Cisco connect software wants to match the admin password to cisco connect password?

As much as possible i want only one SSID for my router, so i dont want to have another SSID for guest. To protect my router
settings I need to have a different admin password from those of passphrase (i.e. wifi password).
Why is it that cisco connect software wants to match the admin password to cisco connect password?
The cisco connect password is the same as the passphrase. I think its unsafe to have similar passes for both admin password
and passphrase.
Is there any way that cisco connect software would work under different admin password & passphrase?

From what I can tell, the router is set up so that it broadcasts two seperate SSID's with two unique passwords. If you logon to the SSID-Guest network, you are not allowed any kind of Admin access to the router. If you attempt to use the Cisco Connect software, you'll eventually get an error saying that it could not find a network (unless there is an unconfigured router running factory defaults in range). I verified this using a Cisco Linksys E4200 and a few laptops.
So long as you utilize the guest network properly, you should be able to maintain security on your network and use Cisco Connect. Obviously this isn't ideal for most commercial use, but then again I don't know why you would want to use this software on that scale.
If you are trying to keep one SSID for the network, I think you're going to have to use the web based service and do a little manual configuration.
TLDR: Seta different password for the guest network and never give out the primary network password. Guests don't have admin access, even while using Cisco Connect so long as they are connected to the -Guest SSID.

Similar Messages

Remote Desktop - The Remote Desktop administrator software does not match the installed client software version.

Hi,
I just upgraded to Mavricks and get this when I try to launch Remote Desktop:
The Remote Desktop administrator software does not match the installed client software version.
I tried removing the application and reinstalling it to no avail. Any suggestions?
Thanks.
-David J. Eisen

Hi coold88!
I have an article for you that addresses your issue:
Remote Desktop 3: How to install Remote Desktop Administrator software after the client software has been updated
http://support.apple.com/kb/HT3596
You will want to make sure you have the latest version of the software as well:
About Apple Remote Desktop 3.7
http://support.apple.com/kb/HT5896
Thanks for using the Apple Support Communities. Have a good one!
-Braden

While editing a scanned pdf, Acrobat will not recognize the current font & change to very different font. How can I choose the font I want to match the current document?

While editing a scanned pdf, Acrobat will not recognize the current font & change to very different font. How can I choose the font I want to match the current document?

Thanks for answering. The version is XI.0.10. I just did the update yesterday hoping that I could now properly edit a scanned pdf document. Yes, it's happening on most all scanned documents. I followed your steps & found the list of fonts used in the document & then attempted to edit. The same occurs. When I type in a correction, I get an error alert... "the original font (in this case Fd 5805) is not available or can't be used in editing. Acrobat is using the font Minion Pro in its place."
When I select the text & right click as you suggested, my only choices are cut, copy, delete or select all, no "edit text".
I have no other options to choose another font. Thanks for any help you can direct my way.
Debbie
From: sukritd15 <[email protected]>
To: Deborah Karr <[email protected]>
Sent: Friday, February 13, 2015 5:35 AM
Subject: While editing a scanned pdf, Acrobat will not recognize the current font & change to very different font. How can I choose the font I want to match the current document?
While editing a scanned pdf, Acrobat will not recognize the current font & change to very different font. How can I choose the font I want to match the current document?
created by sukritd15 in Creating, Editing & Exporting PDFs - View the full discussionHi Deborah , I would like to know couple of things before I assist you further.1.Which version of Acrobat are you using ?2.Is it happening for all the scanned PDF' or any particular PDF? You can try these steps,Launch the scanned PDF >right click >Document Properties(from the drop down list) >Fonts(on the dialog box)>From here you will get the fonts used in that PDF . While editing the PDF ,select the text that are editing or typing in with the help of selection tool .After you select the text ,right click on the text and choose "edit text" from the drop down list .From there you will be able to choose the desired font . RegardsSukrit Dhingra If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7190881#7190881 and clicking ‘Correct’ below the answer Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7190881#7190881 To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following" Start a new discussion in Creating, Editing & Exporting PDFs by email or at Adobe Community For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

I want to upgrade the IOS of my Cisco 2821 from Version 12.4(11) to v 15.1 (XB), but I have CCME v 4.2 (0), is there any problem if I only upgrade the IOS and leave the CCME as it ?

I want to upgrade the IOS of my Cisco 2821 from Version 12.4(11) to v 15.1 (XB), but I have CCME v 4.2 (0), is there any problem if I only upgrade the IOS and leave the CCME as it ?
Thanks

CME is part of the IOS, so you can't upgrade the IOS seperately from CME.
That said, if this is a production environment you should proceed with caution and be prepared to roll back as you may find bugs, etc.
You should also look at release notes and make sure your phone firmware will still work or needs to be upgraded too.
Brandon

While updating the software from 6.1.3 to 6.1.4 on iPhone 5, the power failed. iTunes had just finished the backup and was beginning the software update. Now the phone screen says to connect to iTunes but the phone is not recognised when plugged in.

While updating the iPhone 5 software from 6.1.3 to 6.1.4, the power failed. iTunes had just finished the backup and was beginning the software update. Now the phone screen says to connect to iTunes but the phone is not recognised when plugged in. Using Windows 7 and phone not recognised by computer, let alone by iTunes.
Any suggestions? Happy to take it off to the the Apple genius people but would prefer to get it running myself.
Regards.

Try this
iOS: Device not recognized in iTunes for Windows

Configure the ADMIN and CLUSTER service connections to be SSL

Can you configure the ADMIN and CLUSTER service connections to be SSL
rather than tcp?
I was wondering about the present or future ability to secure other
connection services with SSL. Can you now or are there future plans
to configure the ADMIN and CLUSTER service connections to be SSL
rather than tcp? I suppose I should add the PORTMAPPER to that list.
My primary interest is for an SSLCLUSTER service in the case where
two brokers are connected over a non-trusted network. It may
not be too difficult to secure all the services the same way, but
perhaps that is on the TODO list.
A related question is if there are plans to add SSL with client
authentication as a stronger authentication mechanism than 'simple'
username and password. I believe you could get the username from
the client certificate's DN and continue to use the same LDAP user
repository for access control. I think this is similar to the way
that BEA's Weblogic server does it.
Finally should it be possible to deploy the HTTP tunnel servlet to
a webserver (such as iPlanet Web Server) configured to do SSL with
client authentication as a work-around to get stronger authentication
with the current release of the product? Or am I perhaps missing some
obvious and important detail? :) I guess I would like to know it's been
done already or is at least possible before I try and do it myself.

3 scenarios involving SSL are:
1: JMS client <------- SSL -------> iMQ broker
2: iMQ admin <------- SSL -------> iMQ broker
3: iMQ broker <------- SSL -------> iMQ broker (i.e clusters)
(1) is currently supported in iMQ 2.0
(2) and (3) is not supported in iMQ 2.0. No concrete plans yet to support
it in the near future but we'll definitely consider doing it if we
hear a lot of demand for it.
]A related question is if there are plans to add SSL with client
]authentication as a stronger authentication mechanism than 'simple'
]username and password. I believe you could get the username from
]the client certificate's DN and continue to use the same LDAP user
]repository for access control. I think this is similar to the way
]that BEA's Weblogic server does it.
This is on our todo list, but due to other more pressing issues we
have not been able to address it. We will continue to keep it
on our potential list of new features.
Sorry if I sound pretty wishy-washy in my responses above, but the fact
is that the things you mentioned above had to take a backseat
to other more critical features. That and the usual time/resource
constraints caused them not to be implemented.
]Finally should it be possible to deploy the HTTP tunnel servlet to
]a webserver (such as iPlanet Web Server) configured to do SSL with
]client authentication as a work-around to get stronger authentication
]with the current release of the product? Or am I perhaps missing some
]obvious and important detail? :) I guess I would like to know it's been
]done already or is at least possible before I try and do it myself.
Yes, this should be possible (although I don't believe we've tried it here).
The client authentication here is really only between the JMS client and the
web server (not between the tunnel servlet and the iMQ broker) and should
be similar in setup to any other java application talking to iPlanet Web
Server.

ITunes could not connect to this iPhone. The device is no longer connected

A few days ago, my iPad 3 A1430 screen turned black. Siri was still there but very slow to respond. The following day, the screen display returned (the usual green background colour but a much smaller display and not a single icon present). Siri was back up to speed, could play music, display info but could not respond to calendar enquiries etc. The iPad would switch off but not reboot. I let the battery level drop to zero then re-charged: iPad now working again.
Wanting to back-up my iPad, I ran iTunes version 12.1.0.50 on iMac (Yosemite 10.10.2). I have PCemulator installed and when the iPad connection was made, I received the usual screen prompt for which to connect to Mac or PC. (The problem starts here: - the prompt was flashing on/off). I selected Mac & received the message “iTunes could not connect to this iPhone. The device is no longer connected”.
Rebooted PC and iPad, connecting iPad offers no device prompt, only the same error message.
Successfully backed up iPhone 6 using iTunes.
Upgraded iPad software to IOS 8.2 and connected again. No effect, same error message.
Looked at various Apple posts but couldn’t find a solution. After several iMac & iPad reboots, eventually managed to back-up my iPad and in the process lost all my iPad music built up over the years on my old PC. Managed to recover these music files from my old PC and load them onto iTunes on my iMac. Tried to sync my iPad but back to error message “iTunes could not connect to this iPhone. The device is no longer connected”.
Any solution?

I have the same problem. In fact when I plug in my iPad 2 updated to ios 7.0.4 I get that same message and it crashes my entire system - forcing me to reboot.

HT201328 I received a message that my iphone 4S was unlocked and that I should connect to iTunes to complete the process. When I connect to itunes I do not get the message "Congratulations you iphone has been unlocked". I have the latest itunes. Welcome h

I received a message that my iphone 4S was unlocked and that I should connect to iTunes to complete the process. When I connect to itunes I do not get the message "Congratulations you iphone has been unlocked". I have the latest itunes. Welcome help.
ihabf
[email protected]

See Here
https://discussions.apple.com/message/15290457#15290457
From the More Like This on the right...

Ay suggestions to connect my iPhone 5 to the Internet, it will only connect when sat next to the rooter, I have reset signals on both ?

Ay suggestions to connect my iPhone 5 to the Internet, it will only connect when sat next to the rooter, I have reset signals on both ?

What version of iOS?
Is the router running the latest version of available firmware?
Are any other devices having issues connecting to the router?
Does the iPhone have the same issue with other Wi-Fi hot spots?

Can Cisco IME software run on desktop without admin privileges?

I do workstation support and our network administrators do not have admin on their Windows 7 workstations, is there a way to install the CISC IPS Manager Express and have it run without needing admin permissions on the desktop? I thought I had it working (with shims and Microsoft Application Compatibility Toolkit) then it said it needed the admin permissions for making the SQL connection.
Please let mw know why this application requires admin and if there is a work around.
Thank you!
Fred

I'm afraid I have no personal experience with what you're attempting to do...
All I can remember is that Full Admin rights were supposed to be granted to the user account during the entire installation of Palm Desktop, and a successful HotSync performed. Whether the check-out routine is doing this is beyond me.
Once the above is complete, the rights can be revoked back to "User".
You might want to search over at Brighthand.com for some information on this subject.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

I want to change the admin passwork for my Mac G4.

The "help" content says to insert the install disc and click"install". I just read a post where the guy lost all of his files. When I put in my install disc and click on "install" it asks for the password...
can some help me? Thanks, Collette

When you boot from the CD go up to the installer menu and click reset password
Go to this link and scroll down to:
Resetting the original administrator account password
http://docs.info.apple.com/article.html?artnum=106156

I have an ATV 1 which is connected to my Bose Lifestyle System. I just expanded the system and connected a second AMP for the expansion. Can I connect the ATV 1 to the aux jacks (RCA Cables) of the expansion amp? Thanks

I have an ATV 1 which is connected to my Bose Lifestyle System. I just expanded the system outdoors using a second Bose System Amp. Does anyone know if I'm able to connect my ATV 1 to the Bose expansion module in addition to keeping it connected to my main Lifestyle System using RCA cables? The new amp has RCA input jacks for auxiliary inputs. Thank you.

hello, normally such issues are caused by a firewall/security software which doesn't recognize & therefore blocks new firefox versions. please remove all program rules for firefox from your firewall and let it detect the new version of the browser again.
[[Fix problems connecting to websites after updating Firefox]]

I want to access the database with user name and password without con. info/udl

hi to all,
im doing project related with database... normally i'll connect ***.udl file to open database.vi.
now what is my question is I want to open the database with the user name with password.... y i need this because once i run the program the program should ask username and password to open database for write/read operation. if its wrong user name and password means program should be denied...
can any tell how to access the database toolkit with the username with password....
im using labview 7.0...
i think my question is clear....waiting for reply thank you in advance...
pls see this attachment.....
Regards,
N. Srinivasan
Attachments:
access.vi ‏37 KB

i have already read that link in the discussion forum...but im still have some confussion in... i attached file is so like to give user name and password..?
and one more things can tell wat to do in ODBC and MDB and in UDL for password lock.. each time i run the promgram it should ask password to acces the database..
thank you a lot for your reply..
it will be more more useful if u clear my doubts clearly....
Regards,
N. Srinivasan
Attachments:
user=pass.PNG ‏35 KB

I have an IPA2 wifi 3g working fine with wifi up for 3 monthes then from two weeks it get connection but after 1 minutes stop to serf/download with signal and connection always present. With the same router are still connected others 3 pc working!

I all,
the scenario is the following:
WIFI connection with TISCALI operator. Encryption made by WPA2 EAS with router SITECOM or tested also with another router DIGICOM with WPA TPK.
From December up to end of March the IPAD2 working perfectly serfing and downloading.
By two weeks it has a very strange behavour without have changed any configuration on IPAD or network:
with WIFI turned on it discover about 4 different ntw among them the mine, I successfully authenticate with psw the my ntw,
the IPAD2 start to run with Safari without problems, but after about 1 minutes, it stop to serf or download and answer that the Server cannot be reached or the page cannot be open, at the same time the signal is present on the icon of WIFI and it is strong.
This problem is systematic: If I dissasociate the ntw and then authenticate again I start to serf again for 1 minutes (more or less) and then it stops again, this occurs every time I authenticate the ntw after a disassociation.
I made some test changing the encryption from WPA2, WPA and also without encryption but the result was always the same, after about one minute the server seems to be for the IPAD2 no more reachable while the others PC and netbook connected to the same router continue to serf/download without problems!
I also tried to change the router with a DIGCOM that I did not use generally, but the behavour is always the same.
Since the IOS was the 4.3 revisin, I made the upgrade by means Itunes to IOS 5.1 succesfully installed.
But unfortunatelly all test repeted have had the same negative result with the same behavour!
Yesterday I tried to do the complete restore of the System but the tests had the same rsult.
I really don't know how to proceed, the problem started suddenly without any action from my side....is there someone that can help me?
Thanks Massimo

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
 Cheers, Tom

HT4798 Help - I bought a nearly new iMac but I don't know the admin password, is there a default? Trying to install software and it needs the admin password.

I have wanted to move to a Mac for some time now as I am a keen photographer, I bought a very nice Imac 21.5 May 2011 model OS Lion and it is wonderful.
Just tried to put my Adobe Photoshop software on and it asks to log in to Admin and asks for the password, I have tried the 'link to your Apple ID' but it doesn't seem to want to work.
Any help out there?
Barry

Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
     When the menubar appears select Terminal from the Utilities menu.
     Enter resetpassword at the prompt and press RETURN. Follow
     instructions in the dialog window that will appear.
     Or see Reset a Mac OS X 10.7 Lion Password and
     OS X Lion- Apple ID can be used to reset your user account password.

Cisco connect software wants to match the admin password to cisco connect password?

Similar Messages

Maybe you are looking for