Cisco router interface threshold

Hello,
I have a question about getting threshold information out of a specific interface. I have a customer with DSL on a cisco 887 router.
This customer has 2 different pvc's on the ATM0 interface, 2 dialer's (1 for voice, one for data) 2 vlan's (1 for voice, one for data).
What I would like is that the cisco router wil send me a message that only the voice dialer or voice vlan has exceeded it's threshold limit.
I can configure this with the "rmon alarm" command, but then it isn't specific for the voice dialer, it gives me info on both the dialers.
I also tried it with SNMP traps, but this isn't "real-time"
Does anyone know if there is a different solution to solve this?

Sorry, small mistake :-)
Heres my configuration:
event manager applet int-rate-test
event interface name Dialer1 parameter receive_rate_bps entry-op gt entry-val 110000 entry-type rate exit-op lt exit-val 50000 exit-type rate average-factor 1 poll-interval 1
snmp-server community G***** RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps vrrp
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps license
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps flash insertion removal
snmp-server enable traps adslline
snmp-server enable traps vdsl2line
snmp-server enable traps envmon
snmp-server enable traps c3g
snmp-server enable traps isdn call-information
snmp-server enable traps isdn layer2
snmp-server enable traps isdn chan-not-avail
snmp-server enable traps isdn ietf
snmp-server enable traps mac-notification
snmp-server enable traps energywise
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps aaa_server
snmp-server enable traps atm subif
snmp-server enable traps bfd
snmp-server enable traps memory bufferpeak
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps entity
snmp-server enable traps fru-ctrl
snmp-server enable traps resource-policy
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps msdp
snmp-server enable traps mvpn
snmp-server enable traps cpu threshold
snmp-server enable traps ipsla
snmp-server enable traps syslog
snmp-server enable traps l2tun session
snmp-server enable traps l2tun pseudowire status
snmp-server enable traps vtp
snmp-server enable traps pw vc
snmp-server enable traps firewall serverstatus
snmp-server enable traps nhrp nhs
snmp-server enable traps nhrp nhc
snmp-server enable traps nhrp nhp
snmp-server enable traps nhrp quota-exceeded
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *.*.*.30 G****
interface Dialer1
description tbv Internet KPN-lijn
ip address negotiated
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname test-vdsl-inet
ppp chap password 7 051F031C3501580D0A095A1B050910
ppp pap sent-username test-vdsl-inet password 7 111D1C16035F1D081726662D263621
no cdp enable
When I download something from the internet it only shows the interface bandwidth usage stats every 5min. I'm not getting any event messages to my Zenoss server that a threshold has been reached or anything like that.
I have attached a file with the results.

Similar Messages

Not able to telnet or ssh to outside interface of ASA and Cisco Router

Dear All
Please help me with following question, I have set up testing lab, but still not work.
it is Hub and spoke site to site vpn case, connection between hub and spoke is metro-E, so we are using private ip for outside interface at each site.
Hub -- Juniper SRX
Spoke One - Cisco ASA with version 9.1(5)
spoke two - Cisco router with version 12.3
site to site vpn has been successful established. Customer would like to telnet/ssh to spoke's outside ip from Hub(using Hub's outside interface as source for telnet/ssh), or vise versa. Reason for setting up like this is they wants to be able to make configuration change even when site to site vpn is down. Sound like a easy job to do, I tried for a long time, search this forum and google too, but still not work.
Now I can successfully telnet/ssh to Hub SRX's outside interface from spoke (ASA has no telnet/ssh client, tested using Cisco router).
Anyone has ever done it before, please help to share your exp. Does Cisco ASA or router even support it?
When I tested it, of cause site to site vpn still up and running.
Thanks
YK

Hello YK,
On this case on the ASA, you should have the following:
CConfiguring Management Access Over a VPN Tunnel
If your VPN tunnel terminates on one interface, but you want to manage the ASA by accessing a different interface, you can identify that interface as a management-access interface. For example, if you enter the ASA from the outside interface, this feature lets you connect to the inside interface using ASDM, SSH, Telnet, or SNMP; or you can ping the inside interface when entering from the outside interface. Management access is available via the following VPN tunnel types: IPsec clients, IPsec LAN-to-LAN, and the AnyConnect SSL VPN client.
To specify an interface as a mangement-only interface, enter the following command:
hostname(config)# management access management_interface
where management_interface specifies the name of the management interface you want to access when entering the security appliance from another interface.
You can define only one management-access interface
Also make sure you have the pertinent configuration for SSH, telnet, ASDM and SNMP(if required), for a quick test you can enable on your lab Test:
SSH
- ssh 0 0 outside
- aaa authentication ssh console LOCAL
- Make sure you have a default RSA key, or create a new one either ways, with this command:
*crypto key generate rsa modulus 2048
Telnet
- telnet 0 0 outside
- aaa authentication telnet console LOCAL
Afterwards, if this works you can define the subnets that should be permitted.
On the router:
!--- Step 1: Configure the hostname if you have not previously done so.
hostname Router
!--- aaa new-model causes the local username and password on the router
!--- to be used in the absence of other AAA statements.
aaa new-model
username cisco password 0 cisco
!--- Step 2: Configure the router's DNS domain.
ip domain-name yourdomain.com
!--- Step 3: Generate an SSH key to be used with SSH.
crypto key generate rsa
ip ssh time-out 60
ip ssh authentication-retries 3
!--- Step 4: By default the vtys' transport is Telnet. In this case,
!--- Telnet and SSH is supported with transport input all
line vty 0 4
transport input All
*!--- Instead of aaa new-model, the login local command may be used.
no aaa new-model
line vty 0 4
login local
Let me know how it works out!
Please don't forget to Rate and mark as correct the helpful Post!
David Castro,
Regards,

How to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

how to configure one dsl connection and one public ip in cisco router and map to one interface for using exchange server

Hi ,
Have you got any additional public IP Address from your service provider , If yes on router you can have static route for those additional IP Address pointing to your ASA outside interface .
Accordingly you can configure NAT
HTH
Sandy .

Help with Remote access VPN on Cisco router 3925 via Dialer Interface

Hi Everybody,
I need help for my work now, I appreciate if someone can fix my problem.I have a Cisco router 3925 and access Internet via PPPoE link. I want config VPN Remote Access and using software Cisco VPN client. But it doesn't work.. Here my config router :
HUNRE#show running-config
Building configuration...
Current configuration : 5515 bytes
! No configuration change since last restart
version 15.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname HUNRE
boot-start-marker
boot-end-marker
enable secret 5 $1$vEFw$rLfvLglzUgddCVwXDx03K.
enable password cisco
aaa new-model
aaa session-id common
crypto pki trustpoint TP-self-signed-1050416327
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1050416327
revocation-check none
rsakeypair TP-self-signed-1050416327
crypto pki certificate chain TP-self-signed-1050416327
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31303530 34313633 3237301E 170D3134 30393235 31313534
31395A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 30353034
31363332 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100CC79 74FCFABE 81183B70 5A9F4A53 EB609754 7D5F8587 9150B76E 3207A86E
5B65F9E9 6CDAC21A 6D69221D 1FF61632 14763308 43B2A1CC 8EE5ABAC EF07530E
3F0D35FE F08C955B 60B52B92 F8F54D53 DD6DD623 01F83493 02F9C49A F0C3483D
3B48A008 8D96700E 88924BFE DE00201B DE5965DE 32898CAD 9012AB55 76B6F39B
2D470203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 14C3418C BC35F3D9 B26B2475 2BB5F826 060525AB B3301D06
03551D0E 04160414 C3418CBC 35F3D9B2 6B24752B B5F82606 0525ABB3 300D0609
2A864886 F70D0101 05050003 81810070 AC7C26C6 4606A551 1A3FD6C5 2A5AEAE8
35DAC86E F8885E26 51F6EEAE 7565D3AA D532C8F3 55F6656F D103F38C 8FBDE7F1
83E77143 76469040 7FEA41E8 14963DB3 F7F28EA0 C5F2F42C B186B75C AAB04900
15F9CB38 A16964F5 4E7B4378 35041AA8 AE8EC181 D58D6A62 676E286A 7B9D80E6
35A0B9FB FB76E976 3D2A19D7 006078
        quit
ip name-server 210.245.1.253
ip name-server 210.245.1.254
ip cef
no ipv6 cef
multilink bundle-name authenticated
vpdn enable
vpdn-group 1
vpdn-group 2
license udi pid C3900-SPE100/K9 sn FOC1823839B
license boot module c3900 technology-package securityk9
username cisco privilege 15 secret 5 $1$aAjB$D3iLyPFTE7O1bHPnKSJcH0
username kdhong privilege 15 secret 5 $1$nfyX$FO1BPTabCUaE6uKQwpLT.1
redundancy
track 1 ip sla 1 reachability
track 2 ip sla 2 reachability
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group VPN-HUNRE
key hunre
dns 8.8.8.8
domain hunre
pool IP-VPN
acl 199
max-users 100
crypto ipsec transform-set encrypt-method-1 esp-3des esp-sha-hmac
mode tunnel
crypto dynamic-map DYNMAP 1
set transform-set encrypt-method-1
crypto map VPN client configuration address respond
crypto map VPN 65535 ipsec-isakmp dynamic DYNMAP
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip mtu 1492
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
interface GigabitEthernet0/1
description FPT
no ip address
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface GigabitEthernet0/2
description Connect to CMC
no ip address
ip mtu 1442
ip nat outside
ip virtual-reassembly in
ip tcp adjust-mss 1412
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
no cdp enable
interface Dialer1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp dns request
crypto map VPN
interface Dialer2
description Logical ADSL Interface 2
ip address negotiated
ip mtu 1442
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1344
dialer pool 2
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname [USERNAME]
ppp chap password 0 [PASSWORD]
ppp pap sent-username [USERNAME] password 0 [PASSWORD]
ppp ipcp address accept
no cdp enable
ip local pool IP-VPN 10.252.252.2 10.252.252.245
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list 11 interface Dialer2 overload
ip nat inside source static 10.159.217.10 interface Dialer1
ip nat inside source list 199 interface Dialer1 overload
ip nat inside source static tcp 10.159.217.10 80 210.245.54.49 80 extendable
ip nat inside source static tcp 10.159.217.10 3389 210.245.54.49 3389 extendable
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.159.217.0 255.255.255.0 192.168.1.8
ip sla auto discovery
ip sla responder
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
access-list 10 permit any
access-list 11 permit any
access-list 101 permit icmp any any
access-list 199 permit ip any any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
transport input all
line vty 5 15
password cisco
transport input all
scheduler allocate 20000 1000
ntp master
end
However, I cannot ping interfac Dialer 1. I using Cisco vpn client software ver 5.0.07.0290.
Hopeful for your answers !
Thanks

Hi David Castro,
Thanks for your answer,
I configed following your guide, but it have not worked yet. I saw that I cannot ping IP gateway Internet . I using ADSL Internet and config PPPoE and my router receive IP from ISP. Here show ip int brief :
GigabitEthernet0/0         192.168.1.1     YES NVRAM up                    up
GigabitEthernet0/1         unassigned      YES NVRAM up                    up
GigabitEthernet0/2         unassigned      YES NVRAM up                    up
Dialer1                    210.245.54.49   YES IPCP   up                    up
Dialer2                    101.99.7.73     YES IPCP   up                    up
NVI0                       192.168.1.1     YES unset up                    up
Virtual-Access1            unassigned      YES unset up                    up
Virtual-Access2            unassigned      YES unset up                    up
Virtual-Access3            unassigned      YES unset up                    up
But I cannot ping Interface Dialer 1, so may be VPN is does not worked. Do you have some ideal ?
Thanks very much !

How to create custom GUI interface for Cisco router?

Hello,
I am working on a Cisco solution and I have my router configured for the solution I need. However, if a non-cisco person needs to use my solution then I think he will need a GUI interface which will have few "buttons" which when clicked will run some Cisco commands on Cisco router to make it work. Is there a way to design such GUI interface which is compatible with Cisco routers? I know Cisco has SDM, but that is too involved and detailed, which is useful only for people who know atleast a little bit about Cisco. Here I am looking at crowd who will have 0 knowledge of Cisco.
Please let me know if something like this can be done. If yes, how and how easily?
Thank you.

There are lots of ways to do this - you can use SNMP or even HTTP to push or pull commands from Cisco devices. How easy it is to create a GUI depends on your programming skills. I would guess a simple web page triggering backend scripts would be the easiest way to do this.

Cisco Router 12406 MPLS physical interface problem!

I want to monitor a router interface with a NMS program, but i can't collect the data from this interface.
I was trying with:
snmpwalk -v2c -c community 10.100.xxx.xx 1.3.6.1.2.1.2.2.1.19 the result was that is missing the oid named ifOutDiscards for the interface that i want to monitor.
How can i fix this problem?

Hello Flo,
what kind of interface is this ? is it a POS Sonet/SDH interface?
my guess is that ifOutDiscards may be related to LAN type interfaces
"The number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent
their being transmitted. One possible reason for discarding
such a packet could be to free up buffer space.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ifCounterDiscontinuityTime."
Actually from description it looks like the variable should apply also to POS interfaces
see
http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.2.1.2.2.1.19&translate=Translate&submitValue=SUBMIT
you can also check the supporting images from the link above
Hope to help
Giuseppe

Cant ping behind cisco router (site2site vpn)

Dears;
After configure site to site vpn between cisco router and fortigate firewall,
site A : 10.0.0.0/24     behind fortigate
site B: 10.10.10.0/24 behind cisco router
the tunnel is up and I can ping 10.0.0.1 from site B and can ping 10.10.10.1 from site A but I cant ping any ip inside 10.0.0.0/24 form site B or network 10.10.10.0/24 from site A
my cisco router configuration is
Current configuration : 2947 bytes
! No configuration change since last restart
version 15.1
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
boot-start-marker
boot-end-marker
enable secret 4 EE103as6FtdocdBefpgugX6P9eGaDKDyBvwz7AywH5Q
no aaa new-model
memory-size iomem 10
clock timezone cairo 2 0
crypto pki token default removal timeout 0
ip source-route
ip dhcp excluded-address 192.168.16.1
ip dhcp excluded-address 10.10.10.1 10.10.10.10
ip dhcp pool GUEST
network 192.168.16.0 255.255.255.0
default-router 192.168.16.1
dns-server 8.8.8.8 8.8.4.4
ip dhcp pool LAN
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 8.8.8.8 8.8.4.4
ip cef
controller VDSL 0
ip ssh version 2
crypto isakmp policy 10
encr aes
hash sha256
authentication pre-share
group 5
crypto isakmp key 6 *********** address 4.x.x.x no-xauth
crypto ipsec transform-set myset esp-aes esp-sha256-hmac
crypto map kon-map 10 ipsec-isakmp
set peer 4.x.x.x
set transform-set myset
set pfs group5
match address 105
interface Ethernet0
no ip address
no fair-queue
interface ATM0
no ip address
ip mtu 1452
ip tcp adjust-mss 1452
no atm ilmi-keepalive
interface ATM0.1 point-to-point
ip flow ingress
pvc 0/35
encapsulation aal5snap
pppoe-client dial-pool-number 1
interface FastEthernet0
switchport mode trunk
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
switchport access vlan 2
no ip address
interface FastEthernet3
no ip address
interface Vlan1
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface Vlan2
ip address 192.168.16.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
ip virtual-reassembly in
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
ppp authentication chap pap callin
ppp chap hostname
ppp chap password 0
ppp pap sent-username
crypto map kon-map
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
access-list 100 deny   ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
access-list 100 permit ip 10.10.10.0 0.0.0.255 any
access-list 100 permit ip 192.168.16.0 0.0.0.255 any
access-list 105 permit ip 10.10.10.0 0.0.0.255 10.0.0.0 0.0.0.255
banner motd ^C^C
end
when ping from cisco router
konsuler#ping 10.0.0.27 source vlan1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.27, timeout is 2 seconds:
Packet sent with a source address of 10.10.10.1
Success rate is 0 percent (0/5)
help please

Thank you karsten
I can ping interface of router from remote site but cant ping any device behind the router and can ping firewall interface but cant ping any device behind the firewall
-counters in
# sh crypto ipsec sa
increased only while ping 10.0.0.1 or 10.10.10.1 from both sides
r#show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: Dialer1
Uptime: 00:03:12
Session status: UP-ACTIVE
Peer: 4.x.x.x port 500 fvrf: (none) ivrf: (none)
      Phase1_id: 4.x.x.x
      Desc: (none)
IKEv1 SA: local 6.x.x.x/500 remote 4.x.x.x/500 Active
          Capabilities:(none) connid:2001 lifetime:22:39:59
IPSEC FLOW: permit ip 10.10.10.0/255.255.255.0 10.0.0.0/255.255.255.0
        Active SAs: 2, origin: crypto map
        Inbound: #pkts dec'ed 9 drop 0 life (KB/Sec) 4605776/3407
        Outbound: #pkts enc'ed 14 drop 0 life (KB/Sec) 4605775/3407

Remote access VPN with Cisco Router - Can not get the Internal Lan .

Dear Sir ,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Below is the IP address of the device.
Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
IP address:10.10.10.1
Mask:255.255.255.0 F0/0
IP Address :20.20.20.1
Mask :255.255.255.0
F0/1
IP address :192.168.1.3
Mask:255.255.255.0
F0/0
IP address :20.20.20.2
Mask :255.255.255.0
F0/1
IP address :192.168.1.1
Mask:255.255.255.0
I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
Need your help to fix the problem.
Router R2 Configuration :!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R2
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip tcp synwait-time 5
interface FastEthernet0/0
ip address 20.20.20.2 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Router R1 Configuration :
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login USERAUTH local
aaa authorization network NETAUTHORIZE local
aaa session-id common
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
username vpnuser password 0 strongpassword
ip tcp synwait-time 5
crypto keyring vpnclientskey
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group remotevpn
key cisco123
dns 192.168.1.2
wins 192.168.1.2
domain mycompany.com
pool vpnpool
acl VPN-ACL
crypto isakmp profile remoteclients
description remote access vpn clients
keyring vpnclientskey
match identity group remotevpn
client authentication list USERAUTH
isakmp authorization list NETAUTHORIZE
client configuration address respond
crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
crypto dynamic-map DYNMAP 10
set transform-set TRSET
set isakmp-profile remoteclients
crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPNMAP
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip local pool vpnpool 192.168.50.1 192.168.50.10
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
no ip http server
no ip http secure-server
ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
ip access-list extended NAT-ACL
deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended VPN-ACL
permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
end

Dear All,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Waiting for your responce .
--Milon

Site-to-Site VPN between Cisco ASA 5505 (8.4) and Cisco Router (IOS 15.2)

Hi, I'm trying to create Site-to-Site VPN between Cisco ASA 5505 and Cisco Router 3945.
I've tried create configuration with and without ASA wizard, but anyway it doesn't work.
Please help me to find where is the issue.
I have two sites and would like to get access from 192.168.83.0 to 192.168.17.0
192.168.17.0 --- S1.S1.S1.S1 (IOS Router) ==================== S2.S2.S2.S2 (ASA 5505) --- 192.168.83.0
Here is my current configuration.
Thanks for your help.
IOS Configuration
version 15.2
crypto isakmp policy 1
encr aes 256
authentication pre-share
group 2
crypto isakmp key cisco address 198.0.183.225
crypto isakmp invalid-spi-recovery
crypto ipsec transform-set AES-SET esp-aes esp-sha-hmac
mode transport
crypto map static-map 1 ipsec-isakmp
set peer S2.S2.S2.S2
set transform-set AES-SET
set pfs group2
match address 100
interface GigabitEthernet0/0
ip address S1.S1.S1.S1 255.255.255.240
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map static-map
interface GigabitEthernet0/1
ip address 192.168.17.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
access-list 100 permit ip 192.168.17.0 0.0.0.255 192.168.83.0 0.0.0.255
ASA Configuration
ASA Version 8.4(3)
interface Ethernet0/0
switchport access vlan 2
interface Vlan1
nameif inside
security-level 100
ip address 192.168.83.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address S2.S2.S2.S2 255.255.255.248
ftp mode passive
same-security-traffic permit intra-interface
object network inside-network
subnet 192.168.83.0 255.255.255.0
object network datacenter
host S1.S1.S1.S1
object network datacenter-network
subnet 192.168.17.0 255.255.255.0
object network NETWORK_OBJ_192.168.83.0_24
subnet 192.168.83.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended deny ip any any log
access-list outside_cryptomap extended permit ip 192.168.83.0 255.255.255.0 object datacenter-network
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn_pool 192.168.83.200-192.168.83.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic inside-network interface
nat (inside,outside) source static inside-network inside-network destination static inside-network inside-network no-proxy-arp route-lookup
nat (inside,outside) source static inside-network inside-network destination static datacenter-network datacenter-network no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.83.0_24 NETWORK_OBJ_192.168.83.0_24 destination static datacenter-network pdatacenter-network no-proxy-arp route-lookup
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 DEFAULT_GATEWAY 1
crypto ipsec ikev1 transform-set vpn-transform-set esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set vpn-transform-set mode transport
crypto ipsec ikev1 transform-set L2L_SET esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set L2L_SET mode transport
crypto dynamic-map dyno 10 set ikev1 transform-set vpn-transform-set
crypto map vpn 1 match address outside_cryptomap
crypto map vpn 1 set pfs
crypto map vpn 1 set peer S1.S1.S1.S1
crypto map vpn 1 set ikev1 transform-set L2L_SET
crypto map vpn 20 ipsec-isakmp dynamic dyno
crypto map vpn interface outside
crypto isakmp nat-traversal 3600
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
group-policy GroupPolicy_S1.S1.S1.S1 internal
group-policy GroupPolicy_S1.S1.S1.S1 attributes
vpn-tunnel-protocol ikev1
group-policy remote_vpn_policy internal
group-policy remote_vpn_policy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec
username artem password 8xs7XK3To4s5WfTvtKAutA== nt-encrypted
username admin password rqiFSVJFung3fvFZ encrypted privilege 15
tunnel-group DefaultRAGroup general-attributes
address-pool vpn_pool
default-group-policy remote_vpn_policy
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group S1.S1.S1.S1 type ipsec-l2l
tunnel-group S1.S1.S1.S1 general-attributes
default-group-policy GroupPolicy_S1.S1.S1.S1
tunnel-group S1.S1.S1.S1 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f55f10c19a0848edd2466d08744556eb
: end

Thanks for helping me again. I really appreciate.
I don't hve any NAT-exemptions in Cisco IOS Router. Transform-set I will change soon, but I've tried with tunnel mode and it didn't work.
Maybe NAT-exemptions is the issue. Can you advice me which exemptions should be in Cisco IOS Router?
Because on Cisco ASA I guess I have everything.
Here is show crypto session detail
router(config)#do show crypto session detail
Crypto session current status
Code: C - IKE Configuration mode, D - Dead Peer Detection
K - Keepalives, N - NAT-traversal, T - cTCP encapsulation
X - IKE Extended Authentication, F - IKE Fragmentation
Interface: GigabitEthernet0/0
Session status: DOWN
Peer: 198.0.183.225 port 500 fvrf: (none) ivrf: (none)
      Desc: (none)
      Phase1_id: (none)
IPSEC FLOW: permit ip 192.168.17.0/255.255.255.0 192.168.83.0/255.255.255.0
        Active SAs: 0, origin: crypto map
        Inbound: #pkts dec'ed 0 drop 0 life (KB/Sec) 0/0
        Outbound: #pkts enc'ed 0 drop 0 life (KB/Sec) 0/0
Should I see something in crypto isakmp sa?
pp-border#sh crypto isakmp sa
IPv4 Crypto ISAKMP SA
dst             src             state          conn-id status
IPv6 Crypto ISAKMP SA
Thanks again for your help.

Extending VLANs across routed interfaces

Hello;
I'm trying to create a L3 core network. The core equipment will be Cisco 3750 enhanced. My idea is make each link between core 3750 a routed interface, with /30 IP addresses.
The problem is the customer needs some VLANs extended across the full enterprise. Is there any way to encapsulate the VLAN inside routed interface?
Thanks in advance.

I realize this thread is 5+ years old, but I feel like commenting anyway.
If you want to encapsulate the vlan across that link, you won't be able to use routed interfaces. You will need to use a layer 2 trunk(dot1q). Therefore, I wouldn't bother with the /30 addresses unless you want to monitor that specific link by IP. In that case, use a special VLAN just for those two interfaces and put your /30 addresses on the vlan interfaces.
If you want fast fail over on a layer 2 link, well then, use Rapid STP. The goal should be to get rid of those flat VLANs that span the core and switch to your original plan of routed interfaces using EIGRP or OSPF.

How to setup Guest Network Name in Cisco Router

Hello everyone!
The first. Sorry my english =)
I want tald you how to change guest network name in cisco (what have different name)
What we need.
1. Cisco Connect for Mac OSX (i use snow leopard and Cisco Connect for E3000)
2. Terminal
Okay. Let's go.
1. Install Cisco Connect for OSX
2. After setup - slighty setup your cisco router (give something name and password), then, when cisco connect say you "You now connected the internet" and going to main screen - exit from cisco connect
3. Open Terminal (Or you can use Finder (go to Application, show package content Cisco Connect))
4. Go to /Application/Cisco Connect.app/Contents/Resources/lcid/<your setup language, for english - go 1033>/
5. Edit resource_strings.pus (vi resource_strings.pus)
6. Change "-guest" in string <LocalizableString RcFileId='10019' BaseTextHash='0xA65E286D' BaseText='-guest'/> for something what you want. For example, i changed for ' Guest Network'
7. Save
8. Open Cisco Setup
9. Go to router configuration and change desired name. I changed to 'Grizlly Bear'
10. After setup name - go to Guest Setting and Enable. As you can si, your guest network name set as 'Grizlly Bear Guest Network'
11.Exit Cisco Setup
12. Go to web interface setup
13. Setup Wifi manual and change SSID for diferent names. I change 5Gh to 'Grizlly Bear Hi-Speed Network' and 2.4GHz to 'Grizlly Bear Main Network'
14. Setup your hostname for all services (fileserver, media server, etc)
Woala!
We have three diferent names network!
Questions?

In order to enable Guest networking, the AirPort Extreme must be configured as your "main" Internet router. In this configuration, Connection Sharing = Share a Public IP address. The Extreme would be connected directly to the Internet modem and NOT downstream of another router with NAT enabled.
In this configuration, the Guest network would provide access ONLY to the Internet and NOT to your LAN.

L2tpv3 dialing from cisco router

I have requirement where customer wants ip dialing to LNS from cisco router with the help of l2tpv3.
Could anyone tell me how to configure this.
regards
shivlu jain

Hello Shivlu,
in one of our routers the backup link is configured in this way
pseudowire-class netvision-l2tp
encapsulation l2tpv2
interface Virtual-PPP1
description NETVISION DIALER
ip address negotiated
ip nat outside
ip virtual-reassembly
no cdp enable
ppp pap sent-username password 0 41003827
pseudowire x.x.x.x 2 pw-class netvision-l2tp
crypto map VPN_MAP
where x.x.x.x is a public ip address
ip route x.x.x.x 255.255.255.255 g0/1
completes this solution where this g0/1
sh run int gi0/1
Building configuration...
Current configuration : 157 bytes
interface GigabitEthernet0/1
description CONNECTION TO CABLE MODEM
ip address dhcp
ip virtual-reassembly
duplex auto
speed auto
media-type rj45
end
and it receives a private ip address from DHCP on a cable modem access network.
but it uses l2tpv2 not L2tpv3 and I've always seen l2tpv2 in this context.
Hope to help
Giuseppe

Curious message during activation of snmp traps in cisco router 2800

I activated snmp traps in cisco router 2800 (I didn't specify a set of them, so all of them were activated). The thing is, when i configure "snmp-server enable traps", appears a message in the next line :
" %Cannot enable both sham-link state-change interface traps.
%New sham link interface trap not enabled "
Anyway, traps are activated and are completely functional.
I would like to know, why this message appears... and also what is the difference between informs and traps, because I can activate both of the in a router to be sent to the network admin pc.
Thanks in advance.

Hi Marcelo,
the snmp-server enable traps command enables just all types of traps that the IOS version supports.
The message apperes because of this two, which are mutually exclusive:
R1(config)#snmp-server enable traps ospf cisco-specific state-change shamlink interfaceR1(config)#snmp-server enable traps ospf cisco-specific state-change shamlink interface-old% Cannot enable both sham-link state-change interface traps.% Deprecated sham link interface trap not enabled.
It's recommended to only enable the traps you really need.
Informs were introduced with SNMPv2, and they have the same format and purpose as traps.
The main difference is that traps are send in a hit-or-miss fashion whereas informs expect an acknowledge and will be re-send if unacknowledged.
Hope that helps
Rolf

Encapsulation dot1q is not working?, 2600 Cisco router

     I am trying to config a 2620 Cisco router to perform subintreface (F0/0.1) for Vlan Trunk Protocol, however when I try to configure the encapsulation dot1q, I continue to receive error massage with ^ symbol below the 'c' See below, the platform version is a 12.3(26) which should be acceptable to perform an (encapsulation dot1q). The Ethernet is a fast-Ethernet 10/100 port. I also try the ISL, I receive the same massage.
Can anyone suggest what could be the problem!!
Thank you all!!!!!
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int f0/0
Router(config-if)#no ip address
Router(config-if)#no shutdown
Router(config-if)#int f0/0.1
Router(config-subif)#encapsulation dot1q 1
^ % Invalid input detected at '^' marker. Router(config-subif)#
==================================================================================================== Router#show version
Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2008 by cisco Systems, Inc. Compiled Mon 17-Mar-08 15:23 by dchih ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1) Router uptime is 5 minutes System returned to ROM by power-on System image file is "flash:c2600-i-mz.123-26.bin" cisco 2620 (MPC860) processor (revision 0x600) with 28672K/4096K bytes of memory . Processor board ID JAD05440GAN (1508240486) M860 processor: part number 0, mask 49 Bridging software. X.25 software, Version 3.0.0. 1 FastEthernet/IEEE 802.3 interface(s) 1 Serial network interface(s) 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Router#
==================================================================================================
Router#sh flash
System flash directory:
File Length Name/status
1 7754580 c2600-i-mz.123-26.bin [7754644 bytes used, 633960 available, 8388604 total]
8192K bytes of processor board System flash (Read/Write)
Router#

jesse rodriguez wrote:I am connected through the console, Here are the output.Router#config t Enter configuration commands, one per line. End with CNTL/Z. Router(config)# Router(config)# Router(config)#int f0/0 Router(config-if)#no ip address Router(config-if)#no shutdown Router(config-if)# *Mar 1 00:01:36.891: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state t o up Router(config-if)# Router(config-if)#int f0/0.1Router(config-subif)#enc ? % Unrecognized commandRouter(config-subif)#en? % Unrecognized command Router(config-subif)#en ? % Unrecognized command Router(config-subif)#enJesse
It's possible your feature set it not good enough to run trunking.
Trunking apparently requires a minimum of the IP PLUS feature set according to this document
http://www.cisco.com/en/US/tech/tk389/tk815/technologies_configuration_example09186a00800949fd.shtml
table 2 shows a minimum IOS of 12.0(1)T and IPPLUS/IPPLUS on the 2620 - so your IOS revision is OK, but maybe your feature set is not.
You can figure which feature set you have by going here
http://tools.cisco.com/ITDIT/CFN/Dispatch?act=rlsSelect&task=search&searchby=image
and entering your image name (assuming it's not been stuffed with) which you can find by doing "show flash" or "dir"
If you don;t have the right feature set, then you're out of luck unless you can upgrade/change the IOS image the router is booting with.
Cheers.

QOS on 6500 routed interface

All of the QOS configuration guidance I've seen in the documentation on this website refers to 6500 switched interfaces (switchport mode access/trunk).
Is the QOS configuration different on a 6500 routed interface. For instance on an interface between two core switches in a routed (Layer 3) core?
I have already reviewed all of the IOS-related 6500 Cisco documents I could find, and the latest QOS SRND with no luck finding info on this issue.
Thanks
Greg

This URL should help you:
http://www.cisco.com/application/pdf/en/us/guest/products/ps708/c2001/ccmigration_09186a00801a90cc.pdf

Cisco router interface threshold

Similar Messages

Maybe you are looking for