Cisco Router 2901,voice bundle 4FXO

Need Cisco Part no. for Cisco Router 2901,voice bundle 4FXO
email me [email protected]

Flavio,
It looks like you are missing the "ccm-manager mgcp" command in the global configuration mode.
To enable the gateway to communicate with Cisco CallManager through the Media Gateway Control Protocol (MGCP) and to supply redundant control agent services, use the ccm-manager mgcp command in global configuration mode.
http://www.cisco.com/en/US/docs/ios/12_3t/voice/command/reference/vrht_c4_ps5207_TSD_Products_Command_Reference_Chapter.html#wp1072910
Do a mgcp / no mgcp once its added. Make sure that the domain name on cucm is the same as it appears in the 'show ccm-manager' output on the gateway. If the issue persists, please post show tech as requested earlier.
HTH
Manish

Similar Messages

Configure cisco router 2901 as pppoe modem

hi, i used web based interface to configure ppoe on the router 2901, but it does not seems to be enabled.
i want to use this router to connect to my ISP and dial automatically like the normal dlink and other routers do.
i want to share the internet to clients connected through switch.

conf t
interface dialer 1
ip address negotiated
encapsulation ppp
ppp authentication pap callin
ppp pap sent-username ISPUsername password ISPPassword
ppp ipcp route default
dialer pool 10
no shutdown
ip nat outside
exit
interface gigabit 0/0
no ip address
pppoe enable
pppoe-client dial-pool-number 10
no shutdown
exit
exit
interface gigabit 0/1
ip address 192.168.0.254 255.255.255.0
no shutdown
ip nat inside
exit
ip access-list standard NAT_ADDRESSES
permit 192.168.0.0 0.0.0.255
exit
ip nat inside source list NAT_ADDRESSES interface dialer 1

Cisco router 2901 Shutdown after 30 or 50 min

Hi All,
Anybody suggest me why router going to shut down mode after 15 or 30 min? Here is the #show tech support command. Please find the attached document.
Rgs.....
Parosh

hi
Shutdown mode means shutdown. When I connect console there have no error or log message.
Thanks for reply.
Rgs..
Parosh

Unable to use Cisco Router 2851 as E1 RAS. Please help...

Dear All,
I have one Cisco Router 2851 with following cards and features:
Cisco 2851-V/K9 - 2851 Voice Bundle
VWIC2-2MFT-T1/E1 - 2-Port 2nd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1
S28NSPSK9 - 12403 - IOS
PWR-2821-51-AC - 1 No
Router-SDM-CD - 1 No
PVDM2-48 - 1 No
MEM2800-256D-INC - 1 No
MEM2800-64-CF-INC - 1 No
ACS-2821-51-STAN - 1 No
Attaching Config details along with this.
Appreciate, if someone help me on this.
Regards,
Suresh

You need a digital modems card for that, PVDM2-xxDM, where xx = 12, 24 or 36.
You will also need one of the following interface cards:
NM-1CE1T1-PRI
NM-2CE1T1-PRI
HWIC-1CE1T1-PRI
HWIC-2CE1T1-PRI
The VWIC that you have is not supported with the Digital Modems.

Voice Bundle Routers vs UC Bundle Routers

Hello all,
I am techinal engineer, but i need to make BoQ for 3945 CME-SRST for one of our client.
In Cisco Commerce Workspace i can see there are two types of 3945 routers are available for CME SRST
1- C3945-CME-SRST/K9 = 3945 Voice Bundle w/PVDM3-64,FL-CME-SRST-25,UC Lic,FL-CUBE25
2- C3945-CMESRSTK9-RF = 3945 UC Bun PVDM3-64, FL-CME-SRST-25, UC Lic PAK REFURBISHED
What is the difference between both, a part from this that option 2 is refurbished router, is there any other differ between both products ?
My client has 120 Users on site & i need to make BoQ that cover 120 users.
Also what is the difference between C3945 & C3945E product ?
Regards,

Basically these two bundles are same - UC/Voice bundles...exept that option one have free CUBE licenses which Cisco from near past included in voice bundles - because of obvious SIP popularity. So if I'm on your place - I would go with option 1.
3945 vs 3945E - maybe this will help:
https://supportforums.cisco.com/sites/default/files/legacy/0/5/3/78350-white_paper_c11_595485.pdf
Offcourse you can suspect which platform is more powerfull
HTH,
Dragan

Help with Remote access VPN on Cisco router 3925 via Dialer Interface

Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
        quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
Thanks

Hi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0         192.168.1.1     YES NVRAM up                    up
GigabitEthernet0/1         unassigned      YES NVRAM up                    up
GigabitEthernet0/2         unassigned      YES NVRAM up                    up
Dialer1                    210.245.54.49   YES IPCP   up                    up
Dialer2                    101.99.7.73     YES IPCP   up                    up
NVI0                       192.168.1.1     YES unset up                    up
Virtual-Access1            unassigned      YES unset up                    up
Virtual-Access2            unassigned      YES unset up                    up
Virtual-Access3            unassigned      YES unset up                    up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much !

Trouble connecting Cisco router with cable modem for Internet purposes

So I am requesting help from the Cisco community on this issue as the cable company states there equipment is working fine. At all my facilities I have a guest Internet service setup through a local Internet provide to provide Internet services to the residents and guests. I have the cable modem usually a Motorola SBG6580 or a SMC 8014 (both provided by cable company) connected to my router on a FE or GE interface. I am using static IPs and using the cable modem just as a modem (bridge mode). Over the past several months these connections have just stopped working. I have not made any drastic changes to my router configs; however, the cable company has updated the firmware on these modems. I am wondering if that could affected how the modem and router talk. I was told by the cable company that the modem sees the Cisco router but that the port is inactive. My router shows the port is active and traffic passing. Does anyone have any ideas that could point where the problem lies? I will post a basic config to one that currently does not work. I am using a VRF to route a certain group out, using NAT. Please let me know if I need to post additional info. Any help would be greatly appreciated.
Cisco CISCO2911/K9
Version 15.2(3)T1
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1204RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-3.T.bin
boot-end-marker
card type t1 0 0
logging buffered 64000
aaa new-model
aaa session-id common
clock timezone cst -6 0
clock summer-time CDT recurring
no ipv6 cef
no ip source-route
ip vrf 5
rd 5:1
ip multicast-routing
1
ip dhcp pool Guest
vrf 5
network 10.51.XXX.0 255.255.255.0
default-router 10.51.XXX.XXX
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
multilink bundle-name authenticated
application
global
service alternate default
license udi pid CISCO2911/K9 sn FTX1508AHTM
hw-module pvdm 0/0
redundancy
ip tcp synwait-time 10
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding 5
ip address 10.51.xx.xxx 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/2
description Guest Intenet access
ip vrf forwarding 5
ip address 24.242.182.182 255.255.255.252   <--Cable company IP, Modem IP is 24.242.182.181
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
no ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 9 interface GigabitEthernet0/2 vrf 5 overload
ip route vrf 5 0.0.0.0 0.0.0.0 24.242.182.181
access-list 9 permit 10.51.204.0 0.0.0.255

Ok, mysteriously this location just started working yesterday, but I still am dealing with seven others and I really would like to know what is going on. I will give you everything you may need and let me know.
Config:
version 15.2
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname 1112RTR01
boot-start-marker
boot system flash0:c2900-universalk9-mz.SPA.152-3.T1.bin
boot system flash0:c2900-universalk9-mz.SPA.151-1.T.bin
boot-end-marker
aaa new-model
aaa session-id common
clock timezone CDT -6 0
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
no ip source-route
ip vrf GuestVRF
rd 5:1
ip multicast-routing
ip dhcp pool Guest
vrf GuestVRF
network 10.51.112.0 255.255.255.0
default-router 10.51.112.1
dns-server 209.18.47.61 209.18.47.62
ip flow-cache timeout active 1
no ip bootp server
no ip domain lookup
ip cef
application
global
service alternate default
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0.5
description Guest VLAN
encapsulation dot1Q 5
ip vrf forwarding GuestVRF
ip address 10.51.112.1 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
interface GigabitEthernet0/1
description Guest Internet (Time Warner Connection)
ip vrf forwarding GuestVRF
ip address 97.77.116.234 255.255.255.252
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
ip forward-protocol nd
ip nat inside source list 5 interface GigabitEthernet0/1 vrf GuestVRF overload
ip route vrf GuestVRF 0.0.0.0 0.0.0.0 97.77.116.233
access-list 5 permit 10.51.112.0 0.0.0.255
control-plane
end
router#sh ip arp vrf GuestVRF
router#Internet 97.77.116.233           2   f80b.bee7.e09f ARPA   GigabitEthernet0/1
Protocol Address          Age (min) Hardware Addr   Type   Interface
Internet 97.77.116.234           -   8843.e13c.8d99 ARPA   GigabitEthernet0/1
router#ping vrf GuestVRF 97.77.116.233
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 97.77.116.233, timeout is 2 seconds:
Success rate is 0 percent (0/5)
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:10
Input queue: 76/75/15/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
     81 packets input, 4860 bytes, 0 no buffer
     Received 81 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 12 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     16 packets output, 1193 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out
router#sh int g0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is CN Gigabit Ethernet, address is 8843.e13c.8d99 (bia 8843.e13c.8d99)
Description: Guest Internet (Time Warner Connection)
Internet address is 97.77.116.234/30
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is RJ45
output flow-control is XON, input flow-control is XON
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:42
Input queue: 76/75/67/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
30 second input rate 3000 bits/sec, 7 packets/sec
30 second output rate 1000 bits/sec, 2 packets/sec
     408 packets input, 24480 bytes, 0 no buffer
     Received 408 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 61 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast, 0 pause input
     72 packets output, 5669 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 pause output
     0 output buffer failures, 0 output buffers swapped out
I am receiving packets in and out of the interface but I cannot ping the modem through the VRF.
router#sh ip nat translations
Pro Inside global      Inside local       Outside local      Outside global
udp 97.77.116.234:3169 10.51.112.39:3169 209.18.47.62:53    209.18.47.62:53
udp 97.77.116.234:8534 10.51.112.39:8534 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:12244 10.51.112.39:12244 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:14002 10.51.112.39:14002 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:23623 10.51.112.39:23623 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:24489 10.51.112.39:24489 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:24550 10.51.112.39:24550 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:27458 10.51.112.39:27458 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:28603 10.51.112.39:28603 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:37404 10.51.112.39:37404 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:53942 10.51.112.39:53942 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:58125 10.51.112.39:58125 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:64797 10.51.112.39:64797 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:56925 10.51.112.52:56925 209.18.47.62:53   209.18.47.62:53
udp 97.77.116.234:62342 10.51.112.52:62342 209.18.47.62:53   209.18.47.62:53
tcp 97.77.116.234:36559 10.51.112.69:36559 199.167.177.46:1227 199.167.177.46:1227
tcp 97.77.116.234:48895 10.51.112.69:48895 54.195.253.126:5223 54.195.253.126:5223
tcp 97.77.116.234:58385 10.51.112.69:58385 54.195.243.137:5223 54.195.243.137:5223
Pro Inside global      Inside local       Outside local      Outside global
tcp 97.77.116.234:58658 10.51.112.71:58658 31.13.66.165:443 31.13.66.165:443
udp 97.77.116.234:3066 10.51.112.72:3066 209.18.47.62:53    209.18.47.62:53
udp 97.77.116.234:3884 10.51.112.72:3884 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:6656 10.51.112.72:6656 209.18.47.61:53    209.18.47.61:53
udp 97.77.116.234:11194 10.51.112.72:11194 209.18.47.61:53   209.18.47.61:53
udp 97.77.116.234:11774 10.51.112.72:11774 209.18.47.62:53   209.18.47.62:53
Let me know if you need anything else. I need to figure this out and I just don't get it because the other site wasn't working a few days ago and all of a sudden it is working again but others are still not.

Cisco router 877M capability to use Unified Communications technology?

Hi all,
Can Cisco router 877M have the features or capability to use VOIP or Unified Communications technology?
Cheers,

Hi Tai,
You may want to take a look at the 2800 series routers. There are bundles to support the number of users you currently have.
If you were to install a 2800 series at your headquarters your remote sites could VPN to headquarters and receive their phone service from headquarters.
Doing this will eliminate any toll charges for calls between the offices.
There is the need to maintain connections to the PSTN in case you lose your WAN connection you will maintain telephony services utilizing the PSTN.
At your remote sites you may want to consider the 880 series routers which have a provision for Survivable remote site telephony (SRST).
This feature allows the router at the remote site to maintain call management if the remote site loses the WAN connection to headquarters.
These calls would then be automatically routed through the PSTN until the WAN connection is restored.
The savings from eliminating charges for calls between your sites may justify the purchase of the new technology.
I would suggest you do a cost study to see how much you spend monthly on calls between the offices.
Hope this helps.
Mark

Cisco router interface threshold

Hello,
I have a question about getting threshold information out of a specific interface. I have a customer with DSL on a cisco 887 router.
This customer has 2 different pvc's on the ATM0 interface, 2 dialer's (1 for voice, one for data) 2 vlan's (1 for voice, one for data).
What I would like is that the cisco router wil send me a message that only the voice dialer or voice vlan has exceeded it's threshold limit.
I can configure this with the "rmon alarm" command, but then it isn't specific for the voice dialer, it gives me info on both the dialers.
I also tried it with SNMP traps, but this isn't "real-time"
Does anyone know if there is a different solution to solve this?

Sorry, small mistake :-)
Heres my configuration:
event manager applet int-rate-test
event interface name Dialer1 parameter receive_rate_bps entry-op gt entry-val 110000 entry-type rate exit-op lt exit-val 50000 exit-type rate average-factor 1 poll-interval 1
snmp-server community G***** RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps vrrp
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps license
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps flash insertion removal
snmp-server enable traps adslline
snmp-server enable traps vdsl2line
snmp-server enable traps envmon
snmp-server enable traps c3g
snmp-server enable traps isdn call-information
snmp-server enable traps isdn layer2
snmp-server enable traps isdn chan-not-avail
snmp-server enable traps isdn ietf
snmp-server enable traps mac-notification
snmp-server enable traps energywise
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps aaa_server
snmp-server enable traps atm subif
snmp-server enable traps bfd
snmp-server enable traps memory bufferpeak
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps entity
snmp-server enable traps fru-ctrl
snmp-server enable traps resource-policy
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps msdp
snmp-server enable traps mvpn
snmp-server enable traps cpu threshold
snmp-server enable traps ipsla
snmp-server enable traps syslog
snmp-server enable traps l2tun session
snmp-server enable traps l2tun pseudowire status
snmp-server enable traps vtp
snmp-server enable traps pw vc
snmp-server enable traps firewall serverstatus
snmp-server enable traps nhrp nhs
snmp-server enable traps nhrp nhc
snmp-server enable traps nhrp nhp
snmp-server enable traps nhrp quota-exceeded
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *.*.*.30 G****
interface Dialer1
description tbv Internet KPN-lijn
ip address negotiated
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname test-vdsl-inet
ppp chap password 7 051F031C3501580D0A095A1B050910
ppp pap sent-username test-vdsl-inet password 7 111D1C16035F1D081726662D263621
no cdp enable
When I download something from the internet it only shows the interface bandwidth usage stats every 5min. I'm not getting any event messages to my Zenoss server that a threshold has been reached or anything like that.
I have attached a file with the results.

Does anyone configure cisco router with MGCP to link Call agent Clarent ?

hi,
We require to configure As5300 with MGCP to link Clarent call agent. Does anyone have cisco router configuration ?
thanks.
best regards.
fred.

Below is the sample configuration for the 5300 to Call-Agent. This is also dependant on which package is configured on the call-agent so we can configure it accordingly. Hope this helps.
version 12.3
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AS5300-5
boot system tftp c5300-is-mz.123-2.T1 171.68.191.135
logging buffered 100000 debugging
enable password xxxx
backhaul-session-manager
set bh5300-vsc1 client nft
group bhgrp1 set bh5300-vsc1
session group bhgrp1 172.16.20.35 7007 172.16.20.28 7007 0
isdn switch-type primary-ni
isdn voice-call-failure 0
no scripting tcl init
no scripting tcl encdir
voice call carrier capacity active
voice class codec 1
codec preference 1 g723r63
codec preference 2 g711ulaw
no voice hpi capture buffer
no voice hpi capture destination
dial-control-mib retain-timer 240
dial-control-mib max-size 600
controller T1 0
framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24 service mgcp
controller T1 1
framing esf
clock source line secondary 1
linecode b8zs
ds0-group 0 timeslots 1-24 type none service mgcp
controller T1 2
framing esf
clock source line secondary 2
linecode b8zs
controller T1 3
framing esf
clock source line secondary 3
linecode b8zs
interface Ethernet0
no ip address
no ip mroute-cache
shutdown
interface Serial0
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial1
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial2
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial3
no ip address
no ip mroute-cache
shutdown
clockrate 2015232
no fair-queue
interface Serial0:23
no ip address
isdn switch-type primary-ni
isdn bind-l3 backhaul bh5300-vsc1
no cdp enable
interface FastEthernet0
ip address 172.16.20.28 255.255.255.192
no ip mroute-cache
duplex full
speed auto
no cdp enable
ip classless
ip route 0.0.0.0 0.0.0.0 172.16.20.1
no ip http server
radius-server host 172.21.59.165 auth-port 1645 acct-port 1646
radius-server key xxxxxxxx
radius-server vsa send accounting
voice-port 0:23
voice-port 1:0
mgcp
mgcp call-agent 172.16.20.35 2427 service-type mgcp version 0.1
mgcp quarantine mode loop
mgcp package-capability dtmf-package
mgcp package-capability rtp-package
mgcp package-capability as-package
mgcp default-package gm-package
mgcp profile default
timeout tsmax 100
no max1 lookup
dial-peer cor custom

When upgrade ddr ram in a voice bundle 2821 ?

hi,
i want to buy a 2821 voice bundle with a upgrade to 64 pvdm and 256 ddr ram.
the router will have two e1, when is necesary tu upgrade the ddr ram memory ?

No, I never seen that necessary for ISR routers.

Cisco Router tried to take a firmware update and no longer works

Ok so internet was working fine until Cisco Connect told me to take an update. My connection is wired and there were no disruptions during the download. Yet the download still failed and now my power light blinks continuously and there is no internet access. I tried instructions on "How to unbrick your Cisco Router", even got them to work, it took the firmware update from the cmd line. Still doesnt work though. What's wrong with this thing and how do i fix it?
Solved!
Go to Solution.

I ended up downloading a firmware utility program and was able to get it to reload. The power light became solid somewhere between 2-5 mins, however still didnt connect to the internet. Found that all this factory resetting will change your Internet access name & password, with no way to find out the new one. You have to remove the Cisco Connect program from your computer and reload it from the original disk. Only then will you be up and running again. While I appreciate the response Helm, I was way beyond a 30 second reset button solution when I posted this lol.

Cant ping behind cisco router (site2site vpn)

Dears;
After configure site to site vpn between cisco router and fortigate firewall,
site A : 10.0.0.0/24     behind fortigate
site B: 10.10.10.0/24 behind cisco router
the tunnel is up and I can ping 10.0.0.1 from site B and can ping 10.10.10.1 from site A but I cant ping any ip inside 10.0.0.0/24 form site B or network 10.10.10.0/24 from site A
my cisco router configuration is
Current configuration : 2947 bytes
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
boot-start-marker
boot-end-marker
enable secret 4 EE103as6FtdocdBefpgugX6P9eGaDKDyBvwz7AywH5Q
no aaa new-model
memory-size iomem 10
clock timezone cairo 2 0
crypto pki token default removal timeout 0
ip source-route
ip dhcp excluded-address 192.168.16.1
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp pool GUEST
network 192.168.16.0 255.255.255.0
default-router 192.168.16.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool LAN
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 8.8.8.8 8.8.4.4
ip cef
controller VDSL 0
ip ssh version 2
crypto isakmp policy 10
encr aes
hash sha256
authentication pre-share
group 5
crypto isakmp key 6 *********** address 4.x.x.x no-xauth
crypto ipsec transform-set myset esp-aes esp-sha256-hmac
crypto map kon-map 10 ipsec-isakmp
set peer 4.x.x.x
set transform-set myset
set pfs group5
match address 105
interface Ethernet0
no ip address
no fair-queue
interface ATM0
no ip address
ip mtu 1452
ip tcp adjust-mss 1452
no atm ilmi-keepalive
interface ATM0.1 point-to-point
ip flow ingress
pvc 0/35
encapsulation aal5snap
pppoe-client dial-pool-number 1
interface FastEthernet0
switchport mode trunk
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
switchport access vlan 2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface Vlan2
ip address 192.168.16.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp authentication chap pap callin
ppp chap hostname
ppp chap password 0
ppp pap sent-username
crypto map kon-map
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
access-list 100 deny   ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
access-list 100 permit ip 10.10.10.0 0.0.0.255 any
access-list 100 permit ip 192.168.16.0 0.0.0.255 any
access-list 105 permit ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
banner motd ^C^C
end
when ping from cisco router
konsuler#ping 10.0.0.27 source vlan1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.27, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
Success rate is 0 percent (0/5)
help please

Thank you karsten
I can ping interface of router from remote site but cant ping any device behind the router and can ping firewall interface but cant ping any device behind the firewall
-counters in
# sh crypto ipsec sa
increased only while ping 10.0.0.1 or 10.10.10.1 from both sides
r#show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: Dialer1
Uptime: 00:03:12
Session status: UP-ACTIVE
Peer: 4.x.x.x port 500 fvrf: (none) ivrf: (none)
      Phase1_id: 4.x.x.x
      Desc: (none)
IKEv1 SA: local 6.x.x.x/500 remote 4.x.x.x/500 Active
          Capabilities:(none) connid:2001 lifetime:22:39:59
IPSEC FLOW: permit ip 10.10.10.0/255.255.255.0 10.0.0.0/255.255.255.0
        Active SAs: 2, origin: crypto map
        Inbound: #pkts dec'ed 9 drop 0 life (KB/Sec) 4605776/3407
        Outbound: #pkts enc'ed 14 drop 0 life (KB/Sec) 4605775/3407

Not able to telnet or ssh to outside interface of ASA and Cisco Router

Dear All
Please help me with following question, I have set up testing lab, but still not work.
it is Hub and spoke site to site vpn case, connection between hub and spoke is metro-E, so we are using private ip for outside interface at each site.
Hub -- Juniper SRX
Spoke One - Cisco ASA with version 9.1(5)
spoke two - Cisco router with version 12.3
site to site vpn has been successful established. Customer would like to telnet/ssh to spoke's outside ip from Hub(using Hub's outside interface as source for telnet/ssh), or vise versa. Reason for setting up like this is they wants to be able to make configuration change even when site to site vpn is down. Sound like a easy job to do, I tried for a long time, search this forum and google too, but still not work.
Now I can successfully telnet/ssh to Hub SRX's outside interface from spoke (ASA has no telnet/ssh client, tested using Cisco router).
Anyone has ever done it before, please help to share your exp. Does Cisco ASA or router even support it?
When I tested it, of cause site to site vpn still up and running.
Thanks
YK

Hello YK,
On this case on the ASA, you should have the following:
CConfiguring Management Access Over a VPN Tunnel
If your VPN tunnel terminates on one interface, but you want to manage the ASA by accessing a different interface, you can identify that interface as a management-access interface. For example, if you enter the ASA from the outside interface, this feature lets you connect to the inside interface using ASDM, SSH, Telnet, or SNMP; or you can ping the inside interface when entering from the outside interface. Management access is available via the following VPN tunnel types: IPsec clients, IPsec LAN-to-LAN, and the AnyConnect SSL VPN client.
To specify an interface as a mangement-only interface, enter the following command:
hostname(config)# management access management_interface
where management_interface specifies the name of the management interface you want to access when entering the security appliance from another interface.
You can define only one management-access interface
Also make sure you have the pertinent configuration for SSH, telnet, ASDM and SNMP(if required), for a quick test you can enable on your lab Test:
SSH
- ssh 0 0 outside
- aaa authentication ssh console LOCAL
- Make sure you have a default RSA key, or create a new one either ways, with this command:
*crypto key generate rsa modulus 2048
Telnet
- telnet 0 0 outside
- aaa authentication telnet console LOCAL
Afterwards, if this works you can define the subnets that should be permitted.
On the router:
!--- Step 1: Configure the hostname if you have not previously done so.
hostname Router
!--- aaa new-model causes the local username and password on the router
!--- to be used in the absence of other AAA statements.
aaa new-model
username cisco password 0 cisco
!--- Step 2: Configure the router's DNS domain.
ip domain-name yourdomain.com
!--- Step 3: Generate an SSH key to be used with SSH.
crypto key generate rsa
ip ssh time-out 60
ip ssh authentication-retries 3
!--- Step 4: By default the vtys' transport is Telnet. In this case,
!--- Telnet and SSH is supported with transport input all
line vty 0 4
transport input All
*!--- Instead of aaa new-model, the login local command may be used.
no aaa new-model
line vty 0 4
login local
Let me know how it works out!
Please don't forget to Rate and mark as correct the helpful Post!
David Castro,
Regards,

Remote access VPN with Cisco Router - Can not get the Internal Lan .

Dear Sir ,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Below is the IP address of the device.
Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
IP address:10.10.10.1
Mask:255.255.255.0 F0/0
IP Address :20.20.20.1
Mask :255.255.255.0
F0/1
IP address :192.168.1.3
Mask:255.255.255.0
F0/0
IP address :20.20.20.2
Mask :255.255.255.0
F0/1
IP address :192.168.1.1
Mask:255.255.255.0
I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
Need your help to fix the problem.
Router R2 Configuration :!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R2
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip tcp synwait-time 5
interface FastEthernet0/0
ip address 20.20.20.2 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Router R1 Configuration :
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login USERAUTH local
aaa authorization network NETAUTHORIZE local
aaa session-id common
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
username vpnuser password 0 strongpassword
ip tcp synwait-time 5
crypto keyring vpnclientskey
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group remotevpn
key cisco123
dns 192.168.1.2
wins 192.168.1.2
domain mycompany.com
pool vpnpool
acl VPN-ACL
crypto isakmp profile remoteclients
description remote access vpn clients
keyring vpnclientskey
match identity group remotevpn
client authentication list USERAUTH
isakmp authorization list NETAUTHORIZE
client configuration address respond
crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
crypto dynamic-map DYNMAP 10
set transform-set TRSET
set isakmp-profile remoteclients
crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPNMAP
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip local pool vpnpool 192.168.50.1 192.168.50.10
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
no ip http server
no ip http secure-server
ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
ip access-list extended NAT-ACL
deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended VPN-ACL
permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
end

Dear All,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Waiting for your responce .
--Milon

Cisco Router 2901,voice bundle 4FXO

Similar Messages

Maybe you are looking for