
    *spamApTask0: Oct 10 09:20:06.021: 58:f3:9c:78:d1:10 Discovery Response sent to 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.031: 58:f3:9c:7a:22:30 DTLS connection not found, creating new connection for 10:37:24:116 (41508) 10)
    *spamApTask0: Oct 10 09:20:16.498: acDtlsPlumbControlPlaneKeys: lrad:10.37.24.116(41508) mwar:10.37.24.11(5246)
    *spamApTask0: Oct 10 09:20:16.498: 58:f3:9c:7a:22:30 Allocated index from main list, Index: 55
    *spamApTask0: Oct 10 09:20:16.498: 58:f3:9c:7a:22:30 Using CipherSuite AES128-SHA
    *spamApTask0: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 DTLS keys for Control Plane are plumbed successfully for AP 10.37.24.116. Inde6
    *spamApTask1: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 DTLS Session established server (10.37.24.11:5246), client (10.37.24.116:41508)
    *spamApTask1: Oct 10 09:20:16.499: 58:f3:9c:7a:22:30 Starting wait join timer for AP: 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.517: 58:f3:9c:78:d1:10 Join Request from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.517: 58:f3:9c:7a:22:30 Deleting AP entry 10.37.24.116:41508 from temporary database.
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 spamProcessJoinRequest : RAP, Check MAC filter
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 In AAA state 'Idle' for AP 58:f3:9c:78:d1:10
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 Mesh AP username 58f39c7a2230.
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 Join Request failed!
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:78:d1:10 State machine handler: Failed to process  msg type = 3 state = 0 from 10.37.248
    *spamApTask0: Oct 10 09:20:16.518: 58:f3:9c:7a:22:30 Failed to parse CAPWAP packet from 10.37.24.116:41508
    *spamApTask0: Oct 10 09:20:16.519: XóxÑ
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 Finding DTLS connection to delete for AP (10:37:24:116/41508)
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 Disconnecting DTLS Capwap-Ctrl session 0x179437d8 for AP (10:37:24:116/41508)
    *spamApTask0: Oct 10 09:20:16.519: 58:f3:9c:78:d1:10 CAPWAP State: Dtls tear down
    *spamApTask0: Oct 10 09:20:16.520: acDtlsPlumbControlPlaneKeys: lrad:10.37.24.116(41508) mwar:10.37.24.11(5246)
    *spamApTask0: Oct 10 09:20:16.520: 58:f3:9c:78:d1:10 DTLS keys for Control Plane deleted successfully for AP 10.37.24.116
    *spamApTask0: Oct 10 09:20:16.526: 58:f3:9c:78:d1:10 DTLS connection closed event receivedserver (10.37.24.11/5246) client (10.37.2)
    *spamApTask0: Oct 10 09:20:16.526: 58:f3:9c:78:d1:10

    Hi all, the AP was in Mesh (Bridge) mode and could not connect to the controller
    Ok, how to find out that a AP is in bridge mode, without a join (No Access to the AP).
    go to monitor > statistics > AP Join
    you will see the AP here that tries to connect (clear the list before)
    if the ethernet MAC Address is the same as the Base radio MAC, than the AP is in bridge mode.
    normally ( in local mode) the Ethernet MAC Address reflects the APname
    To allow the AP to join, add in the Authorization list the APName mac Address!
    See: http://supertekboy.com/2014/01/13/cisco-lightweight-access-point-will-not-join-to-a-wireless-lan-controller/
    The case is solved now.

  • AP not joining WLC b/c of DHCP.

    This is the first time that I've dealt with a WLC, so I'm trying to do a real simple setup. I have a WLC 2106 and a few LAP 1141N's. I'm trying to set them up on a single VLAN, no RADIUS server, and I want my router to handle DHCP (not the WLC). Here's the info I setup the WLC with:
    Welcome to the Cisco Wizard Configuration Tool
    Use the '-' character to backup
    System Name [Cisco_94:40:40]: WLC
    Enter Administrative User Name (24 characters max): cisco
    Enter Administrative Password (24 characters max): *****
    Management Interface IP Address: 192.168.3.5
    Management Interface Netmask: 255.255.255.0
    Management Interface Default Router: 192.168.3.1
    Management Interface VLAN Identifier (0 = untagged): 0
    Management Interface Port Num [1 to 4]: 1
    Management Interface DHCP Server IP Address: 192.168.3.1
    AP Manager Interface IP Address: 192.168.3.6
    AP-Manager is on Management subnet, using same values
    AP Manager Interface DHCP Server (192.168.3.1):
    Virtual Gateway IP Address: 1.1.1.1
    Mobility/RF Group Name: GroupRF
    Network Name (SSID): Test
    Allow Static IP Addresses [YES][no]: yes
    Configure a RADIUS Server now? [YES][no]: no
    Warning! The default WLAN security policy requires a RADIUS server.
    Please see documentation for more details.
    Enter Country Code (enter 'help' for a list of countries) [US]: US
    Enable 802.11b Network [YES][no]: Yes
    Enable 802.11a Network [YES][no]: no
    Enable 802.11g Network [YES][no]: yes
    Enable Auto-RF [YES][no]: yes
    Configuration saved!
    Resetting system with new configuration...
    When I login to the web interface of the WLC (https://192.168.3.5) it doesn't show any AP's as joining even though I have one plugged in to the WLC. I console'd into the AP and this is the error that keeps on repeating:
    *Mar  1 00:51:45.962: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    Am I missing something? I already checked the WLC, and the date/time is setup correctly. And I know my router (at 192.168.3.1) is handing out DHCP. Everything is on the same subnet so I don't understand why I'm having such a hard time with this. I've tried my hardest searching online but haven't found anything. Any help would REALLY be appreciated. Thank you very much.
    P.S. If you have any other questions please feel free to ask.

    The answer is that LWAPP / CAPWAP APs need to be connected to an access port on a swtich (configured with the proper VLAN) as they do nothing more than pass the traffic to the WLC through the LWAPP / CAPWAP tunnel.  The WLC ethernet ports are configured as trunks and can not be change. This is because the WLC is where all the VLAN tagging takes place. 
    Hope that helps,
    Scott
    Please rate this post if you found it helpful. 

  • APs not joining 5508 on dynamic ports created manualy

    Hey all,
    i have a problem with our new 5508 wireless controller (7.0.116.0).
    Port 1 is the system default "management" (Port 2 is backup). Dynamic AP Management is disabled.
    Port 3 is a new dynamic interface "ap-manager 2" with Dynamic AP Management enabled and has a ip in a seperated VLAN which is not routed.
    When i am connecting the AP (1260 series) to the "ap-manager 2" interface, then it will not join and i get an error message on the WLC:
    *spamApTask1: Mar 05 14:52:12.783: %CAPWAP-3-DISC_INTF_ERR1:
    capwap_ac_sm.c:1453 Ignoring discovery request received on non-management
    interface (3) from AP
    When i am connecting the AP to the "management2 interface, then it is working fine. But i don't want the APs in the Management LAN. I want them in the separated no routed LAN explicit for the APs.
    What do i miss here.
    Thanks a lot.
    Regards
    Matthew

    Hmmm...but i found follwoing in the documentation:
    The AP-manager interface's IP address must be different from the management interface's IP address and may or may not be on the same subnet as the management interface. However, we recommend that both interfaces be on the same subnet for optimum access point association.
    I want the APs in a separated non routed LAN because of security reasons. Why set APs into the management LAN when they only need to communicate with the controller?
    But if there is no way to do that, then i need to redesign the plans for the WLAN structure.
    Thanks
    Matthew

  • AP 1552E NOT JOINING WLC 2504

    Hello,
    I am currently having issue relating to my AP not joining the WLC. Have made the WLC the internal DHCP server and the AP has picked an IP Address but the below is what i get from the AP:
    *Feb 14 22:48:56.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:48:56.759: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Feb 14 22:48:56.783:  status of voice_diag_test from WLC is false
    *Feb 14 22:49:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:12.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:12.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:17.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:17.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:12.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:12.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:12.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:12.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    % CDP is not supported on this interface, or for this encapsulation
    *Feb 14 22:49:17.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:17.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:17.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:17.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:49:17.707: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Feb 14 22:49:17.759: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Feb 14 22:49:17.783:  status of voice_diag_test from WLC is false
    *Feb 14 22:49:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:34.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:34.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:39.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:39.663: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.1.2
    *Feb 14 22:49:39.663: %DTLS-5-PEER_DISCONNECT: Peer 192.168.1.2 has closed connection.
    *Feb 14 22:49:39.663: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.2:5246
    *Feb 14 22:49:34.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 14 22:49:34.663: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.2 peer_port: 5246
    *Feb 14 22:49:34.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2
    *Feb 14 22:49:34.663: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 14 22:49:38.591: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Feb 14 22:49:38.591: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Feb 14 22:49:38.591: %MESH-6-LINK_UPDOWN: Mesh station f029.29c2.effc link Down
    *Feb 14 22:49:39.663: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.2

    Platform: AIR-CT2504-K9, Version :
    Manufacturer's Name: Cisco Systems Inc.  Product Name: Cisco Controller  Product Version: 7.0.220.0  RTOS Version: Erro  Bootloader Version: 1.0.18  Build Type: DATA + WPS
    Platform: cisco AIR-CAP1552E-E-K9  Version :
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
    Proceeding with system init
    Proceeding to unmask interrupts
    Initializing flashfs...
    flashfs[1]: 22 files, 3 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 31610880
    flashfs[1]: Bytes used: 6631936
    flashfs[1]: Bytes available: 24978944
    flashfs[1]: flashfs fsck took 5 seconds.
    flashfs[1]: Initialization complete.
    flashfs[2]: 0 files, 1 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 5806080
    flashfs[2]: Bytes used: 1024
    flashfs[2]: Bytes available: 5805056
    flashfs[2]: flashfs fsck took 1 seconds.
    flashfs[2]: Initialization complete....done Initializing flashfs.
    Warning:  the compile-time code checksum does not appear to be present.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    %Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP1552E-E-K9    (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.
    Processor board ID FCZ1718H01Y
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from power loss
    LWAPP image version 7.0.220.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F0:29:29:C2:EF:E0
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC1705241P
    Top Assembly Part Number             : 800-34853-05
    Top Assembly Serial Number           : FCZ1718H01Y
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552E-E-K9
    % Please define a domain-name first.
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
    Press RETURN to get started!
    *Mar  1 00:00:07.307: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.723: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:09.819: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:09.819: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:11.375: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:11.963: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:12.039: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
    *Mar  1 00:00:12.051: AP identified to be in Fenway/Huck Jr/1240/1130 configuration
    *Mar  1 00:00:12.055:  status of voice_diag_test from WLC is false
    *Mar  1 00:00:14.079: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Tue 18-Oct-11 15:13 by prod_rel_team
    *Mar  1 00:00:14.079: %SNMP-5-COLDSTART: SNMP agent on host APf029.29c2.efe0 is undergoing a cold start
    *Mar  1 00:00:14.143: %MESH-6-BVI_CREATED: Mesh BVI1 interface created
    *Mar  1 00:00:14.163: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:14.163: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:15.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:15.163: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:16.143: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:17.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitE
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)thernet0, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down
    *Mar  1 00:00:17.143: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down
    *Mar  1 00:00:18.579: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:20.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:32.743: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:32.795: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:32.959: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:33.107: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:33.307: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Mar  1 00:00:46.383: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960-24PC-S (189c.5d95.2d18)
    Username:
    *Mar  1 00:01:27.119: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    Username:
    *Mar  1 00:01:32.163: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:01:34.119: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:01:35.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:01:37.207: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    % CDP is not supported on this interface, or for this encapsulation
    *Mar  1 00:01:40.887: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:01:40.907:  status of voice_diag_test from WLC is false
    *Mar  1 00:01:46.387: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C2960-24PC-S (189c.5d95.2d18)
    Regards,
    Obinna Samuel

  • 1131 LWAP not join WLC 4402

    I am deploying WLC 4402 with LWAP 1131 but AP fail to join the WLC .The resone that I dont have DNS server.The error message in the AP is :
    AP001d.451f.8582>
    *Mar 1 00:00:38.005: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned D
    HCP address 172.26.5.12, mask 255.255.255.0, hostname AP001d.451f.8582
    Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
    *Mar 1 00:00:49.371: LWAPP_CLIENT_ERROR: lwapp_name_lookup - Could Not resolve
    I tried to configure the Controller address in LAP but I fail ,The error when I tried to configure AP is below:
    AP001d.451f.8582#lwapp ap controller ip address 172.26.5.10
    ERROR!!! Command is disabled.
    my question is :
    is it possible to make LAP join WLC with out DNS,if yes how ?

    Hi Yhab,
    There are other ways besides DNS to help in the AP and WLC Discovery process. Have a look in this good doc;
    Lightweight AP (LAP) Registration to a Wireless LAN Controller (WLC)
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml#topic2
    For the Static entry problem;
    If this AP was ever registered you can use this command from the LAP CLI to clear the LWAPP configuration on the LAP:
    clear lwapp private-config
    This allows you to use the AP LWAPP static configuration commands again.
    Here is an example:
    Enable (enter password)
    AP1240#clear lwapp private-config
    AP1240#lwapp ap hostname AP1240
    AP1240#lwapp ap ip address 10.77.244.199 255.255.255.224
    AP1240#lwapp ap ip default-gateway 10.77.244.220
    AP1240#lwapp ap controller ip address 172.16.1.50
    Note: You cannot use the clear lwapp private-config command when the LAP is registered with the controller.
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a00808e2d27.shtml#t2
    Hope this helps!
    Rob

  • Access Points not joining WLC

    Hello All,
    I am trying to deploy several AIR-CAP3502E-E-K9 access points from a cisco 5508 wire lan contoller running ver 7 code. However iam having difficulty regiserting the access points with the WLC. The wlc is connect to a 3650 switch, and each access point is connected to a 2960 switch.
    Problem Solved. A bad update was not allowing the access points to get their correct firmware.

    You need to provide what Leo stated, that would help a lot. Anyways you can't telnet or ssh into a capwap AP if it has not joined the WLC. So that being said, provide the info Leo requested and then console into the ap and provide use with output from the console. Make sure you reboot the AP and then start capturing the output for around 5 minutes.
    Sent from Cisco Technical Support iPad App

  • AP not joining WLC

    Hello
    I am running WLC4404 image 6.0 the latest one. the AP is not joining the controller and it is saying invalid license in configuration request.
    This is a boot of one of the access point:
    Dec 11 11:05:59.025: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Dec 11 11:05:59.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.140.248 peer_port: 5246
    *Dec 11 11:05:59.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Dec 11 11:06:02.862: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.140.248 peer_port: 5246
    *Dec 11 11:06:02.863: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.140.248
    *Dec 11 11:06:02.863: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Dec 11 11:06:03.619: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *Dec 11 11:06:03.764: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.140.248
    *Dec 11 11:06:03.764: %DTLS-5-PEER_DISCONNECT: Peer 172.16.140.248 has closed connection.
    *Dec 11 11:06:03.764: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 172.16.140.248:5246
    *Dec 11 11:06:03.803: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Dec 11 11:06:03.803: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Dec 11 11:06:13.824: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Dec 11 11:06:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.140.248 peer_port: 5246
    *Dec 11 11:06:14.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Dec 11 11:06:18.644: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.140.248 peer_port: 5246
    *Dec 11 11:06:18.644: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.140.248
    *Dec 11 11:06:18.644: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Dec 11 11:06:19.587: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *Dec 11 11:06:19.722: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.140.248
    *Dec 11 11:06:19.722: %DTLS-5-PEER_DISCONNECT: Peer 172.16.140.248 has closed connection.
    *Dec 11 11:06:19.722: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 172.16.140.248:5246
    *Dec 11 11:06:19.761: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Dec 11 11:06:19.761: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    Any advise,
    Elie

    Hi Elie,
    As it looks like the AP is closing the DTLS connection:
    ~
    *Dec 11 11:06:03.764: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.140.248
    ~
    I would also suggest to connect to the AP through the serial console and collect the output there during the boot/join process.
    In regard to the the WLC debugs I would also add the "debug pm pki enable", so to further troubleshoot certificate related issues.
    I hope this helps.
    Regards,
    Federico

  • Cisco 7925 not joining WLAN Network

    hi
    I have one 7925G-E phone, 1142-E LAP & WLC 5508 & CME 71. in a 3900 router. I am trying to join the phone with  CME but the
    phone is not joining the WLAN network.
    showing error msg connection failed, i have tried with WEP, Open, Open+WEP option on the phone and WLC but still facing problem,.
    Thanks
    Saurav
    I have tried with WPA-PSK and tried the notebook to join it is joining but the Phone is not joiining getting the same error.
    connection failed.
    *May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:27:36.856: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:27:36.855: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May  02 15:18:32.227: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could  not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN  requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac,  SSID:voip,AP: c4:7d:4f:4b:a4:40.
    *May 02 15:18:32.082:  %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the  RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA  and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP:  c4:7d:4f:4b:a4:40.
    *May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May  02 15:16:24.677: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW:  apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of  WLANs from 6(cisco_test) to 7(voip)
    *May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May  02 15:14:20.567: %APF-3-SET_VAP_STATUS_FAILED: apf_api.c:15464 Could  not Set the Status of Virtual Access point Entry.Encryption mode for  static WEP does not match encryption mode for dynamic WEP on WLAN.Static  WEP:1.Dynamic WEP:2. WLAN:'voip'
    *May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:08:45.134: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:08:45.133: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:08:45.131: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:08:45.130: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May  02 15:08:43.623: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW:  apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of  WLANs from 4(CGC-7FL-WLAN) to 6(cisco_test)
    *May 02 15:07:35.339:  %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting  mobile 00:21:6b:39:a1:ac due to switch of WLANs from 7(voip) to  4(CGC-7FL-WLAN)
    *May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED:  localeap_db.c:2716 Unable to add method 'peap' to EAP profile for user  'test'. method already exist.
    *May 02 15:06:55.072:  %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method  'tls' to EAP profile for user 'test'. method already exist.
    *May 02  15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to  add method 'fast' to EAP profile for user 'test'. method already exist.
    *May  02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable  to add method 'leap' to EAP profile for user 'test'. method already  exist.
    *May 02 15:06:27.672: %DOT1X-3-MAX_EAP_RETRIES:  1x_auth_pae.c:2872 Max EAP identity request retries (3) exceeded for  client 00:21:6b:39:a1:ac
    *May 02 15:05:27.648: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872

    I have tried with WPA-PSK and tried the notebook to join it is joining but the Phone is not joiining getting the same error.
    connection failed.
    *May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:37:52.629: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:37:52.628: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:37:52.626: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:37:52.625: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:37:52.623: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:27:36.864: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:27:36.863: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:27:36.861: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:27:36.859: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:27:36.857: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:27:36.856: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:27:36.855: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:22:35.811: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:22:35.809: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:22:35.808: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:22:35.806: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:22:35.804: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:22:35.802: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:18:32.227: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
    *May 02 15:18:32.082: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2235 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:21:6b:39:a1:ac, SSID:voip,AP: c4:7d:4f:4b:a4:40.
    *May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:18:31.995: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:18:31.993: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:18:31.992: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:18:31.989: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:18:31.984: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:18:31.979: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:17:49.474: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:17:49.472: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:17:49.470: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:17:49.468: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:17:49.465: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:17:49.460: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:17:49.457: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:17:49.456: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:17:49.452: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:17:49.447: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:17:49.443: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:17:49.440: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:16:24.677: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 6(cisco_test) to 7(voip)
    *May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:14:20.572: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:14:20.571: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:14:20.569: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:14:20.568: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:14:20.567: %APF-3-SET_VAP_STATUS_FAILED: apf_api.c:15464 Could not Set the Status of Virtual Access point Entry.Encryption mode for static WEP does not match encryption mode for dynamic WEP on WLAN.Static WEP:1.Dynamic WEP:2. WLAN:'voip'
    *May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:14:20.566: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:14:20.564: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:14:20.562: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:14:20.560: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:08:45.139: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a6:d0
    *May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:08:45.137: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:a4:40
    *May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:08:45.135: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:4b:98:40
    *May 02 15:08:45.134: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:08:45.133: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f1:b0
    *May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:08:45.132: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:f0:d0
    *May 02 15:08:45.131: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:08:45.130: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP c4:7d:4f:46:e3:80
    *May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:08:45.129: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e9:90
    *May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:08:45.128: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e8:b0
    *May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:08:45.126: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e5:c0
    *May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:08:45.124: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:0d:e2:50
    *May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:08:45.122: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:70
    *May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:20904 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:08:45.120: %LWAPP-3-WLAN_ERR2: spam_lrad.c:21261 Unable to find WLAN 7 to be deleted; AP 00:3a:98:08:2f:60
    *May 02 15:08:43.623: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 4(CGC-7FL-WLAN) to 6(cisco_test)
    *May 02 15:07:35.339: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:541 Disconnecting mobile 00:21:6b:39:a1:ac due to switch of WLANs from 7(voip) to 4(CGC-7FL-WLAN)
    *May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'peap' to EAP profile for user 'test'. method already exist.
    *May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'tls' to EAP profile for user 'test'. method already exist.
    *May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'fast' to EAP profile for user 'test'. method already exist.
    *May 02 15:06:55.072: %AAA-3-EAPMETHOD_ADD_FAILED: localeap_db.c:2716 Unable to add method 'leap' to EAP profile for user 'test'. method already exist.
    *May 02 15:06:27.672: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872 Max EAP identity request retries (3) exceeded for client 00:21:6b:39:a1:ac
    *May 02 15:05:27.648: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2872

  • 1041N APs not joining 2100 WLC

    Hopefully this will be an easy solution for some of you.
    I have two LAP1041N APs I am trying to setup on a new 2100 WLC (7.0.116.0).  THe APs will blink green fast; then go to a green, red, blue cycle for a min or so; then back to blinking green fast.  Not sure what else to try here.
    Thanks for the help.

    Please use a L2/ L3 switch
    For a L2 swith the AP and WLC must be on the same VLAN iof the  L2 switch
    For AP:
    config t
    int gig 0/1
    swithport access native vlan 1( for ex)
    switchport mode access
    no shut
    For WLC :
    config t
    int gig 0/2
    switchport mode trunk
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 1
    no shut
    For L3 switch you can assign vlan interfaces :
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml#wlc
    Also here is the link to the discovery process:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml
    Thanks,
    Tuhin

  • Cisco 2702 not joining controller

    Controller code vs. 7.6.120.0
    From the controller:
    (Cisco Controller) >debug capwap packet enable
     Warning! Enabling this debug with large number of AP's connected, May flood console with message logs !!!.
     Are you sure you want to continue? (y/N)y
    (Cisco Controller) >*spamApTask3: Mar 05 13:38:13.317: <<<<  Start of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.317: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
    *spamApTask3: Mar 05 13:38:13.317:              HLEN 4,   Radio ID 0,    WBID 1
    *spamApTask3: Mar 05 13:38:13.317:              Msg Type   :   CAPWAP_DISCOVERY_REQUEST
    *spamApTask3: Mar 05 13:38:13.317:              Msg Length : 165
    *spamApTask3: Mar 05 13:38:13.317:              Msg SeqNum : 0
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.317:              Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
    *spamApTask3: Mar 05 13:38:13.317:              Vendor Identifier      : 0x00409600
    *spamApTask3: Mar 05 13:38:13.317:              WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
    *spamApTask3: Mar 05 13:38:13.317:              Maximum Radios Supported  : 0
    *spamApTask3: Mar 05 13:38:13.317:              Radios in Use             : 0
    *spamApTask3: Mar 05 13:38:13.317:              Encryption Capabilities   : 0x00 0x01
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
    *spamApTask3: Mar 05 13:38:13.317:              WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.317:              WTP Mac Type  : SPLIT_MAC
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *spamApTask3: Mar 05 13:38:13.317:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.317:
            IE            :   UNKNOWN IE 207
    *spamApTask3: Mar 05 13:38:13.317:      IE Length     :   4
    *spamApTask3: Mar 05 13:38:13.317:      Decode routine not available, Printing Hex Dump
    *spamApTask3: Mar 05 13:38:13.317: 00000000: 01 00 00 01                                       ....
    *spamApTask3: Mar 05 13:38:13.317:
    *spamApTask3: Mar 05 13:38:13.317:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
    *spamApTask3: Mar 05 13:38:13.317:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.317:
            IE            :   RAD_NAME_PAYLOAD
    *spamApTask3: Mar 05 13:38:13.317:      IE Length     :   16
    *spamApTask3: Mar 05 13:38:13.317:      Rad  Name     :
    *spamApTask3: Mar 05 13:38:13.317: AP1c6a.7aba.91ec
    *spamApTask3: Mar 05 13:38:13.317: <<<<  End of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
    *spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
    *spamApTask3: Mar 05 13:38:13.317: apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.317: apType = 41 apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
    *spamApTask3: Mar 05 13:38:13.317: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
    *spamApTask3: Mar 05 13:38:13.317: <<<<  Start of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
    *spamApTask3: Mar 05 13:38:13.318:              HLEN 4,   Radio ID 0,    WBID 1
    *spamApTask3: Mar 05 13:38:13.318:              Msg Type   :   CAPWAP_DISCOVERY_REQUEST
    *spamApTask3: Mar 05 13:38:13.318:              Msg Length : 165
    *spamApTask3: Mar 05 13:38:13.318:              Msg SeqNum : 0
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              Discovery Type : CAPWAP_DISCOVERY_TYPE_STATIC_CONFIG
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
    *spamApTask3: Mar 05 13:38:13.318:              Vendor Identifier      : 0x00409600
    *spamApTask3: Mar 05 13:38:13.318:              WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
    *spamApTask3: Mar 05 13:38:13.318:              Maximum Radios Supported  : 0
    *spamApTask3: Mar 05 13:38:13.318:              Radios in Use             : 0
    *spamApTask3: Mar 05 13:38:13.318:              Encryption Capabilities   : 0x00 0x01
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              WTP Mac Type  : SPLIT_MAC
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *spamApTask3: Mar 05 13:38:13.318:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.318:
            IE            :   UNKNOWN IE 207
    *spamApTask3: Mar 05 13:38:13.318:      IE Length     :   4
    *spamApTask3: Mar 05 13:38:13.318:      Decode routine not available, Printing Hex Dump
    *spamApTask3: Mar 05 13:38:13.318: 00000000: 01 00 00 01                                       ....
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
    *spamApTask3: Mar 05 13:38:13.318:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.318:
            IE            :   RAD_NAME_PAYLOAD
    *spamApTask3: Mar 05 13:38:13.318:      IE Length     :   16
    *spamApTask3: Mar 05 13:38:13.318:      Rad  Name     :
    *spamApTask3: Mar 05 13:38:13.318: AP1c6a.7aba.91ec
    *spamApTask3: Mar 05 13:38:13.318: <<<<  End of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
    *spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
    *spamApTask3: Mar 05 13:38:13.318: apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.318: apType = 41 apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
    *spamApTask3: Mar 05 13:38:13.318: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
    *spamApTask3: Mar 05 13:38:13.318: <<<<  Start of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.318: CAPWAP Control mesg Recd from 192.168.1.28, Port 43295
    *spamApTask3: Mar 05 13:38:13.318:              HLEN 4,   Radio ID 0,    WBID 1
    *spamApTask3: Mar 05 13:38:13.318:              Msg Type   :   CAPWAP_DISCOVERY_REQUEST
    *spamApTask3: Mar 05 13:38:13.318:              Msg Length : 165
    *spamApTask3: Mar 05 13:38:13.318:              Msg SeqNum : 0
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_DISCOVERY_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              Discovery Type : CAPWAP_DISCOVERY_TYPE_UNKNOWN
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_BOARD_DATA, Length 62
    *spamApTask3: Mar 05 13:38:13.318:              Vendor Identifier      : 0x00409600
    *spamApTask3: Mar 05 13:38:13.318:              WTP_SERIAL_NUMBER : AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_DESCRIPTOR, Length 40
    *spamApTask3: Mar 05 13:38:13.318:              Maximum Radios Supported  : 0
    *spamApTask3: Mar 05 13:38:13.318:              Radios in Use             : 0
    *spamApTask3: Mar 05 13:38:13.318:              Encryption Capabilities   : 0x00 0x01
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_FRAME_TUNNEL, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              WTP Frame Tunnel Mode : NATIVE_FRAME_TUNNEL_MODE
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_WTP_MAC_TYPE, Length 1
    *spamApTask3: Mar 05 13:38:13.318:              WTP Mac Type  : SPLIT_MAC
    *spamApTask3: Mar 05 13:38:13.318:
    *spamApTask3: Mar 05 13:38:13.318:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 10
    *spamApTask3: Mar 05 13:38:13.318:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.318:
            IE            :   UNKNOWN IE 207
    *spamApTask3: Mar 05 13:38:13.318:      IE Length     :   4
    *spamApTask3: Mar 05 13:38:13.319:      Decode routine not available, Printing Hex Dump
    *spamApTask3: Mar 05 13:38:13.319: 00000000: 01 00 00 01                                       ....
    *spamApTask3: Mar 05 13:38:13.319:
    *spamApTask3: Mar 05 13:38:13.319:       Type : CAPWAP_MSGELE_VENDOR_SPECIFIC_PAYLOAD, Length 22
    *spamApTask3: Mar 05 13:38:13.319:              Vendor Identifier  : 0x00409600
    *spamApTask3: Mar 05 13:38:13.319:
            IE            :   RAD_NAME_PAYLOAD
    *spamApTask3: Mar 05 13:38:13.319:      IE Length     :   16
    *spamApTask3: Mar 05 13:38:13.319:      Rad  Name     :
    *spamApTask3: Mar 05 13:38:13.319: AP1c6a.7aba.91ec
    *spamApTask3: Mar 05 13:38:13.319: <<<<  End of CAPWAP Packet  >>>>
    *spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Request from 192.168.1.28:43295
    *spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 5, joined Aps =0
    *spamApTask3: Mar 05 13:38:13.319: apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.319: apType = 41 apModel: AIR-CAP2702I-A-K9
    *spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28 port 43295
    *spamApTask3: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:e0 Discovery Response sent to 192.168.1.28:43295
    *spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Received LWAPP DISCOVERY REQUEST to 6c:fa:89:da:ff:00 on port '1'
    *spamApTask0: Mar 05 13:38:13.319: Start of Packet
    *spamApTask0: Mar 05 13:38:13.319: Ethernet Source MAC (LRAD):      1C:6A:7A:BA:91:ED
    *spamApTask0: Mar 05 13:38:13.319: Msg Type       :
    *spamApTask0: Mar 05 13:38:13.319:    DISCOVERY_REQUEST
    *spamApTask0: Mar 05 13:38:13.319: Msg Length     :   70
    *spamApTask0: Mar 05 13:38:13.319: Msg SeqNum     :   0
    *spamApTask0: Mar 05 13:38:13.319:
            IE            :   UNKNOWN IE 58
    *spamApTask0: Mar 05 13:38:13.319:      IE Length     :   1
    *spamApTask0: Mar 05 13:38:13.319:      Decode routine not available, Printing Hex Dump
    *spamApTask0: Mar 05 13:38:13.319: 00000000: 01                                                .
    *spamApTask0: Mar 05 13:38:13.319:
            IE            :   UNKNOWN IE 50
    *spamApTask0: Mar 05 13:38:13.319:      IE Length     :   46
    *spamApTask0: Mar 05 13:38:13.319:      Decode routine not available, Printing Hex Dump
    *spamApTask0: Mar 05 13:38:13.319: 00000000: 00 00 00 00 00 00 00 00  00 00 00 00 46 54 58 31  ............FTX1
    00000010: 38 33 30 53 34 50 39 00  00 00 00 00 00 00 00 00  830S4P9.........
    00000020: 00 00 00 00 01 01 00 0
    *spamApTask0: Mar 05 13:38:13.319:
            IE            :   RAD_PAYLOAD
    *spamApTask0: Mar 05 13:38:13.319:      IE Length     :   14
    *spamApTask0: Mar 05 13:38:13.319:              H/W  Version            :   1
    *spamApTask0: Mar 05 13:38:13.319:              H/W  Release            :   0
    *spamApTask0: Mar 05 13:38:13.319:              H/W  Maint              :   0
    *spamApTask0: Mar 05 13:38:13.319:              H/W  Build              :   0
    *spamApTask0: Mar 05 13:38:13.319:              S/W  Version            :   7
    *spamApTask0: Mar 05 13:38:13.319:              S/W  Release            :   6
    *spamApTask0: Mar 05 13:38:13.319:              S/W  Maint              :   100
    *spamApTask0: Mar 05 13:38:13.319:              S/W  Build              :   0
    *spamApTask0: Mar 05 13:38:13.319:              Boot Version            :   15
    *spamApTask0: Mar 05 13:38:13.319:              Boot Release            :   2
    *spamApTask0: Mar 05 13:38:13.319:              Boot Maint              :   4
    *spamApTask0: Mar 05 13:38:13.319:              Boot Build              :   5
    *spamApTask0: Mar 05 13:38:13.319:              numSlots       :   0
    *spamApTask0: Mar 05 13:38:13.319:              numFilledSlots :   0
    *spamApTask0: Mar 05 13:38:13.319: End of Packet
    *spamApTask0: Mar 05 13:38:13.319: 1c:6a:7a:ba:91:ec Discarding discovery request in LWAPP from AP supporting CAPWAP
    (Cisco Controller) >
    From the AP:
    *Mar  5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
    *Mar  5 19:48:43.007: LWAPP_CLIENT_EVENT: spamResolveStaticGateway  - gateway found
    *Mar  5 19:48:43.007: LWAPP_CLIENT_EVENT: spamSendDiscoveryRequest: sending discovery type 1 to 192.168.1.40
    *Mar  5 19:48:53.007: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Mar  5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
    *Mar  5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
    *Mar  5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
    *Mar  5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Mar  5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
    *Mar  5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
    *Mar  5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
    *Mar  5 19:51:52.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Mar  5 19:50:53.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
    *Mar  5 19:51:22.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
    *Mar  5 19:51:52.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.1:5246
    *Mar  5 19:51:52.999: %SYS-3-MGDTIMER: Uninitialized timer, timer stop, timer = 3AFD270. -Process= "CAPWAP CLIENT", ipl= 0, pid= 74
    -Traceback= 119AF80z 12A89C8z 12AA11Cz 16F512Cz 17645ECz 16FF088z 172810Cz 17299B4z 1720150z 1720228z 17204ECz 1717E50z 172F6A0z 173075Cz 1324C90z 1309B58z
    *Mar  5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  5 19:51:52.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  5 19:51:52.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
    *Mar  5 19:51:52.999: LWAPP_CLIENT_EVENT: parse_lwapp_config: hostname AP1c6a.7aba.91ec
    end
    *Mar  5 19:51:53.003: LWAPP_CLIENT_EVENT: lwapp_mesh_enable_dhcp - allow DHCP
    *Mar  5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: cdp run
    end
    *Mar  5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0
    cdp enable
    end
    *Mar  5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet0.1
    cdp enable
    end
    *Mar  5 19:51:53.003: LWAPP_CLIENT_EVENT: parse_lwapp_config: interface GigabitEthernet1
    cdp enable
    end
    *Mar  5 19:51:53.007: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  5 19:51:53.007: LWAPP_CLIENT_EVENT: parse_lwapp_config: line vty 0 15
     transport input all
    exit
    end

    "test mesh mode local" is not a supported command on the AP.  I tried to see if there was another syntax but couldn't find it.  
    AP1c6a.7aba.91ec#test mesh mode local
                           ^
    % Invalid input detected at '^' marker.
    AP1c6a.7aba.91ec#test ?
      GigabitEthernet   GigabitEthernet IEEE 802.3z
      Virtual-Template  Virtual Template interface
      aaa               AAA Authentication, Authorization and Accounting
      arp_retry         Test ARP Retry
      capwap            CAPWAP test commands
      cef               Cisco Express Forwarding test command
      cpuaccounting     CPU Accounting test commands
      cpurmi            CPU RMI test commands
      crypto            Test crypto functions
      dpaa              DPAA test commands
      dtls              DTLS test commands
      ecc               ECC test commands
      evtlog            Evtlog test commands
      ifs               IFS TEST code
      interfaces        Network interfaces
      iphc              IPHC testing
      opssl             OPSSL Test
      pb                Test parameter block file system
      persistent        Persistent commands
      process           Create/kill test processes
      rib               RIB function test
      rmi               RMI test commands
      rtcp              Test RTCP SSM
      save              save load monitor snapshot
      spanning-tree     Spanning Tree Subsystem
      ssm               SSM test commands
      tar               test tar file system
      topology          Routing Topology test command
      transport         TACTIC - transport test commands
    AP1c6a.7aba.91ec#test
    From the AP:
    AP1c6a.7aba.91ec#show version
    Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JB5, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Thu 01-May-14 22:18 by prod_rel_team
    ROM: Bootstrap program is C2700 boot loader
    BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
    AP1c6a.7aba.91ec uptime is 46 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP2702I-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
    Processor board ID FTX1830S4P9
    PowerPC CPU at 800MHz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.6.100.0
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 1C:6A:7A:BA:91:EC
    Part Number                          : 73-15824-03
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC182876JM
    Top Assembly Part Number             : 800-41174-01
    Top Assembly Serial Number           : FTX1830S4P9
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP2702I-A-K9
    Configuration register is 0xF
    AP1c6a.7aba.91ec#
    From the WLC:
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.6.130.0
    Bootloader Version............................... 1.0.20
    Field Recovery Image Version..................... 7.6.101.1
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... xxxxxxx_lab
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 192.168.1.40
    Last Reset....................................... Software reset
    System Up Time................................... 0 days 1 hrs 0 mins 6 secs
    System Timezone Location......................... (GMT -6:00) Central Time (US and Canada)
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    --More-- or (q)uit
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +36 C
    External Temperature............................. +41 C
    Fan Status....................................... 4700 rpm
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 1
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 6C:FA:89:DA:FF:00
    Maximum number of APs supported.................. 5
    (Cisco Controller) >

Maybe you are looking for

  • Windows 8.1 update continues updating 6 hour after

    This morning Windows ask me to reboot for install some updates, I say yes and now six hours after it continues updating at the same step 'installing update 6 of 12' I don't know what to do. Can I stop the updating process? I tried to switch off my co

  • BAPI to retrieve partial deliveries in purchase order item level

    We have implemented an invoice scanning solution for all our purchasing documents, we seem to have an issue picking up partial deliveries in our scanning interface, in the delivery schedule at item level, if the delivery is not complete, you will see

  • Shipping Point VS transportation planning point

    Hello Gurus, Could you please the answer the following questions? What is the different between shipping point and transportation planning point? Where is the transportation planning point assigned to? Why exactly we require the shipping documents in

  • How to find Maint. Release, Consolidated Update,Family Pack info?

    During Metalink patch download for E-business suite it asks below information 1) Maintenane Release 2) Consolidated Update (CU) 3) Family Pack How I can find these infos from current installation?

  • I want to integrate oracle with sap netweaver.

    Hello friends, I want to integrate sap netweaver with oracle backend system.I've Sneak Preview trail version.. how can i do that?? need steps..or screen shots..and also that can we display that pulled data in a graphical manner like bar chart or pie