Computer locks up transferring TCP/IP data to labview vi
Hello,
I am transferring data to a Labview v7.1 vi and the computer locks up after several minutes data transfer. The amount of data transferred is continuous for this time period. Are there suggestions for dealing with this issue?
Thanks,
Ron
Hello,
When you say your computer locks, does that mean just your VI or all applications?
It's possible that LabVIEW is consuming much of the CPU, especially if it's the only application running, and you don't have any timing/wait functions in a loop. In such a case you can imagine that code is executing as fast as possible, and if nothing else is running on the machine, it can appear as though things lock up.
Try using the wait until next ms multiple or wait ms function.
Best Regards,
JLS
Best,
JLS
Sixclear
Similar Messages
-
K7D Master-L MS-6501 computer locks up when transferring data to external HD
I'm not 100% sure the problem is with the motherboard, but I think I've narrowed it down to the point that the MB could be the problem, and so I figured it was worth a shot to see if anyone else had heard of this problem or perhaps had any suggestions as to what it could be...anyway...
Here's the problem: whenever I try to transfer large data files onto my LaCie 250GB external HD, my computer locks up completely. No CTRL+ALT+DEL. No Pass Go (and certainly no $200 :P). The connection interface is USB 2.0, to which I use the USB 2.0 controller card that came with my MB. When I connected the HD to my laptop (Dell Inspiron 5150, I think), it transferred the files flawlessly. Also, when I connected the drive to my roommate's desktop (another homemade system, though much beefier), it also read from/wrote to the HD without a hitch. I even tried connecting the HD to my laptop, and (since my desktop & laptop are on the same network) mapped the HD onto my desktop as a network drive. Then I transferred 24GB+ of data w/o any lock ups or problems whatsoever. However, when I reconnected the HD back to my desktop and tried transferring a little over 500MB worth of files, it locked up after getting about 75% through. I even tried disconnecting all of USB devices but the HD (and my mouse) and it still locked up after getting so far w/ the transfer.
The issue doesn't seem to be a data-throughput issue, b/c it transferred just fine when the HD was mapped as a network drive, and the drive works flawlessly on other computers, so I don't think the problem is in the drive itself (or the cable). The only time there is an issue is when the HD is connected to my desktop via any USB port (I've tried both the on-board ports as well as the controller card ports). Have any of you guys (or gals) ever heard of such an issue? I hesitate to say it's the ports themselves b/c I've got about 8+ USB devices connected to my computer at any given time, and none of them have any issues communicating back and forth (nor have they ever locked up my machine like it's doing now). A couple of friends have suggested that it might be a driver or BIOS issue, but I can't seem to find any USB driver updates for my MB model (I have only the ones on the disc that came w/ my MB) and the MSI website warns not to flash the BIOS if everything is running ok with your computer (which it is, minus this issue). My BIOS version is 1.6 (probably should've put that w/ my signature :P)
I hope this is enough info to go on. Any help or suggestions would be greatly appreciated. Thanks for your time!To my knowledge, both of the other systems it was tested on had SP1 installed (I know that's the case on my laptop).
I dunno if it would make a difference, but my laptop has WinXP Home, whereas my desktop has Pro installed. -
I have updated to a new windows 7 computer, and after transfering my itunes library via iphone, itunes has locked me out of the app section of my phone. I can not add or remove apps using itunes. Is there a way to fix this? I have authorized, deauthorized, restarted, rebooted, and reset both my computer and iphone. Anyone got any ideas?? Thank you!
The safest way to do this would be to copy your itunes library to an external drive. For the purposes of this excersize the new Laptop would be the external drive
Here is the support article
http://support.apple.com/kb/ht1751
Then you could erase the iPhone and resync it without losing any content.
If this option is not open to you then this article contains ways to get your content off your iPod
https://discussions.apple.com/docs/DOC-3991 -
Computer crashed ! Will all iPhone data be transferred to new empty iTunes ?
Title says it all:
My computer crashed, so will all the data (music, books, pictures, apps, data inside apps, folder organisation, apps' logins and passwords, ) currently inside my iPhone be transferred to the new empty iTunes ?
I don't care about Notes and Contacts which are synced to iCloud.
Or will the empty new iTunes empty my iPhone ?Sorry but you know nothing about my story and what happened with my computer so please don't barge in with wrong conclusions and make a fool of yourself.
Fortunately there are helpful people around such as wjosten to hep and not judge.
Not to mention saying things such as "It's also counterintuitive to believe that a cell phone is a backup device."
Who believes that ? Who are you talking to ? Certainly not me. As it's exactly the opposite: originally sync has been created to back up your device on a computer. The computer is the back up, not the device. And when your back-up fails anybody expects to be able to copy ALL your data simply from the original drive to another back-up drive.
Apple's one-way-only method is ABSOLUTELY counter-intuitive, you will find coultless topics on the internet of people not getting it and having issues with this and software such as Phoneview, DiskAid, IExplorer, etc... being created by third-parties to compensate Apple's weaknesses.
Just another example : I would be happy to know why they had to wait "the Third Millennium, over 30 years since the first consumer-oriented computer became available" to add the ability to sync contacts and calendars between a Mac and iOS device via USB connection, available only now since OSX 10.9.3 !!...
Apple has certainly made historically good choices over the years, but no matter how difficult it is to admit for some people it also has made and stuck to other very poor choices. And this is one of them, right there... -
I'm overseas and need to sync my iphone with itunes but I don't have my computer. How can I sync it to my friends computer without losing my music and data?
Why do you need to sync your iPhone with iTunes - for what purpose?
You can transfer iTunes content and photos from one computer only. When transferring iTunes content and photos from another computer, all iTunes content and photos transferred from a different computer will be erased from the iPhone first with a warning message provided beforehand indicating this will occur. -
i hate it i am fed up it so diffiuclt Why they make it so difficult with transferring photos contacts data from iphone 5s to pc .!!!!!!!!!!!!!!!!!!!!!!!!!!!
Hook the phone to the computer, open the Computer icon and look for the iPhone folder. Copy the images. Not difficult at all. Sync your contacts with Outlook through iTunes. Not really so difficult.
-
I HAVE BEEN USING AN IPHONE 4 AND I JUST TRANSFERRED ALL MY DATA TO A NEW IPHONES.
IN THE OLD IPHONE I HAD 2 YAHOO AVVOUNTS RECEIVING MAILS.
IN THE NEW IPHONE I CANNOT REGISTER MY SECOND YAHOO ADDRESS ,I KEEP RECEIVING THE MESSAGE THAT YAHOO SERVER CANNOT BE FOUND.
CAN ANYBODY HELP?The reason, I included the annotation that I'd upgraded my Itunes, (On my Computer) is B/C in many forums - the very first question, *HELPERS* ask, is. "Do you have the latest version of Itunes downloaded on your computer." I wanted to knock out any obvious replies.
Now- "DO YOU have any idea,"... how your UNHELPFUL remarks, do absolutely nothing but hurt others that might not have the EXPERIENCE you have? How do you expect people to know things without asking questions? Whew! RUDE!!
Message was edited by: Apple I0S Help Team -
Transferring Outlook Express Data from G-3 to G-4, Help Needed, please
Hi, I would like some help: I think I transferred my HD from G-3 to G-4, but none of the data of my Outlook Express 5.02 on the G-3 made the firewire jump. How do I:
a. find out if the data (inbox, sent msgs, folders, etc.) are on the G-4
b. if they are not there, how do I get them to transfer. All the other folders on my hard drive, data, documents, etc., went across well (it took an hour to transfer the HD, which was about 7 Gb)
Any help is appreciated, you may e-mail me personally at [email protected]
Thanks, Paul
G3 & G4 Mac OS 9.2.x Transferring Outlook Expr Data from G-3 to G-4
G3 & G4 Mac OS 9.2.xpagarciakcmo:
Welcome to Apple Discussioins.I think I transferred my HD from G-3 to G-4What does this mean? Can you tell us a bit more and the procedure you used? Transferinng your HD from G3 to G4, does that mean you took the HDD from one computer and placed it in another?firewire jumpSorry about all these questions, but what do you mean by "firewire jump"?
Can you give some more specific details about your G3 and G4 computers?
Good luck.
cornelius -
I have a mac book, with office for mac and iStudio installed. When I try to create a document using either one of these; after inserting several photos, the computer locks up and the only way I can get it to unlock is to do a force quit. Why does it do this, and how can I get it to unlock without having to do a force quit?
Are you using versions of the software that are compatible with the version of OS X you have installed? Very often such lockups are caused by application incompatibility.
The problem may also come from trying to use both sets of applications at the same time while not having enough RAM installed. Adding more RAM may fix the problem.
The problem can arise from corrupted support files such as preference files or Application Support files or corrupted cache files.
The image files you are using may also be corrupt thus causing the problem.
You might start with:
Kappy's Personal Suggestions for OS X Maintenance
For disk repairs use Disk Utility. For situations DU cannot handle the best third-party utilities are: Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible. TechTool Pro provides additional repair options including file repair and recovery, system diagnostics, and disk defragmentation. TechTool Pro 4.5.1 or higher are Intel Mac compatible; Drive Genius is similar to TechTool Pro in terms of the various repair services provided. Versions 1.5.1 or later are Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts had been significantly reduced in Tiger and Leopard. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems.
I would also recommend downloading the shareware utility TinkerTool System that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc. Other utilities are also available such as Onyx, Lion Cache Cleaner, CockTail, for example.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the commandline. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand. I also recommend booting into safe mode before doing system software updates.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
Backuplist
Carbon Copy Cloner
Data Backup
Deja Vu
iBackup
JaBack
Silver Keeper
MimMac
Retrospect
Super Flexible File Synchronizer
SuperDuper!
Synchronize Pro! X
SyncTwoFolders
Synk Pro
Synk Standard
Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac Maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate. -
Yosemite: Computer locks up (rolling beachball) during startup
23-Oct2014
Apple Support Community:
I have had nothing but problems installing Yosemite on my new Mac Pro. I bought the computer about six months ago as soon as they were averrable.
After I push the start button, it take at least 5 minutes for the computer to get to my login screen so I can enter my password. Then it taks 10 minutes of the rolling beachball to allow me to actually enter my password. Then the computer locks up. I have had it run beyond an hour. before pushing the off button.
I have tried using disk utility disk repair and permissions repairs on all the attached hard drives.
Also, I have had lots of problems downloading podcasts on iTunes. Getting podcasts is one of the main purposes I use my home computer for.
Anyway, how do I get Yosemite to work for me instead of locking up with the rolling beachball?
Thank you for any help you can give me.These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
For this step, the title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.
In the top right corner of the Console window, there's a search box labeled Filter. Initially the words "String Matching" are shown in that box. Enter "BOOT_TIME" (without the quotes.)
Each message in the log begins with the date and time when it was entered. Select the BOOT_TIME log message that corresponds to the last boot time when you had the problem. Now clear the search box to reveal all messages. Select the ones logged after the boot, during the time something abnormal was happening. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
For example, if the problem is a slow startup taking three minutes, post the messages timestamped within three minutes after the boot time, not before. Please include the BOOT_TIME message at the beginning of the log extract—not at the end.
If there are long runs of repeated messages, please post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A crash report has a name that begins with the name of the crashed process and ends in ".crash". A panic report has a name that begins with "Kernel" and ends in ".panic". A GPU restart report has a name that begins with "Kernel" and ends in ".gpuRestart". Select the most recent of each. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
I know the report is long, maybe several hundred lines. Please post all of it anyway.
If you don't see any reports listed, but you know there was a crash or panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful. -
Computer locks up after burning a music CD to Itunes
Just purchased a new Nano 8Gb IPOD,... loaded Itunes 8 updates to my PC,.... when I try to burn a CD to Itunes,.. at the end, the computer locks up,... the files will be transferred,.. but this is a real pain if it locks up after every CD...... Has anyone else experienced this?? I'm running Window XP, have the Version 2 Operating System. Any help is greatly appreciated.
Thanks!!!the last time I tried to burn a cd from itunes, my system crashed and my optical (a new dual layer superdive installed less than a year ago) died... I haven't a clue what happened!
I ended up buying an external and though itunes recognizes it, when I try to burn an audio cd (mp4 to aiff), it goes through the entire process of 'seemingly' converting the files, the cd shows ALL the information, even when re-inserted into the drive... but there's NO actual information on the disc. It 'appears to play' but no sound comes out and there's no activity in the equalizer at all.
On external cd players, one player did the exact same thing and another just refused to even see the cd as readable.
I've also tried burning from Toast, which ALWAYS worked in the past, with the same result.
What's the point of purchasing music in itunes if I can't burn the music to cd?
has anyone been able to solve this?
thanks... namaste -
Whenever I try to add music to Itunes, my computer locks up. This never happened until I update itunes to the latest version. How do I get around this?
Welcome to the Apple Community.
In order to change your Apple ID or password for your iCloud account on your iOS device, you need to delete the account from your iOS device first, then add it back using your updated details. (Settings > iCloud, scroll down and hit "Delete Account")
Providing you are simply updating your existing details and not changing to another account, when you delete your account, all the data that is synced with iCloud will also be deleted from the device (but not from iCloud), but will be synced back to your device when you login again.
In order to change your Apple ID or password for your iCloud account on your computer, you need to sign out of the account from your computer first, then sign back in using your updated details. (System Preferences > iCloud, click the sign out button)
In order to change your Apple ID or password for your iTunes account on your iOS device, you need to sign out from your iOS device first, then sign back in using your updated details. (Settings > iTunes & App store, scroll down and tap your ID)
If you are using iMessages or FaceTime, you will also need to log out and into your ID there too. -
Computer Locking Up at Random Issue
I am having an issue with the computer locking up when the side panel is in place and I am doing windows updates where its constantly processing and lots of hard drive activity. I am kind of thinking that its something to do with possibly the processor overheating but I am not for sure and would like to ask for advice here from others who have more experience with that this might be able to point me in the right direction.
I have an MS 6590 Ver 1 main board, with an AMD Athlon 2500+ processor. The hard drive is brand spankin new just bought it today April 2nd (WD 160GB). I have a dual fan power supply (Antec 350 watt) and a fan in the front, a fan in the rear, and one on the processor.
I have removed the side panel and am going to leave it off for a while to see if that stops the lock ups, if so then i guess i can assume that overheating is what is causing this, and then i just need to find out what is overheating.
What can I do to try and trouble shoot whats causing the lockups? Anyone have any further advice?
Thanks
DougQuote
I have an MS 6590 Ver 1 main board
Which one exactly?
http://global.msi.eu/index.php?func=searchresult&keywords=ms-6590
Quote
The hard drive is brand spankin new just bought it today April 2nd (WD 160GB)
IDE? SATA?
Did you have any problems with the old hard drive? -
Hi - I would like to build the logic in which it should accomodate the communication redundancy using serial RS-232 for Data Transfer b/w Host and RT irrespective of TCP/IP Data Transfer.
I want to do data transfer b/w host and RT through RS232 VISA portal whenever TCP/IP ethernet cable has been unplugged from the controller continuosly , it should keep on checking for TCP/IP link re-establishing also , when ever the tcp/ip link established again that time the communication should be using in that link only. This is accomplished by deploying the RT vi as execuatbale file. I made some logic regards to the above said logic , bur it was not working as much I expected.
I request you to go through the attached two VI's and let me know , what I did wrong in that,
Please do the needful.
Attachments:
TCP_Serial_Host.vi 33 KB
TCP_Serial_RT.vi 41 KBeven i am new to this topic and i am trying to get familiar with these protocols
refer to tcp server/client examples in labview examples -
I keep getting the following message every time i plug in my Iphone3gs to Itunes on my windows vista computer
Itunes was unable to load data class information from sync services. reconnect or try again later.
any suggestions pls
MarioThe article says that I should upgrade to the latest iTunes. I am on the latest iTunes version.
If you could read just a tiny little bit further, under the "Additional Information" section immediately after that, it says:
If you are still experiencing this issue when syncing, or have not installed Xcode 4 and get this alert:
Follow the troubleshooting steps in Mac OS X v10.5, v10.6: Resetting the SyncServices folder.
If the issue is still unresolved, follow steps in Sync Services: Advanced troubleshooting for contact and calendar syncing.
Have you tried those measures?
Maybe you are looking for
-
It seems that someone had access to my apple ID and password. This person logged in to my game center and changed the content of many games. As soon as i discovered, I changed my password so they won't be able to access my account again. Unfortunatel
-
Help required understanding the purpose of having instance Init blocks
I want to know exactly what the purpose of having instance initialization blocks in Java. As in static init blocks, we can execute some commands before creating an instance of a class. And also in instance init blocks, we are executing some commands
-
Short dump while extracting data
Hi, When i extract the data from the datasource 2lis_05_item in rsa3 i m getting the following short dump. Can anyone tell what to do in this case? Runtime Errors CONNE_IMPORT_WRONG_STRUCTURE Exceptn CX_SY_IMPORT_MISMATCH_ERROR
-
How to send the transport request from one client to other client?
Hello Friends, I have generated one transport request in one of the client in Development server.Now as it is customizing request so unless and until i transport it to other client within the same server, Changes will not be visible in other clients
-
HT4650 My Mac book has got a virus how can I get rid of it
Dose any body have any info that can help meu