Clear advanced sticky source ip sessions

I would like to clear advanced sticky source ip sessions every morning at 1am
is there a script or command to do this?
Thanks

You need to go into debug mode to purge the sticky entries
If you want to purge the entire table
CSS# llama
CSS(debug)# sticky-purge l3-sticky
To clear just one entry, specify the ip address and mask of the entry
CSS(config)# llama
CSS(debug)# sticky-purge l3-sticky 10.1.2.3 255.255.255.0
Hope it helps
Syed Iftekhar Ahmed

Similar Messages

CSS Balance srcip = sticky source ip?

Hi
Is the balance method "srcip" the same as the general method known as "sticky source ip"? Whereby, the same source ip will be directed to the same destination server by the CSS?
Thanks in advance.

sorry, but it looks like my explanation was not clear enough.
Let's take the following scenario.
We have 2 servers - A & B.
Initially A is down.
A client C connects to the vip and is therefore loadbalanced to B based on the srcip algorithm.
After a while, A comes alive.
C open a new connections with the VIP and this time the algorithm selects A.
So stickyness did not work.
With 'advanced-balance srcip' the first connection will go to B and a sticky entry will be created.
When the 2nd connection comes in with both A & B alive, the CSS will forward the connection to B based on the sticky table.
If B was down, the CSS would forward the connection to A and update the sticky table.
So, the advanced method gives you a better guarantee of stickyness.
As I said, the only problem is the sticky table.
Actually this is most of the time not a problem, but sometimes you could end up with the table being full and stickyness start failing. There is solutions to this problem so.
I hope this makes more sense like this.
Gilles.
With balance srcip

How to clear the variable value in session store?

I'll try to build form for search. There are LOV and
search button on form. When user don't select anything then push
search button, I'd like the report to show query everything. I
mean the report will show like condition where id like '%'.
And I send variable between form to report by using session
store.
I select nothing in LOV but value that return by LOV is
not null. It's in stead of old value of LOV.
Please tell me.. How to clear the variable value in
session store? I'd like to set it to null. If you have greater
way to do like this, please tell me.
Thank you.

Please suggest on this..
Thanks.

What are the various ways i can clear my previous(page displayed) session?

what are the various ways i can clear my previous(page displayed) session?
or at least one effective one.
here my requirement is when i reach to any page if i refresh or go to other page and come back it should not retain anything there.
session should get clear after every visit to any page or same page.
thanks
vijendra

hi
u can disable back button of browser using....
response.setHeader("pragma","no-cache");
response.setHeader("Cache-Control","no-cache");
response.setHeader("Cache-Control","no-store");

Is there a way to keep my app tabs set up if I clear my browsing history between sessions? (v. 4.0 on Mac OS 10.6.6)

Just downloaded version 4.0 yesterday, running on Mac OS 10.6.6. When I set up a few app tabs, they worked fine during the session but were gone when I restarted Firefox.
I usually have my preferences set to clear my browsing history, download history, forms, cache, active logins, and most cookies when I close Firefox. I changed them to clear everything else as usual but to remember my browsing history, and this seems to solve the problem - my app tabs reappeared when I restarted FF. Is there a setting I'm missing that would let me clear my history but maintain the app tabs across sessions?

Based on everything you have told us, Without a doubt, you need a lot more RAM installed in your iMac.
OS X 10.6 Snow Leopard can, at times, use up the full 4 GBs of RAM, for. itself, alone.
Your model iMac can take, a total of 16 GBs of RAM.
My advice is to install the max. 16 GBs of RAM.
Correct and reliable Mac RAM can be purchased from online Mac RAM sources Crucial memory or OWC (macsales.com).
RAM is user installable and very easy to do for beginning or novice computer users or novice computer upgraders.
http://support.apple.com/kb/ht3918
http://m.youtube.com/#/watch?v=XjU_NQh6e1k&desktop_uri=%2Fwatch%3Fv%3DXjU_NQh6e1 k
Good Luck!

Deduction of TDS while clearing Advance payment through F-53

Hi Gurus,
I deducted TDS on Advance payment of 10000 and then deducted TDS on Invoice of 50000 with base amount as 40000.
Now, when i am clearing this invoice and advance payment through F-53 to pay the remaining balance, system is again deducting TDS on Advance payment.
Please tell me how can i solve this issue.
Thank You

hii
here the steps u need to follow is
1. while making the down payment TDS is deducted
u make down payment through f-48.
2. post invoice through FB60. here when u r going to the withholding tax tab u need to delete the payment tax codes. if u do not delete than the tax will be deducted during the payment..
3. now go to F-54 and transfer the advance payment to normal by clearing special G/L
here when u clear the down payment the TDS deducted at he time of down payment will also be reversed.
4. now finally go to F-53 and make the outstanding payment to your vendor ..
so in this steps there wont be duplication of TDS pain.. u will be paying only once that is at the time of invoice.
Hope u got ur answer
assign points..
sejal singh

Use back button and clear advanced action and quiz answer..

OK, so I have made a quiz where the answer for each question is recorded and given in a list at the end. However, I would like the user to be able to go back and change their answer. At the moment if the user goes back, the answer is locked and they cannot chose a diiferent option.
Does anyone know if it is possible for them to go back, select a different and still have the advanced action part record the new answer?
Thanks for any help!

Only way to reset the answers to a default question slides, during the same session, is to use the Retake button on the score slide (you need to have multiple attempts of course. But that will be done at Quiz level: all answers are reset.
Another option (in CP6 and later) is to use the Submit all option, then they will be able to go back and change answers. But... I suppose you are using the system variable cpQuizInfoAnswerChoice to populate user variables with those advanced actions? That system variable is not populated when Submit all is chosen.
Last option is to use remediation, but it will probably not suit you: then user can be sent to a content slide if a question is failed, be sent back to the question slide and can then change the answer. It is not just going back one or more slides.
Custom question slides will allow what you want, but they necessitate a lot more work and you will not be able to use question pools.
Lilybiri

Clearing OS SPIDs for KILLED sessions

Hi All,
I had killed some sessions in the DB (10.2.0.3) and their status is set to KILLED in v$session.
I am trying to find the OS PIDs of these sessions to do a "kill -9 " but I could not get them. I am using the below query which is not returning anything as the entry does not exist in v$process:
select
p.spid
from v$session s, v$process p
where p.addr = s.paddr
and s.status='KILLED';
Is there any way to get the OS PIDs of these sessions or to clear the KILLED rows from v$session without bouncing the database.
Regards,
Bharath.

hi,
once you kill the user then his process and memory will be released..
post the output of v$session;
regards,
Deepak

Font Smoothing/Clear Type disabled on RDP Session, color depth low

Hello
One of our customers has a new laptop Asus G771JM-T7021H with Windows 8.1 on it. The graphics, font etc. is good as long as he works locally. When he connects to the terminal server (2012R2) via RDP, the resolution and font is hardly readable. It seems that
the clear type is disabled, everything is blurry and pixelated. The color depth seems to be very low. We've checked the RDP-configuration and the graphic card driver but couldn't find anything wrong.
Any ideas?

Solved in another (Hebrew) forum.
pacman -Syu

(Advanced JTable) source + screenshots

Hi
I am busy developing advanced JTables. I need a little help! Please have a look at www.geocities.com/javac_za . I also have posted my questions on the site. If you can help me please email me at [email protected]
Thank you javac_za

I have glanced at the code and here is my suggestion:
public void addJRadioButtonGroup(TableModel model)
   for(int row = 1; row < model.getRowCount(); row++)
      JRadioButton radio = (JRadioButton)model.getValueAt(row, 0);
      System.out.println(radio);
      group.add(radio);
public int getSelectedIndex()
for(int i = 1; i < model.getRowCount(); i++)
    JRadioButton radio = (JRadioButton)model.getValueAt(row, 0);
    if (radio.isSelected() return i;
return -1;
}Basically the getSelectedIndex is done the same way that the radio buttons are set up. I didn't look at the second question but surmise that it can be done the same way. The suggested change above has not been tested by me.
V.V.

CSM Sticky Source IP

Hello,
I need help configuring my CSM; I have a group of networks which need to be routed to a specific server based on their location.
I have a link which points to VIP:
http://1.1.1.1
If the request comes from source 2.2.2.0/24 they should be sent to http://1.1.1.2.
If the request comes from source 3.3.3.0/24 they should be sent to http://1.1.1.3.
What would be the best way to set ths up?
Thank you,
Scott

module ContentSwitchingModule 5
vlan 220 server
ip address 10.20.220.2 255.255.255.0
alias 10.20.220.1 255.255.255.0
vlan 221 client
ip address 10.20.221.5 255.255.255.0
gateway 10.20.221.1
alias 10.20.221.2 255.255.255.0
probe PING icmp
interval 2
retries 2
failed 10
receive 2
real SERVER1
address 10.20.220.10
inservice
real SERVER2
address 10.20.220.20
inservice
real SERVER3
address 10.20.220.30
inservice
real SERVER4
address 10.20.220.40
inservice
serverfarm WEBFARM
nat server
no nat client
real name SERVER1
inservice
real name SERVER2
inservice
probe PING
serverfarm WEBFARM2
nat server
no nat client
real name SERVER3
inservice
real name SERVER4
inservice
policy SOURCE-IP-50
client-group 50
serverfarm WEBFARM2
# A policy consists of a series of conditions, plus the
# actions to take if those conditions are matched.
# In this case, the only condition is "client-group 50"
# which requires the incoming connection to match
# the standard access-list 50
# The only action to take is to use serverfarm WEBFARM2
# to serve those requests.
vserver WEB
virtual 10.20.221.100 tcp www
serverfarm WEBFARM
persistent rebalance
slb-policy SOURCE-IP-50
# slb-policies associated to a vserver are always examined
# in the order in which they are configured.
# The defintion of the "serverfarm" under the vserver config
# is the default policy and is always used as last resort
# if no policy matches or if there are no policies
# In this case, incoming requests will be processed to see
# if they match the conditions of slb-policy SOURCe-IP-50
# If they do, then WEBFARM2 is used, otherwise the default
# policy is selected (i.e. WEBFARM will be used).
# If a default farm is not configured, then connections
# not matching any policy are dropped.
inservice
access-list 50 permit 10.20.1.100
# Configuration of the IOS standard access-list
# You can configure any of the 1-99 standard access-list
# or you can configure named access-lists

Pl Clear my doubts on Stateless session Bean

Is it necessry to Have isolation level and transaction attribute to be mentioned Stateless session Bean.
and where this to be done.
Help is highly appreciated

There are default (leaving transaction state alone) - so you don't have to specify it.
I'm open to correction: isolation level is specified by the vendor specific configuration whereas transaction attributes are defined in ejb-jar.xml
isolation level is a tuning parameter, whereas the transaction attribute is a design issue.
You shouldn't specify transaction where they don't need. I have seen a number of applications where full transaction level is specified on all methods, and then they wonder why their application is slow.
A transaction is only required if atomic operations are in place. For instance, you don't need transactions on a getter, you may need them though on a setter, iff the setter does more than one thing and those things depend on each other.

CSS sticky session when source ip changes

I work for an ASP and am having problems with customers dropping their ssl connection to our app across the internet on wireless connections. The customer was using a verizon wireless card and the ip assigned to his computer was a 70.x.x.x (ipconfig) but I had the user go to http://myipaddress.com because I could not see the ip on the sniff trace. The ip changed in the verizon network to a 66.x.x.x. I was able to trace the 66 ip and found that when the user was dropped his 66 ip changed. Has anyone experienced this?? I am looking for a long term fix. Currently SSL is termingation at the server farm and I am using a sticky source ip at 4 hours. I would be willing to move the ssl to the content switch if needed but what can i do to keep the same session after a source ip change?
Thanks,
Steve
CSSIP
CSSP

by terminating ssl on the css, you could use cookie stickyness which is independent of the ip address.
This would solve your problem for sure.
Without the SSL module, you don't have much option.
If you can't use IP address, you also can't use TCP ports, so the only thing left is the SSL ID.
You could 'advanced-balance ssl' with 'application ssl'.
However, IE browsers are known to change frequently the SSLID even during a single session.
So, by using this optin, you may fix the problem of this particular client but create more issues with other customer.
Unfortunately that's the only choices available.
Gilles.

CSM 12 hour stickiness from two source addresses

We have an environment where the traffic only originates from two source IP addresses (shared port forwarders). The server group need a 12 hour stickiness window for the Citrix sessions to be hitting the same server.
If we have two servers, ServerA and ServerB, this is the problem.
When maintenance is performed on ServerA. All traffic is sent to ServerB. When ServerA is back in operation the traffic does not use this server due to the sticky timeout of 720 minutes.
Is there anyway to clear the connections from one source on the CSM so the processing of packets will spread the load between the two servers?
Thanks.

Ben,
clearing the connections without clearing the sticky table is useless. Because the sticky entry will simply forward the new connections back to the same server.
Also, there is no way to clear a particular sticky entry.
Finally, I think the solution for you would be to create static sticky entry.
You can force a client ip to go to a specific server.
If the server is down for maintenance, the CSM will simply select another one but will go back to the initial one if available.
To configure static entries, use the following commands
sticky 66 netmask /32
static client source x.x.x.x real x.x.x.x
Gilles.

Program monitor blurry but source monitor is clear

Please...I have imported tifs at 1280x800, and they look clear in the source monitor, but when placed on the timeline, they look slightly blurry...noticeably blurry. Video does the same thing. What setting am I missing? Thx.

Sorry Jeff and Jim...actually OTS means over the shoulder...we used it in tv news...so it is a box that is superimposed like a picture in picture over the shoulder of an anchor...and we need it to be 4x3, or so we thought, because that is close to the size that the powerpoint is kicking out...hence the 1280x800. I can make the OTS any size we need to, just so it doesn't squish the words or distort them.
So the final product is widescreen 16:9, with a 4:3ish box (OTS)...all being used for online classes, final screen size yet to be determined, in flash.
That said, I cannot get a clean image in my timeline, even though the source monitor shows the image very clearly.
I would love to email one of the powerpoint images to someone who is willing so that they might load it up in premiere and help me out with the correct numbers for correct sizing out of powerpoint and into premiere.
I'm an old AVID cutter, (story editor for food network and HGTV for the last 8 years) trying to switch it up because premiere CS3 seems pretty powerful as I get more and more into it, and my avid seems slower than usual, undependable.
I dont know the terminology as well as I should, depended on IT guys a little too much on our production systems...now I am on my own with relatively new machines and, well, it FEELS like I am on my own! any help you could provide, it goes without saying, would be a Godsend. Willing to learn. Need to get this project fixed, and soon. thx.

Clear advanced sticky source ip sessions

Similar Messages

Maybe you are looking for