Cisco PI configuration template output redirection

hi all,
I need to configure a configuration template to find the output of "show cdp neighbor" using Cisco PI and redirect the output to another server like ftp or tftp.
please advise

Hi Mohamed,
Go to Design > Feature Design >CLI template > System CLI template >> select any template and click on "Save as new Template"
that new template will be under Design > Feature Design > My template > EDIT it and add the command that you want to use " show cdp neighbour".
Then DEPLOY it against the devices that you want to deploy.
You can export the output , print it , however you will not be redirect the output directly to ftp or tftp server
Thanks-
Afroz
****Ratings Encourages Contributors ****

Similar Messages

Cisco MX200 - Cisco TMS Configuration Template

Good Afternoon all,
I have a MX200 to configure and trial along with an EX60.
We use MXP75,95's and E20's currently, which have Configuration Templates with various settings in.
I have uploaded the XML file to the system, under Systems -> Provisioning and it is detected with the hardware and software versions.
When I go under Systems -> Configuration Templates -> I cannot select the MX300 or EX60.
I am wondering how to configure these new devices for use?
Regards,
Matt

no, there is not a single template you can use at that level to configure both the WLAN and the User Idle timer.
One is a WLAN setting, the other is a Controller General Setting.
Now that being said, you could use a CLI template to push both changes, so long as you remember to disable and then reenable the WLAN before/after the Session timeout commands.
HTH,
Steve

WLAN Configuration Template of Cisco Prime 2.1

Hi ,
We have added WLC 5508 in cisco prime 2.1.0.87 wherin if we try to configure WLC Configuration template then its not reflecting existing WLAN as we need to do changes in existing WLAN with configuration template. Same way we are unable to find all listed MAC-Filter list in WLAN Confiuration template to execute the template .
Can Any one help me on the same?
Thanks in advance.

Services running fine..
check it with other Browser , Supported browser are below::
–   Google Chrome 31 or later.
–   Microsoft Internet Explorer 8.0 or 9.0 with Google Chrome Frame plugin (users logging in to the simplified Lobby Ambassador interface do not need the plugin).
–   Mozilla Firefox ESR 24.
–   Mozilla Firefox 24, 25 or 26.
If above does not help , reboot the server once and check the issue again.
Thanks-
Afroz
***Ratings Encourages Contributors ****

PLD Document Configuration Template

Hi All,
Can anyone please let me share any of the PLD Document Configuration Templates. This is for requirement documentation. Based on this we would like to design the SBO outputs for all the marketing and other documents. Any help would be of great value.
Thanks & Regards
Shiva

Documentation can found in this link:
https://websmp206.sap-ag.de/smb/sbocustomer

Prime InfraStructure 2.2 Configuration Template error

Hi All,
I'm facing Configuration template error . I can add the CLI template then after i press on Deploy i get error message and this is happening with all the CLI templates . ( also Attached the error )
The error message : "
Template Deployment- Prepare and schedule : HA With Virtual IP
There was an error while parsing and rendering the content. (updateLeftTreeOnce is not defined )
The HA With Virtual IP Template Body as below :
logging 10.30.2.252
ip access-list standard VTY_ACCESS
no deny any log
permit 10.30.2.252
deny any log

We are facing the exact same issue. Here are the version :
Cisco Prime Infrastructure
Version : 2.2.0
Build : 2.2.0.0.158
We tried restarting the NCS services, but it doesn't help. We have the issue on differents PC and browsers. Users told me they got the issue before but it disappeared by itself. We will open a case about it.

Issues with using the output redirection character with newer NXOS versions?

Has anyone seen any issues with using the output redirection character with newer NXOS versions?
Am receiving "Error 0x40870004 while copying."
Simply copying a file from bootflash to tftp is ok.
This occurs for both 3CDaemon and Tftpd32 softwares.
Have tried it on multiple switches - same issue.
Any known bugs?
thanks!
The following is an example of bad (NXOS4.1.1b) and good (SANOS3.2.1a)
MDS2# sho ver | inc system
system:    version 4.1(1b)
system image file is:    bootflash:///m9200-s2ek9-mz.4.1.1b.bin
system compile time:     10/7/2008 13:00:00 [10/11/2008 09:52:55]
MDS2# sh int br > tftp://10.73.54.194
Trying to connect to tftp server......
Connection to server Established. Copying Started.....
TFTP put operation failed:Access violation
Error 0x40870004 while copying tftp://10.73.54.194/
MDS2# copy bootflash:cpu_logfile tftp://10.73.54.194
Trying to connect to tftp server......
Connection to server Established. Copying Started.....
|
TFTP put operation was successful
MDS2#
ck-ci9216-001# sho ver | inc system
system:    version 3.2(1a)
system image file is:    bootflash:/m9200-ek9-mz.3.2.1a.bin
system compile time:     9/25/2007 18:00:00 [10/06/2007 06:46:51]
ck-ci9216-001# sh int br > tftp://10.73.54.194
Trying to connect to tftp server......
|
TFTP put operation was successful

Please check with new version of TFTPD 32 server. The error may be due to older version of TFPT server, the new version available solved this error. Files are getting uploaded with no issues.
1. Download tftpd32b.zip from:
http://tftpd32.jounin.net/tftpd32_download.html
2. Copy the tftpd32b.zip file into an empty directory and extract it.
3. Copy the file you want to transver into the directory containing tftpd32.exe.
4. Run tftpd32.exe from that directory. The "Base Directory" field should show the path to the directory containing the file you want to transfer.
At this point, the tftpserver is ready to begin serving files. As devices request files, the main tftpd32 window will log the requests.
Best Regards...

Configuration Template Builder WL8.1 does not work

Hello,
     After spending nearly 2 days now trying to get a Configuration Template
built, I've concluded this simply does not work. Has anyone used the
Config Template builder to package a semi-complex application on top of WLI?
     I'm trying to have 2 of my applications, the JMS and JDBC resources,
and a WLI event generator packaged up for easy deployment to someone
else's server configuration. The problem with this is that there are
required resources for WLI, namely a database. The Pointbase database
included for WLI does not get included in the template automatically.
There are also some flat-out bugs:
If you choose to include a resource adapter "application", such as
jms-xa-adp.rar, the template builder does not bundle this in the
template and deploy it correctly. The template builder restricts you to
putting applications in the relative path starting at ./
For jms-xa-adp.rar, its original location is in $WL_HOME/server/lib, and
the template builder defaults to put it in ./lib of your template.
However, when you create a domain with the template, jms-xa-adp.rar does
not get placed in your ./lib directory. This causes you to then go and
manually edit your config.xml to point back at $WL_HOME/server/lib or to
manually copy jms-xa-adp.rar into your ./lib directory (which the
template mechanism should do for you).
Relative paths in the config.xml file require you to execute the config
builder from the directory of the domain you are making a template for.
The template builder should instead be smart enough to realize that
relative paths in the config.xml file are relative to the directory that
the config.xml is in, not the one you are running the template builder
from. You'll get an error when trying to create the template cause it
won't find the resources if you're not in that directory.
If anyone has successfully used this to package a WLI application in a
template, please share your experiences and how to do so. In the
meantime, I'm claiming there is no way to nicely package up a server
configuration for a WLI app in Weblogic, and this is a big shortcoming.
Weblogic needs a simple transferrable way of creating server
configurations (it tries to do this with the template, but that is
failing). With JBoss, for example, you simply copy your server directory
into another installation. This doesn't work with Weblogic unfortunately
because it puts hard-coded paths in the config.xml file.
Thanks

Russ,
     Thank you for the detailed responses. The only one I'm currently
struggling with still is the #5, with the scripts between the two. One
of the major benefits of using a J2EE App Server is supposed to be the
portability between servers. I find it disconcerting that BEA Weblogic
restricts me to the platform I created the domain on by creating
platform-specific startup/shutdown scripts for only the platform created
on. It's understandable that a script converter would be difficult, but
at least both the .sh/.cmd files should be created from the first time
you make a domain. If the user only wants one or the other, they can
delete the appropriate one. It's also understandable that the
users/deployers shouldn't have to manually convert a startup/shutdown
script to take the domain to a different box.
     JBoss clearly has BEA beat on ease of deployment here. Their model is
the concept I'm thinking of: you have some generic startup/shutdown
scripts that can load a platform-independent server configuration. You
truly can copy directories as-is between JBoss installations.
     I was hoping to package up a server domain for use on any of the
supported platforms, but since I don't have the time to manually convert
the startup/shutdown scripts, I'm going to have to tell people it's only
for Solaris now.
     Hopefully BEA can fix this in a future SP. There's no need for this
platform-dependency. Also, if the Windows version can generate both
scripts at creation time, then the Solaris should be able to do this as
well (or at least give you the option).
Thanks again for the replies
russ wrote:
Hi Steven,
I have several comments and questions about your last two posts. I will try to
address them in order.
1) "The Pointbase database included for WLI does not get included in the template
automatically."
     By default the template builder only includes the *.cmd and *.sh files in the
template from your domain directory. If you begin building with an existing
domain template all files that were in the template will get included. This was
done because there is no way for the builder to automatically determine all the
files that are required by your template/domain and we steered away from recursively
including all files from the directory so that unused files were not needlessly
included. We can extrapolate some files based on the application paths in the
config.xml, but the rest is left up to the template builder to be aware of what
is needed for their domain to run. So, if you need the Pointbase *.dbn and *.wal
files included in your template just select these files on the ?Add Files? panel
of the template builder and add them to the ?Domain Directory?.
2) ?If you choose to include a resource adapter "application", such as jms-xa-adp.rar,
the template builder does not bundle this in the template and deploy it correctly.?
     The template builder considers application files to be in two categories: Imported
or Internal. When you are at the ?Add Applications? panel of the builder you
will see a checklist of all the applications that are in the domain you selected.
On the right hand side there are two text fields. The top one displays the application
path as it is currently set in the config.xml of that domain. The bottom field
will be different depending on what category the application falls into. As you
click on each application in the list, you may notice that the bottom field may
change from an editable field titled ?Imported Application Path? to a non-editable
field titled ?Internal Application Path?. The difference between the two categories
is that an ?Imported? application?s files will be included in the template jar.
An ?Internal? application?s files will not be included in the template jar because
they are considered internal to the weblogic installation. The jms-xa-adp.rar
should fall into the internal category and should not get included in your template.
     From what you are describing it sounds like the builder attempted to import that
application when it should not have. In an attempt to recreate the problem you
are seeing I deployed that Connector Module through the WLS console and ended
up with an application path of ?C:\bea\weblogic81\server\lib? where ?C:\bea\weblogic81?
is my WL_HOME (a.k.a. USER_INSTALL_DIR). If I then attempt to build a template
from this domain, the builder recognizes this as an internal path and does not
include it inside my template. If the current application path you had looks
different from the one above, that may explain why the builder was attempting
to import it. What was the value of the ?Current Application Path? for that application
deployment?
3) ?Relative paths in the config.xml file require you to execute the config builder
from the directory of the domain you are making a template for.?
     The builder is ?smart? enough to determine relative paths. You should not have
to invoke it from the domain directory you are working with. There is a known
bug in the WebLogic Platform 8.1.1.0 release of the template builder that will
cause it to not find files with relative paths in your domain directory if the
application path in the config.xml is just a ?.?. If this is the case, you should
see a FileNotFoundException when you attempt to create the template. This will
be fixed in SP2 and you can work around this problem by changing those paths to
?./? instead. If this was not the case, what was the path the wizard choked
on?
4) ?Looking through the config file, it seems that it's all of the WLI components
that have absolute paths in the config file. In addition, BEA_WLS_DBMS_ADK has
an absolute path, not sure if that is WLI or WLS. ?
     BEA_WLS_DBMS_ADK is an integration application. If you created the original
domain using the configuration wizard most of the applications in an integration
enabled domain will reference paths inside of you installation directory or ?internal?
paths. For instance, I used the wizard to create a ?Basic WebLogic Integration
Domain?. The path for that application in this domain is: ?C:\bea\weblogic81/integration/adapters/dbms/lib/BEA_WLS_DBMS_ADK.ear?
where ?C:\bea\weblogic81? is my WL_HOME or USER_INSTALL_DIR. When I load this
domain into the builder it shows this application as ?internal? and the ?Internal
Application Path? is "$USER_INSTALL_DIR$/integration/adapters/dbms/lib/BEA_WLS_DBMS_ADK.ear".
This will be set as the path value of this application in the config.xml that
will be included in the template you build. When you later use the Configuration
Wizard on this template it will substitute the $USER_INSTALL_DIR$ to the value
of the installation directory of the machine you are creating it on.
     If you were to Change these to relative paths, as Mark previously suggested,
it will only work if you copy the domain directory to the same location relative
to your installation directory on the target machine. Also, if you copy the domain
in this manner you will more than likely run into problems with your start/stop
scripts and be forced to hand modify all the paths contained within. The configuration
wizard tries to alleviate these problems and make the configuration entirely portable.
This gives the user who creates the domain from your template the ability to
put it anywhere they want regardless of the paths in the config.xml.
5) ?However, there is another major problem with the Template Builder: it only
includes the startup/shutdown script for the platform you create the template
on. ???I built the template on Solaris with the UNIX scripts. However, I tried
to create a new config on Windows with this template, and the scripts were not
converted to .bat files!?
     As I stated previously, the builder will only include *.cmd and *.sh scripts
into your template by default. If you created the domain on a unix platform using
the configuration wizard it will not extract the *.cmd files since these aren?t
considered to be useful on unix. If you were then to attempt building a template
from this domain and take it onto a windows platform, it will obviously be missing
any windows scripts. Conversely, the wizard will extract *.sh scripts on windows
because they can still be useful if a user has an MKS or Cygwin type environment
installed. The config wizard and template builder do not have the ability to convert
scripts. The builder will only include existing scripts that are in your domain
directory and automatically determine any necessary string substitutions that
will be needed. Please note that since WebLogic is only supported on the NT/2K/XP
versions of windows you will find that the wizards use ?.cmd? files and not ?.bat?
files since these are more commonly associated with Win 95/98/ME.
     I will be happy to answer any more questions you may have and would also like
to take a look at your domain configuration to try and get a better understanding
of the problems you are encountering.
thanx,
russ

How to configure Email output in SD

Dear friends Pls sent me details of how to configure email output in SD module.
<REMOVED>
Thanks & Regards,
<REMOVED>

Hi
Idoc Def :Standard SAP format for electronic data interchange between systems (Intermediate Document). Different message types (such as delivery confirmations or purchase orders) normally represent different specific formats, the IDoc types. However, multiple message types with related content can be assigned to one IDoc type: For example, the IDoc type ORDERS01 transfers the "logical" message types ORDERS (purchase order) and ORDRSP (order confirmation).
Idocs are of two types basic type and the extension type .we need to configure the system settings for this process .
IDOC (Intermediate Document) - A data holder.
IDOC is divided in to three parts.
Control Record
Data Record
Status Record
Control record (Table: EDIDC):
- Every IDOC has only one Control Record
- Each Control Record contains header information like:
o IDOC Number
o Direction of IDOC: Inbound or Outbound
o Date and Time of creation of IDOC
o Date and time when the IDOC was last modified.
o Message Type of IDOC
o IDOC type and extension of IDOC
o Sender and Receiver Partner
Data record (Table: EDID4):
- Data Record contains Data to be processed.
- Every IDOC has one data record with multiple segments in hierarchy.
- Segments and Hierarchy of Segments are defined by IDOC Type and Extension.
- IDOC created has to strictly follow the hierarchy; else IDOC fails with Syntax error.
- Segments which are repetitive have qualifiers attached to it
Status record (Table: EDIDS):
- Status Record describes the status of IDOC.
- Each IDOC contains one status Record with multiple status information.
- Status at each level is appended to IDOC. E.g. When IDOC is created in SAP, Status is This IDoc has been generated through a test transaction, When the IDOC is added to system it is IDOC added, IDOC ready to be transferred to Application
- Status should always be read bottom-up. Status at the top is the latest status.
- Some Example of Status Records:
o Inbound:
§ 53 - IDOC successfully posted
§ 51 IDOC Failed
§ 64 - IDOC ready to be transferred to Application
o
Outbound:
§ 30 IDOC ready for Dispatch
§ 03 IDOC passed to port OK
§ 12 IDOC Dispatched
§ 16 Functional Acknowledgement Positive
§ 17 functional Acknowledgement Negative
IDoc Type: Defines the segments and hierarchy of segments
o Transaction Code:
§ WE30 To create, change or display the IDOC type and the extension.
§ WE31 To create the Segment
- IDOC type defines the segments to be used in the IDOC.
- It also defines the hierarchy and syntax of the segments.
- IDOC extension is nothing but to add segments to standard IDOC types.
- Transaction WE31 allows you to create segments.
- Program RSEIDOC3 documents the use of each IDOC type.
Segments:
Attributes of a Segment:
- Mandatory Segment: If checked, this segment should always exist in the IDOC.
- Minimum Number:
- Maximum Number: Maximum number of times this segment can be repeated in IDOC. -
Parent Segment: Parent of this segment
- Hierarchy level: Level of hierarchy.
Segment Definition (WE31):
Messsage Type: Defines the type of data in the IDOC
o Transaction Code:
§ WE81 To create, change or display the Message type and the extension.
§ WE82 Using this transaction you can link Message Type, IDOC Type, IDOC Extension and version.
- Message type identifies the type of data IDOC holds. E.g. Orders (ORDERS), Delivery (DESADV), Invoice (INVOICE). It also defines what needs to be done with the data in the IDOC, in case of Inbound IDOC, and which data to be extracted in case of Outbound IDOC.
- Message Type is linked to a process code, which in turn is linked to a Function Module. This function module extracts from or posts data to SAP depending on direction of IDOC.
- Relation between Message Type, IDOC type and IDOC extension needs to define. Without this relation Message type or IDOC type cannot be used.
Message Type Create, Change or Display (WE81):
Setup link between Message Type, IDOC Type, IDOC Extension and Version (WE82)
Process Code: Function Module is linked to a process code. This function module in executed for inbound or outbound IDOC.
o Transaction Codes:
§ WE41 Outbound Process Code
§ WE42 Inbound Process Code
- Process codes are linked to a Function Module.
- Relationship is Message Type is linked to a Process Code which is linked to a Function Module.
- In case if you are using a stand alone code to trigger an IDOC, you need not define a process code.
RFC Destination: System definition of destination.
o Transaction Code: SM59
- RFC destination identifies the destination of IDOC.
- In case of ALE:
o In ALE the communication mode is IDOC to IDOC, hence the type used is R/3 Connections.
o It is the destination SAP system which will receive the IDOC.
o In RFC destination you define the destination SAP system details like System, Login and Password.
Go thr below links:
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEIO/BCMIDALEIO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCMIDALEPRO/BCMIDALEPRO.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/CABFAALEQS/CABFAALEQS.pdf
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/BCSRVEDISC/CAEDISCAP_STC.pdf
Sail

Copy AP Configuration Templates-WCS 7.0.172.0

I am wondering if anyone has seen a way to copy an AP configuration template. We have several distribution centers and the templates are essentially identical other than the Template name and the AP Group VLAN (different for each DC). We set up a new template for each new DC. Being able to copy a template, rename it and change the Group VLAN setting would save a lot of time.

I haven't been able to make it work like it was in prior versions. I have found you can initiate the session from monitor-->access points--->ap name and selecting the radio type. 802.11b/g/n, or 802.11a/n. The icon is under cleanair management operation.

Can't save Cisco ASA configuration in GNS3 via write memory command

Hi all,
I’m having a problem to save Cisco ASA configuration in GNS3 via write memory command.
   ciscoasa(config)# wr mem
   Building configuration…
   Cryptochecksum: c066a7ab b5b9071e bb5ee1f6 2d93be53
   %Error copying system:/running-config (Not enough space on device)
   Error executing command
   [FAILED]
   ciscoasa(config)#
Here are the details of the lab setup.
PC DETAILS:
   Windows 7 Enterprise SP1 64bit
   GNS3 v0.8.6 all-in-one (installer for 32-bit and 64-bit which includes Dynamips, Qemu/Pemu, Putty, VPCS, WinPCAP and Wireshark)
ASA DETAILS:
   13,279,888 asa802-k8.bin.unpacked.initrd
   1,095,856 asa802-k8.bin.unpacked.vmlinuz
Please advise. Thanks in advance.
http://firewallengineer.wordpress.com/2014/02/19/problem-cisco-asa-in-gns3-error-copying-systemrunning-config-not-enough-space-on-device/

instead of this:
To create a flash file
cd "C:\Program Files\GNS3\qemu-2.1.0"
qemu-img.exe create c:\FLASH 256M
try this:
To create a flash file
cd "C:\Program Files\GNS3\qemu-2.1.0"
qemu-img.exe create c:\User\usuario\GNS3\FLASH 256M
Let me know if is helpfull.

App-V: A Configuration Template for Deploying to Stateless RDS Clients on Citrix Published Desktops with Citrix UPM for Profile Management

Please Vote if you find this to be helpful!
App-V: A Configuration Template for Deploying to Stateless RDS Clients on Citrix Published Desktops with Citrix UPM for Profile Management
Just posted this to the wiki:
http://social.technet.microsoft.com/wiki/contents/articles/25318.app-v-a-configuration-template-for-deploying-to-stateless-rds-clients-on-citrix-published-desktops-with-citrix-upm-for-profile-management.aspx

I would not recommend this and keep the package cache and the client on the same non-persistent drive and enable the Shared Content Store. If you separate the cache and the App-V client they could get out of sync and strange behaviour can occur.
You can use a temporary local profile with Citrix UPM or UE-V and specify what to roam/save.
You can use the Shared Content Store so packages will stream over the network. When the user logs on there is a publishing phase where shortcuts etc are created for the user, this will take some time.
Are you using the App-V full infrastructure?
Are you using a boot disk, partition or PXE in combination with PVS?

Java input xml data and xsl template -output file excel

i need help or same special link on web.
i must develop code or use a special tool that make this.
INPUT:
xml that contain real data
xsl that explain a report template
OUTPUT:
file excel that show the template xsl with xml data source
thank for help me.

Hi,
Please refer to "Oracle XML Publisher User's Guide".
Applications Releases 11i and 12
http://www.oracle.com/technetwork/indexes/documentation/index.html
This is also explained in the document attached in (Publishing Concurrent Requests with XML Publisher [ID 295409.1]).
Thanks,
Hussein

Cisco dynamic configuration tool

Currently cisco dynamic configuration tool is not working. What can I do?

Richard,
The power supplies in the 6120 / 6140s are auto sensing for 120-240 VAC. Please see Table 9 in the Nexus 5000 document for all supported cables:
http://www.cisco.com/en/US/prod/collateral/switches/ps9441/ps9670/data_sheet_c78-461802.html
Thank you,
Matthew

Error in configuring the output type

Hi,
In sap script the requirement was to give option to select user whether they need to save the form in pdf or print/preview.
For this I have given a pop-up using popup_to_confirm before the OPEN_FORM function module in the driver program. and
depending on the option populate the OPTIONS parameter in the OPEN_FORM function module.
Now when I configuring the output type by going to the order screen and try to save it, the configuration is not saved and a update termination occurs due to the screen called in the popup_to_confirm function module.
How to avoid this problem?
Regards,
Tan

Hi Sucharita,
Steps to Maintain an output device in your user master record
1. From the menu,choose System --> User profiles --> Own Data
2. Select Default Tab of user profile and enter the output device in 'output device' field .
This should solve your problem.

Cisco Aironet Configuration Manual

I am new to Cisco Wireless Configuration. Anyone know please is there any website I can surf for Cisco Wireless Configuration Manual. Thanks to anyone who drops me a response.

Try this:
http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo_350/350cards/windows/legacy/scg/
Shawn

Cisco PI configuration template output redirection

Similar Messages

Maybe you are looking for